Black Box LPJ001A-F User manual

Black Box
Brand
Black Box
Model
LPJ001A-F
Type
User manual

This manual is also suitable for

Black Box LPJ001A-F is a high-powered Gigabit power injector that exceeds the IEEE 802.3af power standard. It provides up to 19.6W of power and can be used with IP telephones, wireless access points, IP print servers, IP cameras, and Bluetooth access points. The injector has three LED indicators that diagnose the connection: ON, CONNECT, and FAULT. It also has metal feet that can be affixed to a flat surface for mounting.

Here are some of the features and benefits of the Black Box LPJ001A-F:

  • High power output: Provides up to 19.6W of power, which is more than the 15.4W provided by the 802.3af standard.

Black Box LPJ001A-F is a high-powered Gigabit power injector that exceeds the IEEE 802.3af power standard. It provides up to 19.6W of power and can be used with IP telephones, wireless access points, IP print servers, IP cameras, and Bluetooth access points. The injector has three LED indicators that diagnose the connection: ON, CONNECT, and FAULT. It also has metal feet that can be affixed to a flat surface for mounting.

Here are some of the features and benefits of the Black Box LPJ001A-F:

  • High power output: Provides up to 19.6W of power, which is more than the 15.4W provided by the 802.3af standard.
Exceeds the 802.3af standard.
Use with IP telephones, wireless access
points, IP print servers, IP cameras,
and Bluetooth
®
access points.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) •
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 •
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 •
Web site: www.blackbox.com • E-mail: [email protected]
Customer
Support
Information
BL A C K B O X
®
LPJ001A-F
802.3af PoE Gigabit Injector, 1-Port
1. Specifications
Compliance: cUL/UL
®
; RoHS
Load (Maximum): 0.35 A
Regulation: Line and Load: 54–57 VDC under all
conditions
Connectors: Data in: (1) RJ-45 (10/100/1000);
Data/PoE out: (1) RJ-45 (10/100/1000);
Power: (1) IEC 320 (3-pin)
Indicators: (3) LEDs: (1) ON, (1) CONNECT, (1) FAULT
Power: AC input voltage range: 90–264 VAC;
AC input voltage rating: 100–240 VAC, 47–63 Hz;
Output: 19.6 W at 56 VDC
Size: 1.4"H x 2.6"W x 5.5"D (1 x 6.6 x 14 cm)
Weight: 0.4 lb. (0.2 kg)
2. Overview
The LPJ001A-F is a high-powered Gigabit power injector
that exceeds the IEEE 802.3af power standard. The injector provides
up to 19.6 W of power.
Use the LPJ001A-F with IP telephones, wireless access points, IP print
servers, IP cameras, and Bluetooth access points.
3. Setting Up Your Power Injector
NOTE: Use CAT5e or higher Ethernet cables (not included).
1. Using screws, affix the metal feet on the front and/or rear to a
flat surface such as a table or wall. See Figure 1.
NOTE: The power injector should not use the weight
of the Ethernet cables for support.
Figure 1. Location of metal feet on the power injector.
Power and Data in
data out
Front panel.
IEC-320 power connector.
Back panel.
Figure 2. Ports on the power injector.
2. Connect the 3-pin IEC320 AC input connector to a
power source. Power on the injector.
3. Using CAT5e or higher cable, connect the RJ-45 port
on the injector labeled “IN” to your network switch.
See Figures 2 and 3.
4. Connect the RJ-45 port labeled “OUT” on the injector over
Ethernet cable to the powered device. See Figures 2 and 3.
5. The LEDs will light to diagnose the connection. See Tables 1
and 2.
Figure 3. Cable connections to the power injector.
Insert a screw to
secure the unit
to a surface
Insert a screw
to secure the unit
to a surface
4. Description of LED Functions
Table 1. LEDs and their functions.
LED State Function Description
ON, CONNECT, All three LEDS light Power up Upon power-up, all three LEDs will light for two seconds, as
FAULT LEDs part of the self-test for the internal microprocessor software.
ON LED Lights green after DC output After two seconds, the ON LED will light green, indicating that
two seconds voltage available the DC output voltage is available for powering an 802.3af
PoE compliant load.
CONNECT Lights green 802.3af load This green LED lights when a compliant load is attached to
LED is attached the output RJ-45 connector.
Blinking 802.3af load If the load does not comply with 802.3af PoE standards,
is not attached then the LEDs will blink a code indicating that the load was not
detected. See Table 2 for code descriptions.
FAULT LED Lights red Overload or If a fault, such as an overload or short circuit, occurs, then the
short circuit red FAULT LED lights. See Table 2 for code descriptions.
Lights red for Power supply is The red LED will light for two seconds and then go off as the
two seconds, trying to re-detect power supply tries to re-detect a valid load. If a compliant
then goes off a valid load 802.3af PoE load is NOT detected, the LED will indicate the problem
as described in Table 2.
Table 2. Failure detection codes.
Code Name Description
1 Incorrect resistive signature The green CONNECT and red FAULT LEDs blink three times.
2 Incorrect capacitive signature The green ON LED blinks three times.
3 Incorrect V offset The green CONNECT and green ON LEDs blink three times.
4 Unstable current measurement The green ON LED blinks three times.
5 Low voltage sensed during detection (overload) The red FAULT LED blinks three times.
NOTE: After the LEDs blink three times, the power injector will continue to try to detect a valid load. Until the correct load is applied, the LEDs
will continue to blink. If an open circuit is connected to the output RJ-45 connector, then the LEDs will not blink but the power injector will
continue to try to detect a valid load.
FREE, live, 24/7 Tech Support is just 20 seconds away.
724-746-5500 | blackbox.com
Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc.
Bluetooth is a registered trademark of The Bluetooth SIG, Inc.Any other trademarks
mentioned in this manual are acknowleged to be the property of the trademark owners.
BL A C K B O X
®
©
Copyright 2011. All rights reserved.
Figure 3. Cable connections to the power injector.
LPJ001A-F, version 2
  • Page 1 1
  • Page 2 2

Black Box LPJ001A-F User manual

Black Box
Brand
Black Box
Model
LPJ001A-F
Type
User manual
This manual is also suitable for

Black Box LPJ001A-F is a high-powered Gigabit power injector that exceeds the IEEE 802.3af power standard. It provides up to 19.6W of power and can be used with IP telephones, wireless access points, IP print servers, IP cameras, and Bluetooth access points. The injector has three LED indicators that diagnose the connection: ON, CONNECT, and FAULT. It also has metal feet that can be affixed to a flat surface for mounting.

Here are some of the features and benefits of the Black Box LPJ001A-F:

  • High power output: Provides up to 19.6W of power, which is more than the 15.4W provided by the 802.3af standard.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents