Raymarine Ray 106 Specification

Owner's Handbook

VHF Radio

Ray215e

RAY215E

Modular

VHF Radio

Owner’s

Handbook

Document number: R49018_2

Date: April 2002

i

Purpose

This handbook contains very important information on the installation,

operation, and maintenance of your new equipment. To get the best results

in operation and performance, please take the time to read this handbook

thoroughly.

RAY215E

The RAY215E is a VHF radiotelephone that, when outfitted with the

optional Full Function Handset, includes equipment for Class “D” Digital

Selective Calling. It is intended for general communication within the

Maritime Mobile Service worldwide and is for use on non-SOLAS vessels.

LicenseLicense

License

Regulations in some areas require that you obtain an operator license before

operating VHF radio equipment. It is your responsibility to determine

whether a license is required in your area before operating this equipment.

Maritime Mobile Service Identity (MMSI)Maritime Mobile Service Identity (MMSI)

Maritime Mobile Service Identity (MMSI)

If outfitted with the optional Full Function Handset, the RAY215E includes

equipment for Class “D” Digital Selective Calling (DSC). An MMSI

number is required to operate the DSC features. In some areas, a radio

operator license is required before an MMSI number will be issued. You

can request an MMSI number from the same agency that issues radio

operator licenses in your area. You can then program the MMSI number

into your RAY215E using the operation described in this handbook. If

regulations in your area do not permit you to program the MMSI number

yourself, your Raymarine dealer can program the number for you.

Automatic Automatic

Automatic

TT

T

ransmission Identification System (Aransmission Identification System (A

ransmission Identification System (A

TIS)TIS)

TIS)

If needed, your RAY215E can activate the Automatic Transmission

Identification System (ATIS) feature for use in the inland waterways of

European countries that require automatic identification transmission. An

ATIS ID number is required to operate the ATIS feature. You can request

an ATIS ID number from the same agency that issues radio operator

licenses in your area. You can then program the ATIS number into your

RAY215E using the operation described in this handbook. If regulations

in your area do not permit you to program the ATIS number yourself, you

can have your authorized Raymarine dealer program the number for you.

If outfitted with the optional Full Function Handset, the RAY215E is

fully Class “D” DSC compliant and therefore may, by regulation, disable

ATIS when it is not required.

ii

If your RAY215E does not have an optional Full Function Handset, the

radio is not Class “D” and is therefore prevented by regulation from

disabling the ATIS feature after it has been activated.

SAFETY NOTICE

This device is only an aid to navigation. Its performance can be affected

by many factors including equipment failure or defects, environmental

conditions, and improper handling or use. It is the user's responsibility to

exercise common prudence and navigational judgement, and this device

should not be relied upon as a substitute for such prudence and judgement.

Your Raymarine VHF radio generates and radiates radio frequency (RF)

electromagnetic energy (EME). This equipment must be installed and

operated in accordance with the instructions contained in this handbook.

Failure to do so can result in personal injury and/or product malfunction.

Antenna Mounting and EME ExposureAntenna Mounting and EME Exposure

Antenna Mounting and EME Exposure

For optimal radio performance and minimal human exposure to radio

frequency electromagnetic energy, make sure the antenna is:

• connected to the radio before transmitting

• properly mounted

• located where it will be away from people

• located at least three feet (91cm) from the RAY215E and the microphone/

handset

Adjustments or RepairAdjustments or Repair

Adjustments or Repair

Adjustments require specialized service procedures and tools only

available to qualified service technicians – there are no user serviceable

parts or adjustments. The operator should never remove the cover or

attempt to service the equipment.

Raymarine products are supported by a network of Authorized Service

Representatives. For product information you may contact the following

regional centers:

Europe Raymarine Ltd

Anchorage Park

Portsmouth, Hampshire

England PO3 5TD

Telephone: +44 (0) 23 9269 3611

Fax: +44 (0) 23 9269 4642

iii

United States Raymarine, Inc.

22 Cotton Road, Unit D

Nashua, NH 03063-4219

USA

Telephone: 603-881-5200

800-539-5539

Fax: 603-864-4756

iv

Certificate No.

RT015

We Raymarine Limited Anchorage Park

Portsmouth

Hampshire

England P03 5TD

declare, under our sole responsibility, that the products identified in this declaration, and to which this

declaration relates, are in conformity with the essential requirements of European Parliament and Council

Directive:

1999/5/EC on radio equipment and telecommunication terminal equipment and the mutual

recognition of their conformity.

Product Name: Raymarine RAY 215E VHF Radio

with optional Class "D" DSC

Product Number(s): E43004

Product Option: Full Function Handset (DSC enabled)

Product Number(s): E46020

E46022 (includes second station kit)

The products have been assessed to Conformity Procedure Annex IV of the Directive and by application of the

following standard(s):

EMC EN 60945 : 1997

Safety EN 60945 : 1997

Technical characteristics EN 300 162 Part 2

EN 301 025 Part 2 and Part 3

EN 300 698 Part 2 and Part 3

The assessment is consistent with a Technical Construction File showing conformity with the essential

requirements of the Directive and has been reviewed by Notified Body No. 0191.

The product is labelled with the CE conformity marking, the identification number of the Notified Body and

class identifier.

Signatory: Name Adil Abbas

Title EMC Manager

Company Name Raymarine Limited

Company Address Anchorage Park

Portsmouth, Hampshire

England PO3 5TD

Signature ________________________

Date 07 February 2002

v

Table of Contents

Section 1 General Description

1.1 Introduction ......................................................................... 1-1

1.2 Equipment Features ............................................................. 1-1

1.3 Minimum Function Handset /

Full Function Handset Options............................................ 1-2

Section 2 Installation

2.1 Unpacking and Inspection ................................................... 2-1

2.2 Equipment Supplied............................................................. 2-1

2.2.1 Optional Accessories.............................................. 2-1

2.3 Planning the Installation ...................................................... 2-2

2.3.1 Typical Mounting Methods .................................... 2-2

2.3.2 Flush Mounting ...................................................... 2-3

2.4 Electrical Connections ......................................................... 2-6

2.4.1 DC Power and External Speaker Connections ...... 2-6

2.4.2 External Speaker Connections ............................... 2-7

2.4.3 NMEA Data ........................................................... 2-8

2.4.4 Antenna Connections ............................................. 2-8

2.4.5 Antenna Mounting Suggestions............................. 2-9

2.4.6 Grounding .............................................................. 2-9

Section 3 Operation with Minimum Function Handset

3.1 Introduction ......................................................................... 3-1

3.1.1 DSC and NMEA Operation ................................... 3-1

3.2

Minimum / Full Function Handset Priority ...........................

3-1

3.3

Handset Connections .............................................................

3-2

3.4 Control and LCD Display .................................................... 3-3

3.4.1 Controls .................................................................. 3-3

3.4.2 LCD Display .......................................................... 3-6

3.5 Operating Procedures .......................................................... 3-8

3.5.1 Turning the Power On............................................ 3-8

3.5.2 Setting the Squelch................................................. 3-8

3.5.3 Setting the Volume ................................................. 3-8

3.5.4 Setting the Power Output ....................................... 3-8

3.5.5 Setting the Channel ................................................ 3-9

3.5.6 Selecting the Private Channel ................................ 3-9

3.5.7 Setting the Frequency Mode ................................ 3-10

3.5.8 Transmitting ......................................................... 3-10

3.5.9 Selecting a Weather Channel ................................3-11

vi

3.5.10 Priority Channel ....................................................3-11

3.5.11 Channel Memory...................................................3-11

3.5.12 Resetting Factory Defaults....................................3-11

3.5.13 Scan Modes .......................................................... 3-12

3.5.14 Monitor Mode ...................................................... 3-13

3.5.15 Multi-Call Operation............................................ 3-14

3.5.16 LCD Backlight Function ...................................... 3-14

3.5.17 NMEA Operation ................................................. 3-15

3.5.18 Digital Selective Calling (DSC).......................... 3-16

3.5.18.1 MMSI Number Setup .................................... 3-17

3.5.18.2 Individual Ship's Call .................................... 3-19

3.5.18.3 All Ships Call ................................................ 3-26

3.5.18.4 Group Call ..................................................... 3-27

3.5.18.5 Distress Call .................................................. 3-28

3.5.18.6 Distress Relay Call ........................................ 3-30

3.5.19 ATIS ID No. Entry ............................................... 3-30

Section 4 Operation with Full Function Handset

4.1 Introduction ......................................................................... 4-1

4.2

Minimum / Full Function Handset Priority ...........................

4-1

4.3 Handset Connections ........................................................... 4-2

4.4 Control and LCD Display .................................................... 4-3

4.4.1 Controls .................................................................. 4-3

4.4.2 LCD Display .......................................................... 4-7

4.5 Radio Functions ................................................................... 4-9

4.6 Operating Procedures ........................................................ 4-10

4.6.1 Setting the Volume ................................................4-11

4.6.2 Setting the Squelch................................................4-11

4.6.3 Using the Function Key ........................................4-11

4.6.4 Setting the Frequency Mode ................................ 4-12

4.6.5 Receiving on the Weather Channels .................... 4-13

4.6.6 Selecting the Channel........................................... 4-13

4.6.7 Selecting the Private Channel .............................. 4-14

4.6.8 Priority Channel ................................................... 4-15

4.6.9 Multi-Call Operation............................................ 4-16

4.6.10 Channel Memory.................................................. 4-16

4.6.11 Setting the Transmission Power Output............... 4-17

4.6.12 Desensitized Reception (Local Mode)................. 4-17

4.6.13 LCD Backlight Function ...................................... 4-17

4.6.14 Intercom Mode ..................................................... 4-18

4.6.15 Scan Mode ........................................................... 4-19

4.6.16 Monitor Mode ...................................................... 4-20

vii

4.6.17 NMEA Operation ................................................. 4-21

4.6.18 Digital Selective Calling (DSC)........................... 4-23

4.6.18.1 Individual Call to Another Ship

(Ship-to-Ship)................................................ 4-23

4.6.18.2 Individual Call to Shore Station

(Ship-to-Shore).............................................. 4-26

4.6.18.3 Receiving an Individual Call......................... 4-29

4.6.18.4 Transmitting a Group Call ............................. 4-30

4.6.18.5 Receiving a Group Call ................................. 4-31

4.6.18.6 Transmitting an All Ships Call ...................... 4-32

4.6.18.7 Receiving an All Ships Call .......................... 4-33

4.6.18.8 Transmitting a Distress Call .......................... 4-33

4.6.18.9 Receiving a Distress Call .............................. 4-37

4.6.18.10 Receiving a Distress Relay Call .................... 4-38

4.6.18.11 Using the DSC Log ....................................... 4-39

4.6.19 ATIS Operation .................................................... 4-40

4.7 Menu Operation ................................................................. 4-40

4.7.1 Selecting the Menu Operation ............................. 4-40

4.7.2 NAVSTAT Operation ........................................... 4-41

4.7.3 DSC Operation..................................................... 4-42

4.7.3.1 Selecting Distress Call Type (NATURE) ...... 4-43

4.7.3.2 Manual Entry of Latitude/Longitude

(L/L ENT)...................................................... 4-44

4.7.3.3 Modifying the MMSI Number List

(PHNBOOK)................................................. 4-46

4.7.3.4 Modifying the MMSI Group Number

(GROUP)....................................................... 4-51

4.7.4 Setting Operation ................................................. 4-53

4.7.4.1 Setting ATIS ID Number ............................... 4-53

4.7.4.2 Setting MMSI Number.................................. 4-56

4.7.4.3 ATIS Set Up .................................................. 4-59

Section 5 Maintenance

5.1 How to Contact Raymarine.................................................. 5-1

5.2 Preventive Maintenance....................................................... 5-3

5.3 Specifications....................................................................... 5-3

5.4 Drawings.............................................................................. 5-7

Section 6 Appendix

6.1 International Channel Frequency Tables ............................. 6-1

6.2 US Channel Frequency Tables (Optional) ........................... 6-4

6.2.1 Weather Channels and Frequencies (Optional) ..... 6-6

viii

GLOSSARY OF TERMS

All Scan .......................... Scans all channels

ATIS................................ Automatic Transmission Identification

System. Used for inland waterways in some

European countries.

Canadian Channels ......... Channel designator as defined by Industry

Canada

DSC ................................ Digital Selective Calling

Dual Watch ..................... Monitor the Priority Channel (9 or 16) while

working on another channel

Duplex ............................ Transmit and receive on different frequencies

FCC ................................ Federal Communications Commission

FM .................................. Frequency Modulation

International Channels.... Channel designator as defined by the ITU

ITU ................................. International Telecommunications Union

LCD ................................ Liquid Crystal Display

Memory Scan.................. Scans only user selected memory channels

MMSI ............................. Maritime Mobile Service Identity; a number

issued by each country to identify maritime

stations.

NOAA ............................ National Oceanographic and Atmospheric

Administration

PTT switch...................... Microphone push-to-talk switch

RF ................................... Radio Frequency

RTCM ............................. Radio Technical Commission for Maritime

Services

RX .................................. Receiver

Simplex........................... Transmit and receive on the same frequency

Squelch ........................... A circuit that sets the threshold for cutting off

the receiver when the signal is too weak for

reception of anything but noise

TX................................... Transmit

Tri-Watch ........................ Monitor the Priority Channel and Weather

Channels while working on another channel

US Channels ................... Channel designations as defined by the FCC

VCO................................ Voltage Controlled Oscillator

VHF ................................ Very High Frequency 30MHz to 300MHz

Weather Channels ........... Channels for routine and emergency weather

information broadcast by NOAA

1-1

General Description

Section 1 General Description

1.1 Introduction

Congratulations on your purchase of Raymarine's RAY215E marine

radiotelephone. This handbook describes the physical and functional

characteristics of the radiotelephone.

The RAY215E is a microprocessor-controlled, digitally synthesized,

compact transceiver that provides reliable simplex and semi-duplex (two-

frequency) communications. The RAY215E provides two-way

communications on Marine channels and up to 10 private channels.

The RAY215E can transmit and receive on all available International

marine VHF radiotelephone channels. With a software upgrade, the

RAY215E can also communicate on the US channel set. Refer to the of

Frequency Tables in Section 6, which list all marine VHF channels

available in your RAY215E. You should familiarize yourself with these

tables to ensure proper channel usage.

1.2 Equipment Features

The RAY215E is designed and manufactured to provide ease of operation

with excellent reliability. The important built-in features of the equipment

are listed below.

• Exclusive circuit that automatically selects Channel 16 when the radio

is turned on

• Dedicated key for switching to Channel 16 when using another channel

• Waterproof to CFR-46 standard for Base Station

• Waterproof to JIS-7 standard for Minimum Function Handset and

Optional Full Function Handset

• Full Class “D” DSC functionality (when using optional Full Function

Handset)

• Dedicated DISTRESS key on back of handset, with spring loaded

protective cover (DSC functions require Full Function Handset)

• All Scan and Memory Scan features

• ATIS operation

• Private Channels (requires license)

• Multi-Call operation

• Dual/Tri-Watch Monitor modes

1-2 General Description

• Intercom operation between Minimum Function Handset and Optional

Full Function Handset (second station)

• Distant/local mode

1.3 Minimum / Full Function Handset Options

The RAY215E can be operated with the standard Minimum Function

Handset, an optional Full Function Handset with additional features, or

both. Operation with both units installed enables intercom capabilities

between the two stations.

The Minimum Function Handset features up/down channel select keys,

Channel 16 selection button, plus a quick access Distress key.

The optional Full Function Handset provides you with all the features of

the Minimum Function Handset plus a full alphanumeric keypad, expanded

LCD display, volume and squelch level controls, and full Class “D” DSC

functions, including: DSC Distress calls, dedicated keys for Individual

and All Ships DSC calls, and expanded ship and shore phonebooks for

making DSC Individual calls.

Note: When a Full Function Handset is NOT installed, the unit is not a

Class “D” DSC radio, and will have only basic functionality. You will

not have access to DSC functions or NMEA (GPS) position data

operation. If ATIS is enabled, it will be active all the time – you will not

be able to disable it.

The Single Station Full Function Handset with cradle (Raymarine part

number E46020) is used in lieu of the Minimum Function Handset. The

Dual Station Full Function Handset (Raymarine part number E46022),

which includes a cradle and external speaker, is used in conjunction with

the Minimum Function Handset to enable intercom communications

between the two stations.

Note: The RAY215E is designed to have the base station as the priority

unit. Therefore, Raymarine recommends installing the base station in the

radio operating room or the location from which the ship is normally

navigated. If an optional second station Full Function Handset is also

installed, that handset should be installed in the remote location.

Section 3 describes using the RAY215E with the Minimum Function

Handset. See Section 4 for a complete discussion of operation using the

optional Full Function Handset.

2-1

Installation

Section 2 Installation

2.1 Unpacking and Inspection

Use care when unpacking the unit from the shipping carton to prevent

damage to the contents. It is also good practice to save the carton and the

interior packing material in the event you must return the unit to the factory.

2.2 Equipment Supplied

The following is a list of materials supplied with the RAY215E:

DescriptionDescription

Description

PP

P

art Noart No

art No

..

.

RAY215E Radiotelephone E43004

Minimum Function Handset with Cradle E49016

Power/Optional Speaker/NMEA Cable R49017

Mounting Yoke R49011

Yoke Knob R49012

Handbook, RAY215E E49018

Sun Cover R49014

2.2.1 Optional Accessories

The following is a list of options available for the RAY215E:

DescriptionDescription

Description

P P

P

art Noart No

art No

..

.

Single Station: E46020

Full Function Handset with Cradle

Second Station: E46022

Full Function Handset with Cradle

7 meter Handset Extension Cable

External Powered Handset Speaker

Handset/Microphone Relocation Kit E46026

5m Extension Cable, Full Function Handset E46018

10m Extension Cable, Full Function Handset E46017

3m Extension Cable, External Speaker E46015

External 10W Speaker E46006

Flush Mounting Kit E46023

8' Fiberglass VHF Antenna M51118E

2-2 Installation

2.3 Planning the Installation

When planning the installation of your RAY215E, consider the following

conditions to ensure dependable and trouble-free operation. Mount the

Base Station Transceiver using the Mounting Template provided. The Base

Station Transceiver should be located in the radio telegraph operating

room or the room from which the ship is normally navigated.

The Base Station Transceiver is designed to be mounted horizontally or

vertically on a flat bulkhead. Select a location that is non-metallic, dry,

protected, well-ventilated, and free from high operating temperatures and

excessive vibration. Provide sufficient space behind the transceiver to

allow for proper cable connections to the rear panel connectors. Locate

the transceiver as near as possible to the power source yet as far apart as

possible from any devices that may cause interference such as motors,

generators, and other on board electronics. The transceiver should be

protected from prolonged direct exposure to rain and salt spray.

The transceiver is NOT designed to be mounted in engine compartments.

Do NOT install the transceiver in a location where there may be flammable

vapors (such as in an engine room or compartment, or in a fuel tank bay),

water splash or spray from bilges or hatches, where it is at risk from physical

damage from heavy items (such as hatch covers, tool boxes, etc.), or where

it might be covered by other equipment. Locate the Base Station

Transceiver and Handset at least 1 meter from the antenna.

Safe Compass Distance is 1 meter for a common mechanical compass;

other compass types may require greater distances. To be sure, you should

locate the radio as far as possible from the compass. Test your compass to

verify proper operation while the radio is also operating.

Mount the base station transceiver to allow easy access from the location

where the ship is normally navigated.

2.3.1 Typical Mounting Methods

The RAY215E can be conveniently mounted on a chart table, bulkhead,

overhead, or any other desired location. Refer to Figure 2-1 for typical

mounting methods.

CAUTION

Make sure there are no hidden electrical wires or other items behind

the desired location before proceeding. Check that free access for

mounting and cabling is available.

2-3

Installation

Figure 2-1 Typical Mounting Methods

2.3.2 Flush Mounting

In addition to the typical Mounting Methods, the RAY215E may also be

flush mounted using the optional Flush Mount Kit. These kits are available

from your Raymarine dealer or our Customer Service Department.

There are two methods of mounting the radio using the flush mount kit:

from the front or rear of the console. Choose the method that best suits

your console.

1. Select the location for the radio transceiver. A clear, flat area, of

sufficient height having at least 9" of clear depth behind the panel is

required.

CAUTION

Make sure there are no hidden electrical wires or other items behind

the desired location before proceeding. Check that free access for

mounting and cabling is available.

2. Unpack the Flush Mount kit and confirm that all hardware is present.

3. Mark the cutout area using the cutout guide.

4. Drill a pilot hole inside of the cutout guide area.

5. Using an appropriate saw, carefully cut along the cutout line.

6. Remove the yoke knobs and the mounting yoke from the transceiver.

Check that the radio will fit into the cutout area.

Front Mounting

7. Insert the rear of the transceiver through the flush mount bracket such

that the tabs on the bracket point away from the radio’s front bezel.

2-4 Installation

8. Continue to push the bracket onto the transceiver until it is flush with

the front bezel.

