OWNER S MANUAL
11.2 Universal Ceiling Mount Monitor
M
EXIT
AV
MENU
POWER
E
10
DC 12V
9W
11.2 TFT-LCD
16:9
2400x480
2A/V RCAInputs
DC 12V
3W
Right 2.8MHz Left 2.3MHz
Active Matrix TFT
Power Requirements
Power Consumption
Screen Size
Screen Format
Resolution Pixel
A/V Inputs
Dimensions(
With shroud)
IR Power Requirements
IR Power Consumption
IR Transmitter Frequency
LCD Panel Type
Compatible video standard
NTSC/PALAuto Select
SPECIFICATIONS
Note :This equipment has beentested and found to complywith the limits for
a ClassAdigital device, pursuant topart 15of the FCCRules. These limits
are designedto providereasonable protection againstharmful interference
when theequipment isoperated in acommercial environment.
This equipmentgenerates, uses,and can radiateradio frequencyenergy and,
if notinstalled andused in accordancewith theinstruction manual, maycause
harmful interferenceto radiocommunications. Operation ofthis equipmentin
a residentialarea islikely to causeharmful interferencein which casethe user
will berequired tocorrect the interferenceat hisown expense.
Dimensions(Without shroud)
14.6(L)X12.6(W)X3.3(H)inches
14.3(L)X12.4(W)X2.4(H)inches
2
CAUTION 4
INSTALLATION 5
NAME AND FUNCTION OF EACH PARTS 6
Unit 6
Remote Control 7
CONNECTIONS 8
HOW TO OPERATION THE MONITOR 9
Releasing The Monitor 9
How To Watch Monitor 9
SPECIFICATIONS 10
Please read this User
,
s Manual in detail and use the set properly.
9
CONTENTSHOW TO OPERATE THE MONITOR
Releasing the Monitor
Push the open button (located on the front edge of the screen housing)
and lower the monitor to the desired angle. You can also adjust the
swivel angle.
How to watch the monitor
1. Connect the monitor to the external devices.
2. Press the POWER button on either the remote control or the unit once to turn
the power on.
Press the same POWER button to turn the power off.
3.Turn on the external devices and view.
Make this arrow in DOWN
direction only.
PULLBUTTON
M
EXIT
AV
MENU
POWER
E
POWER
UNIT
REMOTE CONTROLLER
POWER
3
8
CONNECTIONS
CAUTION
Please read and observe all warnings and instructions in this owner s manual
and those marked on the unit. Retain this booklet for future reference.
There are two kinds of alarm symbols as follows:
WARNING
WARNING
CAUTION
The lightening flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of
dangerous voltage within the product s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to
people.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the product.
Installation of all TV monitors
must be out of thedriver s
field of sight.
Do not try and servicethese
products yourself, Seek only
a qualified service center or
factory service center.
Be careful not to dropor
apply under pressure to the
front panel of your video
monitor. If the screen cracks
due to misuse, your warranty
will be void!
Do not mount the productwhere
it will obstruct the deploymentof
the airbag or in anarea whereit
would affect the vehicular control.
Also be careful to avoidmounting
the product where it canbecome
hazardous during sudden stops or
in the event of anaccident.
Be careful not to overloadyour
cigarette lighter plug by adding
more than one device ata time.
Use extra caution with anyliquids
in your car.If you oryour child
Spills any liquid on theseproducts,
pull your vehicle to theroadside
and turn the key off to disconnect
or wipe the products witha towel.Do not
operate the equipment until allliquids have
either evaporated or you havehad themonitor
inspected at a service centerby aqualified
technician, Severe harm or dangercan
Occur.
Use only a damp clothto clean
the screen and use onlypurified
water on the cloth. Wring out all
excess water prior to wipingthe
screen. Do not use anycleaners
or chemicals to clean thescreen.
In most cases a drycloth willdo!
P
O
W
E
R
A
V
M
E
N
U
,
,
CAMCORDER
GAME
White AUDIO(L)
Red AUDIO(R)
Yellow VIDEO
CAMCORDER
GAME
White AUDIO(L)
Red AUDIO(R)
Yellow VIDEO
AV Input
(AV 2)
(AV 1)
AV Input
YELLOW
ACC
BLACK
RED
+12VDCBattery
Chassis Ground
Door Trigger
WHITE
+ Door Trigger -
7
NAME AND FUNCTION OF EACH PART
Interface Switch Function
Power Power ON/OFF
AV Signal Select
Menu Press this button for OSD menu.
And select menu option
-
+
Increase current option value.
Decrease current option value.
LCD MONITOR
REMOTE CONTROL UNIT
POWER KEY
AV1/AV2 KEY
+KEY
-KEY
MENU KEY
CAUTION
4
Quality installationsare best
performed byqualified and
certifled installers.
Don ttouch theunit if thereis
a flashof lightning.It may
receive anelectric shock.
Do notcover heaterducts or vents.
This maycause afire or anelectric
shock.
Watching themonitor for an
extended periodof time
with theengine turnedoff
may depletethe vehicles
battery.
This productis designedfor
operation witha 12VoltDC,
negative groundvehicle. It
is notsuitable foroperation
under otherconditions or
voltages.
1.Theoperatingtemperature of this product is limited to 14 F~140 F
(-10 C~60 C).
Your vehicle can reach temperatures up to 100 C in the summertime.
2. When your vehicle is extremely hot or cold you must allow time for your air
conditioner or heater to cool or heat the vehicle and for operating temperatures
to return to normal operating ranges. Your monitor will return to its normal
functions when these operating ranges are achieved.
3. Optimum picture quality is achieved when you are directly in front of the monitor
(+/-45 degrees).
4. If the buttons get stuck, please try to press the up of buttons, it will get back.
It won't impact using normal.
5. If you cann't find the files name in list when playing, please reset units or turn
off/onoveragain.
6. If the unit cann't be change mode when playing some special files which the
unit didn't support, please reset units or turn off/on over again.
CAUTION
Check Point
OSD MENU EXIT Button
POWER Button
MENU Button
M
EXIT
AV
MENU
POWER
AV Select Button
+/- Buttons
Dome Light Button
ON DOOR OFF
E
M
EXIT
AV
MENU
POWER
E
5
6
INSTALLATION NAME AND FUNCTION OF EACH PART
Unit
Dome light
Monitor
(Front)
Monitor
(Rear)
Infrared Transmitter
1. Open the package and check that these items are presents.
INSTALLATION PLATE
UNIT
SCREWA SCREW B
2. Connect the external compoments to the RCAcable orAV output.
(Refer to the connection diagram on page 8)
3.Match the position of installation bracket and
installation plate with screwA.
4.Tighten the unit with the supplied
screw B.
Audio Video
AV2 INPUTS
RESET
/
