Whirlpool KEBS147D Installation guide

Whirlpool
Brand
Whirlpool
Model
KEBS147D
Category
Ovens
Type
Installation guide
Trim Kit
Bottom Duct (1)
Side Duct (1)
1” Screws
(4 Req’d 2 Extra)
1/2” Screws
(15 Req’d 2 Extra)
Anti-Tip
Bracket (2)
Bottom
Bracket (2)
Upper Duct (1)
Template (1)
CUTOUT DIMENSIONS
Height
3" Min.
Width
Depth
BUILT-IN TRIM KIT INSTALLATION INSTRUCTION
(KEEP FOR FURTHER REFERENCE)
FOR WHIRLPOOL TRIM-KIT MODELS: MK1134XH, MK1137XH, MK1130XH
• FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS :
(Y)MT1130SG, (Y)MT1135SG, (Y)KCMS135G, (Y)KCMS135H, (Y)MT3130SH,
(Y)MT3135SH, MT2140SJ, (Y)MT2145SJ, MT0130SJ, (Y)KCMS145J
•
UL AND CSA LISTED - FOR USE OVER ELECTRIC HEAT SOURCE
(INCLUDING MODELS - 24”: RBS245PD, KEBI141D, KEBS147D
- 27”: (Y)RBS275PD, (Y)GBS277PD, KEBI171D, (Y)KEBS177D
- 30”: (Y)RBS305PD, GBS307PD, (Y)KEBI101D, (Y)KEBS107D)
PARTS LIST
P/NO.: 3828W5U0076/8172217
Height
Width
Depth
15
3
/4 “
24 ” 27 ” 30 ”
18
1
/2 ”(min.)
with flush mount receptacle.
(
19 ” if non-flush receptacle is used)
22
1
/2 ” 22
1
/2 ”(min.), 25
1
/2 ”(max.) 25
1
/2 ”(min.), 28
1
/2 ”(max.)
STEP 1
1. Disconnect the microwave oven before
proceeding with installation.
2. Remove any loose items inside the microwave
oven.
3. Fasten the bottom brackets to the bottom duct
by using eight 1/2” screws.
4. Remove two existing screws from the right and
left side of microwave cabinet.
(1 screw each side)
5. Install the bottom duct with one existing screw
to the right side of microwave oven as shown.
1
/2" Screws (8)
REAR
FRONT
Existing
Screw (1)
FRONT VIEW OF
MICROWAVE
WARNING
Electrical Shock Hazard
Disconnect power before installing trim kit.
Replace all panels before operating.
Failure to do so can result in death or electrical shock.
STEP 2
1. Connect the side duct to upper duct as shown.
a) Insert projecting tabs of upper duct into holes of side duct.
b) Bend tabs up as shown.
NOTE: Remove any oil or dirt on surface of microwave oven before ducts are attached.
2. Peel off the backing of double sided tape. Using
the left side screw holes as a guide, attach the side
duct and upper duct assembly on the microwave
cabinet. Press down firmly on ducts. Fasten side
duct and bottom duct assembly to left side of
cabinet with one existing screw.
Upper Duct
3 tabs
Side Duct
3 Holes
"a)"
"b)"
Existing 
screw (1)
STEP 4
1. Slide microwave oven part way into cabinet
opening.
(Bottom brackets must be flat to the cutout
floor to engage correctly with anti-tip brackets
as shown)
2. Plug in the microwave oven.
3. Center the microwave oven within the
cut-out opening and slide the microwave oven
in place, engaging the anti-tip brackets.
(Ensure the microwave oven is accurately
centered)
4. Drill pilot holes (use 7/64” drill or #35 drill)
through the positioning flange and then install
three 1/2” screws at the front of the bottom
duct as shown.
Bottom Duct
Anti-Tip
Bracket
Bottom Bracket
1
/2" Screw
Anti-Tip Assembly
Positioning
Flange
Cutout
Opening
1
/2" Screw
STEP 3
1. On the cutout floor, mark hole centers for the
anti-tip brackets as shown using the supplied
template. Be sure to align the center line of
template to center line of cutout floor.
2. Drill four holes for anti-tip brackets.
(use 7/64” drill or #35 drill)
3. Install two anti-tip brackets onto cutout floor
using four 1/2” screws.
DIMENSIONS:
A = 7
5
/16 ”
B = 3 ”
C = 16
5
/16”
A
A
B
B
C
Cutout Floor
Center Line
Anti-Tip Bracket
1
/2" Screws (2)
Anti-Tip Bracket
1
/2" Screws (2)
STEP 5
1. Place the trim kit frame over the microwave oven.
Important Note : Trim kit frame orientation is
important. Orient the frame so that
louvers are sloping downward
to the front. (See Figure Detail A).
2. Make sure the trim kit is level and centered
with respect to microwave oven. Mark four
hole centers through the four mounting
holes of the trim kit.
NOTE: Center the trim kit frame equally
on all four sides.
3. Remove the trim kit and drill four pilot holes.
(use
7
/64” drill or #35 drill)
4. Attach the trim kit frame by using four 1” screws.
Make sure that the orientation is correct as
stated above.
STEP 6
1. Your trim kit is now fully installed. Replace any
loose items that have been removed from
inside microwave oven.
2. Please keep this installation instruction for
future reference.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Whirlpool KEBS147D Installation guide

Whirlpool
Brand
Whirlpool
Model
KEBS147D
Category
Ovens
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents