Metabo HWA 5500 M Operating instructions

Brand: Metabo

Model: HWA 5500 M

Type: Operating instructions

Metabo HWA 5500 M is a wastewater pump designed for the pumping of waste water containing faeces. It is well-suited for pumping sewage from toilets, urinals, and sinks from the basement and hobby cellar into an elevated wastewater pipe, into a main sewer pipe in the case of backwater, or into a septic tank. The pump can also be used to pump out water from flooded rooms, e.g. cellars that have been flooded due to heavy rainfall. The pump comes equipped with 10 m electric cable with plug and can be immediately connected to a 230 V socket.

115 167 6177 / 2002 - 1.1

Betriebsanleitung. . . . . . . . . . . . . . . . . . . . 4

Operating Instruction . . . . . . . . . . . . . . . . 10

Instructions d'utilisation . . . . . . . . . . . . . . 16

Handleiding . . . . . . . . . . . . . . . . . . . . . . . 23

Manual de uso . . . . . . . . . . . . . . . . . . . . . 29

Betjeningsvejledning . . . . . . . . . . . . . . . . 36

Bruksanvisning . . . . . . . . . . . . . . . . . . . . 42

HWA 3300 K HWA 3300 N

HWA 4000 N

HWA 5500 M

P0014IVZ.fm

D DEUTSCH ENG ENGLISH

KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY

Wir erklären in alleiniger Verantwortlichkeit, daß dieses Produkt mit den folgenden

Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien** Prüfbericht ***

ausstellende Prüfstelle **** Gemessener/ Garantierter Schalleistungspegel*****

We herewith declare in our sole responsibility that this product complies with the

following standards* in accordance with the regulations of the undermentioned

Directives** testreport *** issuing test office ****measured/ guaranteed sound

power level*****

F FRANÇAIS NL NEDERLANDS

DECLARATION DE CONFORMITE CONFORMITEITSVERKLARING

Nous déclarons, sous notre seule responsabilité, que ce produit est en conformité

avec les normes ou documents normatifs suivants* en vertu des dispositions des

directives **Compte-rendu de

revision *** effectué par ****Niveau de puissance acoustique mesuré/ garanti*****

Wij verklaren als enige verantwoordelijke, dat dit product in overeenstemming is

met de volgende normen*

conform de bepalingen van de richtlijnen** keuringsinstantie *** uitgevoerd door

****Gemeten/ Gegarandeerd geluidsnviveau*****

IT ITALIANO ES ESPA

DICHIARAZIONE DI CONFORMITÀ DECLARACION DE CONFORMIDAD

Noi dichiariamo sotto la nostra esclusiva responsabilità che il presente prodotto è

conforme alle seguenti norme* in conformità con le disposizioni delle normative **

verbale di prova *** eseguita da ****Livello di potenza sonora misurato/

garantito*****

Declaramos bajo nuestra exclusiva responsabilidad, que el presente producto

cumple con las siguientes normas* de acuerdo a lo dispuesto en las directrices**

Acta de revisión *** llevada a cabo por ****Nivel de potencia acústica medido/

garantizado*****

PT PORTUGU

S SV SVENSKA

DECLARAÇÃO DE CONFORMIDADE

KRAN OM

VERENSST

MMELSE

Declaramos sob nossa responsabilidade que este produto está de acordo com as

seguintes normas* de acordo com as directrizes dos regulamentos ** Acta de

revisão *** efectuado por ****Nível de potência

acústica medido/ garantido*****

Vi försäkrar på eget ansvar att denna produkt överensstämmer med följande

standarder* enligt bestämmelserna i direktiven**provningsrapport *** genomfört

av ****Uppmätt/ Garanterad ljudnivå*****

FIN SUOMI NO NORGE

VAATIMUKSENMUKAISUUSVAKUUTUS SAMSVARSERKLÆRING

Vakuutamme, että tämä tuote vastaa seuraavia normeja* on direktiivien

määräysten mukainen**tarkastusraportti*** testin suorittaja****Mitattu/ Taattu äänen

tehotaso*****

Vi erklærer under eget ansvar at dette produkt samsvarer med følgende normer*

henhold til bestemmelsene i direktiv**

prøverapport *** utstilt av ****Målt/ Garantert lydeffektnivå*****

DA DANSK POL POLSKI

OVERENSSTEMMELSESATTEST OŚWIADCZENIE O ZGODNOŚCI

Hermed erklærer vi på eget ansvar, at dette produkt stemmer overens ed følgende

standarder* iht bestemmelserne i direktiverne** rapport *** gennemført af ****Målt/

Garanteret lydeffektniveau*****

Oświadczamy z pełną odpowiedzialnością, że niniejszy produkt odpowiada

wymogom następujących norm* według ustaleń wytycznych **sprawozdanie z

kontroli technicznej *** przeprowadzone przez **** Zmierzony/ Gwarantowany

poziom ciśnienia akustycznego*****

EL ΕΛΛHNIKA HU MAGYAR

∆ΗΛΩΣΗ ΑΝΤΙΣΤΟΙΧΕΙΑΣ MEGEGYEZŐSÉGI NYILATKOZAT

∆ηλώνουµε µε ιδία ευθύνη ότι το προϊόν αυτό αντιστοιχεί στις ακόλουθες

προδιαγραφές* σύµφωνα µε τις διατάξεις των οδηγιών** Εκθεση ελεγχου***

πραγµατοποιούµενος από το****Μετρηθείσα/ Εγγυηµένη στάθµη απόδοσης

ήχου*****

Kizárólagos felelősségünk tudatában ezennel igazoljuk, hogy ez a termék

kielégíti az alábbi szabványokban lefektetett követelményeket* megfelel az alábbi

irányelvek előírásainak** Vizsgálati jegyzőkönyv *** a **** Mért/ Garantált

zajszint****'*

* EN 60335-1, EN 60335-2-41, EN 50081-1, EN 61000-3-2, EN 61000-3-3, EN 55014, EN ISO 3744

**89/336/ EWG, 73/23/ EWG, 93/68/ EWG, 2000/14/ EG Annex VI, P<15KW

*** CE-DE 10-143 677

**** DE10 - TÜV Hannover/ Sachsen Anhalt e.V.

Ing. grad. Hans-Joachim Schaller

Leiter Entwicklung und Konstruktion

ELEKTRA BECKUM AG

Daimlerstraße 1

D-49716 Meppen

D -49716 Meppen, 15.05.2002 1001068/ 02

***** L

= 74 dB/1pW - L

WAd

=76 dB/1pW

HWA 3300 K

HAUSWASSERAUTOMAT

D DEUTSCH ENG ENGLISH

KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY

Wir erklären in alleiniger Verantwortlichkeit, daß dieses Produkt mit den folgenden

Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien** Prüfbericht ***

ausstellende Prüfstelle **** Gemessener/ Garantierter Schalleistungspegel*****

We herewith declare in our sole responsibility that this product complies with the

following standards* in accordance with the regulations of the undermentioned

Directives** testreport *** issuing test office ****measured/ guaranteed sound

power level*****

F FRANÇAIS NL NEDERLANDS

DECLARATION DE CONFORMITE CONFORMITEITSVERKLARING

Nous déclarons, sous notre seule responsabilité, que ce produit est en conformité

avec les normes ou documents normatifs suivants* en vertu des dispositions des

directives **Compte-rendu de

revision *** effectué par ****Niveau de puissance acoustique mesuré/ garanti*****

Wij verklaren als enige verantwoordelijke, dat dit product in overeenstemming is

met de volgende normen*

conform de bepalingen van de richtlijnen** keuringsinstantie *** uitgevoerd door

****Gemeten/ Gegarandeerd geluidsnviveau*****

IT ITALIANO ES ESPAÑOL

DICHIARAZIONE DI CONFORMITÀ DECLARACION DE CONFORMIDAD

Noi dichiariamo sotto la nostra esclusiva responsabilità che il presente prodotto è

conforme alle seguenti norme* in conformità con le disposizioni delle normative **

verbale di prova *** eseguita da ****Livello di potenza sonora misurato/

garantito*****

Declaramos bajo nuestra exclusiva responsabilidad, que el presente producto

cumple con las siguientes normas* de acuerdo a lo dispuesto en las directrices**

Acta de revisión *** llevada a cabo por ****Nivel de potencia acústica medido/

garantizado*****

PT PORTUGUÊS SV SVENSKA

DECLARAÇÃO DE CONFORMIDADE

FÖRSÄKRAN OM ÖVERENSSTÄMMELSE

Declaramos sob nossa responsabilidade que este produto está de acordo com as

seguintes normas* de acordo com as directrizes dos regulamentos ** Acta de

revisão *** efectuado por ****Nível de potência

acústica medido/ garantido*****

Vi försäkrar på eget ansvar att denna produkt överensstämmer med följande

standarder* enligt bestämmelserna i direktiven**provningsrapport *** genomfört

av ****Uppmätt/ Garanterad ljudnivå*****

FIN SUOMI NO NORGE

VAATIMUKSENMUKAISUUSVAKUUTUS SAMSVARSERKLÆRING

Vakuutamme, että tämä tuote vastaa seuraavia normeja* on direktiivien

määräysten mukainen**tarkastusraportti*** testin suorittaja****Mitattu/ Taattu äänen

tehotaso*****

Vi erklærer under eget ansvar at dette produkt samsvarer med følgende normer*

henhold til bestemmelsene i direktiv**

prøverapport *** utstilt av ****Målt/ Garantert lydeffektnivå*****

DA DANSK POL POLSKI

OVERENSSTEMMELSESATTEST OŚWIADCZENIE O ZGODNOŚCI

Hermed erklærer vi på eget ansvar, at dette produkt stemmer overens ed følgende

standarder* iht bestemmelserne i direktiverne** rapport *** gennemført af ****Målt/

Garanteret lydeffektniveau*****

Oświadczamy z pełną odpowiedzialnością, że niniejszy produkt odpowiada

wymogom następujących norm* według ustaleń wytycznych **sprawozdanie z

kontroli technicznej *** przeprowadzone przez **** Zmierzony/ Gwarantowany

poziom ciśnienia akustycznego*****

EL ΕΛΛHNIKA HU MAGYAR

∆ΗΛΩΣΗ ΑΝΤΙΣΤΟΙΧΕΙΑΣ MEGEGYEZŐSÉGI NYILATKOZAT

∆ηλώνουµε µε ιδία ευθύνη ότι το προϊόν αυτό αντιστοιχεί στις ακόλουθες

προδιαγραφές* σύµφωνα µε τις διατάξεις των οδηγιών** Εκθεση ελεγχου***

πραγµατοποιούµενος από το****Μετρηθείσα/ Εγγυηµένη στάθµη απόδοσης

ήχου*****

Kizárólagos felelősségünk tudatában ezennel igazoljuk, hogy ez a termék

kielégíti az alábbi szabványokban lefektetett követelményeket* megfelel az

alábbi irányelvek előírásainak** Vizsgálati jegyzőkönyv *** a **** Mért/ Garantált

zajszint****'*

* EN 60335-1, EN 60335-2-41, EN 50081-1, EN 61000-3-2, EN 61000-3-3, EN 55014, EN ISO 3744

**89/336/ EWG, 73/23/ EWG, 93/68/ EWG, 2000/14/ EG Annex VI, P<15KW

*** CE-DE 10-143 677

**** DE10 - TÜV Hannover/ Sachsen Anhalt e.V.

Ing. grad. Hans-Joachim Schaller

Leiter Entwicklung und Konstruktion

ELEKTRA BECKUM AG

Daimlerstraße 1

D-49716 Meppen

D -49716 Meppen, 15.05.2002 1001071/ 02

***** L

= 83 dB/1pW - L

WAd

=90 dB/1pW

HWA 3300 N

HAUSWASSERAUTOMAT

U2P0014.fm

D DEUTSCH ENG ENGLISH

KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY

Wir erklären in alleiniger Verantwortlichkeit, daß dieses Produkt mit den folgenden

Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien** Prüfbericht ***

ausstellende Prüfstelle **** Gemessener/ Garantierter Schalleistungspegel*****

We herewith declare in our sole responsibility that this product complies with the

following standards* in accordance with the regulations of the undermentioned

Directives** testreport *** issuing test office ****measured/ guaranteed sound

power level*****

F FRANÇAIS NL NEDERLANDS

DECLARATION DE CONFORMITE CONFORMITEITSVERKLARING

Nous déclarons, sous notre seule responsabilité, que ce produit est en conformité

avec les normes ou documents normatifs suivants* en vertu des dispositions des

directives **Compte-rendu de

revision *** effectué par ****Niveau de puissance acoustique mesuré/ garanti*****

Wij verklaren als enige verantwoordelijke, dat dit product in overeenstemming is

met de volgende normen*

conform de bepalingen van de richtlijnen** keuringsinstantie *** uitgevoerd door

****Gemeten/ Gegarandeerd geluidsnviveau*****

IT ITALIANO ES ESPA

DICHIARAZIONE DI CONFORMITÀ DECLARACION DE CONFORMIDAD

Noi dichiariamo sotto la nostra esclusiva responsabilità che il presente prodotto è

conforme alle seguenti norme* in conformità con le disposizioni delle normative **

verbale di prova *** eseguita da ****Livello di potenza sonora misurato/

garantito*****

Declaramos bajo nuestra exclusiva responsabilidad, que el presente producto

cumple con las siguientes normas* de acuerdo a lo dispuesto en las directrices**

Acta de revisión *** llevada a cabo por ****Nivel de potencia acústica medido/

garantizado*****

PT PORTUGU

S SV SVENSKA

DECLARAÇÃO DE CONFORMIDADE

KRAN OM

VERENSST

MMELSE

Declaramos sob nossa responsabilidade que este produto está de acordo com as

seguintes normas* de acordo com as directrizes dos regulamentos ** Acta de

revisão *** efectuado por ****Nível de potência

acústica medido/ garantido*****

Vi försäkrar på eget ansvar att denna produkt överensstämmer med följande

standarder* enligt bestämmelserna i direktiven**provningsrapport *** genomfört

av ****Uppmätt/ Garanterad ljudnivå*****

FIN SUOMI NO NORGE

VAATIMUKSENMUKAISUUSVAKUUTUS SAMSVARSERKLÆRING

Vakuutamme, että tämä tuote vastaa seuraavia normeja* on direktiivien

määräysten mukainen**tarkastusraportti*** testin suorittaja****Mitattu/ Taattu äänen

tehotaso*****

Vi erklærer under eget ansvar at dette produkt samsvarer med følgende normer*

henhold til bestemmelsene i direktiv**

prøverapport *** utstilt av ****Målt/ Garantert lydeffektnivå*****

DA DANSK POL POLSKI

OVERENSSTEMMELSESATTEST OŚWIADCZENIE O ZGODNOŚCI

Hermed erklærer vi på eget ansvar, at dette produkt stemmer overens ed følgende

standarder* iht bestemmelserne i direktiverne** rapport *** gennemført af ****Målt/

Garanteret lydeffektniveau*****

Oświadczamy z pełną odpowiedzialnością, że niniejszy produkt odpowiada

wymogom następujących norm* według ustaleń wytycznych **sprawozdanie z

kontroli technicznej *** przeprowadzone przez **** Zmierzony/ Gwarantowany

poziom ciśnienia akustycznego*****

EL ΕΛΛHNIKA HU MAGYAR

∆ΗΛΩΣΗ ΑΝΤΙΣΤΟΙΧΕΙΑΣ MEGEGYEZŐSÉGI NYILATKOZAT

∆ηλώνουµε µε ιδία ευθύνη ότι το προϊόν αυτό αντιστοιχεί στις ακόλουθες

προδιαγραφές* σύµφωνα µε τις διατάξεις των οδηγιών** Εκθεση ελεγχου***

πραγµατοποιούµενος από το****Μετρηθείσα/ Εγγυηµένη στάθµη απόδοσης

ήχου*****

Kizárólagos felelősségünk tudatában ezennel igazoljuk, hogy ez a termék

kielégíti az alábbi szabványokban lefektetett követelményeket* megfelel az alábbi

irányelvek előírásainak** Vizsgálati jegyzőkönyv *** a **** Mért/ Garantált

zajszint****'*

* EN 60335-1, EN 60335-2-41, EN 50081-1, EN 61000-3-2, EN 61000-3-3, EN 55014, EN ISO 3744

**89/336/ EWG, 73/23/ EWG, 93/68/ EWG, 2000/14/ EG Annex VI, P<15KW

*** CE-DE 10-143 677

**** DE10 - TÜV Hannover/ Sachsen Anhalt e.V.

Ing. grad. Hans-Joachim Schaller

Leiter Entwicklung und Konstruktion

ELEKTRA BECKUM AG

Daimlerstraße 1

D-49716 Meppen

D -49716 Meppen, 15.05.2002 1001074/ 02

***** L

= 86 dB/1pW - L

WAd

=89 dB/1pW

HWA 4000 N

HAUSWASSERAUTOMAT

D DEUTSCH ENG ENGLISH

KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY

Wir erklären in alleiniger Verantwortlichkeit, daß dieses Produkt mit den folgenden

Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien** Prüfbericht ***

ausstellende Prüfstelle **** Gemessener/ Garantierter Schalleistungspegel*****

We herewith declare in our sole responsibility that this product complies with the

following standards* in accordance with the regulations of the undermentioned

Directives** testreport *** issuing test office ****measured/ guaranteed sound

power level*****

F FRANÇAIS NL NEDERLANDS

DECLARATION DE CONFORMITE CONFORMITEITSVERKLARING

Nous déclarons, sous notre seule responsabilité, que ce produit est en conformité

avec les normes ou documents normatifs suivants* en vertu des dispositions des

directives **Compte-rendu de

revision *** effectué par ****Niveau de puissance acoustique mesuré/ garanti*****

Wij verklaren als enige verantwoordelijke, dat dit product in overeenstemming is

met de volgende normen*

conform de bepalingen van de richtlijnen** keuringsinstantie *** uitgevoerd door

****Gemeten/ Gegarandeerd geluidsnviveau*****

IT ITALIANO ES ESPA

DICHIARAZIONE DI CONFORMITÀ DECLARACION DE CONFORMIDAD

Noi dichiariamo sotto la nostra esclusiva responsabilità che il presente prodotto è

conforme alle seguenti norme* in conformità con le disposizioni delle normative **

verbale di prova *** eseguita da ****Livello di potenza sonora misurato/

garantito*****

Declaramos bajo nuestra exclusiva responsabilidad, que el presente producto

cumple con las siguientes normas* de acuerdo a lo dispuesto en las directrices**

Acta de revisión *** llevada a cabo por ****Nivel de potencia acústica medido/

garantizado*****

PT PORTUGU

S SV SVENSKA

DECLARAÇÃO DE CONFORMIDADE

KRAN OM

VERENSST

MMELSE

Declaramos sob nossa responsabilidade que este produto está de acordo com as

seguintes normas* de acordo com as directrizes dos regulamentos ** Acta de

revisão *** efectuado por ****Nível de potência

acústica medido/ garantido*****

Vi försäkrar på eget ansvar att denna produkt överensstämmer med följande

standarder* enligt bestämmelserna i direktiven**provningsrapport *** genomfört

av ****Uppmätt/ Garanterad ljudnivå*****

FIN SUOMI NO NORGE

VAATIMUKSENMUKAISUUSVAKUUTUS SAMSVARSERKLÆRING

Vakuutamme, että tämä tuote vastaa seuraavia normeja* on direktiivien

määräysten mukainen**tarkastusraportti*** testin suorittaja****Mitattu/ Taattu äänen

tehotaso*****

Vi erklærer under eget ansvar at dette produkt samsvarer med følgende normer*

henhold til bestemmelsene i direktiv**

prøverapport *** utstilt av ****Målt/ Garantert lydeffektnivå*****

DA DANSK POL POLSKI

OVERENSSTEMMELSESATTEST OŚWIADCZENIE O ZGODNOŚCI

Hermed erklærer vi på eget ansvar, at dette produkt stemmer overens ed følgende

standarder* iht bestemmelserne i direktiverne** rapport *** gennemført af ****Målt/

Garanteret lydeffektniveau*****

Oświadczamy z pełną odpowiedzialnością, że niniejszy produkt odpowiada

wymogom następujących norm* według ustaleń wytycznych **sprawozdanie z

kontroli technicznej *** przeprowadzone przez **** Zmierzony/ Gwarantowany

poziom ciśnienia akustycznego*****

EL ΕΛΛHNIKA HU MAGYAR

∆ΗΛΩΣΗ ΑΝΤΙΣΤΟΙΧΕΙΑΣ MEGEGYEZŐSÉGI NYILATKOZAT

∆ηλώνουµε µε ιδία ευθύνη ότι το προϊόν αυτό αντιστοιχεί στις ακόλουθες

προδιαγραφές* σύµφωνα µε τις διατάξεις των οδηγιών** Εκθεση ελεγχου***

πραγµατοποιούµενος από το****Μετρηθείσα/ Εγγυηµένη στάθµη απόδοσης

ήχου*****

Kizárólagos felelősségünk tudatában ezennel igazoljuk, hogy ez a termék

kielégíti az alábbi szabványokban lefektetett követelményeket* megfelel az alábbi

irányelvek előírásainak** Vizsgálati jegyzőkönyv *** a **** Mért/ Garantált

zajszint****'*

* EN 60335-1, EN 60335-2-41, EN 50081-1, EN 61000-3-2, EN 61000-3-3, EN 55014, EN ISO 3744

**89/336/ EWG, 73/23/ EWG, 93/68/ EWG, 2000/14/ EG Annex VI, P<15KW

*** CE-DE 10-143 677

**** DE10 - TÜV Hannover/ Sachsen Anhalt e.V.

Ing. grad. Hans-Joachim Schaller

Leiter Entwicklung und Konstruktion

ELEKTRA BECKUM AG

Daimlerstraße 1

D-49716 Meppen

D -49716 Meppen, 15.05.2002 1001078/ 02

***** L

= 75 dB/1pW - L

WAd

= 78 dB/1pW

HWA 5500 M

HAUSWASSERAUTOMAT

ENGLISH

1. Machine Overview

1 Discharge port

2 Hydromat hydrostatic pressure

switch

3 Plug, water filler

4 Pump inlet

Caution!

For pumping contaminated

fluids use a suction filter (see

"Available Accessories").

Note:

A check valve is recom-

mended to prevent water backflow

when the pump is switched off.

5 Drain plug

6 Pump

7 Power cable with plug

Operating Instruction ENGLISH

ENGLISH

1. Machine Overview ....................10

2. Please Read First!.....................11

3. Range of Application and

Pumping Media .........................11

4. Safety .........................................11

4.1 Specified conditions of use.........11

4.2 General safety instructions .........11

5. Prior to Operation.....................11

5.1 Hydromat installation ..................11

5.2 Installation...................................12

5.3 Suction line connection...............12

5.4 Discharge hose connection ........12

5.5 Connection to a pipe system ......12

5.6 Mains connection........................12

5.7 Filling the pump and priming.......12

6. Operation...................................12

6.1 Commissioning ...........................12

6.2 Pump characteristic curve ..........13

7. Care and Maintenance..............13

7.1 Periodic maintenance .................13

7.2 Danger of freezing ......................13

7.3 Equipment dismounting and

storing.........................................13

8. Trouble Shooting ......................13

8.1 Fault finding ................................13

8.2 Hydromat adjustment..................14

9. Repairs.......................................14

10. Environmental Protection........14

11. Available Accessories.........14/48

12. Technical Specifications..........15

• Read these instructions before use.

Pay special attention to the safety

instructions.

• Disregard of the operating instruc-

tions invalidates the manufacturer's

warranty; the manufacturer is not

liable for any damages resulting

from such disregard.

• If you notice transport damage while

unpacking, notify your supplier

immediately. Do not operate the

machine!

• Dispose of the packing in an envi-

ronmentally friendly manner. Take

to a proper collecting point.

• Keep these instructions for refer-

ence on any issues you may be

uncertain about.

• If you lend or sell this machine be

sure to have the instructions go with

it.

This equipment is intended for pumping

clear water in domestic and garden

applications, such as

− irrigation,

− well, rain and service water pump-

ing,

− draining of pools, garden ponds and

water tanks.

The max. permissible temperature of the

pumped medium is 50 °C.

4.1 Specified conditions of

use

This equipment must not be used to sup-

ply drinking water or for pumping food-

stuff.

Explosive, flammable or aggressive flu-

ids and substances detrimental to health

must not be pumped.

This equipment is not suitable for com-

mercial or industrial use.

Alteration of the equipment or use of

parts not approved by the equipment

manufacturer is not permitted.

Any inexpert use the equipment is not as

specified; it can cause unforeseen dam-

age!

4.2 General safety instruc-

tions

Children, juveniles and persons not fam-

ilar with the instructions are not permit-

ted to operate the pump.

When used in swimming pools and gar-

den ponds and their range of protection,

the regulations according to DIN VDE

0100 -702, -738 are to be observed.

When used as domestic water supply

any applicable local regulations pertain-

ing to water supply and waste water dis-

posal, plus DIN 1988 (where applicable)

are to be observed.

The following residual risks do principally

exist when operating pumps – they can

not be fully eliminated even by employ-

ing safety devices.

Hazard by ambient conditions!

Do not expose to rain. Do not operate in

damp or wet environment.

Do not direct water jet directly against

the equipment or other electrical parts!

Risk of fatal electric shock!

Do not use the pump in hazardous loca-

tions or near inflammable liquids and

gases!

Danger! Risk of electric shock!

Always unplug before servicing.

Do not touch the plug with wet hands! To

unplug always pull on the plug, not the

power cable.

Do not buckle, squeeze, drag or drive

over power cable and extension cables;

protect from sharp edges.

Danger by pump failings!

Before each use check the equipment,

especially the power cable, plug and

electrical parts for possible damage.

Risk of fatal electric shock!

A damaged pump must be workmanlike

repaired before it can be used again.

Do not attempt to repair the equipment

yourself! Only trained specialists are

permitted to service or repair pumps.

The equipment is easily assembled and

connected.

If in doubt, contact your specialist sup-

plier or qualified electrician.

5.1 Hydromat installation

Note:

The equipment is supplied with

the hydrostatic pressure switch unin-

stalled but fully wired, to prevent trans-

port damage.

Prior to commissioning the hydrostatic

pressure switch must be fitted (illustra-

tion as per version).

1. Check to see that the power cable is

unplugged.

2. Hold hydrostatic pressure switch

housing with one hand to keep the

cable to the pump from twisting.

3. Screw the Hydromat's lower part

onto the pumps discharge port; lift

housing slightly, if necessary.

4. Position Hydromat so that its con-

trols are conveniently reached.

Table of Contents

2. Please Read First!

3. Range of Application and

Pumping Media

4. Safety

5. Prior to Operation

ENGLISH

5.2 Installation

• The equipment must be placed on a

plane and level surface, suitable of

bearing the weight of the equipment

fully filled with water.

• To prevent vibrations, the equip-

ment should not be fastened with

screws but placed onto an elastic

base.

• The installation location should be

well vented and protected from

atmospheric exposure.

• When operated at garden ponds

and pools the equipment must be

set up safe against flooding and pro-

tected from falling into the water.

Any additional legal requirements

are to be observed.

5.3 Suction line connection

Note:

Possibly further accessories may

be required for connection (see "Availa-

ble Accessories").

Caution!

The suction line needs to be

installed in such manner that it does

not exert mechanical force or distor-

tion to the pump.

Caution!

When pumping contaminated

fluids install a suction strainer to pro-

tect the pump from sand and dirt.

Note:

A check valve is recommended to

prevent water backflow when the pump

is switched off.

• All screw fittings need to be sealed

with thread sealing tape; leakage

places cause the priming of air and

reduce or prevent the priming of

water.

• The suction line should have at least

1" (25mm) inner diameter; it must

be non-buckling and vacuum-proof.

• Keep suction line as short as practi-

cal, since with increasing length the

pump capacity is reduced.

• The suction line should raise

towards the pump to prevent air

locks.

• A sufficient water supply must be

ensured, the foot valve at the end of

the suction line must be submerged

in water at all times.

5.4 Discharge hose connec-

tion

Note:

Possibly further accessories may

be required for connection (see "Availa-

ble Accessories").

Caution!

The discharge (or pressure)

line needs to be installed in such

manner that it does not exert mechan-

ical force or distortion to the pump.

• All screw fittings should be sealed

with thread sealing tape to prevent

leakage.

• All parts of the pressure line must be

resistant to internal pressure.

• All parts of the pressure line must be

installed in a workmanlike manner.

Danger!

Improper installation and use

of parts not resistant to internal pres-

sure can cause the pressure line to

break during operation. Risk of per-

sonal injury by liquid spurting from

the line under high pressure!

5.5 Connection to a pipe sys-

tem

A permanent installation (e.g. for indoor

domestic water supply) is also possible.

• To reduce vibrations and noise, the

equipment should be connected to

the piping with elastic hose pipes.

5.6 Mains connection

Danger! Risk of electric shock!

Do not operate the equipment

in wet environment and only under

the following conditions:

• Connect only to an earthed outlet

that is properly installed, earthed

and tested.

• Mains voltage and fuse protection

must correspond to those stated

in the "Technical Specications".

• When operated at pools, garden

ponds and similar locations, the

equipment must be protected by

a residual current operated

device (RCD, 30 mA) (DIN VDE

0100 -702, -738 or equivalent

applicable local regulations).

We recommend the use of RCD's

as a general precaution for per-

sonal protection.

• When operated outdoors the elec-

trical connections must be

splash-proof; they must not be

placed in water.

• Use only extension cables of suf-

ficient lead cross section (see

"Technical Specifications").

Unroll cable reels fully.

5.7 Filling the pump and

priming

Caution!

After installation, loss of water

or priming of air the pump needs to

be filled with water. Starting the pump

without water causes damage!

Note:

The suction line does not need to

be filled, the pump is self-priming. How-

ever, depending on length and diameter

of the suction line it may take some time

until pressure has built up.

1. Remove the water filler plug, com-

plete with gasket.

2. Slowly pour in clear water, until the

pump is filled.

3. To reduce the time needed for prim-

ing you can also fill the suction line.

4. Replace the water filler plug, com-

plete with gasket.

5. Open pressure line (open tap or

spray nozzle) for any air to escape

during priming.

6. Start equipment (see "Operation").

7. Close pressure line when only water

runs out.

Pump and suction line must be con-

nected and filled (see "Prior to Opera-

tion").

Caution!

Pump must not run dry. Ensure

there is always sufficient pumping

medium (water) available.

• If the motor does not start, no pres-

sure is built up or similar effects are

evident, switch the equipment OFF

– and try to remove the fault (see

"Trouble Shooting").

• If the pump should be blocked by a

foreign object or the motor overheat,

the motor protection will switch the

motor off.

6.1 Commissioning

Note:

The Hydromat

− starts the pump when water is

required (with an open discharge

line the water pressure falls below

the cut-in pressure);

− stops the pump approx. 10 sec. after

closing the discharge line (with a

closed discharge line the water

pressure increases);

6. Operation

ENGLISH

− stops the pump if no water is

pumped to prevent it from running

dry (air in suction line).

1. Plug power cable in.

2. Check that the power indicator lamp

(10) is on.

3. Open discharge line.

4. Press the reset button (8). The

pump will start up.

• If no water is pumped after approx.

10 seconds, the Hydromat will stop

the pump. In this case keep the

reset button pressed until water

comes out.

• If not water comes out within

3 minutes, check suction line.

Note:

If the fault indicator lamp (9)

lights up, there is either air in the suction

line or the cut-in pressure too high (see

"Trouble Shooting").

6.2 Pump characteristic

curve

The pump characteristic curve shows

which pump capacity is possible in

dependance on the delivery head.

Pump characteristic curve at 0.5 m suc-

tion head and 1" suction hose – for

model:

A HWA 5500 M

B HWA 4000 N

C HWA 3300 K, HWA 3300 N

Danger!

Prior to all servicing:

− Unplug.

− Ensure that pressure is relieved

from equipment and connected

accessories.

Service and repair work other than

described here must be left to quali-

fied specialists.

7.1 Periodic maintenance

• Check equipment and accessories,

especially electrical parts and parts

under pressure for possible dam-

age; have repaired, if necessary.

• Check suction and pressure lines for

leakages.

• If the pump capacity lessens clean

suction strainer and filter cartridge (if

installed), replace if necessary.

7.2 Danger of freezing

Caution!

Frost damages the pump and

accessories, as both always contain

water!

• When there is danger of freezing,

dismount equipment and accesso-

ries and store at a freeze-proof loca-

tion (see below).

7.3 Equipment dismounting

and storing

1. Unplug.

2. Open pressure line (open tap or

spray nozzle) and drain water com-

pletely.

3. Drain pump completely; to do so

remove the drain plug from the

pump.

4. Disconnect suction and pressure

lines from the equipment.

5. Store equipment in a frost-free

space (at least 5 °C).

Danger!

Prior to all servicing:

− Unplug.

− Ensure that pressure is relieved

from equipment and connected

accessories.

8.1 Fault finding

Pump does not run:

• Hydromat has shut the pump off.

− Press the reset button.

If after approx. 10 seconds no

water is pumped, keep reset but-

ton pressed until water comes

out.

• No mains voltage.

− Check cables, plug, outlet and

mains fuse.

• Mains voltage too low.

− Use only extension cables with

sufficient lead cross section (see

"Technical Specifications").

• Motor overheated, motor protection

relay tripped.

− Start equipment again after

having cooled down (see "Opera-

tion").

− Ensure sufficient ventilation, keep

vent slots clear.

− Observe max. temperature of the

pumped medium.

• Motor hums but does not start.

− With the motor switched OFF, put

screwdriver or similar through the

fan cover's vent slots and turn the

fan.

• Pump blocked or out of order.

− Disassemble pump and clean.

− Clean diffusor, replace if neces-

sary.

− Clean impeller, replace if neces-

sary.

Pump does not prime correctly or

runs very noisily:

• Lack of water.

− Ensure there is a sufficient water

supply.

• Suction line leaky.

− Seal suction line, tighten screw

fittings.

• Suction head too high.

− Observe max. suction head.

− Install check valve, fill suction line

with water.

• Suction strainer (accessory)

blocked.

− Clean, replace if necessary.

• Check valve (accessory) blocked.

− Clean, replace if necessary.

• Water leaks between motor and

pump, Duocone seal worn.

− Replace Duocone seal.

• Pump blocked or out of order.

− see above.

Pressure too low, long pump post-run

or pump keeps starting and stopping:

• Suction line leaky or too much suc-

tion head.

− see above.

8 Reset button

9 Fault indicator lamp (red)

10 Power indicator lamp (green)

5500

/ h

3300 4000

7. Care and Maintenance

8. Trouble Shooting

ENGLISH

• Pump blocked or out of order.

− see above.

• Hydromat incorrectly adjusted, fault

indicator lamp is on.

− Check cut-in pressure, readjust if

necessary.

8.2 Hydromat adjustment

When the cut-in pressure is too high and

the fault indicator lamp (11) is on, the

Hydromat needs to be readjusted.

1. Unplug.

2. Turn the regulating screw (12) as

follows:

− counter-clockwise to decrease

the cut-in pressure;

− clockwise to increase the cut-in

pressure.

3. Start equipment again and check

function (see "Operation").

Danger!

Repairs to electric tools must

only be carried out by a qualified

electrician!

Electric tools in need of repair can be

sent to an authorised service center in

your country. See spare parts list for

address.

Please attach a description of the fault to

the electric tool.

For shipping:

• Drain pump completely (see "Equip-

ment dismounting and storing").

• Dismount Hydromat (to prevent

shipping damage).

• Ship equipment in original packing,

if possible.

The packaging of the pump can be

100 % recycled.

Worn out power tools and accessories

contain considerable amounts of valua-

ble raw and plastic materials, which can

be recycled.

These instructions are printed on chlo-

rine-free bleached paper.

For this equipment the following acces-

sories are available at specialist dealers.

Note:

Illustrations and stock numbers

can be found at the end of these instruc-

tions.

A Pump Installation Package,

complete with double nipple, check

valve, filter short, washable filter

cartridge, spiral hose assembly

1 m, thread sealing tape.

B Hydrostop,

for automatic stopping when there

is a lack of water, prevents the

pump from running dry.

C Dry-running Stop Switch,

with 10 m cable, keeps the pump

from running dry when pumping

from tank, pool, etc.

D Spiral Hose 1"

1) 1 m assembly, with quick

release screw fitting at both

ends;

2) 4 m, complete with quick

release screw fitting and

strainer with foot valve;

3) 7 m, complete with quick

release screw fitting and

strainer with foot valve.

E Filter, 1" connection, short,

complete with washable plastic fil-

ter cartridge.

F Disposable Filter Cartridge, short,

for mechanical preliminary filtering

of sand.

G Washable Filter cartridge, short,

for mechanical preliminary filtering

of sand, reusable.

H Activated Carbon Filter Cartridge,

short,

for use with chlorous water,

removes odours or discolouring.

I Filter Cartridge Poly, short,

filled with polyphosphate, for calcif-

erous water supplied to water heat-

ers.

J Pipe Nipple 150 mm, 1" male at

both ends, galvanized, to connect

pump and filter.

K Double Nipple, 1" male at boths

ends.

L Check Valve 1" female, prevents

water backflow and pump running

dry.

M Thread Sealing Tape, 12 m roll.

9. Repairs

10. Environmental Protection

11. Available Accessories

ENGLISH

12. Technical Specifications

HWA

3300 K

HWA

3300 N

HWA

4000 N

HWA

5500 M

Mains voltage V 230 ∼ 1 230 ∼ 1 230 ∼ 1 230 ∼ 1

Frequency Hz 50 50 50 50

Rated output W 900 900 1300 1500

Rated current A 4.0 4.0 5.8 6.7

Fuse protection min. (time-lag or L-type circuit breaker) A 10 10 10 10

Running capacitor µF 12.5 12.5 20 20

Rated speed min

-1

2800 2800 2800 2800

Pump capacity max. l/h 3300 3300 4000 5500

Delivery head max. m 45 45 48 55

Delivery pressure max. bar 4.5 4.5 4.8 5.5

Max. suction head m 8 8 8 9

Temperature of the primed medium max. °C 50 50 50 50

Ambient temperature °C 5 … 40 5 … 40 5 … 40 5 … 40

Degree of protection IP 44 IP 44 IP 44 IP 44

Degree of protection I I I I

Insulation class F F F F

Materials

Pump casing

Pump shaft

Impeller

Noryl

Stainless steel

Noryl

Stainless steel

Noryl

Stainless steel

Noryl

Stainless steel

Noryl – 5x

Connections

Pump inlet thread (female)

Discharge port thread (male)

Hydromat hydrostatic pressure switch

Cut-in pressure approx. bar 1.5 1.5 1.5 1.5

Dimensions (without connections)

Length

Width

Height

450

245

395

450

245

395

450

245

395

480

245

400

Weights

Dry weight

Weight filled with water

8.6

10.1

8.8

10.3

11.4

12.9

13.3

15.3

Noise emission values (at max. pressure)

Sound power level L

Sound pressure level L

dB (A)

66.5

65.5

61.5

Max. length of extension cable

at 3 x 1.0 mm

lead cross-section

at 3 x 1.5 mm

lead cross-section

A 090 304 0521 B 090 305 2597 C 090 302 8521

D 1) 090 300 4231

2) 090 300 4258

3) 090 301 1858

E 090 305 0314 F 090 302 8432

G 090 302 8440 H 090 302 8475 I 090 302 8467

J 090 301 6817 K 090 301 8402 L 090 302 8203

M 090 102 6319

U3P0014.fm

www.elektra-beckum.de

ZINDEL - Technische Dokumentation und Multimedia, www.zindel.de

Metabo HWA 5500 M Operating instructions

Brand: Metabo

Model: HWA 5500 M

Type: Operating instructions

Download PDF

report

in other languages

dansk: Metabo HWA 5500 M Betjeningsvejledning

Metabo HWA 5500 M Operating instructions

Metabo HWA 5500 M Operating instructions

in other languages

Related papers

Other documents