DeWalt DCR006 User manual

Type
User manual

This manual is also suitable for

DCR006
12V/20V Max* Wireless Bluetooth
®
Speaker
Haut-parleur Bluetooth
MD
sans fil, 12V /20V max*
Altavoz inalámbrico de Bluetooth
®
de 12V/20V Máx*
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-DEWALT • www.dewalt.com
Page dimensions: 8.5 x 5.5 inches
1
Page dimensions: 8.5 x 5.5 inches
English
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
NOTICE: Indicates a practice not related to personal
injury which, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY D
EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT
(1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction
manual.
General Safety Warnings
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Unplug this apparatus during lightning storms or when unused
for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
Page dimensions: 8.5 x 5.5 inches
2
English
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and speaker.
Connect the equipment into an outlet on a circuit different from
that to which the speaker is connected.
Consult the dealer or an experienced radio/TV technician for
help.
The label on your tool may include the following symbols. The
nameplate label is located on bottom of unit. The symbols and
their definitions are as follows:
V ................... volts A ......................amperes
Hz ................. hertz W .....................watts
min ............... minutes
or AC ..........alternating
or DC ... direct current current
................. Class I Construction or AC/DC ...alternating
.....................
(grounded) ........................or direct
................. Class II Construction current
(double insulated)
n
o ....................no load
…/min .......... per minute speed
BPM ............. beats per minute
n ......................rated
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
14. Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus
The lightning flash with arrow head within a triangle is intended
to tell the user that parts inside the product are a risk of electric
shock to persons.
The exclamation point within a triangle is intended to tell the
user that important operating and servicing instructions are in
the papers with the appliance.
Additional Safety Rules for Bluetooth
®
Speaker
DO NOT splash or immerse in water or other liquids.
Please note that changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: The Bluetooth
®
word mark and logos are registered
trademarks owned by the Bluetooth
®
, SIG, Inc. and any use of
such marks by D
EWALT is under license. Other trademarks and
trade names are those of their respective owners.
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
Page dimensions: 8.5 x 5.5 inches
3
English
WARNING: Fire hazard. Never attempt to open the battery pack
for any reason. If the battery pack case is cracked or damaged, do
not insert into the charger. Do not crush, drop or damage the battery
pack. Do not use a battery pack or charger that has received a sharp
blow, been dropped, run over or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped on). Damaged battery packs
should be returned to the service center for recycling.
WARNING: Fire hazard. Do not store or carry the battery
pack so that metal objects can contact exposed battery
terminals. For example, do not place the battery pack in aprons,
pockets, tool boxes, product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting batteries can possibly
cause fires if the battery terminals inadvertently come in
contact with conductive materials such as keys, coins, hand
tools and the like. The US Department of Transportation Hazardous
Material Regulations (HMR) actually prohibit transporting batteries in
commerce or on airplanes (e.g., packed in suitcases and carry-on
luggage) UNLESS they are properly protected from short circuits. So
when transporting individual battery packs, make sure that the battery
terminals are protected and well insulated from materials that could
contact them and cause a short circuit.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium ion battery packs are burned.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If battery
liquid gets into the eye, rinse water over the open eye for 15
minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic
carbonates and lithium salts.
IPM ............... impacts per minute
........................speed
RPM ............. revolutions per
.....................earthing
minute terminal
sfpm ............. surface feet
..................... safety alert
..................... per minute symbol
SPM ............. strokes per minute
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to include the
catalog number and voltage. Consult the chart at the end of this
manual for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below and
then follow charging procedures outlined.
READ ALL INSTRUCTIONS
Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable liquids,
gases or dust. Inserting or removing the battery pack from the
charger may ignite the dust or fumes.
NEVER force the battery pack into the charger. DO NOT
modify the battery pack in any way to fit into a non-
compatible charger as battery pack may rupture causing
serious personal injury. Consult the chart at the end of this
manual for compatibility of batteries and chargers.
Charge the battery packs only in designated D
EWALT chargers.
DO NOT splash or immerse in water or other liquids.
Do not store or use the tool and battery pack in locations
where the temperature may reach or exceed 105°F (40°C)
(such as outside sheds or metal buildings in summer). For
best life store battery packs in a cool, dry location.
Page dimensions: 8.5 x 5.5 inches
4
English
Before using the charger, read all instructions and cautionary
markings on the charger, battery pack and product using the
battery pack.
WARNING: Shock hazard. Do not allow any liquid to get inside the
charger. Electric shock may result.
CAUTION: Burn hazard. To reduce the risk of injury, charge only
D
EWALT rechargeable battery packs. Other types of batteries may
overheat and burst resulting in personal injury and property damage.
NOTICE: Under certain conditions, with the charger plugged into the
power supply, the charger can be shorted by foreign material. Foreign
materials of a conductive nature, such as, but not limited to, grinding
dust, metal chips, steel wool, aluminum foil or any buildup of metallic
particles should be kept away from the charger cavities. Always
unplug the charger from the power supply when there is no battery
pack in the cavity. Unplug the charger before attempting to clean.
WARNING:
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger and
battery pack are specifically designed to work together.
These chargers are not intended for any uses other than
charging D
EWALT rechargeable batteries. Any other uses
may result in risk of fire, electric shock or electrocution.
Do not expose the charger to rain or snow.
Pull by the plug rather than the cord when disconnecting
the charger. This will reduce the risk of damage to the electric
plug and cord.
Make sure that the cord is located so that it will not be
stepped on, tripped over or otherwise subjected to damage
or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk of
fire, electric shock or electrocution.
Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek medical
attention.
WARNING: Burn hazard. Battery liquid may be flammable if
exposed to spark or flame.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corp-
oration) Seal on the nickel cadmium, nickel metal
hydride or lithium ion batteries (or battery packs)
indicate that the costs to recycle these batteries (or
battery packs) at the end of their useful life have already
been paid by D
EWALT. In some areas, it is illegal to
place spent nickel cadmium, nickel metal hydride or lithium ion
batteries in the trash or municipal solid waste stream and the RBRC
program provides an environmentally conscious alternative.
RBRC™, in cooperation with D
EWALT and other battery users, has
established programs in the United States and Canada to facilitate
the collection of spent nickel cadmium, nickel metal hydride or lithium
ion batteries. Help protect our environment and conserve natural
resources by returning the spent nickel cadmium, nickel metal hydride
or lithium ion batteries to an authorized D
EWALT service center or
to your local retailer for recycling. You may also contact your local
recycling center for information on where to drop off the spent
battery.
RBRC™ is a registered trademark of the Rechargeable Battery
Recycling Corporation.
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for battery chargers.
Page dimensions: 8.5 x 5.5 inches
5
English
slots and result in excessive internal heat. Place the charger
in a position away from any heat source. The charger is ventilated
through slots in the top and the bottom of the housing.
Do not operate the charger with a damaged cord or plug.
Do not operate the charger if it has received a sharp blow,
been dropped or otherwise damaged in any way. Take it to
an authorized service center.
Do not disassemble the charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution or fire.
Disconnect the charger from the outlet before attempting
any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce this risk.
NEVER attempt to connect 2 chargers together.
The charger is designed to operate on standard 120V
household electrical power. Do not attempt to use it on any
other voltage. This does not apply to the vehicular charger.
Chargers
Your speaker uses a DEWALT charger.
L
FIG. 1
Be sure to read all safety instructions
before using your charger. Consult the
chart at the end of this manual for
compatibility of chargers and battery
packs.
Charging Procedure
(Fig. 1)
1. Plug the charger into an appropriate
outlet before inserting the battery
pack.
When operating a charger outdoors, always provide a dry
location and use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge number
of the wire, the greater the capacity of the cable, that is, 16 gauge
has more capacity than 18 gauge. An undersized cord will cause a
drop in line voltage resulting in loss of power and overheating. When
using more than one extension to make up the total length, be sure
each individual extension contains at least the minimum wire size.
The following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The lower the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Ampere
Rating
Volts Total Length of Cord
in Feet (meters)
120 V 25
(7.6)
50
(15.2)
100
(30.5)
150
(45.7)
240 V 50
(15.2)
100
(30.5)
200
(61.0)
300
(91.4)
More
Than
Not
More
Than
AWG
0 6 18 16 16 14
610 1816 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
Do not place any object on top of the charger or place the
charger on a soft surface that might block the ventilation
Page dimensions: 8.5 x 5.5 inches
6
English
Charge Indicators
This charger is designed to detect certain problems that can arise.
Problems are indicated by the red light flashing at a fast rate. If this
occurs, re-insert the battery pack into the charger. If the problem
persists, try a different battery pack to determine if the charger is
working properly. If the new pack charges correctly, then the original
pack is defective and should be returned to a service center or other
collection site for recycling. If the new battery pack elicits the same
trouble indication as the original, have the charger and the battery
pack tested at an authorized service center.
HOT/COLD DELAY
DCB101
This charger has a hot/cold delay feature: when the charger detects a
battery that is hot, it automatically starts a delay, suspending charging
until the battery has cooled. After the battery has cooled, the charger
automatically switches to the pack charging mode. This feature
ensures maximum battery life. The red light flashes long, then short
while in the hot/cold delay mode.
DCB107, DCB112
The DCB107 and DCB112 chargers have a hot/cold delay feature.
When the charger detects a battery that is hot, it automatically delays
charging until the battery has cooled. When the charger detects a
battery that is cold, it automatically delays charging until the battery
has warmed.
The red light will continue to blink, but a yellow indicator light will
be illuminated during this operation. Once the battery has cooled,
the yellow light will turn off and the charger will resume the charging
procedure.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge
indicator showing Pack Charged.
2. Insert the battery pack (L) into the charger, as shown in Figure 1,
making sure the pack is fully seated in charger. The red (charging)
light will blink continuously, indicating that the charging process
has started.
3. The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and may be
used at this time or left in the charger.
Indicator Light Operation
DCB101
PACK CHARGING
PACK CHARGED
x
HOT/COLD DELAY
PROBLEM PACK OR CHARGER
PROBLEM POWERLINE
DCB107, DCB112
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
Page dimensions: 8.5 x 5.5 inches
7
English
avoid placing the charger or battery pack in a warm environment
such as in a metal shed or an uninsulated trailer.
3. A cold battery pack will charge at about half the rate of a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery pack warms.
4. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other
appliance;
b. Check to see if receptacle is connected to a light switch which
turns power off when you turn out the lights;
c. Move the charger and battery pack to a location where the
surrounding air temperature is approximately 65 °F 75 °F
(18° – 24°C);
d. If charging problems persist, take the apparatus, battery pack
and charger to your local service center.
5. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously. DO
NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack
whenever you desire with no adverse effect on the battery pack.
6. Foreign materials of a conductive nature such as, but not limited
to, grinding dust, metal chips, steel wool, aluminum foil, or any
buildup of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply when
there is no battery pack in the cavity. Unplug the charger before
attempting to clean.
7. Do not freeze or immerse the charger in water or any other liquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside the
charger. Electric shock may result.
WEAK BATTERY PACKS: Weak batteries will continue to function
but should not be expected to perform as much work.
FAULTY BATTERY PACKS: This charger will not charge a faulty
battery pack. The charger will indicate faulty battery pack by refusing
to light or by displaying problem pack or charger.
NOTE: This could also mean a problem with a charger.
PROBLEM POWER LINE (DCB101)
Some chargers have a Problem Powerline indicator. When the charger
is used with some portable power sources such as generators or
sources that convert DC to AC, the charger may temporarily suspend
operation, flashing the red light with two fast blinks followed by a
pause. This indicates the power source is out of limits.
Wall Mounting
DCB107, DCB112
These chargers are designed to be wall mountable or to sit upright on
a table or work surface.
If wall mounting, locate the charger within reach of an electrical outlet.
Mount the charger securely using drywall screws at least 1" (25.4 mm)
long, screwed into wood to an optimal depth leaving approximately
7/32" (5.5 mm) of the screw exposed.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 65 °F
and 75 °F (18° 24 °C). DO NOT charge the battery pack in
an air temperature below +40 °F (+4.5 °C), or above +105 °F
(+40.5°C). This is important and will prevent serious damage to
the battery pack.
2. The charger and battery pack may become warm to the touch
while charging. This is a normal condition, and does not indicate
a problem. To facilitate the cooling of the battery pack after use,
Page dimensions: 8.5 x 5.5 inches
8
English
FIG. 2
A
B
C
D
E
F
G
H
I
J
WARNING: Burn hazard. Do not submerge the battery pack in
any liquid or allow any liquid to enter the battery pack. Never attempt
to open the battery pack for any reason. If the plastic housing of the
battery pack breaks or cracks, return to a service center for recycling.
Storage Recommendations
1. The best storage place is one that is cool and dry, away from
direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully charged
battery pack in a cool dry place out of the charger for optimal
results.
NOTE: Battery packs should not be stored completely depleted of
charge. The battery pack will need to be recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (Fig. 2)
WARNING: Never modify the apparatus or any part of it. Damage
or personal injury could result.
A. Power button
B. LED indicator light
C. Bluetooth
®
pairing button
D. Pause button
E. Volume buttons +/-
F. AUX audio port
G. USB power port
H. AC power input
I. Battery port
J. Carry handle
INTENDED USE
This D
EWALT Bluetooth
®
speaker is designed to play/stream audio
via a wireless Bluetooth
®
connection or wired connection to a mobile
phone or other audio device.
DO NOT use under wet conditions or in presence of flammable
liquids or gases.
Page dimensions: 8.5 x 5.5 inches
9
English
To remove the battery pack from the apparatus, press the release
button and firmly pull the battery pack out of the port. Insert it into the
charger as described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 5)
Some D
EWALT battery packs include a
fuel gauge which consists of three green
LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold
the fuel gauge button (K). A combination
of the three green LED lights will illuminate
designating the level of charge left. When
the level of charge in the battery is below
the usable limit, the fuel gauge will not
illuminate and the battery will need to be
recharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate apparatus functionality and is
subject to variation based on product components, temperature and
end-user application.
For more information regarding fuel gauge battery packs, please
call 1-800-4-D
EWALT (1-800-433-9258) or visit our website
www.dewalt.com.
K
FIG. 5
DO NOT let children come into contact with the apparatus.
Supervision is required when inexperienced operators use this
apparatus.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn
apparatus off and unplug or remove the battery pack before
making any adjustments or removing/installing attachments or
accessories.
The speaker can operate off
FIG. 3
H
of DC power (a battery pack)
or with an AC power adapter
plug. To power the speaker
using the AC adapter, plug
the adapter into the
appropriate outlet and
connect it to the speaker via
the AC power input (Fig. 3,
H). Battery pack will not
charge when AC adapter is
plugged in.
Installing and Removing
the Battery Pack (Fig. 4)
FIG. 4
I
L
NOTE: For best results, make sure your
battery pack is fully charged.
To install the battery pack (L) into the
battery port (I), align the battery pack
with the rails on the sides of the port and
slide the battery in until the battery pack
is firmly seated. Be sure that it does not
disengage.
Page dimensions: 8.5 x 5.5 inches
10
English
Upon initial use, the speaker will require pairing. To pair speaker to
a Bluetooth
®
device refer to Pairing Speaker with a Bluetooth
®
Audio Device.
LED SPEAKER STATUS INDICATOR
LED indicator Status/Mode
Steady blinking (half
second interval)
Speaker is unpaired or in connecting
mode.
Rapid Blinking Speaker is in pairing mode and
discoverable by your device.
Solid light Speaker is connected with a device.
No light Speaker has timed out and/or is off.
FIG. 7
C
E
E
D
B
A
Functionality (Fig. 6, 7)
Audio can be played through the speaker via a wireless Bluetooth
®
connection to a compatible Bluetooth
®
device or by connecting audio
device or mobile phone using a 1/8' (3.5 mm) audio cable to the
audio port (F).
OR
OU
O
FIG. 6
F
OR
POWERING THE SPEAKER ON AND OFF (FIG. 7)
Pressing the power button (A) will turn the speaker on or off. When
turned on, the LED indicator (B) will indicate the speaker's status.
Page dimensions: 8.5 x 5.5 inches
11
English
ADJUSTING THE SPEAKER VOLUME (FIG. 7)
The speaker volume can be decreased or increased by using the
corresponding volume buttons (E). Pressing the "VOL +" button
increases the volume. Pressing the "VOL-" decreases the volume.
The pause button (D) can silence the speaker at any volume by being
pressed once. Pressing the pause button again will unpause the
speaker. The speaker will emit a tone when the maximum or minimum
volume is reached.
TIMEOUT FUNCTIONALITY (FIG. 1)
To conserve battery life the speaker is designed to power off
automatically after an hour of inactivity. This inactivity could be due to
the device being unpaired for an hour or in the case of the Bluetooth
®
connection being broken for the same period of time. If the speaker
powers off due to inactivity of any kind refer to Connecting a
Previously Paired Bluetooth
®
Audio Device.
NOTE: Optimum Bluetooth
®
streaming range is roughly 30 ft
(9 m) (line of sight) to the speaker but distances up to 100 feet
(30 m) are possible. Physical obstacles, other wireless devices or
electromagnetic devices may affect the connection quality.
If Bluetooth
®
connection is lost due to exceeding time of separation,
exceeding the optimum distance, obstacles or otherwise, reconnecting
your device with the speaker may be necessary.
CHARGING A CELL PHONE OR AUDIO DEVICE VIA USB
(FIG.1)
Your audio device or mobile phone can be charged using the USB
power port (G) on the speaker. This charging is possible when unit is
on, running off of AC plug power or the battery pack.
PAIRING SPEAKER WITH A BLUETOOTH
®
AUDIO DEVICE
(FIG.6, 7)
1. Place the speaker and the Bluetooth
®
audio source within 3.3'
(1m) of each other.
2. Turn speaker on by pressing the power button (A). The LED (B)
will light solid for 4 seconds to indicate the apparatus powered on
successfully and then go into a half second interval blink pattern.
3. Press the Bluetooth
®
pairing button (C). The LED indicator light
blinks rapidly indicating the speaker is in pairing mode and is
discoverable by your Bluetooth
®
device.
4. Confirm pairing on your device. (Please consult your device's
instruction manual for specific pairing instructions.)
NOTE: If pairing is not confimed within 2 minutes, the LED will
stop flashing and the speaker will return to half second interval
blink pattern.
5. Once pairing is successful the LED indicator (B) will turn solid
and the speaker will emit a short tone. The speaker will now play
music from your device.
CONNECTING A PREVIOUSLY PAIRED BLUETOOTH
®
AUDIO
DEVICE (FIG. 1, 7)
If a Bluetooth
®
device has been previously paired to the speaker
it should automatically reconnect when speaker is powered on.
After 4 seconds the speaker will go into connecting mode. This is
indicated by the LED (B) blinking steady. Once the previously paired
Bluetooth
®
device is recognized and connected, the LED will go
solid. If connection does not occur and you are unable to stream
music please follow the instructions for Pairing Speaker with a
Bluetooth
®
Audio Device.
Page dimensions: 8.5 x 5.5 inches
12
English
Accessories
WARNING: Since accessories, other than those offered by
D
EWALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk of
injury, only D
EWALT recommended accessories should be used with
this product.
Recommended accessories for use with your tool are available at
extra cost from your local dealer or authorized service center. If you
need assistance in locating any accessory, please contact D
EWALT
Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286,
call 1-800-4-D
EWALT (1-800-433-9258) or visit our website: www.
dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment (including brush inspection and replacement) should
be performed by a D
EWALT factory service center, a DEWALT
authorized service center or other qualified service personnel. Always
use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRANTY SERVICE: Registering your product will help you
obtain more efficient warranty service in case there is a problem
with your product.
CONFIRMATION OF OWNERSHIP: In case of an insurance
loss, such as fire, flood or theft, your registration of ownership will
serve as your proof of purchase.
Important Bluetooth
®
Speaker Notes
1. When receiving a phone call on a mobile phone which is
streaming to the Bluetooth
®
speaker, music playback stops. After
phone call is finished, music resumes playing.
PHONE CALL AUDIO THROUGH BLUETOOTH SPEAKER
Depending on your device it may be possible to have the audio
from a phone call play through the Bluetooth
®
Speaker. This
is dependent on the device and the way the device's settings
are configured. Please refer to the device's owner’s manual for
capability and settings information.
2. Due to the characteristics of Bluetooth
®
technology, the sound
heard through the Bluetooth
®
speaker is slightly delayed from the
sound played on your audio device or mobile phone while talking
on a phone call or streaming music.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn
apparatus off and unplug or remove the battery pack before
making any adjustments or removing/installing attachments or
accessories.
Cleaning
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the apparatus. These chemicals
may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the apparatus; never immerse any part of the apparatus into
a liquid.
Page dimensions: 8.5 x 5.5 inches
13
English
FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-800-4-D
EWALT (1-800-433-
9258) for a free replacement.
FOR YOUR SAFETY: Registering your product will allow us to
contact you in the unlikely event a safety notification is required
under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials
or workmanship for three years from the date of purchase. This
warranty does not cover part failure due to normal wear or tool
abuse. For further detail of warranty coverage and warranty repair
information, visit www.dewalt.com or call 1-800-4-D
EWALT (1-800-
433-9258). This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights
which vary in certain states or provinces.
In addition to the warranty, D
EWALT tools are covered by our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts caused by
normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your
D
EWALT Power Tool, Laser, or Nailer for any reason, you can return
it within 90 days from the date of purchase with a receipt for a full
refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold
in Latin America. For products sold in Latin America, see country
specific warranty information contained in the packaging, call the local
company or see website for warranty information.
Page dimensions: 8.5 x 5.5 inches
45
Español
ESPECIFICACIONES
DCR006 12/20 V Máx*
SOLAMENTE PARA PROPÓSITO DE MÉXICO:
IMPORTADO POR: D
EWALT INDUSTRIAL TOOL CO. S.A. DE C.V.
AVENIDA ANTONIO DOVALI JAIME, # 70 TORRE B PISO 9
COLONIA LA FE, SANTA FÉ
CÓDIGO POSTAL : 01210
DELEGACIÓN ALVARO OBREGÓN
MÉXICO D.F.
TEL. (52) 555-326-7100
R.F.C.: BDE810626-1W7
Para servicio y ventas consulte
“HERRAMIENTAS ELECTRICAS”
en la sección amarilla.
AMÉRICA LATINA: Esta garantía no se aplica a los productos que
se venden en América Latina. Para los productos que se venden
en América Latina, debe consultar la información de la garantía
específica del país que viene en el empaque, llamar a la compañía
local o visitar el sitio Web a fin de obtener esa información.
REEMPLAZO GRATUITO DE LAS ETIQUETAS DE
ADVERTENCIAS: Si sus etiquetas de advertencia se vuelven
ilegibles o faltan, llame al 1-800-433-9258 (1-800-4-D
EWALT) para
que se le reemplacen gratuitamente.
DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286
(JUN14) Part No. N409555 DCR006 Copyright © 2014 D
EWALT
The following are trademarks for one or more D
EWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array
of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
* Maximum initial battery voltage (measured without a workload) is 20 volts. Nominal voltage is 18.
* La tension initiale maximum du bloc-piles (mesurée à vide) est de 20 volts. La tension nominale est de 18.
* El máximo voltaje inicial de la batería (medido sin carga de trabajo) es 20 voltios. El voltaje nominal es de 18.
DEWALT Battery and Charger Systems
Chargers/Charge Time (Minutes) – Chargeurs/Durée de charge (Minutes) – Cargadores de baterías/Tiempo de carga (Minutos)
Battery
Cat #
Output
Voltage
120 Volts 12 Volts
DC011 DC022 DC9000 DC9310 DC9320 DCB095 DCB100 DCB101 DCB102 DCB103 DCB106 DCB107 DCB112 DW911 DW9106 DW9107 DW9108 DW9116 DW9117 DW9118 DW9216 DW9226 DW0246 DCB119 DW0249 DW9109 DC9319
DC9360
36XX45XXXXXXX X X XXXXXXXXX X XXXXX
DCB361
36XX45XXXXXXX X X XXXXXXXXX X XXXXX
DC9280
28XX60XXXXXXX X X XXXXXXXXX X XXXXX
DW0242
24XXXXXXXXXX X X XXXXXXXXX X60X60XX
DCB200
20 X X X X X X X 60 60 60 140 140 90 X X X X X X X X X X 90 X X X
DCB201
20 X X X X X X X 30 30 30 70 70 45 X X X X X X X X X X 45 X X X
DCB203
20 X X X X X X X 35 35 35 90 90 60 X X X X X X X X X X 60 X X X
DCB204
20 X X X X X X X 70 70 70 185 185 120 X X X X X X X X X X 120 X X X
DCB205
20 X X X X X X X 90 90 90 240 240 150 X X X X X X X X X X 150 X X X
DCB207
20 X X X X X X X 30 30 30 60 60 40 X X X X X X X X X X X X X X
DC9096
18 60 60 X 60 60 X X X X 60 X X X 60 X X 60 60 20 X 60 130 X X X 60 60
DC9099
18 45 45 X 45 45 X X X X 45 X X X 45 X X 45 45 15 X 45 95 X X X 45 45
DC9180
18XXX6060XXXX60XXXXXXXXXXXXXXXX60
DC9181
18XXX3030XXXX30XXXXXXXXXXXXXXXX30
DW9096
18 60 60 X 60 60 X X X X 60 X X X 60 X X 60 60 20 X 60 130 X X X 60 60
DW9098
18 30 30 X 30 30 X X X X 30 X X X 30 X X 30 30 12 X 30 60 X X X 30 30
DW9099
18 45 45 X 45 45 X X X X 45 X X X 45 X X 45 45 15 X 45 95 X X X 45 45
DC9091
14.4 60 60 X 60 60 X X X X 60 X X X 60 90 60 60 60 20 115 60 115 X X X 60 60
DC9094
14.4 45 45 X 45 45 X X X X 45 X X X 45 60 45 45 45 15 90 45 90 X X X 45 45
DW9091
14.4 45 45 X 45 45 X X X X 45 X X X 45 60 45 45 45 15 90 45 90 X X X 45 45
DW9094
14.4 30 30 X 30 30 X X X X 30 X X X 30 45 30 30 30 12 60 30 60 X X X 30 30
DCB120
12XXXXX X40303030X6045XXX X X X X X X X45X XX
DCB127
12 X X X X X X X 35 35 35 X 90 60 X X X X X X X X X X 60 X X X
DC9071
12 60 60 X 60 60 X X X X 60 X X X 60 90 60 60 60 20 115 60 115 X X X 60 60
DW9050
12XXXXXXXXXX X X XX40XXXXX X X XXXXX
DW9071
12 45 45 X 45 45 X X X X 45 X X X 45 60 45 45 45 15 90 45 90 X X X 45 45
DW9072
12 30 30 X 30 30 X X X X 30 X X X 30 45 30 30 30 12 60 30 60 X X X 30 30
DW9048
9.6XXXXXX XXXXX X XX40XXXXXX X XXXXX
DW9061
9.6 45 45 X 45 45 X X X X 45 X X X 45 60 45 45 45 15 90 45 90 X X X 45 45
DW9062
9.6 30 30 X 30 30 X X X X 30 X X X 30 45 30 30 30 12 60 30 60 X X X 30 30
DCB080
8XXXXX60XXXXX X XXXXXXXXX X XXXXX
DW9057
7.2 30 30 X 30 30 X X X X 30 X X X 30 45 30 30 30 12 60 30 60 X X X 30 30
“X” Indicates that the battery pack is not compatible with that specific charger.
“X” indique que le bloc-piles n’est pas compatible avec ce chargeur.
Una “X” indica que el paquete de baterías no es compatible con ese determinado cargador.
All charge times are approximate. Actual charge time may vary. Read the instruction manual for more specific information.
Les durées de charge sont approximatives; la durée de charge rélle peut varier. Lire le manuel d’utilisation pour obtenir des renseignements plus précis.
El tiempo de duración de carga es aproximado; la duración de carga real puede variar. Lea el manual de instrucciones para obtener información más precisa.
Page dimensions: 8.5 x 5.5 inches
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

DeWalt DCR006 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages