Gigabyte 6CX7 Series User manual

FCC Compliance Statement:

This equipment has been tested and found to

comply with limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable

protection against harmful interference in

residential installations. This equipment

generates, uses, and can radiate radio

frequency energy, and if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause interference to radio or

television equipment reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Move the equipment away from the receiver

-Plug the equipment into an outlet on a circuit different from that to which

the receiver is connected

-Consult the dealer or an experienced radio/television technician for

additional suggestions

You are cautioned that any change or modifications to the equipment not

expressly approve by the party responsible for compliance could void Your

authority to operate such equipment.

This device complies with Part 15 of the FCC Rules. Operation is subjected to

the following two conditions 1) this device may not cause harmful interference

and 2) this device must accept any interference received, including interference

that may cause undesired operation.

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2. 1077(a)

Responsible Party Name: G.B.T. INC.

Address: 18305 Valley Blvd., Suite#A

LA Puent, CA 91744

Phone/Fax No: (818) 854-9338/ (818) 854-9339

hereby declare s that the product

Product Name:

Model Number:

Mother Board

Conforms to the following specifications:

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

Supplementary Information:

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful

and (2) this device must accept any inference received, including

that may cause undesired operation.

Representative Person's Name: ERIC LU

Signature:

Date: Feb. 29, 2000

Eric Lu

GA-6CX7

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-6CX7

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

EN 55011 Limits and methods of measurement EN 61000-3-2* Disturbances in supply systems caused

of radio disturbance characteristics of EN60555-2 by household appliances and similar

industrial, scientific and medical (ISM electrical equipment “Harmonics”

high frequency equipment

EN55013 Limits and methods of measurement EN61000-3-3* Disturbances in supply systems caused

of radio disturbance characteristics of EN60555-3 by household appliances and similar

broadcast receivers and associated electrical equipment “Voltage fluctuations”

equipment

EN 55014 Limits and methods of measurement EN 50081-1 Generic emission standard Part 1:

of radio disturbance characteristics of Residual, commercial and light industry

household electrical appliances,

portable tools and similar electrical EN 50082-1 Generic immunity standard Part 1:

apparatus Residual, commercial and light industry

EN 55015 Limits and methods of measurement EN 55081-2 Generic emission standard Part 2:

of radio disturbance characteristics of Industrial environment

fluorescent lamps and luminaries

EN 55020 Immunity from radio interference of EN 55082-2 Generic immunity standard Part 2:

broadcast receivers and associated Industrial environment

equipment

EN 55022 Limits and methods of measurement ENV 55104 Immunity requirements for household

of radio disturbance characteristics of appliances tools and similar apparatus

information technology equipment

DIN VDE 0855 Cabled distribution systems; Equipment EN 50091- 2 EMC requirements for uninterruptible

part 10 for receiving and/or distribution from power systems (UPS)

part 12 sound and television signals

CE marking (EC conformity marking)

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

EN 60065 Safety requirements for mains operated EN 60950 Safety for information technology equipment

electronic and related apparatus for including electrical business equipment

household and similar general use

EN 60335 Safety of household and similar EN 50091-1 General and Safety requirements for

electrical appliances uninterruptible power systems (UPS)

Manufacturer/Importer

Signature : Rex Lin

(Stamp) Date: Feb. 29, 2000 Name : Rex Lin

6CX7

100/133 MHz Pentium II/III

Socket 370 Processor Motherboard

USER'S MANUAL

Socket 370 Processor Motherboard

REV. 1.0 First Edition

R-10-01-000216

How This Manual Is Organized

This manual is divided into the following sections:

1) Revision History Manual revision information

2) Item Checklist Product item list

3) Features Product information & specification

4) Hardware Setup Instructions on setting up the motherboard

5) Performance & Block Diagram Product performance & block diagram

6) Suspend to RAM & Dual BIOS Instructions STR installation & Dual BIOS

7) Four Speaker & SPDIF Four Speaker & SPDIF introduction

8) BIOS Setup Instructions on setting up the BIOS software

9) Appendix General reference

Table Of Contents

Revision History P.1

Item Checklist P.2

Summary of Features P.3

6CX7 Motherboard Layout P.5

Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition P.6

Performance List P.30

Block Diagram P.31

Suspend to RAM Installation P.32

Dual BIOS Introduction (Optional) P.38

Four Speaker & SPDIF Introduction (Optional) P.45

Memory Installation P.50

Page Index for BIOS Setup P.52

Appendix P.82

6CX7 Motherboard

1

Revision History

Revision Revision Note Date

1.0 Initial release of the 6CX7 motherboard user’s manual. Feb.2000

The author assumes no responsibility for any errors or omissions that may appear in this

document nor does the author make a commitment to update the information contained herein.

Third-party brands and names are the property of their respective owners.

Feb. 16, 2000 Taipei, Taiwan, R.O.C

Item Checklist

2

Item Checklist

þThe 6CX7 Motherboard

þCable for IDE / Floppy device

þCD (IUCD) for motherboard utilities

oInternal COM B Cable (Optional)

oInternal USB Cable (Optional)

oCable for SCSI device

þ6CX7 User’s Manual

þCRIMM Module

6CX7 Motherboard

3

Summary Of Features

Form factor Ÿ 30.5 cm x 20 cm ATX Size form factor, 4 layers PCB.

CPU Ÿ Socket 370 Processor

Ÿ 2nd cache in CPU (Depend on CPU)

Chipset Ÿ 82820 HOST / AGP / RDRAM Controller

Ÿ 82801AA(ICH) I/O Controller Hub

Clock Generator Ÿ Supports 100 / 133MHz

Ÿ 105/110/117/120/125/127/135/137/140/145/150 MHz clocks

(reserved)

Memory Ÿ 2 184-pin RIMM Sockets

I/O Control Ÿ Winbond W83627HF

Slots Ÿ 1 AMR (Audio Modem Riser) slot

Ÿ 1 Universal AGP slot

(1X / 2X / 4X 1.5V/3.3V device support)

Ÿ 5 32-bit Master PCI Bus slots

On-Board IDE Ÿ An IDE controller on the Intel 82801AA (ICH) PCI chipset

provides IDE HDD/ CD-ROM with PIO, Bus Master (Ultra

DMA33/ATA66) operation modes

Ÿ Can connect up to four IDE devices

On-Board Peripherals Ÿ 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes

Ÿ 1 Parallel ports supports EPP/ECP mode

Ÿ 2 Serial Ports (COM A & COM B)

Ÿ 4 USB ports (Front USB is optional)

Ÿ 1 IrDA connector for IR/CIR (Optional)

Hardware Monitor Ÿ CPU/Power Supply/System Fan Revolution detect

Ÿ CPU / Power / System Fan Control

Ÿ System Voltage Detect

Ÿ CPU Overheat Warning

Ÿ Chassis Intrusion Detect

Ÿ Display Actual Current Voltage

PS/2 Connector Ÿ PS/2 Keyboard interface and PS/2 Mouse interface

BIOS Ÿ Licensed AMI BIOS, 4M bit FLASH ROM

Ÿ Support Dual BIOS (Optional)

To be continued…

Summary of Features

4

On-Board LAN Ÿ Intel GD 82559(Optional)

Ÿ Alert On LAN*2 ASIC (Optional)

On-Board Sound Ÿ Creative CT5880 sound (Optional) and AC’97 codec

Line In/Line Out/Mic In/AUX In/CD In/TEL/Game Port/

SPDIF(Optional)/Four Speaker(Optional)

Additional Features Ÿ Internal/External Modem Wake up

Ÿ STR (Suspend-To-RAM)

Ÿ Wake On LAN

Ÿ PS/2 Keyboard Password Wake up

Ÿ System after AC back

Ÿ Poly fuse for keyboard, USB, Game port over- current protection

Ÿ PS/2 Mouse Power On

Ÿ USB KB/MS Wake Up from S3

6CX7 Motherboard

5

6CX7 Motherboard Layout

6CX7

ICH

82801

MCH

82820

Game & Audio

COM B COM A LPT

PS/2

BZ1

IDE1

FLOPPY

IDE2

AMR

PCI1

AGP

PCI 2

PCI 3

PCI4

PCI 5

Backup

BIOS

Main

BIOS

JP14

PGA 370

CPU

RIMM 1

USB

LAN

RIMM 2

Creative

CT5880

AOL*2

ASIC

SW1 BAT1

JP16

JP3

JP1

J1

JP18 JP15

J15

J7

J6

J8

J17

ATX Power

JP6

JP5

JP11

Intel

82559

AC’97

JP24

JP20

J2

JP17 J10 JP4 JP9 JP10 J11

J12

J18 J14

CN8

JP21

JP27

JP28

CN9

J16

JP8

LED1

JP29

6CX7 Motherboard Layout

6

$

Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition Page

CPU Speed Setup P.8

Connectors P.9

Game & Audio Port P.9

COM A / COM B / LPT Port P.9

USB & LAN Connector (LAN is optional) P.10

PS/2 Keyboard & PS/2 Mouse Connector P.10

J1 (CPU Cooling FAN Power Connector) P.11

J17 (Power Cooling FAN Power Connector) P.11

J16 (System Cooling FAN Power Connector) P.12

ATX Power P.12

IR/CIR (Optional) P.13

Floppy Port P.13

IDE 1(Primary)/ IDE 2(Secondary) Port P.14

J8 (AUX_IN) P.14

J6 (CD Audio Line In) P.15

J7 (TEL) P.15

J2 (Wake On LAN) P.16

J10 (Ring Power On) P.16

CN8 (Front) USB Port [Optional] P.17

J15 (External SMBUS Device Connector) P.17

JP15 (STR LED Connector) & LED1 (RIMM LED) P.18

CN9 (FP USB)[For NEC] [Optional] P.18

J12 (Front Panel Jumper)[For NEC] P.19

J18 (AOL Connector) [For NEC] [Optional] P.19

Panel and Jumper Definition P.20

J11 (2x11 pins jumper) P.20

JP16 (PS/2 Keyboard Power On) P.21

JP3 (Back USB device Wake Up Selection)[Optional] P.21

JP4 (Clear CMOS Function) P.22

JP5 (Safe mode/ Recovery / Normal) P.22

JP6 (Timeout Reboot Function) P.23

JP11 (AMR Select)[Optional] P.23

JP17 (Case Open) P.24

JP20 (Onboard Sound Function Selection) P.24

6CX7 Motherboard

7

JP21 (Front USB device Wake Up Selection)[Optional] P.25

JP27/JP28 (USB Port Select) P.25

6CX7 Motherboard Layout

8

JP9 (Top Block Lock) P.26

JP10 (FWH Write Protection) P.26

JP14 (Internal Buzzer Connector) [Optional] P.27

JP18 (STR Enable) P.27

JP29 (Over Voltage CPU Speed Up)[Optional] P.28

JP1 (Cyrix CPU Turbo Function) [Optional] P.28

JP24 (Onboard LAN Function) [Optional] P.29

BAT1 (Battery) P.29

CPU Speed Setup

8

CPU Speed Setup

The CPU bus frequency can be switched at 100MHz and 133MHz by adjusting JP8 & SW 1. The

CPU ratio selection is control by BIOS.

JP8 / SW1 Select the CPU Speed at 100MHz and 133MHz.

AGPCLK 66.6 73.3 80 66.6 70 75 66.6

CPUCLK 100 110 120 133 140 150 100/133/Auto

JP8 OFF OFF OFF OFF OFF OFF ON

1 O O O X X X X

2 O X X O X X O

3 X O X X O X X

4 O O X O X X O

(O: ON / X: OFF)

SW1

ON

JP8

1

100MHz

JP8

1

133MHz

JP8

1

100/133/Auto

SW1

ON

SW1

ON

1 2 3 4

6CX7 Motherboard

9

Connectors

Game & Audio Port

MIC In

Game

Port

Line In

Line Out 1

Line Out 1: Line Out or SPDIF (The SPDIF output is

capable of providing digital audio to external speakers

or compressed AC3 data to an external Dolby digital

decoder). In general, Line Out 1 is normally Line Out,

when it output digital signal, it will be change to SPDIF

Out automatically (see page 47 for more information).

Line In: In general, Line In is normally Line In. When

you select “Four Speaker” in Creative application

(see page 45 for more information), Line In will be

change to Line Out 2, then you can plug 2 pairs stereo

speaker into Line Out 1 and Line In simultaneously.

COM A / COM B / LPT Port

COM A

LPT Port

COM B

Connectors

10

USB & LAN Connector (LAN is optional)

Pin No. Definition

1 USB V0

2 USB D0-

3 USB D0+

4 GND

5 USB V1

6 USB D1-

7 USB D1+

8 GND

2

1

1 – Green LED

(LAN Link LED)

2 – Yellow LED

(LAN Active LED)

1 2

3 4

5

6 7

8

PS/2 Keyboard & PS/2 Mouse Connector

PS/2 Mouse/ Keyboard

Pin No. Definition

1 Data

2 NC

3 GND

4 VCC(+5V)

5 Clock

6 NC

PS/2 Keyboard

PS/2 Mouse

1

2

3

4

5

6

6CX7 Motherboard

11

J1: CPU Cooling FAN Power Connector

Pin No. Definition

1 GND

2 +12V

3 SENSE

1

J17: Power Cooling FAN Power Connector

Pin No. Definition

1 GND

2 +12V

3 SENSE

1

Page is loading ...

Gigabyte 6CX7 Series, GA-6CX7, GA-6CX7-1 User manual

Related papers

Other documents