Behringer Ultratone K1800FX Quick start guide

(Check Out behringer.com for Full Manual)

ULTRATONE

K3000FX/K1800FX/K900FX/K450FX

Ultra-Flexible 300/180/90/45-Watt 4/3-Channel PA System/

Keyboard Amplier with FX and FBQ Feedback Detection

3Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

Important Safety

Instructions

LIMITED WARRANTY

LEGAL DISCLAIMER

Terminals marked with this symbol carry

electrical current of su cient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modi cation should be performed only

by quali edpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be su cient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

quali ed personnel.

Caution

To reduce the risk of  re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects  lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by quali ed service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by quali ed

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not  t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories speci ed by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table speci ed by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

TECHNICAL SPECIFICATIONS AND APPEARANCES

ARE SUBJECT TO CHANGE WITHOUT NOTICE AND

ACCURACY IS NOT GUARANTEED. BEHRINGER IS

PART OF THE MUSIC GROUP MUSICGROUP.COM.

ALL TRADEMARKS ARE THE PROPERTY OF THEIR

RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO

LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED

BY ANY PERSON WHO RELIES EITHER WHOLLY OR

IN PART UPON ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN. COLORS AND

SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.

MUSIC GROUP PRODUCTS ARE SOLD THROUGH

AUTHORIZED FULLFILLERS AND RESELLERS ONLY.

FULLFILLERSAND RESELLERS ARE NOT AGENTS OF

MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED

UNDERTAKING OR REPRESENTATION. THIS MANUAL

IS COPYRIGHTED. NO PART OF THIS MANUAL MAY

BE REPRODUCED OR TRANSMITTED IN ANY FORM

OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING AND RECORDING OF ANY

KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS

WRITTEN PERMISSION OF MUSICGROUPIPLTD.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

§ 1 Warranty

(1) This limited warranty is valid only if you purchased

the product from a MUSIC Group Authorized Reseller in

the country of purchase. A list of authorized resellers can

be found on BEHRINGER’s website behringer. com under

“Where to Buy”, or you can contact the MUSIC Group o

closest to you.

(2) MUSICGroup* warrants the mechanical and

electronic components of this product to be free of defects

in material and workmanship if used under normal

operating conditions for a period of one (1) year from

the original date of purchase (see the Limited Warranty

terms in §4 below), unless a longer minimum warranty

period is mandated by applicable local laws. If the product

shows any defects within the speci ed warranty period

and that defect is not excluded under §4, MUSICGroup

shall, at its discretion, either replace or repair the product

using suitable new or reconditioned product or parts.

Incase MUSICGroup decides to replace the entire product,

thislimited warranty shall apply to the replacement

product for the remaining initial warranty period, i.e.,

one (1) year (or otherwise applicable minimum warranty

period) from the date of purchase of the original product.

(3) Upon validation of the warranty claim, the repaired

or replacement product will be returned to the user

freight prepaid by MUSICGroup.

(4) Warranty claims other than those indicated above

are expressly excluded.

PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF

OF PURCHASE COVERING YOUR LIMITED WARRANTY.

THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF

OFPURCHASE.

§ 2 Online registration

Please do remember to register your new BEHRINGER

equipment right after your purchase at behringer. com

under “Support” and kindly read the terms and conditions

of our limited warranty carefully. Registeringyour

purchase and equipment with us helps us process

your repair claims quicker and more e ciently.

Thankyouforyour cooperation!

§ 3 Return materials authorization

(1) To obtain warranty service, please contact the

retailer from whom the equipment was purchased.

Should your MUSIC Group Authorized Reseller not be

located in your vicinity, you may contact the MUSICGroup

Authorized Ful ller for your country listed under

“Support” at behringer. com. Ifyour country is not

listed, please check if your problem can be dealt with

by our “OnlineSupport” which may also be found under

“Support” at behringer. com. Alternatively,please submit

an online warranty claim at behringer. com BEFORE

returning the product. All inquiries must be accompanied

by a description of the problem and the serial number

of the product. Afterverifying the product’s warranty

eligibility with the original sales receipt, MUSICGroup

will then issue a ReturnMaterials Authorization

(“RMA”)number.

(2) Subsequently, the product must be returned in

its original shipping carton, together with the return

authorization number to the address indicated by

MUSICGroup.

(3) Shipments without freight prepaid will not

beaccepted.

§ 4 Warranty Exclusions

(1) This limited warranty does not cover consumable

parts including, but not limited to, fuses and batteries.

Where applicable, MUSICGroup warrants the valves or

meters contained in the product to be free from defects

in material and workmanship for a period of ninety (90)

days from date of purchase.

(2) This limited warranty does not cover the product

if it has been electronically or mechanically modi ed

in any way. If the product needs to be modi ed or

adapted in order to comply with applicable technical

or safety standards on a national or local level, inany

country which is not the country for which the

product was originally developed and manufactured,

thismodi cation/adaptation shall not be considered a

defect in materials or workmanship. Thislimited warranty

does not cover any such modi cation/adaptation,

regardless of whether it was carried out properly or not.

Under the terms of this limited warranty, MUSICGroup

shall not be held responsible for any cost resulting from

such a modi cation/adaptation.

(3) This limited warranty covers only the product

hardware. It does not cover technical assistance for

hardware or software usage and it does not cover

any software products whether or not contained in

the product. Any such software is provided “AS IS”

unless expressly provided for in any enclosed software

limitedwarranty.

(4) This limited warranty is invalid if the

factory- appliedserial number has been altered or

removed from theproduct.

(5) Free inspections and maintenance/repair work

are expressly excluded from this limited warranty,

inparticular, if caused by improper handling of the

product by the user. This also applies to defects caused

by normal wear and tear, in particular, of faders,

crossfaders, potentiometers, keys/buttons, guitar strings,

illuminantsand similar parts.

(6) Damage/defects caused by the following conditions

are not covered by this limited warranty:

• improper handling, neglect or failure to operate the

unit in compliance with the instructions given in

BEHRINGER user or service manuals;

• connection or operation of the unit in any way

that does not comply with the technical or safety

regulations applicable in the country where the

product is used;

• damage/defects caused by acts of God/Nature

(accident,  re,  ood, etc) or any other condition that

is beyond the control of MUSICGroup.

(7) Any repair or opening of the unit carried out by

unauthorized personnel (user included) will void the

limitedwarranty.

(8) If an inspection of the product by MUSICGroup

shows that the defect in question is not covered by the

limited warranty, the inspection costs are payable by

thecustomer.

(9) Products which do not meet the terms of this

limited warranty will be repaired exclusively at the buyer’s

expense. MUSICGroup or its authorized service center will

inform the buyer of any such circumstance. If the buyer

fails to submit a written repair order within 6 weeks after

noti cation, MUSICGroup will return the unit C.O.D. with

a separate invoice for freight and packing. Such costs will

also be invoiced separately when the buyer has sent in a

written repair order.

(10) MUSIC Group Authorized Resellers do not sell new

products directly in online auctions. Purchasesmade

through an online auction are on a “buyer beware” basis.

Online auction con rmations or sales receipts are not

accepted for warranty veri cation and MUSICGroup will

not repair or replace any product purchased through an

online auction.

§ 5 Warranty transferability

This limited warranty is extended exclusively to the

original buyer (customer of authorized reseller) andis

not transferable to anyone who may subsequently

purchase this product. No other person (reseller,etc.)

shallbe entitled to give any warranty promise on behalf

of MUSICGroup.

§ 6 Claim for damage

Subject only to the operation of mandatory applicable

local laws, MUSICGroup shall have no liability to the buyer

under this warranty for any consequential or indirect

loss or damage of any kind. In no event shall the liability

of MUSICGroup under this limited warranty exceed the

invoiced value of the product.

§ 7 Limitation of liability

This limited warranty is the complete and exclusive

warranty between you and MUSICGroup. It supersedes

all other written or oral communications related to this

product. MUSICGroup provides no other warranties for

this product.

§ 8 Other warranty rights and

nationallaw

(1) This limited warranty does not exclude or limit the

buyer’s statutory rights as a consumer in any way.

(2) The limited warranty regulations mentioned herein

are applicable unless they constitute an infringement of

applicable mandatory local laws.

(3)

This warranty does not detract from the seller’s

obligations in regard to any lack of conformity of the

product and any hidden defect.

§ 9 Amendment

Warranty service conditions are subject to change without

notice. For the latest warranty terms and conditions

and additional information regarding MUSICGroup’s

limited warranty, please see complete details online at

behringer. com.

* MUSICGroup Macao Commercial O shore Limited of

RuedePequim No. 202-A, Macau Finance Centre 9/J, Macau,

including all MUSICGroup companies

Page is loading ...

12 ULTRATONE K3000FX/K1800FX/K900FX/K450FX 13 Quick Start Guide

(EN) Step 1: Hook-Up

(ES) Paso 1: Conexión

(FR) Etape 1 : Connexions

(DE) Schritt 1:

Verkabelung

(PT) Passo 1: Conexões

Example of a setup using the ULTRATONE

Ejemplo de configuración con el ULTRATONE

Exemple de configuration utilisant l’ULTRATONE

Beispiel-Setup mit dem ULTRATONE

Exemplo de configuração utilizando o ULTRATONE

Live setup

Configuración para directo

Système de live

Live-Setup

Configuração ao vivo

Footswitch

BEHRINGER ULTRATONE K900FX

HPS3000

Keyboard

CD In

Mic In

Line In Line In

Phones

Drum Computer

XM8500

MP3 Player

Footswitch

BEHRINGER ULTRATONE K3000FX

HPS3000

XM8500

Line In

X2222USB

EP2000

Line Out

Main Outputs

Mic In 1

Phones

Line In 4 Line In 2Line In 3

Sub Out

B1800X PRO

B1520 PRO

Drum Computer

2 x Keyboard

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Hook-up

14 ULTRATONE K3000FX/K1800FX/K900FX/K450FX 15 Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(1) (3) (5) (6) (7) (9)

(2) (4) (8) (14)(12)(10)

(11) (13)

(15)

(25)(24)(19) (20)(18)(16)

(23)(22)(26)(17) (21)

(14)(12)(10)(8)

(9)(7)(6)(5)

(1)

(2)

(16)(15) (22) (21) (19) (25)(23) (24)

16 ULTRATONE K3000FX/K1800FX/K900FX/K450FX 17 Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX Controls

(EN) Step 2: Controls (ES) Paso 2: Controles

(1) The LEVEL controls adjust the signal level of

channels1 - 4 (K900FXandK450FX: channels 1 - 3).

(2) The four FX controls adjust the channel 1 - 4 signal

level at the input of the integrated eects processor

(K900FXand K450FX: three controls for channels1 - 3).

(3) The channel 4 signal (K3000FX and K1800FX only)

isnormally routed just to the PHONES output without

eects. This way you can practice without being

heard, or you can connect a metronome that you need

on headphones but not on speakers. By pressing the

TOMAIN button the signal will be additionally routed to

the speakers without eects.

(4) By pressing the TO LINE OUT button the channel 4

signal will be additionally routed to the LINE OUT output

without eects (K3000FX and K1800FX only). If you press

both the TO MAIN and TO LINE button, channel 4 will be

equal to channels 1 - 3. The signal will be routed to the

speakers and the LINE OUT output including eects.

(5) The ULTRATONE is equipped with a 7-band graphic

equalizer (K900FX and K450FX: 5-band graphic

equalizer). Use the EQ to adapt the sound to the

roomacoustics.

(6) Press the FBQ switch to activate the FBQ Feedback

Detection System. Thefrequencies causing feedback are

shown by the brightly lit fader LEDs. Simply lower the

level of the respective frequency range until feedback

disappears and the LED goes out.

(7) The FX display shows the currently selected preset.

TheSIG LED lights up when the eects processor receives

an input signal. When the CLIP LED lights up please

reduce the eects input signal by using the respective

FXcontrol(s) (2) .

(8) Turn the FX control to select an eects preset

(presetnumber starts ashing). Push the control briey

to conrm your selection.

(9) The LEVEL control in the master section is used to adjust

the main outputvolume.

(10) Turn the FX RET control to add the eect signal to the

main mix.

(11) Pressing the SHAPE button will add the Shape eect

to the main signal. TheShape function on your

ULTRATONE provides a revolutionary type of lter

that you can use to modify your keyboard sound

(K3000FXandK1800FXonly).

(12) Use the PHONES jack to plug in your headphones.

(13) The PHONES LEVEL control adjusts the headphones

output level (K3000FXand K1800FX only).

(14) Use the POWER switch to switch the ULTRATONE on or

o. You should always make sure that the POWER switch

is in the “O” position when initially connecting the unit

to the mains.

(15) MAINS CONNECTION. Use the power cord supplied with

the unit to connect it to the mains.

(16) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting

the unit to the mains, make sure that the voltage setting

matches your local voltage. Ablown fuse should only be

replaced by a fuse of the same type and rating. On some

units, the fuse holder can be switched to one of two

positions, i.e.230 V and 120 V. When operating the unit

outside Europe at 120 V, ahigher fuse rating is required.

(17) The GROUND LIFT switch disconnects (switch pressed)

the ground connection at the LINE OUT output to

eectively eliminate hum noise resulting from ground

loops (K3000FX and K1800FX only).

(18) Use the balanced LINE OUT XLR connectors to feed the

audio signal from your ULTRATONE to a mixing console

(K3000FX and K1800FX only). The LINE OUT signal is

post-EQ.

(19) These are the LINE OUT outputs on ¼" TS connectors

(K900FX and K450FX: one ¼" TS connector). Both XLR and

¼" TS LINE OUT connectors can be used simultaneously.

(20) For stereo operation the ULTRATONE features a

STEREOLINK facility. Youcan connect the OUT of the

ULTRATONE to the LINK IN of another keyboard amp that

serves as slave to achieve true stereo sound. When using

the ULTRATONE as slave, connect the LINK OUT of the

master amp to the IN (K3000FX andK1800FX only).

(21) The SUB OUT connector provides the line-level mono

subwoofer signal for connection to the input of a power

amp or active subwoofer.

(22) Connect your footswitch to the FOOT SW jack, so as to

activate/deactivate the eects processor.

(23) Use the CD IN connectors to connect the output of your

CD player, tape deck, or MP3 Player. This way you can

play along to music or keyboard tutorial CDs.

(24) These are the LINE inputs for channels 1-4

(K3000FX/K1800FX) / channels 1-3 (K900FX/K450FX)

on¼"TSconnectors. For mono input signals please use

the L(MONO) connector.

(25) Channel 1 is equipped with an additional XLR MIC input.

Due to internal +15V phantom power you can even use

condenser microphones. Both XLR and ¼" TS connectors

can be used simultaneously. In this case the LEVEL

control of channel 1 adjusts both the level of the LINE

and MIC signal.

Check Out behringer.com for Full Manual

(1) El control LEVEL regula el nivel de señal de los

canales1 - 4 (K900FXyK450FX: canales 1 - 3).

(2) Los cuatro controles FX regulan el nivel de la señal de

entrada del procesador de efectos proveniente de los

canales 1 - 4 (K900FX y K4500FX: tres controles para

loscanales 1 - 3).

(3) Por lo general, la señal del canal 4

(únicamenteK3000FX y K1800FX) esasignada sin

efectos a la salida de auriculares exclusivamente,

loque le permite practicar sin ser escucha-do o

utilizar un metrónomo que sólo sea escuchado a

través de los auriculares. Sin embargo, también puede

asignar la señal sin efectos del canal 4 a los altavoces

presionando el pulsador TOMAIN.

(4) El pulsador TO LINE OUT asigna la señal sin efectos del

canal 4 a la salida LINE OUT (únicamente K3000FX y

K1800FX). Si presiona ambos pulsadores TO MAIN y TO

LINE, el canal 4 se comportará de la misma manera que

los canales 1 - 3, es decir, laseñalcon efectos del canal

4 será asignada a los altavoces y a la salida LINE OUT.

(5) El ULTRATONE está equipado con un ecualizador gráco

de 7 bandas (K900FXy K450FX: ecualizador gráco de

5 bandas). Éste le puede ser muy útil para ajustar el

sonido del amplicador a la acústica del lugar.

(6) FBQ activa el Sistema FBQ de Detección de

Realimentación, mediante el cual se indican las

frecuencias que provocan realimentación en los

LEDs de los faders del ecualizador. Si se presenta el

caso, simplemente debe bajar el nivel del rango de

frecuencias indicado hasta que la realimentación cese,

elLED correspondiente se volverá a apagar.

(7) La pantalla FX indica el preset seleccionado en ese

momento. El LED SIG se ilumina al detectar una señal

en la entrada del procesador. Si se ilumina el LED

de saturación, CLIP, reduzca la señal de entrada del

procesador mediante el control FX correspondiente(2).

(8) Al girar este control se seleccionan los presets

de efectos (el nombre del preset parpadea).

Paraconrmar su selección pulse brevemente

elcontrol.

(9) El control LEVEL de la sección principal determina el

volumen general de salida del amplicador.

(10) El control FX RET le permite añadir la señal de efectos

a la señal principal.

(11) El pulsador SHAPE activa esta función en la señal

principal. La función Shape de su ULTRATONE le provee

un revolu-cionario ltro para alterar el sonido de su

teclado (únicamente K3000FX y K1800FX).

(12) Utilice la salida PHONES para conectar sus auriculares.

(13) El control PHONES LEVEL regula el nivel de salida de

los auriculares (únicamente K3000FX y K1800FX).

(14) Con el interruptor POWER se enciende el ULTRATONE.

Éste debe estar en la posición de apagado al conectar el

amplicador a la red de corrienteeléctrica.

(15) Utilice el cable suministrado para conectar su equipo a

la red de corrienteeléctrica.

(16) PORTAFUSIBLES / SELECCIÓN DE TENSIÓN. Antes de

conectar su ULTRATONE a la red de corriente eléctrica,

asegúrese de que el indicador de tensión de éste

corresponda a la tensión de red local. Si sustituye el

fusible debe emplear indispensablemente uno del

mismo tipo. En algunos aparatos el portafusibles

puede colocarse en dos posiciones distintas para

conmutar entre 230 V y 120 V. Si desea usar el aparato

fuera de Europa, a 120 V por ejemplo, debe utilizar un

fusible con valor distinto.

(17) Al activar el interruptor de separación de masa

GROUND LIFT (pulsadorpresionado) se interrumpe

la conexión a tierra de la salida LINEOUT,

eliminandoasí ruidos provoca-dos por bucles de

masa(únicamenteK3000FX y K1800FX).

(18) Utilice los conectores XLR balanceados designados

como LINE OUT para alimentar la señal de su

ULTRATONE a un mezclador (únicamente K3000FX

y K1800FX). La señal de la salida LINE OUT es

postecualizador, es decir, siemprese verá afectada por

los ajustes realizados en el ecualizador.

(19) Las salidas LINE OUT son mediante jacks mono de

6,3mm (K900FX y K450FX: un jack mono de 6,3 mm).

Ambos conectores XLR y jack mono de 6,3 mm para la

salida LINE OUT pueden usarse simultáneamente.

(20) Para operación en estéreo, el ULTRATONE dispone

la opción STEREO LINK. Ésta le permite conectar la

salida OUT del ULTRATONE a la entrada LINK IN de otro

amplicador de teclado, que funcionará como esclavo,

para obtener una auténtica reproducción estéreo.

Alutilizar el ULTRATONE como esclavo debe conectar la

salida LINK OUT del ampli-cador maestro a la entrada

IN de su ULTRATONE (únicamente K3000FX y K1800FX).

(21) La salida SUB OUT le permite alimentar la señal de

subwoofer con nivel de línea de su ULTRATONE a una

etapa de potencia o subwoofer activo.

(22) Para activar o desactivar los efectos mediante un

pedal, conecte éste en la entrada FOOT SW.

(23) Utilice la entrada CD IN para conectar la salida de un

reproductor de CD, casetera o MP3 a su amplicador.

Esto le permite tocar simultáneamente con su música

favorita o algún curso de teclado en CD.

(24) Entradas de línea de los canales 1-4 (K3000FX/

K1800FX) / canals 1-3 (K900FX/K450FX) mediante.

Para señales de entrada mono, utilice el conector

L(MONO).

(25) El canal 1 está equipado con una entrada XLR para

MIC(rófono). Laalimentación fantasma de +15 V le

permite incluso utilizar micrófonos de condensador.

Ambos conec-tores XLR y jack mono de 6,3 mm pueden

se usados simultá-neamente. En este caso, el control

LEVEL del canal 1 regula elnivel de la señal de línea y

de la señal de micrófono.

Si quiere acceder al manual de instrucciones

completo, vaya a la página web behringer.com

Page is loading ...

23Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

Specications Especicaciones técnicas

K3000FX K1800FX K900FX K450FX

Audio Inputs

Line In 1 - 4 ¼" TS connector

Input impedance approx. 30 k balanced

Stereo Link In ¼" TS connector

Input impedance approx. 20 k unbalanced

CD In RCA connector

Input impedance approx. 20 k unbalanced

Mic In 1 XLR connector

Input impedance approx. 2 k balanced

Audio Outputs

Headphones connector ¼" TRS connector

Line Out ¼" TS and XLR connector

Output impedance

¼" TS connector: approx.150  unbalanced

XLR connector: approx. 300  balanced

Stereo Link Out ¼" TS connector

Output impedance approx. 150  unbalanced

Sub Out ¼" TS connector

Output impedance approx. 150  unbalanced

Equalizer

Type Graphic EQ with FBQ Feedback Detection

Frequency range 63 Hz / 160 Hz / 400 Hz / 1 kHz / 2.5 kHz / 6.3 kHz / 12 kHz 63 Hz / 250 Hz / 1 kHz / 3.5 kHz / 12 kHz

Bandwidth 2/3-oct.

Control range +12 to -12 dB

Digital Eects Processor

Converters 24-bit sigma-delta, 64/128-times oversampling

Sampling rate 40 kHz

System Specications

Power amp output 300 Watts 180 Watts 90 Watts 45 Watts

Loudspeaker

Type

15'' BUGERAvv woofer and

custom-made 1'' driver

12'' BUGERA woofer and

custom-made 1'' driver

12'' BUGERA woofer and

custom-made 1'' driver

10'' BUGERA speaker

Input impedance 4 

Power Supply

Mains Voltage

USA/Canada 120 V~, 60 Hz

U.K./Australia 230 V~, 50 Hz

Europe 230 V~, 50 Hz

China/Korea 220 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

General export model 120/230 V~, 50 - 60 Hz

Power consumption approx. 350 Watts approx. 290 Watts approx. 150 Watts approx. 75 Watts

Fuse

100 - 120 V~: 6.3 A H 250 V

220 - 240 V~: 3.15 A H 250 V

100 - 120 V~: 6.3 A H 250 V

220 - 240 V~: 3.15 A H 250 V

100 - 120 V~: 3.15 A H 250 V

220 - 240 V~: 1.6 A H 250 V

100 - 120 V~: 2.5 A H 250 V

220 - 240 V~: 1.25 A H 250 V

Mains connection Standard IEC receptacle

Dimensions/Weight

Dimensions

approx. 20 ⁄ x 23 ½ x 16"

approx. 530 x 597 x 406 mm

approx. 16 ⁄ x 19 ⁄ x 11 ¾"

approx. 429 x 492 x 299 mm

approx. 16 ⁄ x 19 ⁄ x 11 ¾"

approx. 429 x 492 x 299 mm

approx. 16 ½ x 17 ⁄ x 11 ¾"

approx. 419 x 441 x 299 mm

Weight approx. 70.10 lbs / 31.8 kg approx. 42.32 lbs / 19.2 kg approx. 39.90 lbs / 18.1 kg approx. 34.83 lbs / 15.8 kg

K3000FX K1800FX K900FX K450FX

Entradas de Audio

Entradas de línea 1 - 4 jack mono de 6,3 mm

Impedancia de entrada aprox. 30 k balanceada

Entrada Stereo Link jack mono de 6,3 mm

Impedancia de entrada aprox. 20 k no balanceada

Entrada de CD conector RCA

Impedancia de entrada aprox. 20 k no balanceada

Entrada de micrófono conector XLR

Impedancia de entrada aprox. 2 k balanceada

Salidas de Audio

Conector de auriculares jack estéreo de 6,3 mm

Salida de línea jack mono de 6,3 mm y conector XLR

Impedancia de salida

jack mono de 6,3 mm: aprox.150  no balanceada

XLR: aprox. 300  balanceada

Salida Stereo Link jack mono de 6,3 mm

Impedancia de salida aprox. 150  no balanceada

Salida para Subwoofer jack mono de 6,3 mm

Impedancia de salida aprox. 150  no balanceada

Ecualizador

Tipo Ecualizador gráco con detección de realimentación FBQ

Rangos de frecuencia 63 Hz / 160 Hz / 400 Hz / 1 kHz / 2.5 kHz / 6.3 kHz / 12 kHz 63 Hz / 250 Hz / 1 kHz / 3.5 kHz / 12 kHz

Ancho de banda 2/3 oct.

Rango de amplicación +12 a -12 dB

Procesador de Efectos Digital

Convertidores sigma-delta de 24 bits, sobremuestreo de 64/128 veces

Frecuencia de muestreo 40 kHz

Especicaciones de Sistema

Potencia de salida 300 W 180 W 90 W 45 W

Altavoz

Tipo

woofer BUGERA de 15" y

tweeter especial de 1''

woofer BUGERA de 12" y

tweeter especial de 1''

woofer BUGERA de 12" y

tweeter especial de 1''

altavoz BUGERA de 10"

Impedancia de entrada 4 

Suministro de Corriente

Tensión de Red

EE.UU./Canadá 120 V~, 60 Hz

R.U./Australia 230 V~, 50 Hz

Europa 230 V~, 50 Hz

China/Corea 220 V~, 50 Hz

Japón 100 V~, 50 - 60 Hz

Modelo general de exportación 120/230 V~, 50 - 60 Hz

Consumo de potencia aprox. 350 W aprox. 290 W aprox. 150 W aprox. 75 W

Fusible

100 - 120 V~: 6,3 A H 250 V

220 - 240 V~: 3,15 A H 250 V

100 - 120 V~: 6,3 A H 250 V

220 - 240 V~: 3,15 A H 250 V

100 - 120 V~: 3,15 A H 250 V

220 - 240 V~: 1,6 A H 250 V

100 - 120 V~: 2,5 A H 250 V

220 - 240 V~: 1,25 A H 250 V

Conector de red conector IEC estándar

Dimensiones/Peso

Dimensiones aprox. 530 x 597 x 406 mm aprox. 429 x 492 x 299 mm aprox. 429 x 492 x 299 mm aprox. 419 x 441 x 299 mm

Peso aprox. 31,8 kg aprox. 19,2 kg aprox. 18,1 kg aprox. 15,8 kg

Page is loading ...

27Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

Other important information

1. Register online. Please register your new

MUSIC Group equipment right after you purchase it by

visiting behringer. com. Registering your purchase using

our simple online form helps us to process your repair

claims more quickly and eciently. Also, read the terms

and conditions of our warranty, ifapplicable.

2. Malfunction. Should your MUSICGroup Authorized

Reseller not be located in your vicinity, you may contact

the MUSIC Group Authorized Fulller for your country listed

under “Support” at behringer. com. Should your country not

be listed, please check if your problem can be dealt with

by our “OnlineSupport” which may also be found under

“Support” at behringer. com. Alternatively, please submit an

online warranty claim at behringer. com BEFORE returning

theproduct.

3. Power Connections. Before plugging the unit

into a power socket, please make sure you are using the

correct mains voltage for your particular model. Faulty fuses

must be replaced with fuses of the same type and rating

without exception.

Aspectos importantes

1. Registro online. Le recomendamos que

registre su nuevo aparato MUSIC Group justo después de

su compra accediendo a la página web behringer. com.

Elregistro de su compra a través de nuestro sencillo

sistema online nos ayudará a resolver cualquier

incidencia que se presente a la mayor brevedad posible.

Además,aproveche para leer los términos y condiciones de

nuestra garantía, si es aplicable en sucaso.

2. Averías. En el caso de que no exista un distribuidor

MUSIC Group en las inmediaciones, puede ponerse en

contacto con el distribuidor MUSIC Group de su país,

queencontrará dentro del apartado “Support” de nuestra

página web behringer. com. En caso de que su país no

aparezca en ese listado, acceda a la sección “Online Support”

(quetambiénencontrará dentro del apartado “Support” de

nuestra páginaweb) y compruebe si su problema aparece

descrito y solucionado allí. De forma alternativa, envíenos a

través de la página web una solicitud online de soporte en

periodo de garantía ANTES de devolvernos el aparato.

3. Conexiones de corriente. Antes de enchufar

este aparato a una salida de corriente, asegúrese de que dicha

salida sea del voltaje adecuado para su modelo concreto.

En caso de que deba sustituir un fusible quemado, deberá

hacerlo por otro de idénticas especicaciones, sinexcepción.

1. Enregistrez-vous en ligne. Prenez le

temps d’enregistrer votre produit MUSIC Group aussi vite

que possible sur le site Internet behringer. com. Le fait

d’enregistrer le produit en ligne nous permet de gérer

les réparations plus rapidement et plus ecacement.

Prenezégalement le temps de lire les termes et conditions

de notre garantie.

2. Dysfonctionnement. Si vous n’avez pas de

revendeur MUSIC Group près de chez vous, contactez le

distributeur MUSIC Group de votre pays: consultez la liste

des distributeurs de votre pays dans la page “Support” de

notre site Internet behringer. com. Si votre pays n’est pas

dans la liste, essayez de résoudre votre problème avec notre

“aideen ligne” que vous trouverez également dans la section

“Support” du site behringer. com. Vous pouvez également

nous faire parvenir directement votre demande de réparation

sous garantie par Internet sur le site behringer. com AVANT de

nous renvoyer le produit.

3. Raccordement au secteur. Avant de relier

cet équipement au secteur, assurez-vous que la tension

secteur de votre région soit compatible avec l’appareil.

Veillez à remplacer les fusibles uniquement par des modèles

exactement de même taille et de même valeur électrique —

sans aucune exception.

1. Online registrieren. Bitte registrieren Sie Ihr

neues MUSIC Group-Gerät direkt nach dem Kauf auf der

Website behringer. com. Wenn Sie Ihren Kauf mit unserem

einfachen online Formular registrieren, können wir Ihre

Reparaturansprüche schneller und ezienter bearbeiten.

Lesen Sie bitte auch unsere Garantiebedingungen,

fallszutreend.

2. Funktionsfehler. Sollte sich kein MUSIC Group

Händler in Ihrer Nähe benden, können Sie den MUSIC Group

Vertrieb Ihres Landes kontaktieren, der auf behringer. com

unter “Support” aufgeführt ist. Sollte Ihr Land nicht

aufgelistet sein, prüfen Sie bitte, ob Ihr Problem von unserem

“Online Support” gelöst werden kann, den Sie ebenfalls

auf behringer. com unter “Support” nden. Alternativ reichen

Sie bitte Ihren Garantieanspruch online auf behringer. com

ein, BEVOR Sie das Produktzurücksenden.

3. Stromanschluss. Bevor Sie das Gerät an

eine Netzsteckdose anschließen, prüfen Sie bitte, obSie

die korrekte Netzspannung für Ihr spezielles Modell

verwenden. Fehlerhafte Sicherungen müssen ausnahmslos

durch Sicherungen des gleichen Typs und Nennwerts

ersetztwerden.

1. Registre-se online. Por favor, registre seu

novo equipamento MUSIC Group logo após a compra

visitando o site behringer. com Registrar sua compra

usando nosso simples formulário online nos ajuda a

processar seus pedidos de reparos com maior rapidez e

eciência. Além disso, leia nossos termos e condições de

garantia, caso seja necessário.

2. Funcionamento Defeituoso.

Casoseufornecedor MUSIC Group não esteja localizado

nas proximidades, você pode contatar um distribuidor

MUSIC Group para o seu país listado abaixo de “Suporte”

embehringer. com. Se seu país não estiver na lista, favor

checar se seu problema pode ser resolvido com o nosso

“Suporte Online” que também pode ser achado abaixo de

“Suporte”em behringer. com. Alternativamente, favor enviar

uma solicitação de garantia online em behringer. com ANTES

da devolução do produto.

3. Ligações. Antes de ligar a unidade à tomada,

assegure-se de que está a utilizar a voltagem correcta para

o modelo em questão. Os fusíveis com defeito terão de ser

substituídos, sem qualquer excepção, por fusíveis do mesmo

tipo e corrente nominal.

Important information Informations importantes

Weitere wichtige

Informationen

Outras Informações

Importantes

Dados técnicos

K3000FX K1800FX K900FX K450FX

Entradas de Áudio

Line In 1 - 4 Ficha jack mono de 6,3 mm

Impedância de entrada Aprox. 30 k balanceada

Stereo Link In Ficha jack mono de 6,3 mm

Impedância de entrada Aprox. 20 k não balanceada

CD In Conector RCA

Impedância de entrada Aprox. 20 k não balanceada

Mic In 1 Conector XLR

Impedância de entrada Aprox. 2 k balanceada

Saídas Áudio

Conector dos auscultadores Ficha jack estéreo de 6,3 mm

Line Out Ficha jack mono de 6,3 mm e XLR

Impedância de saída

Ficha jack mono de 6,3 mm: Aprox. 150  não balanceada

Conector XLR: Aprox. 300  balanceada

Stereo Link Out Ficha jack mono de 6,3 mm

Impedância de saída Aprox. 150  não balanceada

Sub Out Ficha jack mono de 6,3 mm

Impedância de saída Aprox. 150  não balanceada

Equalizador

Tipo Equalizador Gráco com Detecção de Retorno FBQ

Intervalo de Frequência 63 Hz / 160 Hz / 400 Hz / 1 kHz / 2.5 kHz / 6.3 kHz / 12 kHz 63 Hz / 250 Hz / 1 kHz / 3.5 kHz / 12 kHz

Largura de Banda 2/3-oct.

Intervalo de Controlo +12 a -12 dB

Processador de Efeitos Digitais

Conversores sigma-delta 24 bits, sobreamostragem de 64/128-vezes

Taxa de Amostragem 40 kHz

Especicações do Sistema

Saída do amplicador de potência 300 Watts 180 Watts 90 Watts 45 Watts

Coluna

Tipo

Woofer BUGERA 15'' e

controlador 1" personalizado

Woofer BUGERA 12'' e

controlador 1" personalizado

Woofer BUGERA 12'' e

controlador 1" personalizado

Coluna BUGERA 10''

Impedância de Entrada 4 

Fornecimento de Energia

Corrente Eléctrica

EUA/Canadá 120 V~, 60 Hz

R.U./Austrália 230 V~, 50 Hz

Europa 230 V~, 50 Hz

China/Coréia 220 V~, 50 Hz

Japão 100 V~, 50 - 60 Hz

Modelo de Exportação Genérico 120/230 V~, 50 - 60 Hz

Consumo de energia Aprox. 350 Watts Aprox. 290 Watts Aprox. 150 Watts Aprox. 75 Watts

Fusível

100 - 120 V~: 6,3 A H 250 V

220 - 240 V~: 3,15 A H 250 V

100 - 120 V~: 6,3 A H 250 V

220 - 240 V~: 3,15 A H 250 V

100 - 120 V~: 3,15 A H 250 V

220 - 240 V~: 1,6 A H 250 V

100 - 120 V~: 2,5 A H 250 V

220 - 240 V~: 1,25 A H 250 V

Ligação à corrente Receptáculo IEC padrão

Dimensões/Peso

Dimensões Aprox. 530 x 597 x 406 mm Aprox. 429 x 492 x 299 mm Aprox. 429 x 492 x 299 mm Aprox. 419 x 441 x 299 mm

Peso Aprox. 31,8 kg Aprox. 19,2 kg Aprox. 18,1 kg Aprox. 15,8 kg

29Quick Start Guide

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

FEDERAL COMMUNICATIONS

COMMISSION COMPLIANCE

INFORMATION

Responsible Party Name: MUSIC Group Services US Inc.

Address: 18912 North Creek Parkway,

Suite 200 Bothell, WA 98011,

USA

Phone/Fax No.: Phone: +1 425 672 0816

Fax: +1 425 673 7647

ULTRATONE K3000FX/K1800FX/K900FX/K450FX

complies with the FCC rules as mentioned in the followingparagraph:

This equipment has been tested and found to comply with the limits for a ClassB

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician forhelp.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Important information:

Changes or modications to the equipment not expressly approved by MUSIC Group

can void the user’s authority to use the equipment.

ULTRATONE

K3000FX/K1800FX/K900FX/K450FX

We Hear You

Behringer Ultratone K1800FX, Ultratone K3000FX, Ultratone K450FX, Ultratone K900FX Quick start guide

Related papers

Other documents