Dataram DRSX4450/8GB Datasheet

Dataram
Brand
Dataram
Model
DRSX4450/8GB
Category
Memory modules
Type
Datasheet

This manual is also suitable for

DRSX4450 INSTALLATION
INSTRUCTIONS
06705 B 1of 2
This manual describes how to install Dataram memory… …into these Sun Microsystems systems
Dataram Memory Upgrade
DRSX4450/2GB
DRSX4450/4GB
DRSX4450/8GB
DRSX4450LV/16GB
Sun Feature Code
X6380A
X6381A
X6382A
X6437A
Sun Fire X4150, X4250, X4450, Netra X4250 and X4450 Servers
System and Memory Configuration Overview
SYSTEM AND MEMORY OVERVIEW
The Sun Fire X4150 and Sun Fire X4250 have 16 DIMM slots for up to 64 GB (16 x 4GB) of PC2-5300 667 MHz ECC fully buffered DDR2 memory.
• 2 FB-DIMMs (minimum configuration) and 16 FB-DIMMs (fully populated configuration)
Caution: Refer to your system owner’s manual for detailed
instructions. System parts are sensitive to electrostatic
discharge and can be damaged by the static charge
you may carry. You should wear a grounded wrist strap.
• The DIMMs must be populated in pairs and the pairs must be identical in organization, size and speed.
• Install the highest-capacity DIMMs in the lowest-numbered DIMM slots.
The Sun Netra X4250 has 16 slots for up to 64 GB (16 x 4GB) of PC2-5300 667 MHz ECC fully buffered DDR2 memory.
• 2 FB-DIMMs (minimum configuration) and 16 FB-DIMMs (fully populated configuration)
• The DIMMs must be populated in pairs and the pairs must be identical in organization, size and speed.
• Install the highest-capacity DIMMs in the lowest-numbered DIMM slots.
Note: When 8GB DIMMs are available, this system will support 128 GB (16 x 8GB)
The Sun Netra X4450 has 32 slots for up to 128 GB (32 x 4GB) of PC2-5300 667 MHz ECC fully buffered DDR2 memory.
• 2 FB-DIMMs (minimum configuration) and 16 FB-DIMMs (fully populated configuration)
• The DIMMs must be populated in pairs and the pairs must be identical in organization, size and speed.
• Install the highest-capacity DIMMs in the lowest-numbered DIMM slots.
Note: When 8GB DIMMs are available, this system will support 256 GB (32 x 8GB)
The Sun Fire X4450 has 32 DIMM slots for up to 256 GB (32 x 8GB) of PC2-5300 667 MHz ECC fully buffered DDR2 memory.
• 2 FB-DIMMs (minimum configuration) and 32 FB-DIMMs (fully populated configuration)
• The DIMMs must be populated in pairs and the pairs must be identical in organization, size, voltage, and speed.
• Install the highest-capacity DIMMs in the lowest-numbered DIMM slots.
Note: Either 1.8V FB-DIMMs (X6382A, DRSX4450/8GB) or low voltage (LV) 1.5V FB-DIMMs (X6437A, DRSX4450LV/16GB) are supported. All FB-
DIMMs must be the same voltage. If you upgrade to LV 1.5V FB-DIMMs, you must replace all FB-DIMMs.
In all systems, the four memory channels are organized into two branches. Modules of identical size must be populated in pairs, starting with memory
slot 0 on each channel (slot 0 on each channel is marked with white handles). DIMMS should be installed with the largest module pair size first. For
example, (4) 4GB DIMMS and (4) 2GB DIMMS should be installed as follows: A0/B0=4G, C0/D0=4G, A1/B1=2G, C1/D1=2G.
(continued on next page)
DRSX4450 INSTALLATION
INSTRUCTIONS
06705 B 2of 2
(continued from previous page)
MEMORY INSTALLATION
Caution: If the top cover of the system is removed before the server
is powered off, the server will immediately go into Standby
mode.
Note: Refer to your system owner’s manual for detailed instructions.
Removing the Top Cover:
The top cover and fan door are integrated.
• Unlatch the fan module door.
• Pull the two release tabs back to release the door.
• Rotate the fan door to the open position and hold it there.
• Press the top cover release button and slide the top cover toward the rear of the server the rear about a half-inch.
• Lift up and remove the top cover.
• Unpackage the FB-DIMMs and place them on an antistatic mat.
• Ensure that the ejector tabs are in the open position.
• Line up the FB-DIMM with the connector.
• Align the FB-DIMM notch with the key in the connector. (This ensures that the FB-DIMM is oriented correctly).
• Push the FB-DIMM into the connector until the ejector tabs lock the FB-DIMM in place.
If the FB-DIMM does not easily seat into the connector, verify that the orientation of the FB-DIMM is as shown in the figure below. If the orientation is
reversed, damage to the FB-DIMM might occur.
Dataram Customer Support
In Europe:
Dataram's Technical Support Program goes beyond the lifetime
warranty, routine calls and questions. As memory specialists since 1967,
we want to provide the most comprehensive level of service and support
in the industry.
+45 70 212 217 (Phone)
+45 70 212 216 (FAX)
[email protected] (E-mail)
Our Customer Support representatives can answer your questions and
give you information on system/memory configurations, upgrade options,
product specifications, compatibility and other technical topics or issues.
In the U.S.A. and all other countries:
800-599-0071 (Toll Free)
609-799-0071 (Phone)
609-799-6734 (FAX)
[email protected] (E-mail)
If a Dataram memory board does not function properly we will issue a
Return Material Authorization number (RMA#) for the return of the
defective module(s) and express ship a repair or replacement to you at
no charge.
  • Page 1 1
  • Page 2 2

Dataram DRSX4450/8GB Datasheet

Dataram
Brand
Dataram
Model
DRSX4450/8GB
Category
Memory modules
Type
Datasheet
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents