Dean Dean Millivolt Gas Fryers CE User manual

Price: $8.00

Service Hotline 1-318-865-1711

819-5894

MAY 2007

Dean Millivolt Gas Fryers (CE)

Installation & Operation Manual

Models SM20, SM35, SM40, SM50, SM60, SM80, SR42, SR52 & SR62

CE ONLY

i

Please read all sections of this manual and retain for future reference.

NOTICE

This appliance is intended for professional use only and is to be operated by qualified

personnel only. A Dean Factory Authorized Service Center (FASC) or other qualified

professional should perform installation, maintenance, and repairs. Installation, maintenance,

or repairs by unqualified personnel may void the manufacturer’s warranty. See Chapter 1 of

this manual for definitions of qualified personnel.

NOTICE

This equipment must be installed in accordance with the appropriate national and local codes of

the country and/or region in which the appliance is installed.

NOTICE

Drawings and photos used in this manual are intended to illustrate operational, cleaning and

technical procedures and may not conform to onsite management operational procedures.

NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS

U.S.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: 1) This device may not cause harmful interference, and 2) This device must accept

any interference received, including interference that may cause undesired operation. While

this device is a verified Class A device, it has been shown to meet Class B limits.

Canada

This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set

out by the ICES-003 standard of the Canadian Department of Communications.

Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A

et B prescrites dans la norme NMB-003 edictee par le Ministre des Communications du Canada.

DANGER

Improper installation, adjustment, maintenance or service, and unauthorized alterations or

modifications can cause property damage, injury, or death. Read the installation, operating and

service instructions thoroughly before installing or servicing this equipment. Only qualified

service personnel may convert this appliance to use a gas other than that for which it was

originally configured. See Chapter 1 of this manual for definition of qualified service personnel.

DANGER

Adequate means must be provided to limit the movement of this appliance without depending

upon the gas line connection. Single fryers equipped with legs must be stabilized by installing

anchor straps. All fryers equipped with casters must be stabilized by installing restraining

chains. If a flexible gas line is used, an additional restraining cable must be connected at all

times when the fryer is in use.

ii

DANGER

The front ledge of the fryer is not a step. Do not stand on the fryer. Serious injury can result

from slips or contact with the hot oil.

CAUTION

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

CAUTION

Instructions to be followed in the event the operator smells gas or otherwise detects a gas leak

must be posted in a prominent location. This information can be obtained from the local gas

company or gas supplier.

DANGER

The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container

at the end of frying operations each day. Some food particles can spontaneously combust if left

soaking in certain shortening material. Additional information can be obtained in the filtration

manual included with the system.

WARNING

No structural material on the fryer should be altered or removed to accommodate placement of

the fryer under a hood. Questions? Call the Dean Service Hotline at 1-800-551-8633.

WARNING

Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal

the joint between the frypot. Banging fry baskets on the strip to dislodge shortening will distort

the strip, adversely affecting its fit. It is designed for a tight fit and should only be removed for

cleaning.

IMPORTANT

Safe and satisfactory operation of Dean equipment depends upon its proper installation.

Installation MUST conform with local codes, or in the absence of local codes, to European

Community (CE) Standards.

NOTICE

The Commonwealth of Massachusetts requires any and all gas products to be installed by a

licensed plumber or pipe fitter.

i

Dean Millivolt Gas Fryers (CE)

Installation & Operation Manual

TABLE OF CONTENTS

Page #

1. INTRODUCTION 1-1

1.1 Applicability and Validity 1-1

1.2 Ordering Parts 1-1

1.3 Service Information 1-1

1.4 Safety Information 1-2

1.5 Service Personnel 1-2

2. IMPORTANT INFORMATION 2-1

2.1 Receiving and Unpacking Equipment 2-1

2.2 General 2-1

2.3 Principles of Operation 2-2

2.4 Rating Plate 2-3

2.5 Pre-Installation 2-3

2.6 Equipment Installed at High Altitudes 2-4

2.7 Air Supply and Ventilation 2-4

2.8 Conversion of Units 2-5

3. INSTALLATION 3-1

3.1 Installing the Fryer 3-1

3.2 Installing Casters and Legs 3-1

3.3 Leveling the Fryer 3-2

3.4 Gas Connections 3-4

3.5 Adjustments/Adaptation to Different Gases 3-8

3.6 Gas Inputs 3-9

3.7 Gas Conversion Procedures 3-11

3.8 Gas Conversion Components 3-13

3.9 Electrical Connections 3-13

ii

Dean Millivolt Gas Fryers (CE)

Installation & Operation Manual

TABLE OF CONTENTS (CONT.)

Page #

4. FRYER OPERATIONS 4-1

4.1 Initial Start-up 4-1

4.2 Boil-Out Procedure 4-3

4.3 Final Preparation 4-5

5........ PREVENTATIVE MAINTENANCE 5-1

5.1 General 5-1

6........ TROUBLESHOOTING 6-1

6.1 General 6-1

6.2 Pilot Burner Malfunctions 6-1

6.3 Main Burner Malfunction 6-2

6.4 Millivolt Wiring Diagram 6-3

6.5 Recommended Spare Parts 6-4

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 1: INTRODUCTION

1-1

1.1 Applicability and Validity

Dean Super Marathon and Super Runner Series gas model families have been approved by the

European Union (EU) for sale and installation in the following EU countries: AT, BE, KE, KD,

ES, FI, FR, GB, IE, IT, LU, NL, NO, PT and SE.

This manual is applicable to and valid for all Dean Super Marathon and Super Runner gas

units sold in English-speaking countries, including those in the European Union. Where

conflicts exist between instructions and information in this manual and local or national codes

of the country in which the equipment is installed, installation and operation shall comply with

those codes.

This appliance is only for professional use and shall be used by qualified personnel as defined

in Section 1.5.

1.2 Ordering Parts

Customers may order parts directly from their local Authorized Parts Distributor. For this address

and phone number, contact your maintenance and repair center or call the factory. The factory

address and phone numbers are on the back cover of this manual.

To speed up your order, the following information is required:

Model Number

Type

Serial Number

Optional Equipment

Item Part Number

Quantity Needed

1.3 Service Information

Call the 1-800-551-8633 or (318) 865-1711 Service Hotline number for the location of your nearest

maintenance and repair center. Always give the model and serial numbers of your fryer.

To assist you more efficiently, the following information will be needed:

Model Number

Type

Serial Number

Optional

Equipment

Nature of Problem

Additional information (i.e. cooking environment, time of day, and other pertinent

information) may be helpful in solving your service problem.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 1: INTRODUCTION

1-2

1.4 Safety Information

Before attempting to operate your unit, read the instructions in this manual thoroughly.

Throughout this manual, you will find notations enclosed in double-bordered boxes similar to the

ones below.

CAUTION boxes contain information about actions or conditions that may cause or result in a

malfunction of your system.

CAUTION

Example of a CAUTION box.

WARNING boxes contain information about actions or conditions that may cause or result in

damage to your system, and which may cause your system to malfunction.

WARNING

Example of a WARNING box.

DANGER boxes contain information about actions or conditions that may cause or result in injury

to personnel, and which may cause damage to your system and/or cause your system to malfunction.

DANGER

Hot cooking oil causes severe burns. Never attempt to move a fryer containing hot

cooking oil or to transfer hot cooking oil from one container to another.

1.5 Service Personnel

1.5.1 Definitions

A. Qualified and/or Authorized Operating Personnel

1. Qualified/authorized operating personnel are those who have carefully read the information

in this manual and have familiarized themselves with the equipment functions, or have had

previous experience with the operation of equipment covered in this manual.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 1: INTRODUCTION

1-3

1.5.1 Definitions (cont.)

B. Qualified Installation Personnel

1. Qualified/authorized personnel are those who have carefully read the information in this

manual and have familiarized themselves with the equipment functions, or who have had

previous experience with the operation of the equipment covered in this manual.

C. Qualified Service Personnel

1. Qualified service personnel are those who are familiar with Dean equipment and have been

authorized by Dean to perform service on Dean equipment. All authorized service

personnel are required to be equipped with a complete set of service parts manuals and stock

a minimum amount of parts for Dean equipment. A list of Dean Factory Authorized Service

Centers (FASCs) was included with the fryer when shipped from the factory. Failure to use

qualified service personnel will void the Dean warranty on your equipment.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 2: IMPORTANT INFORMATION

2-1

2.1 Receiving and Unpacking Equipment

A. Check that the container is upright. Use an outward prying motion - no hammering - to remove

the carton. Unpack the fryer carefully and remove all accessories from the carton. Do not discard

or misplace accessories. They will be needed.

B. After unpacking, immediately check the equipment for visible signs of shipping damage. If

damage has occurred, contact the carrier and file the appropriate freight claims. Do not contact

the factory. Shipping damage responsibility is between the carrier and the dealer.

If your equipment arrives damaged:

1. File claim for damages immediately, regardless of extent of damage.

2. Visible loss or damage: Be sure this is noted on the freight bill or express receipt and is

signed by the person making the delivery.

3. Concealed loss or damage: If damage is unnoticed until equipment is unpacked, notify

freight company or carrier immediately, and file a concealed damage claim. The claim

should be filed within 15 days of date of delivery. Be sure to retain container for inspection.

NOTE: Dean Does Not Assume Responsibility for Damage or Loss Incurred in Transit.

C. Move the fryer to the location of installation and install legs and/or casters as described in

Chapter 3.2.

D. Remove all plastic skin from sides, front, and doors of the fryer(s). Failure to do this prior to

initial fryer operation will make it very difficult to remove later.

2.2 General

Qualified, licensed, and/or authorized installation or service personnel only (as defined in

Section 1.5) should perform the following:

• Installation and service on Dean equipment.

• Conversion of this appliance from one gas type to another.

Failure to use qualified, licensed, and/or authorized installation or service personnel to install,

convert to another gas type or otherwise service this equipment will void the Dean warranty

and may result in damage to the equipment or injury to personnel.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 2: IMPORTANT INFORMATION

2-2

2.2 General (cont.)

Where conflicts exist between instructions and information in this manual and local code or

national codes, or regulations, installation and operation shall comply with the codes or

regulations in force in the country in which the equipment is installed.

DANGER

Building codes prohibit a fryer with its open tank of hot oil/shortening from being installed

beside an open flame of any type, including those of broilers and ranges.

Upon arrival, inspect the fryer carefully for visible or concealed damage. (See Receiving and

Unpacking Equipment in Section 2.7.)

CAUTION

Dean appliances equipped with legs are for stationary installations. Appliances fitted with

legs must be lifted during movement to avoid damage to the appliance and bodily injury.

For moveable installations, optional equipment casters must be used. Questions? Call 1-

800-551-8633

Dean Super Marathon and Super Runner Series gas fryers are energy efficient, tube-style, gas-fired

units. All units are shipped completely assembled with accessories packed inside the frypot. All

units are adjusted, tested and inspected at the factory before shipment. Sizes and input rates of all

models are listed in this manual.

WARNING

The on-site supervisor is responsible for ensuring that operators are made aware of

the inherent dangers of operating a hot-oil fryer/filter system, particularly the

aspects of fryer operation, oil filtration, and draining/cleaning procedures.

2.3 Principles of Operation

The incoming gas flows through orifices and is mixed with air in the burners to create the correct

ratio for proper combustion. The mixture is ignited at the front end of each heat tube by the pilot

light. Internal diffusers slow the flame as it goes through the burner tube. This slower and more

turbulent flame gives much better heat transfer to the walls of the tubes, thereby heating the oil more

efficiently.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 2: IMPORTANT INFORMATION

2-3

2.4 Rating Plate

DANGER

Fryers MUST be connected ONLY to the gas-type identified on the attached rating

plate.

The rating plate can be found on the inside panel of the fryer door. Information on this plate

includes the model and serial numbers, kW/hr (BTU/hr) of the burners, outlet gas pressure in mbars

(inches W.C.), and configuration: natural or propane gas. Rating plate data is essential for proper

unit identification, communicating with the factory or requesting special parts and/or information.

2.5 Pre-Installation

DANGER

No structural material on the fryer should be altered or removed to accommodate

placement of the fryer under a hood. Questions? Call the Frymaster/Dean Service

Hotline at 1-800-551-8633.

DANGER

Do not connect this appliance to the gas supply before reviewing all information in

this chapter.

A. General: Only licensed personnel should install any gas-fired equipment.

1. A manual gas shut-off valve must be installed in the gas supply line ahead of the fryers for

safety and ease of future service.

2. Dean Super Marathon and Super Runner Series gas fryers operate on millivolt, and do not

require an external electric power supply.

B. Clearances: The fryer area must be kept free and clear of all combustibles. This unit is design-

certified for the following installations:

1. Commercial installation only (not for household use).

2. Non-combustible floor installation equipped with factory-supplied 6-inch (15-cm) adjustable

legs or 5-inch (13-cm) casters;

3. Combustible construction with a minimum clearance of 6-inches (15-cm) side and 6-inches

(15-cm) rear, and equipped with factory-supplied 6-inch (15-cm) adjustable legs or 5-inch

(13-cm) casters.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 2: IMPORTANT INFORMATION

2-4

2.5 Pre-Installation (cont.)

C. Installation Standards

1. CE/EXPORT STANDARDS: Fryer installation must conform with local codes, or in the

absence of local codes, to the appropriate national or European Community (CE) standards.

2.6 Equipment Installed at High Altitudes

A. The fryer input rating (kW/hr) is for elevations up to 2,000 feet (610-m). For elevations above

2,000 feet (610-m), the rating should be reduced four-percent for each additional 1,000 feet (305-

m) above sea level.

B. The correct orifices are installed at the factory if the operating altitude is known at the time of the

customer’s order.

2.7 Air Supply and Ventilation

Keep the area around the fryer clear to prevent obstruction of combustion and ventilation airflow.

A. Do not connect this fryer to an exhaust duct.

B. Correct installation and adjustment will ensure adequate airflow to the fryer system.

C. A commercial, heavy-duty fryer must vent its combustion wastes to the outside of the building.

A deep-fat fryer must be installed under a powered exhaust hood, or an exhaust fan must be

provided in the wall above the unit, as exhaust gas temperatures are approximately 427-538°C

(800-1000°F). Check air movement during installation. Strong exhaust fans in the exhaust hood

or in the overall air conditioning system can produce slight air drafts in the room.

D. Do not place the fryer’s flue outlet directly into the plenum of the hood, as it will affect the gas

combustion of the fryer.

E. Never

use the interior of the fryer cabinet for storage or store items on shelving over or behind

the fryer. Exhaust temperatures can exceed 427ºC (800°F) and may damage or melt items stored

in or near the fryer.

F. Adequate distance must be maintained from the flue outlet of the fryer(s) to the lower edge of the

filter bank. Per NFPA Standards No. 96, a minimum of 18-inches (45-cm) should be maintained

between the flue(s) and the lower edge of the exhaust hood filter.

G. Filters and drip troughs should be part of any industrial hood, but consult local codes before

constructing and installing any hood. The duct system, the exhaust hood and the filter bank must

be cleaned on a regular basis and kept free of grease.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 2: IMPORTANT INFORMATION

2-5

2.8 Conversion of Units

Pressure:

1 mbar = 10,2 mm W.C. = 0,4-inch W.C.

20 mbar = 204 mm W.C. = 8-inch W.C.

1-inch W.C. = 25,4 mm W.C. = 2,5 mbar

Heat Input:

1 kW = 3410 BTU/hr

100 BTU/hr = 0,0293 kW

Temperature:

0° Celsius = 32° Fahrenheit

Temperature in degrees Celsius = (Temperature in degrees Fahrenheit (F) – 32) x 0,555

100° Celsius = (212° Fahrenheit – 32) x 0,555

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-1

3.1 Installing the Fryer

A. Initial Installation: If installed with legs, do not push against the fryer’s side to adjust its

position. Use a pallet or lift jack to lift the fryer slightly and place it where it is to be installed.

B. Relocating the Fryer: If relocating a fryer installed with legs, remove all weight from each leg

before moving.

Note: If a leg becomes damaged during movement, contact your service agent for immediate

repair/replacement.

CAUTION

Fryers may not function properly if curb mounted.

DANGER

This fryer may tip and cause personal injury if not secured correctly in a stationary

position. Drain all oil/shortening from fryer before moving. Hot oil will splash and

cause severe burns upon contact.

3.2 Leg and Caster Installation

A. General

1. Install legs and rear rigid casters near where the fryer is to be used, as neither are secure for

long transit. Unit cannot be curb mounted and must be equipped with the legs and casters

provided.

2. When positioning the fryer, gently lower the fryer into position to prevent undue strain to

the legs and internal mounting hardware. Use a pallet or lift jack to lift and position the

fryer if possible. Tilting the fryer may damage the legs.

3. The rigid casters must be installed on the fryer rear channel assembly only.

4. Proceed to Step 3.3, Leveling the Fryer, after legs and rear rigid casters are installed to

ensure the fryer is level before using.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-2

3.2 Leg and Caster Installation (cont.)

B. Leg and Rigid Caster Installation

1. Remove unit from pallet.

2. Carefully raise unit with forklift, pallet jack, or other steady means.

3. Place one lock washer on each hex head screw.

4. Insert hex head screws with lock washers [1/4-20 threads by 19 mm (¾") long] through bolt

holes of leg mounting plates and mount to the front channel. Mount rigid casters to the rear

channel following the same procedure. A locknut has been attached to the topside of the

base mounting plates at the factory to capture the hex head screw as it is screwed in.

5. Tighten the bolts to 5.65 Nm (50 inch-lbs.) torque.

CAUTION

For caster retrofit, the unit must be at room temperature and drained of shortening

before installing the casters.

3.3 Leveling the Fryer

A. Place a carpenter’s spirit level across the top of the fryer and level the unit front to back. If the

fryer is off level side to side, a platform or other surface adjustment is needed; there is no side-

to-side level adjustments on a fryer equipped with caster/leg combinations. (If a fryer is

equipped with legs only, side-to-side level adjustments can be made. If a fryer is equipped with

casters only, no level adjustments to the fryer can be made.). If the fryer is not level, the unit

may not function efficiently, the oil may not drain properly for filtering and in a multi-fryer

battery, it may not match adjacent units.

Legs (Only)

1. Adjust leg height with an adjustable or 27 mm (1-1/16-inch) open-end wrench by turning

the hex bullet on the bottom of the leg.

2. The hex bullet is for minor leg height adjustment only. Do not adjust more than 22 mm.

3. When leveling the unit, the leg body should be held firmly to keep the leg from bending or

rotating while turning the hex bullet foot to the required height.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-3

3.3 Leveling the Fryer (cont.)

Rigid Casters (Only)

1. Install the rigid casters on the fryer rear channel only. Legs must be installed on the front

channel.

2. There are no level adjustments for the rigid casters.

B. If the floor is uneven or has a decided slope, place the fryer on a smooth, level platform.

C. If the fryer is moved, re-level the fryer following the instructions given in Steps 3.3.A-C.

D. An installed fryer must be restrained to prevent tipping, which could splash hot oil. Restraints

can be straps or chains anchored to an immovable object (wall, floor anchor), or be the manner

of installation (installing the fryer in an alcove, battering to other appliances, etc.).

E. Installing Optional Swivel Casters:

1. Install non-locking casters only at the rear of the unit.

2. Locking casters must be installed at the front of the unit. Locking casters allow the fryer to

be "locked" in position for safe operations.

3. Follow the same instructions for leg installations as given above in steps 3.2, B1-5.

1/4-20 x 3/4 Hex Bolt

1/4-20 Hex Head Locknut

Washer

Leg Support Assembly

Front Channel or

Rear Channel

1/4-20 x 3/4 Hex Bolt

Front Channel

or Rear Channel

Front or Rear Leg with

Mounting Plate

Adjust as needed

Front View

Rear Side View

Rear Caster—5" Rigid

Optional Caster-

Rear Only

Front Caster—5" Swivel

w/Brake

Optional Caster-

Front Only

Leg and Caster (Optional) Mounting Installation

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-4

3.3 Leveling the Fryer (cont.)

NOTE: The installation must be inspected after it is complete to ensure it meets the intent of

these instructions. The on-site supervisor and/or operator(s) should be informed that the

appliance is installed with restraints. If restraints are removed to move fryer (cleaning

beneath and behind, relocation, etc.), ensure that they are re-installed when fryer is returned

to its permanently installed position.

CAUTION

The fryer MUST be connected to the gas supply specified on the rating and serial number

plate located on the back of the fryer door.

WARNING

If gas odors are detected, the gas supply MUST be shut off at the main shut-off valve. The

local gas company or FASC should be contacted immediately to rectify the problem.

3.4 Gas Connections

Dean Super Marathon and Super Runner Series gas fryers have obtained CE markings for countries

and gas categories shown below:

Countries

Supply Pressures and Gas

(mbar)

Appliance Categories

G20 20/25

BE Belgium

G31 37

IIE(R)B3P

G20 20 I2E

DE Germany

G31 50 I3P

DK Denmark G20 20 I2H

G20 20

ES Spain

G31 37 and 50

II2H3P

G20/G25 20/25

FR France

G31 37 and 50

II2ESI3P

G20 20

GB Great Britain

G31 37

II2H3P

G20 20

GR Greece

G31 37 and 50

II2H3P

G20 20

IR Ireland

G31 37

II2H3P

IT Italy G20 20 I2H

G20/G25 20/25

LU Luxembourg

G31 50

II2E3P

G25 25

NL The Netherlands

G31 50

II2L3P

G20 20

PT Portugal

G31 37

II2H3P

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-5

3.4 Gas Connections (cont.)

NATIONAL CODE REQUIREMENTS

This equipment is to be installed in compliance with the Basic Plumbing Code of the Building

Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation

Manual of the U.S. Food and Drug Administration.

This equipment is manufactured to use the type of gas specified on the rating plate attached to the

door. Connect equipment stamped "NAT" only to natural gas and that stamped "PRO" only to LP

(Propane) gas.

DANGER

Before connecting new pipe to this appliance the pipe must be blown out thoroughly

to remove all foreign material. Foreign material in the burner and gas controls will

cause improper and dangerous operation.

The gas supply (service) line must be the same size or greater than the fryer inlet line. Dean Super

Marathon and Super Runner gas fryers are equipped with 22 mm male ISO 7.1 inlet. The gas supply

line must be sized to accommodate all gas-fired equipment connected to that gas supply. Consult

local gas companies or suppliers, or your local contractor for minimum supply line requirements.

Supply Line Specifications

The gas supply lines must be sized as indicated in the chart below, based on the total number of

fryers connected to the main gas supply.

Recommended Gas Supply Line Sizes

Gas Types Number of Fryers

1 2 to 3 4 or more (*)

Natural Gas 22 mm 28 mm 35 mm

Propane Gas 15 mm 22 mm 28 mm

(*) When exceeding 6 meters for a configuration of more than four fryers, it is necessary to

provide a 33 mm rigid gas connection.

DANGER

All connections must be sealed with a joint compound suitable for the gas being

used and all connections must be tested with a solution of soapy water before

lighting any pilots.

Never use matches, candles, or any other ignition source to check for leaks. If gas

odors are detected, shut off the gas supply to the appliance at the main shut-off

valve and immediately contact the local gas company or an authorized service

agency for service.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-6

3.4 Gas Connections (cont.)

DANGER

"Dry-firing" your unit will cause damage to the frypot and can cause a fire. Always

ensure that melted shortening, cooking oil or water is in the frypot before firing the

unit.

Rigid Connections

Check any installer-supplied intake pipe(s) visually and clean metal particles or other foreign matter

from the threads before installing into a service line. If the intake pipes are not clear of all foreign

matter, the orifices will clog when gas pressure is applied. When using thread compound on gas

piping, use very small amounts and only on male threads. Use a pipe thread compound that is not

affected by the chemical action of LP gases. DO NOT apply thread compound to the first two pipe

threads – doing so will cause clogging of the burner orifices and control valve.

Manual shut-off valve

This gas service supplier-installed valve must be installed in the gas service line ahead of the fryers

in the gas stream and in a position where it can be reached quickly in the event of an emergency.

Regulating Gas Pressure

The fryer and shut-off valve must be disconnected from the gas supply during any pressure testing of

the system.

External gas regulators are not normally required on this fryer. A safety control valve protects the

fryer against pressure fluctuations. If the incoming pressure is in excess of 3.45 kPa/35 mbar, a

step-down regulator will be required.

DANGER

When pressure-testing incoming gas supply lines, disconnect the fryer from the gas

line if the test pressure is 3,45 kPa (½" PSI, 13,84 inches W.C.) or greater to avoid

damage to the fryer’s gas piping and gas valve(s).

A. Manifold Pressure

: Your local service technician should check the manifold pressure with a

manometer.

1. Check the rating plate for manifold gas pressures. Natural gas units normally require 10

mbar, and propane units normally require 27 mbar gas pressure.

2. Confirm that the arrow forged into the bottom of the regulator body, which indicates gas

flow direction, is pointed downstream towards the fryers. The air vent cap is also part

of the regulator and should not be removed.

DEAN MILLIVOLT GAS FRYERS (CE)

CHAPTER 3: INSTALLATION INSTRUCTIONS

3-7

3.4 Gas Connections (cont.)

3. If a vent line from the gas pressure regulator is used, it should be installed in accordance

with local codes or in the absence of local codes, with the appropriate national or

European Community (CE) standards.

WARNING

Use a diluted soap solution to find potentially dangerous gas leaks when making

new connections.

B. Regulators: Gas regulators can be adjusted in the field, but no adjustments should be made

unless the regulator is out of adjustment, or serious pressure fluctuations are observed.

C. Only qualified service personnel should make adjustments to the regulators.

D. Orifices: The fryer can be configured to operate on any available gas. The correct safety

control valve, appropriate gas orifices, and pilot burner are installed at the factory. While

the valve can be adjusted in the field, only qualified service personnel should make any

adjustments with the proper test equipment.

1. The following color codes indicate the type of gas to be used for each fryer and

associated components.

Gas Type CE Color Code

Natural Blue

Propane Red

E. Flexible Couplings, Connectors and Casters

1. If the fryer is to be installed with flexible couplings and/or quick-disconnect fittings, the

installer must use a heavy-duty certified commercial flexible connector of at least 22 mm

NPT (with suitable strain-relief attachments), in compliance with local codes or in the

absence of local codes, with the appropriate national or European Community (CE)

standards. Quick-disconnect devices must comply with local codes or in the absence of

local codes, with the appropriate national or European Community (CE) standards.

2. For an appliance equipped with casters, the installation shall be made with a connector

that complies with local codes or in the absence of local codes, with the appropriate

national or European Community (CE) standards.

3. Under no circumstances are the connector and the quick-disconnect device, or its

associated piping to be used to limit fryer movement. A restraining bracket is provided on

the appliance back to prevent the unit from moving from its installed position.

Page is loading ...

Dean Dean Millivolt Gas Fryers CE User manual

Related papers

Other documents