Essick EP9 500 Care & Use Manual

Category
Dehumidifiers
Type
Care & Use Manual

This manual is also suitable for

READ AND SAVE THESE INSTRUCTIONS
OWNER’S
CARE
&
USE
MANUAL
MODELS:
EP9 500
EP9R 500 with Remote
EP9 700
Digital Control
Variable Speed
Auto Humidistat
Automatic Shutoff
Quiet Setting for Nighttime use
EP Series
French and Spanish
Instructions included.
Se incluyen instrucciones
En Espol y Francés.
Directives en Français et en espagnol compris
SAVE THE ENVIRONMENT
RECYCLE APPROPRIATE MATERIALS
1B72504 4/2013 Printed in China
EVAPORATIVE
HUMIDIFIER
2
General Safety Instructions
READ BEFORE USING YOUR HUMIDIFIER
DANGER: means if the safety information is not followed someone will be seriously
injured or killed.
WARNING: means if the safety information is not followed someone could be
seriously injured or killed.
CAUTION: means if the safety information is not followed someone may be injured.
1. To reduce the risk of fire or shock hazard, this humidifier has a polarized plug
(one blade is wider than the other.) Plug humidifier directly into a 120V, A.C.
electrical outlet. Do not use extension cords. If the plug does not fully fit
into the outlet, reverse plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
2. Keep the electric cord out of traffic areas. To reduce the risk of fire hazard, never
put the electric cord under rugs, near heat registers, radiators, stoves or heaters.
3. Always unplug the unit before moving, cleaning or removing the fan assembly
section from the humidifier, or whenever it is not in service.
4. Keep the humidifier clean.
5. Do not put foreign objects inside the humidifier.
6. Do not allow unit to be used as a toy. Close attention is necessary when used by
or near children.
7. To reduce the risk of electrical hazard or damage to humidifier, do not tilt, jolt or
tip humidifier while unit is running.
8. To reduce the risk of damage to humidifier, unplug when not in use.
9. To reduce the risk of accidental electrical shock, do not touch the cord or controls
with wet hands.
10. To reduce the risk of fire, do not use near an open flame such as a candle or
other flame source.
WARNING: For your own safety, do not use humidifier if any parts are
damaged or missing.
WARNING: To reduce risk of fire, electric shock, or injury always unplug before
servicing or cleaning.
CAUTION: If a plant is placed on the pedestal, ensure unit is unplugged when
watering the plant. Ensure no water is poured onto the control panel when
watering the plant. If water enters the electronic control panel, damage may
result. Ensure control panel is entirely dry before use.
WARNING: To reduce the risk of fire or shock hazard, do not pour or spill water
into control or motor area. If controls get wet, let them dry completely and have
unit checked by authorized service personnel before plugging in.
3
How Your
Humidifier Works
Once the wick becomes
saturated, air is drawn in,
passes through the wick
and moisture is absorbed
into the air.
All evaporation occurs in
the humidifier so any
residue remains in the
wick. This natural process
of evaporation creates no
white dust like some other
humidifiers.
Dry air is drawn into the
humidifier though the back
and moisturized as it
passes through the
evaporative wick. It is then
fanned out into the room.
Description
EP9 Series / EP9R†
*Output per 24 hrs
9 + gallons
Capacity of Unit
3.5 gallons
Sq. ft. coverage
2000-2800 *
Fan Speeds
Variable (9)
Replacement Wick
No. 1043
Automatic Humidistat
Yes
Controls
Digital (w/ Remote)
ETL Listed
Yes
Volts
120
Hertz
60
Watts
70
IMPORTANT:
Water damage may result
if condensation starts to
form on windows or walls.
Humidity SET point should
be lowered until
condensation no longer
forms. We recommend
room humidity levels do
not exceed 50%.
* Output based on 8’
ceiling. Coverage may
vary due to tight or
average construction.
Notes On Location:
Do NOT position the unit directly in front of a hot air duct or radiator. Do NOT place
on soft carpet.
Direct air flow away from thermostat and hot air registers, and position humidifier
next to an inside wall. Unit should not be placed where cold air from outside walls or
warm air from a hot air register blows directly on it.
Place the humidifier on a level place at least 2 inches away from the wall or curtains
Position the humidifier where the most humidity is needed or where the most air will
be circulated throughout the house such as near a cold air return. If the unit is
positioned close to a window, condensation may form on the window pane. If this
occurs the unit should be repositioned in another location.
4
Assembly
CASTERS
1. Lift chassis off of base and set aside.
2. Remove float and wick/wick retainer from base. Turn the empty base upside
down. Insert each caster stem into a caster hole on each corner of the humidifier
bottom. The casters should fit snugly and be inserted until the stem shoulder
reaches the cabinet surface.
3. Turn the base right side up.
EVAPORATIVE WICK
4. Ensure the 1043 Superwick is
installed in the two-part wick
retainer base in the base of the
humidifier
5. Position the chassis over the base
frame and press it onto the base
firmly until it is in place.
6. Ensure the chassis is placed on the
base with the float facing forward.
FILLING INFORMATION
Open the fill door on the front of the unit. Insert funnel into open fill door. Using a
pitcher, carefully pour water to the MAX FILL level on the wick frame.
NOTE: On initial fill up, it will take approximately 20
minutes for the unit to become ready for operation,
since the wick must become saturated. Subsequent
fillings will take approximately 12 minutes, since the
wick is already saturated.
After the filling process is complete, and the wick is
saturated, the unit is ready for use.
7. Plug cord into wall receptacle. Your humidifier is
now ready for use. The humidifier should not be
near any heat registers. Place the unit at least
TWO inches away from any walls or curtains.
Unrestricted airflow into the unit will result in the
best efficiency and performance.
Controls and Operation
This unit has a digital control panel
that allows you to adjust fan speed
and humidity level, as well as view
information on the status of the unit.
The display will also indicate if the
optional Remote Control (EP9R
500 only) is in use at the time.
CAUTION: If a plant is placed on the pedestal, ensure no water is poured onto the
control panel when watering the plant. If water enters the electronic control panel,
damage may result. If controls get wet, let them dry completely and have unit
checked by authorized service personnel before plugging in.
5
1. The digital controller has a display that provides information on the status of the unit.
Depending on which function is being accessed, it displays relative humidity, fan
speed, set humidity and indicates when the unit is out of water.
FAN SPEED
2. The Speed button controls the variable
speed motor. Nine speeds provide
precise fan control. Press the power
button and select fan speed: F1
through F9 proceeding from low to
high speed. The fan speed will display
on the control panel as the speeds are
stepped through.
NOTE: When excessive condensation exists, a lower fan speed setting is recommended.
HUMIDITY CONTROL
NOTE: Allow 10 to 15 minutes for the
humidistat to adjust to the room when
setting up the unit for the first time.
NOTE: The EP9 / EP9R Series has
an automatic humidistat located on
the cord that measures the relative humidity
in the room. When the selected humidity
level drops 3% below the relative humidity,
the humidifier cycles on and off as required
to maintain the selected setting.
3. At initial startup the relative humidity of the room will be displayed.
Each successive push of the Humidity Control Button will increase the setting in
5% increments. At 65% set point, the unit will operate continuously
OTHER FEATURES / INDICATIONS
4. This humidifier has a check filter reminder timed to appear after 720
hours of operation. When the Check Filter (CF) message is
displayed, disconnect the power cord and check the condition of the
filter. The CF function is reset after plugging the unit back in.
5. When the unit is out of water, a flashing F will display on the display panel.
AUTO DRYOUT
At this time the unit will automatically switch into AUTO DRY OUT
MODE and continue to run on the lowest speed until the filter is
completely dry. The fan will shut off leaving you with a dry humidifier
that is less prone to mold and mildew.
If AUTO DRY OUT MODE is not desired, refill the humidifier with
water and the fan will return to the set speed.
6
If your unit has the remote control, or if you have purchased the remote control, Model 1999, you
have the option of controlling your humidifier functions from a distance.
To Turn the Remote on:
With both the humidifier and remote control OFF,
Press the I/O button on the remote control once.
This turns the humidifier ON and enables the
remote control to operate all the functions of the
humidifier.
(The humidifier control panel will display EC, for
External Control)
Press the respective humidity and Fan Speed
buttons to adjust the settings on the remote, just
as you would the actual humidifier.
The default setting for temperature readout is
Fahrenheit (F). If you prefer degrees Celsius (C),
press the I/O button one more time to use that unit
of measure.
Pressing the I/O button one more time will turn
both the Remote Control and the Humidifier OFF.
If the Humidifier is already on and operating when the I/O button on the remote is pressed,
command of the humidifier transfers to the Remote, and reverts to the settings last used with the
remote. You can readjust the settings as desired.
If the controls on the humidifier are used while the Remote Control is in command, control will
revert to the humidifier, and the settings will revert to those last used on the humidifier control
panel. The remote control will remain on until turned off.
REMOTE CONTROL INSTRUCTIONS (EP9R 500)
USING THE REMOTE CONTROL
When the remote is in control, the display on the humidifier will read EC (for
External Control).
The humidity and speed buttons operate the same way as their counterparts
on the unit.
The fan speed and humidity setting will display on the control panel as you
adjust them.
The default measure for temperature is Fahrenheit (°F), but pressing the I/O
button a second time will change to Celsius (°C)
Periodically the remote performs a frequency check and will be unresponsive
to input. Wait 5 seconds and try your input again.
7
Wick Replacement
The EP9 / EP9R Series uses the 1043 Super Wick. Always use the original Essick
brand wick to maintain your unit and maintain your warranty.
1. First, remove any items on top of the pedestal and remove the natural stone tile
and place in a safe location.
2. Lift chassis up off the base to reveal the wick, wick retainer and float.
3. Remove the wick and retainer assembly. Separate the two-part wick retainer.
4. Remove the old wick, drain excess water and discard.
5. Place new Essick 1043 wick into front side of the wick retainer and snap the
larger, back section into place.
6. Then place the assembly into the base, aligning it with the built-in guides.
8
Care and Maintenance
CAUTION: Disconnect power before filling, cleaning or servicing unit. Keep grille dry
at all times.
Cleaning your humidifier regularly helps eliminate odors and bacterial and fungal
growth. Ordinary household bleach is a good disinfectant and can be used to wipe
out the humidifier base after cleaning. We recommend cleaning your humidifier at
least once every two weeks to maintain optimum environmental conditions for your
home.
We also recommend using Essick Air Bacteriostat Treatment each time you refill
your humidifier to eliminate bacterial growth. Add bacteriostat according to the
instructions on the bottle. Please call 1-800-547-3888 to order Bacteriostat
Treatment reference part number 1970.
1. Remove any items from the pedestal top. Remove natural stone tile and place
in safe location. Turn off unit completely and unplug from outlet.
2. Lift off chassis and set aside.
3. Carry base to cleaning basin. Lift wick and retainers from the base allowing the
water to drain. Rinse wick under fresh water only. Do not use soap, detergent,
or any other cleaners on the wick. Leave in sink to drain.
REMOVING SCALE
4. Empty the water from the base. Fill base with water and add 8 oz. (1 cup) of
white vinegar. Let stand 20 minutes. Then empty solution.
5. Dampen a soft cloth with white vinegar and wipe out base to remove scale.
Rinse the entire water reservoir area thoroughly with fresh water to remove
scale and cleaning solution before disinfecting.
DISINFECTING UNIT
6. Fill base to with water and add 1 teaspoon of bleach. Wipe interior surfaces
with this solution. Let solution stay for 20 minutes, then rinse with water until
bleach smell is gone. Dry with clean cloth. The outside of the unit may be wiped
down with a soft cloth dampened with fresh water.
7. Replace the chassis onto the base and refill unit through the pour-fill spout.
SUMMER STORAGE
Although the pedestal humidifier is attractive enough to be kept out year round, if
you choose to put the unit away for the summer, ensure proper care is taken to
protect the humidifier during storage. We do not recommend removing the stone tile
from the unit’s top. We recommend storing the optional remote control (with batteries
removed) with the humidifier for easy access when the humidifier is used again.
Clean unit as outlined in Care & Maintenance section.
1. Discard used wick and any water in the base and allow to dry thoroughly before
storage. Do not store with water inside the base.
2. Do not store unit in an attic or other high-temperature area, as damage will
occur.
3. Install new filter at beginning of season.
9
Parts List for EP9/EP9R Series
Parts and accessories may be ordered by calling 1-800-547-3888. Always order
by part number, not key no. Please have model number of humidifier available
when calling.
Replacement Parts Available For Purchase
Key
No.
Description
Part Number
EP9(R) 500
EP9 700
1
Deflector/Vent
1B71973
1B72219
2
Funnel
1B72282
1B72282
2
Float
1B71971
1B71971
3
Float Retainer
1B71972
1B71972
4
Casters (4)
1B5460070
1B5460070
5
Wick support assy.
1B72081
1B72081
6
Wick
1043
1043
7
12” x 12” x 3/8” Natural Stone Tile
1B72077
1B72496
8
Remote Control
7V1999
NA
--
Owner’s Manual (Not pictured)
1B72120
1B72504
9
10
ESSICK AIR PRODUCTS
HUMIDIFIER WARRANTY
POLICY
EFFECTIVE APRIL 1, 2013
SALES RECEIPT REQUIRED AS PROOF OF
PURCHASE FOR ALL WARRANTY CLAIMS.
This product is warranted against defects in workmanship and materials as listed below:
One year from the date of sale on factory installed components.
Two years from the date of sale on motor and control.
Thirty (30) days on replacement components.
This warranty does not apply to filters or wicks which are customer replaceable parts.
This warranty applies only to the original purchaser of the product when it is purchased from
a reputable retailer/dealer.
This warranty does not apply to damage from accident, misuse, alterations, unauthorized
repairs, unauthorized use, mishandling, unreasonable use, abuse, including failure to perform
care and maintenance as listed in the owner’s manual, normal wear and tear, nor where the
connected voltage is more than 5% above the nameplate voltage, nor to the equipment or
products being improperly installed or wired or maintained in violation of this Owner’s Manual.
Alterations include the substitution of name brand components including, but not limited to
wicks and bacteria treatment.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. THIS IS THE SOLE AND
EXCLUSIVE WARRANTY GIVEN BY MANUFACTURER WITH RESPECT TO THE PRODUCTS
AND, TO THE MAXIMUM EXTENT PERMITTED BY LAW, IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES AND CONDITIONS, EXPRESSED OR IMPLIED, ARISING BY
OPERATION OF LAW OR OTHERWISE. INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
No employee, agent, dealer or other person is authorized to give any warranties or conditions
on behalf of the manufacturer. The customer shall be responsible for all costs incurred in the
removal or reinstallation and shipping of the product for repairs.
Within the limitations of this warranty, purchaser with inoperative units should contact
customer service @ 800-547-3888 for paperwork and instructions on the return of the unit
for replacement. A copy of the sales receipt is required before authorization to return a
unit for repair is approved. The manufacturer will replace the chassis, at its discretion, with
return freight paid by the manufacturer and that TO THE MAXIMUM EXTENT PERMITTED BY
LAW, THE MANUFACTURER IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND,
INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGE OR LOSS OF PROFITS OR
REVENUES.
This warranty will be null & void if purchaser attempts to repair or replace any parts
which are mechanical or electrical.
The warranty gives the customer specific legal rights, and the customer may also have
other rights which vary from province to province, or state to state.
32
Essick Air Products
5800 Murray Street
Little Rock, AR. 72209
www.essickair.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Essick EP9 500 Care & Use Manual

Category
Dehumidifiers
Type
Care & Use Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages