Korg TM-50C Owner's manual

Page is loading ...

2

Precautions

Location

Using the unit in the following locations can

result in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

• Close to magnetic ﬁelds

Power supply

Be sure to turn the power switch to OFF when the

unit is not in use. Remove the battery in order to

prevent it from leaking when the unit is not in use

for extended periods.

Interference with other electrical devices

Radios and televisions placed nearby may experi-

ence reception interference. Operate this unit at a

suitable distance from radios and televisions.

Handling

To avoid breakage, do not apply excessive force

to the switches or controls.

Care

If the exterior becomes dirty, wipe it with a clean,

dry cloth. Do not use liquid cleaners such as

benzene or thinner, or cleaning compounds or

ﬂammable polishes.

Keep this manual

After reading this manual, please keep it for later

reference.

Keeping foreign matter out of your

equipment

Never set any container with liquid in it near this

equipment. If liquid gets into the equipment, it

could cause a breakdown, ﬁre, or electrical shock.

Be careful not to let metal objects get into the

equipment.

3

THE FCC REGULATION WARNING (for USA)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-

ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

● Consult the dealer or an experienced radio/TV technician for help.

Unauthorized changes or modiﬁcation to this system can void the user’s authority to operate this

equipment.

4

Notice regarding disposal (EU only)

When this “crossed-out wheeled bin”

symbol is displayed on the product,

owner’s manual, battery, or battery

package, it signiﬁes that when you

wish to dispose of this product, manu-

al, package or battery you must do so

in an approved manner. Do not

discard this product, manual, package

or battery along with ordinary household

waste. Disposing in the correct manner will

prevent harm to human health and potential

damage to the environment. Since the correct

method of disposal will depend on the

applicable laws and regulations in your

locality, please contact your local

administrative body for details. If the battery

contains heavy metals in excess of the

regulated amount, a chemical symbol is

displayed below the “crossed-out wheeled

bin” symbol on the battery or battery

package.

IMPORTANT NOTICE TO CONSUMERS

This product has been manufactured accord-

ing to strict speciﬁcations and voltage require-

ments that are applicable in the country in

which it is intended that this product should

be used. If you have purchased this product

via the internet, through mail order, and/or

via a telephone sale, you must verify that this

product is intended to be used in the country

in which you reside.

WARNING: Use of this product in any country

other than that for which it is intended could

be dangerous and could invalidate the manu-

facturer’s or distributor’s warranty. Please

also retain your receipt as proof of purchase

otherwise your product may be disqualiﬁed

from the manufacturer’s or distributor’s war-

ranty.

All product names and company names are the

trademarks or registered trademarks of their

respective owners.

5

Table of Contents

Main Features ................................. 6

Installing batteries ......................... 6

Using the stand ............................... 7

Parts of the TM-50 and what they do ...

7

Turning the power on/off ............... 8

To turn the power on ...........................8

Turning the tuner off ............................9

Turning off the metronome ...............9

Connections .................................... 9

If you want to connect an instru-

ment or contact mic etc ......................9

Connecting headphones ....................9

Using the tuner ............................. 10

Tuning while watching the meter

(Meter mode) ....................................... 10

Tuning to a reference tone (Sound

Out mode) ............................................. 11

Tuning using the reference tone and

meter (Sound Back mode)............... 12

Using the metronome .................. 13

Setting the tempo and time signa-

ture (Beat mode) ................................. 13

Using tap tempo ................................. 14

Using the tuner and metronome

simultaneously ............................. 15

Using the tuner and metronome

simultaneously .................................... 15

Backlight ....................................... 17

Speciﬁcations ................................ 17

6

Thank you for purchasing the Korg Combo

Tuner Metronome TM-50.

Main Features

With the TM-50 you can tune instruments

using the internal mic or by connecting them

to the INPUT jack.

You can use the tuner and metronome indi-

vidually or simultaneously.

Installing batteries

1.

Slide the baery compartment cover on

the back of the TM-50 in direction “a” as

shown in the illustration and li up the

cover in direction “b.”

2.

Insert the baeries, making sure to ob-

serve the correct polarity.

If the unit malfunctions try removing and

then reinstalling the baeries.

When the baeries become depleted, a

baery symbol will appear on the le

side of the display. When this occurs, it’s

time to replace the baeries.

7

Using the stand

You can use the stand provided on the back

of the TM-50 to tilt it back at an angle for easy

viewing.

Parts of the TM-50 and what they do

9

1

2

3

4

5 6 7 8

10 11

12

13

14

15

16

17

1.

TUNER ON button

2.

CALIB/NOTE

p

,

q

button

s

3.

SOUND button

4.

SOUND BACK button

5.

Backlight button

6.

Mic

8

7.

Speaker

8.

START/STOP button

9.

Tuning guide

10.

Volume

11.

METRONOME ON button

12.

BEAT

p

,

q

buttons

13.

TEMPO

p

,

q

buttons

14.

TAP TEMPO button

15.

PHONES jack

16.

INPUT jack

17.

Display

Reference pitch display

Note display

Tempo display

Beat display

Turning the power on/off

To turn the power on

Press either the TUNER ON buon or the

METRONOME ON buon and the power

will turn on.

When the TUNER ON buon is pressed,

the tuner starts in the Meter mode and

“

” will appear on the

display. When the METRONOME ON but-

ton is pressed, the metronome starts and

“

” will appear on the display.

The TM-50 can use the tuner and metronome

simultaneously.

The TUNER ON buon and the MET-

RONOME ON buon is designed lower

than other buons so that the power is

not turned on involuntarily when the

TM-50 is placed in your pocket or in a

9

bag. To turn the device on or o, push in

the power buon.

Turning the tuner off

When the tuner is in use, press the TUNER

ON buon to turn o the power. The tuner

will also turn o automatically if it’s not in

use for twenty minutes.

Turning off the metronome

When the metronome is in use, press the

METRONOME ON buon to turn o the

power. The metronome will also turn o au-

tomatically if not in use for twenty minutes.

Connections

If you want to connect an

instrument or contact mic etc

If you want to tune an instrument with a

pickup, such as an electric guitar, connect a

cable to your instrument, and plug the cable

into the TM-50’s INPUT jack.

The INPUT jack is only for a 1/4" mono

cable. Stereo (TRS) cables cannot be used.

If you want to tune your instrument using a

Korg contact mic (separately sold), plug the

contact mic into the TM-50’s INPUT jack.

If a device is not connected to the INPUT

jack, tuning will be performed by the

internal mic.

Connecting headphones

You can connect headphones with a 1/8"

mini-plug to the PHONES jack.

When plugged in, no sound will be heard

from the speaker. Use the volume control to

adjust the volume of the headphones output.

10

Using the tuner

Tuning while watching the meter

(Meter mode)

1.

Connect your instrument cable or contact

mic to the TM-50’s INPUT jack.

If a device is not connected to the

INPUT jack, tuning will be performed

by the internal mic.

2.

Press the TUNER ON buon.

“

” will appear at the top

of the display and the calibration (refer-

ence pitch) will be displayed below that.

3.

To change the calibration, press the

CALIB/NOTE

p

or

q

buon.

The calibration value increases and

decreases in units of 1 Hz. By pressing and

holding these buons, you can increase or

decrease the value continuously. This set-

ting is stored even when the power is o.

4.

Play a single note on your instrument.

The closest note to the input sound will

appear in the center of the display. Tune

your instrument to the correct pitch, so

that the desired note name appears.

If you’re using the internal mic, place

your instrument as close as possible

to the mic so that extraneous sound is

not picked up while tuning.

5.

While playing a single note on your

instrument, tune your instrument so that

the tip of the meter indicates “

q

” and

the center indicator of the tuning guide

is lit up.

The le tuning guide indicator will light

up if the pitch of your instrument is at,

and the right indicator will light up if the

11

pitch is sharp.

If you want to tune a just major third above

or a minor third above a certain note, use

the “

” (-13.7 cent) or “ ” (+15.6 cent)

marks on the meter.

Tuning to a just major third above or

a minor third above

If you want to tune to a just major third

above A (0 cent), tune your instrument so

that the note name indicator shows C and

the meter is at “

”.

If you want to tune to a minor third above

A (0 cent), tune your instrument so that

the note name indicator shows C and the

meter is at “

”.

Tuning to a reference tone (Sound

Out mode)

1.

Press the TUNER ON buon.

You will enter the Meter mode.

2.

Press the SOUND buon to select Sound

Out mode.

The reference tone is output from the

PHONES jack or speakers. Use the vol-

ume control to adjust the output volume.

3.

Press the CALIB/NOTE

p

or

q

buon

to select the note.

The output reference tone changes as fol-

lows.

C(C3)

n

C

♯

n

D

n

E

♭

n

E

n

F

n

F

♯

n

G

n

G

♯

n

A

n

B

♭

n

B

n

C(C4) ... C(C6)

n

C(C3)...

This seing is stored even when the

power is o.

4.

Tune the instrument according to the

reference tone.

5.

Press the SOUND buon again to return

to the Meter mode.

If connected to either the INPUT jack or

the PHONES jack, the Meter mode will

12

start simultaneously and you can tune

your instrument while viewing the meter.

Tuning using the reference tone

and meter (Sound Back mode)

This function can be used when you are

connected to either the INPUT jack or the

PHONES jack (or both).

1.

Press the TUNER ON buon.

You will enter the Meter mode.

2.

Press the SOUND BACK buon to enter

the Sound Back mode.

In the Sound Back mode, the reference

tone that’s closest to the tone of the input

instrument is output. Use the volume

control to adjust the volume.

“ ” will appear on the display.

If headphones are connected to the PHONES

jack, the input sound from the internal

mic or INPUT jack will be received and

the reference tone will be output from the

headphones.

If nothing is connected to the PHONES

jack, the input sound from the INPUT

jack is received and the reference tone is

output from the speakers.

If both the PHONES jack and the

INPUT jack are not connected, the

Sound Back mode will not function.

3.

Tune the instrument using the reference

tone and meter.

4.

If the SOUND BACK buon is pressed

again, you will return to the Meter mode.

13

Using the metronome

Setting the tempo and time

signature

1.

Press the METRONOME ON buon.

The pendulum of the metronome will ap-

pear on the display and “

” will appear above it.

2.

Press the TEMPO

p

or

q

buon to set

the tempo.

Press and hold the TEMPO

p

and

q

buons simultaneously for 1 second to

switch between Pendulum Step (pendu-

lum of a mechanical metronome) and Full

Step. If Pendulum Step is selected, “

”

will appear on the display.

Aer selecting “PENDULUM STEP” or

“FULL STEP”, press the TEMPO

p

,

q

buons to set the tempo. This seing is

remembered even when the power is o.

If you’ve selected “PENDULUM STEP”

Pressing the TEMPO

p

or

q

buon will

increase or decrease the tempo value by 1

step. The value will change continuously if

you hold down the buon.

30

n

32

n

34 ... 88

n

92

n

96 ... 232

n

240

n

252

n

30 ...

If you’ve selected “FULL STEP”

Pressing the TEMPO

p

or

q

buon will

increase or decrease the tempo value by 1

step. The value will change continuously

if you hold down the buon.

30

n

31

n

32 ... 250

n

251

n

252

n

30 ...

3.

Press the START/STOP buon to start

the metronome.

The metronome pendulum will swing

from le to right according to the tempo

and the TAP TEMPO buon will blink

according to the tempo also.

14

4.

If you want to change the time signature,

press the BEAT

p

or

q

buons to make

your selection.

The time signature will change as follows.

Press the BEAT

p

or

q

buons:

n

0

n

1 ...

9 (9 beats)

n

(Duplet)

n

(Triplet)

n

(Triplet without the center beat)

n

(Quadruplet)

n

(Quadruplet

without the center beat)

n

0 ...

5.

Play along with the metronome tempo.

6.

To stop the metronome, press the

START/STOP buon.

Using tap tempo

The tap tempo that you input will be dis-

played as a BPM (Beats Per Minute) value.

1.

Press the METRONOME ON buon.

The pendulum of the metronome will appear

on the display and “

”

will

appear above it.

2.

Press the TAP TEMPO buon several

times at regular intervals at the tempo

that you want.

The TM-50 detects the interval used when

pressing the buon and displays it as a

BPM (Beats Per Minute) value, and it will

be set as the tempo.

While the tempo is detected, “

” will

appear on the display.

When the BPM that has been detected by

the tap tempo is less than 30, “Lo” will

appear on the display and the tempo will

be set at “30.”

If the BPM detected by the tap tempo ex-

ceeds 252, “Hi” will appear on the display

and the tempo will be set at “252.”

3.

Press the START/STOP buon to start the

metronome.

The metronome pendulum will swing

from le to right according to the tempo

15

and the TAP TEMPO buon will blink

accordingly.

The tap tempo can also be input

while the metronome is in use.

4.

Play according to the tempo.

5.

To stop the metronome, press the START/

STOP buon.

Using the tuner and metronome

simultaneously

The TM-50 lets you use the tuner and metro-

nome simultaneously.

For more details on tuner and metronome op-

eration, please refer to the “Using the tuner”

and “Using the metronome sections.”

Using the tuner and metronome

simultaneously

For example, if you’re playing along with the

metronome and you notice that your instru-

ment is not tuned correctly, you can leave the

metronome running while you tune.

Proceed as follows.

1.

Press the METRONOME ON buon.

2.

Press the START/STOP buon to start

the metronome.

If necessary, specify the tempo and time

signature etc.

To set the tempo: use the TEMPO

p

,

q

buons.

To set the time signature: use the BEAT

p

,

q buons.

When using the tuner and metro-

nome simultaneously, you can’t select

16

“triplets”, “triplets without the center

beat”, “quadruplets” or “quadruplets

without the center beats” as the time

signature.

3.

Press the TUNER ON buon to enter

Meter mode.

The display will show the tuning meter.

The tempo of the metronome tempo is

indicated by the blinking of the TAP

TEMPO buon.

If you want to tune in Sound Out mode,

you should then press the SOUND but-

ton. To tune in the Sound Back mode,

press the SOUND BACK buon.

Tuning in Meter mode

When you play a single note on your in-

strument, the display will show the name

of the note that is closest to the pitch that

you played. Tune your instrument while

watching the meter and the tuning guide.

Tuning in Sound Out mode

Tune your instrument to the pitch that you

hear.

Tuning in Sound Back mode

Using the tone, tuning meter and tuning

guide, adjust your instrument.

4.

Aer tuning is complete, press the

TUNER ON buon and METRONOME

ON buon respectively to turn o the

tuner and metronome.

17

Backlight

When necessary, press the Backlight buon

“

” to set the backlight.

Each time the Backlight buon is pressed, you

can switch to So  Auto  O  So…

Soft: Low-intensity lighting to prevent bat-

tery consumption.

Auto: When a tone is input and the buon is

pressed, the backlight fully lights up.

If a sound is not input or a buon is not

pressed for 10 seconds, the backlight will

automatically change to the so seing

brightness.

Off: The backlight does not light up.

Speciﬁcations

Tuner section

Scale: 12 note equal temperament

Detection range*: C1 (32.70 Hz)–C8 (4186.01

Hz) for a sinewave

Reference tone: C3 (130.81 Hz)–C6 (1046.50

Hz) 3 octave

Tuning modes: Meter mode (AUTO),

Sound Out mode (MAN-

UAL), Sound Back mode

(AUTO)

Calibration range:

A4 = 410 Hz–480 Hz (1 Hz step)

Detection accuracy: Beer than ±1 cent

Sound accuracy: Beer than ±1 cent

Metronome section

Tempo range: 30–252 beats per minute

(bpm)

Tempo seing: PENDULUM STEP, FULL

STEP, TAP TEMPO

18

Time signatures: 0–9 beats, duplets, triplets,

triplets without the center

beat, quadruplets, quadru-

plets without the center beats

Tempo accuracy: ±0.3%

Main Speciﬁcations

Connectors: INPUT jack (1/4"mono),

PHONES jack (1/8" mini)

Speaker: Dynamic speaker (ø23 mm)

Power supply: Two AAA baeries (3V)

Baery life: Tuner ...

Approximately 70/44/26

hours (backlight: O/So/

Auto, A4 continuous input,

when using zinc-carbon

baeries)

Metronome ...

Approximately 55/35/22

hours backlight: O/So/

Auto, tempo 120, four

beats, maximum volume,

when using zinccarbon

baeries)

Dimensions:

111 (W) x 74 (D) x 18 (H) mm

/

4.37" (W) x 2.91" (D) x 0.71" (H)

Weight: 106 g (3.77 oz.) including

the provided baeries

Included items: Owner’s manual, two AAA

baeries

The calibration and reference tone of the

tuner as well as the tempo, beat, Pendulum

Step, Full Step and backlight seings of the

metronome are stored even when the power

is o. However when you exchange the

baeries, these seings will return to the fol-

lowing default values.

19

Default values:

Calibration = 440 Hz, Detection range = A4,

Tempo = 120,

Time signature = four beats

,

Tempo seing type = PENDULUM STEP,

Backlight seing = o

* Even if the pitch is within the range of de-

tection, the TM-50 may be unable to detect

the pitch if the sound contains numerous

overtones (such as the low and high notes

on an acoustic piano) or if the instrument

has a rapid decay.

Specications and appearance are subject to

change without notice for improvement.

Page is loading ...

Korg TM-50C Owner's manual

This manual is also suitable for

Korg TM-50C Owner's manual

in other languages

Related papers

Other documents