9. On each side of the transceiver, insert a screw through the bracket tab

and into the threaded holes from which you removed the yoke knobs.

10.Tighten the screws.

11. It is recommended to run a bead of RTV or similar sealant around the

inside edge of the bracket to avoid water entry behind the console.

12.Insert the radio and attached bracket into the cutout.

13.Install four flat head screws through the four countersunk holes in the

front of the bracket and secure into the console.

14.From behind the console, connect the power/optional speaker and

antenna cables.

Rear Mounting

7. It is recommended to run a bead of RTV or similar sealant around the

inside edge of the bezel to avoid water entry behind the console.

8. Insert the radio into the cutout until the front bezel is flush with the

console.

9. From behind the console, push the flush mount bracket over the rear

of the transceiver such that the tabs on the bracket point away from

the radio’s front bezel.

10.Continue to push the bracket onto the transceiver until it is flush with

the console.

11. On each side of the transceiver, insert a screw through the bracket tab

and into the threaded holes from which you removed the yoke knobs

but do not fully tighten at this time.

12. Install four pan head screws through the four holes in the bracket and

secure the bracket into the console.

13. From the front, make sure the transceiver is still flush with the console.

14. From behind the console, fully tighten the screws that secure the bracket

to the radio’s threaded yoke knob holes.

15.Connect the power/optional speaker and antenna cables.

2-5

Installation

170 (6.69)

106 (4.17)

140 (5.51)

25 (1)

195 (7.68)

223 (8.78)

80 (3.15)

139 (5.47)

9 (0.35)

Figure 2-2 Outline and Mounting Dimensions

All dimensions are shown in millimeters and (inches)

2-6 Installation

Wire ColorWire Color

Wire Color

FunctionFunction

Function

Connects toConnects to

Connects to

RED Power + Ship's 13.6 VDC power

BLACK Power −

YELLOW Speaker + External speaker

GREEN Speaker −

BLUE NMEA + Input from position source (GPS, etc.)

PURPLE NMEA −

The RED (+) power wire contains a 10 amp in-line fuse.

2.4 Electrical Connections

2.4.1 DC Power and External Speaker

Connections

The 6-foot long power cable is a multi-purpose assembly containing three

wire-pairs for connections to DC power, NMEA input, and an optional

speaker. Connections to the 6-pin connector are as follows:

Figure 2-3 Power/External Speaker/NMEA Cable and 6 Pin Connector

In most cases the length of the power cable should be adequate enough to

reach the DC power source. If additional wire length is required, the cable

can be extended by adding more cable as necessary. However, for power

cable runs longer than 15 feet, larger wire diameter size should be used to

prevent voltage line loss.

Your RAY215E should be connected to the nearest primary source of ship's

DC power. A typical source may be a circuit breaker on the power panel or a

fuse block near the unit. When connecting to either of these sources, the

circuit breaker or other in-line fuse should be rated at 10 amps.

2-7

Installation

Figure 2-4 Power Cable Length

It is recommended that lugs be used to connect the power cable to the DC

supply and the lug connections should be both crimped and soldered.

This is very important in order to ensure adequate current draw to the

equipment. Intermittent operation may result if an insufficient connection

is made to the power source. The connection terminal should be clean,

with no sign of corrosion.

The red (+) wire is connected to the positive terminal of the power source.

The black (-) wire is connected to the negative (ground) of the power

source. Should the power connections be inadvertently reversed, the unit

will not power up but no damage will occur. Check the polarity with a

VOM (Voltage/Ohm Meter) and reconnect observing correct polarity. If

the fuse ever needs replacement, be sure to use the same type and rating.

2.4.2 External Speaker Connections

The yellow (+) wire and green (-) wire are used for connecting the

RAY215E to an external speaker (see Figure 2-3), such as Raymarine’s

10W External Speaker (part number E46006).

Four watts of audio output power are provided for an external 4-ohm

speaker. A suitable speaker can be purchased from your local marine dealer.

Connect the yellow (+) wire and green (-) wire to the speaker observing

polarity as it is marked on the speaker. When connected, the external

speaker will function simultaneously with the internal speaker.

CAUTION: DO NOT short the green (-) wire to the yellow (+) wire.

DO NOT short the green (-) wire to the black Power (-) wire.

Page is loading ...

Raymarine Ray 106 Specification

This manual is also suitable for

Raymarine Ray 106 Specification

Related papers

Other documents