Metra TYTO-01 Installation guide

Category
Car kits
Type
Installation guide
TOYOTA AMPLIFIER INTERFACE
©Copyright 2010 Metra Electronics Corporation
1-800-221-0932
www.metraonline.com
TYTO-01
INSTALLATION INSTRUCTIONS
* IMPORTANT WARNING
THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST
BE CAREFULLY FOLLOWED. THE INSTRUCTIONS ARE WORDED IN SUCH A
MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COMPLETING
THESE TYPE OF ELECTRONIC INSTALLATIONS. IF YOU ARE UNCLEAR AS TO
WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE THAT YOU DO NOT UNDER-
STAND THE INSTRUCTIONS SO AS TO PROPERLY
AND SAFELY COMPLETE
THE INSTALLATION YOU SHOULD CONSULT A TECHNICIAN WHO DOES HAVE
THIS KNOWLEDGE AND UNDERSTANDING. FAILURE TO FOLLOW THESE
INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS
DESCRIBED COULD CAUSE HARM TO THE VEHICLE OR TO SAFETY
SYSTEMS ON THE VEHICLE. INTERFERENCE WITH CERTAIN SAFETY
SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL. IF YOU HAVE ANY
QUESTIONS IN THIS REGARD PLEASE CALL THE HELP LINE OR THE
METRA AT 1-800-221-0932 FOR ASSISTANCE.
TYTO-01 TYTO-01
* READ IMPORTANT WARNING INSIDE
BEFORE ATTEMPTING ANY INSTALLATION
• Cutting Tool • Tape Crimping Tool
TOOLS REQUIRED FOR INSTALLATION
REV. 11/22/10 INST-TYTO-01
APPLICATIONS
INTERFACE COMPONENTS
• TYTO-01
• 10 pin harness with rca’s
• 12 pin to 20 pin Toyota harness
Lexus
• ES330 2004-06
• ES350 2007-10
• ES300 2002-03
• GX470 2003-08
• IS350 2006-10
• IS300 2002-05
• IS250 2006-10
•LS460 2007-08
•LS430 2001-06
•LX470 2001-07
•RX300 2001-03
•RX330 2004-07
•RX350 2007-09
•RX400H 2006-08
•SC430 2002-09
Toyota
• 4Runner 2003-11
• Avalon 2011
• Camry/Camry Hybrid 2010-11
• Corolla 2005-10
• Highlander 2008-10
• Prius 2010
• Rav4 2004-10
• Sequoia 2005-2011
• Sienna 2004-2011
• Solara 2004-2009
• Tacoma 2005-2011
• Tundra 2004-2011
• Venza 2009-10
• Yaris 2007-10
The TYTO-01 is designed to interface an after-
market radio with factory amplifiers in the vehi-
cles listed below that have the JBL or JBL
Synthesis amplified sound system.
CONNECTIONS TO BE MADE ON THE 10
PIN HARNESS
1. Connect the Blue/White wire to the amp turn on wire of the aftermarket radio.
2. Connect the White rca to the left front rca output of the aftermarket radio.
3. Connect the Gray rca to the right front rca output of the aftermarket radio.
4. Connect the Green rca to the left rear rca output of the aftermarket radio.
5. Connect the Purple rca to the right rear rca output of the aftermarket radio.
CONNECTIONS TO BE MADE ON THE 12
PIN HARNESS
1. Connect the Yellow wire to the constant 12 volt/battery wire of the
aftermarket radio.
2. Connect the Red wire to the accessory/switched wire of the aftermarket radio.
3. Connect the Black wire to the ground wire of the aftermarket radio.
2
3
1
TYTO-01
AUDIO LEVEL CONTROL
When using the TYTO-01 with radios that have a really high pre-out voltage or a
really low pre-out voltage, some adjustments may be needed.
To do these follow these steps:
1. Find the potentiometer at the 12 pin harness end of the TYTO-01 interface.
2. With the radio at a moderate volume, use a small screwdriver and turn the
potentiometer clockwise to raise the input signal or counterclockwise to lower
the i
nput signal.
POTENTIOMETER
INSTALLING THE TYTO-01
1. With all the connections completed, plug the 10 pin and 12 pin harnesses into
the TYTO-01.
2. Plug the 20 pin Toyota harness into the vehicle side harness.
3. Plug the aftermarket harness into the aftermarket radio.
4. Cycle the key by turning the ignition on, then back off, then on again to test
the radio.
TESTING THE TYTO-01
1. With the ignition on turn the radio on to verify the radio works.
2. Listen to the music at a moderate level; if the music is too low or too distorted
see the Audio Level Control section.
POTENTIOMETER
  • Page 1 1
  • Page 2 2

Metra TYTO-01 Installation guide

Category
Car kits
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI