AMG AMG2641 Instruction Sheet

AMG
Brand
AMG
Model
AMG2641
Type
Instruction Sheet

AMG AMG2641 is a four-channel video-only standalone transmitter designed to transmit four video signals on a single multimode optical fiber. It is powered from an AMG2002 power supply and is intended to work with the AMG2642R four-channel video receivers. The device features four 75-ohm BNC socket video input connections and one ST optical output. It also has a removable screw terminal connector for power input, with a power requirement of 12 to 16 volts DC at 750mA.

AMG AMG2641 is a four-channel video-only standalone transmitter designed to transmit four video signals on a single multimode optical fiber. It is powered from an AMG2002 power supply and is intended to work with the AMG2642R four-channel video receivers. The device features four 75-ohm BNC socket video input connections and one ST optical output. It also has a removable screw terminal connector for power input, with a power requirement of 12 to 16 volts DC at 750mA.

AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 1of 2 AMG2641 Instruction
Sheet D15249-01
AMG2641
Instruction Manual
Four Channel Video Only Standalone Transmitter
The AMG2641 is a standalone four channel video transmit unit designed to transmit four video signals
on a single multimode optical fibre. It is designed to be powered from an AMG2002 power supply.
The AMG2641 is designed to operate with the AMG2642R four channel video receivers.
Connections
Video Input Connections
Connector ...........................................4 off 75 ohm BNC Socket.
Input Impedance..................................75 ohm terminated.
Input Level ...........................................1 volt p-p nominal
Frequency Response ..........................10Hz to 5.75MHz min.
Optical Connections
OPTO OUT
Connector............................................ST
Optical Launch Power .........................-5dBm
Wavelength..........................................1310nm
AMG
2641
4 Channel Video
Transmitters
TX
O O
RX
OPTO SYNC
FRONT PANEL INDICATORS
VIDEO PRESENT
CH1 O O CH2
CH3 O O CH4
POWER
O
GND
+12-16 Volts dc
OPTO IN
VIDEO CH 1
VIDEO CH 2
VIDEO CH 3
VIDEO CH 4
OPTO OUT
GND
OUT-
OUT+
IN-
IN+
DATA
CONNECTIONS
INTERNAL
RS422/485
SWITCHABLE
*
TX
O O
RX
DATA PRESENT
167mm Overall
155mm between mounting slot centres
(4mm slots)
122mm Between
Slot Centres
132mm Overall
AMG Systems Ltd. reserves the right to make changes to this document without
notice. The information herein is believed to be accurate. No responsibility is
assumed by AMG for its use.
Page 2of 2 AMG2641 Instruction
Sheet D15249-01
Power Connection
Connector............................................removable screw terminal connector (3.5mm spacing)
Manufacturers Part No. Phoenix/Combicom MC1-5/2-ST-3.5
AMG Part No.G00047-00
Power requirement ..............................12 volts to 16 volt DC @ 750mA (1
amp turn on current)
Connections.........................................See schematic
+12 – 16 Volts on lower pin
0 Volts on upper pin
Indicators
Power...................................................Green – unit powered
Off – no power applied to unit
Opto Sync TX ......................................Green - optical channel transmitting
Off - optical channel not transmitting
Video Present CH1 to CH 4.................Green – video signal present on video CH1 input BNC
Off – no video present on video CH1 input BNC
Physical Information
Dimensions
Height ..................................................109mm
Width....................................................218mm
Depth ...................................................70mm
Weight..................................................500grams
Mounting Details
The unit is designed to be mounted into a panel via the two mounting slots of 4.5mm x 10mm.
Safety
The 2600 series of products uses a Class 1 laser system in accordance with EN 60825-2:2000.
However it is always advisable to follow good practice when working with optical fibre systems. This
includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre ends or
connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with the optical fibres systems see EN
60825-2:2000 or your local safety officer.
Maintenance
There are no user serviceable parts within the AMG2600 products.
In case of problem or failure contact your local support centre or AMG Systems Ltd, Technical Support
Department on tel. +44 (0) 1767 600777.
See unit data sheet for full specification.
O volts (Chassis)
+ 12 – 18 volts
  • Page 1 1
  • Page 2 2

AMG AMG2641 Instruction Sheet

AMG
Brand
AMG
Model
AMG2641
Type
Instruction Sheet

AMG AMG2641 is a four-channel video-only standalone transmitter designed to transmit four video signals on a single multimode optical fiber. It is powered from an AMG2002 power supply and is intended to work with the AMG2642R four-channel video receivers. The device features four 75-ohm BNC socket video input connections and one ST optical output. It also has a removable screw terminal connector for power input, with a power requirement of 12 to 16 volts DC at 750mA.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers