Epson ELPIU03 User manual
- Category
- Projector mounts
- Type
- User manual
This manual is also suitable for
ELPIU03
Interactive Unit
Quick Setup Guide
Included Items
Interactive Unit
M4 x 10 mm hexagon socket head cap bolt
with washer and spring washer
(x1)
Epson Projector Software for
Easy Interactive Function CD
Easy Interactive Pen (x2)
AAA batteries (x4)
Pen tray
M4 hexagonal wrench
Document CD-ROM
Quick Setup Guide (this guide)
USB cable
Installing the Interactive Unit
Before attaching the Interactive Unit to the projector, install the ELPMB27 wall mount. See the
Installation
Manual
supplied with ELPMB27, and complete all steps up to step 8.
Warning:
Attachment to the projector should be performed by quali ed technicians using only approved mounting •
equipment.
Follow the steps below to attach this product. Incomplete or incorrect installation could cause the •
product to fall and cause personal injury or property damage.
M3 x 8 mm cross-head screw
(x1)
Insert the Interactive Unit into the ELPMB27 attachment plate.
a
Use the M4 x 10 mm bolt with washer and spring washer to secure the Interactive Unit.
b
Remove the USB cover, and then connect the USB cable.
c
Attach the USB cover, and then secure it using the M3 x 8 mm cross-head screw.
d
Adjust the length of the USB cable.
e
Next, go to step 9 in the ELPMB27
Installation Manual
and install the ELPMB27 arm cover, adjust the screen
position, then install the interface cover bracket and covers.
This product is an Interactive Unit for EB-435W/EB-430/EB-425W/EB-420/PowerLite 435W/PowerLite 430/
PowerLite 425W/PowerLite 420.
You can attach and use this product with a projector that has been mounted on a wall or hung from a ceiling.
This book explains how to mount the Interactive Unit when the projector is mounted on a wall using the wall
mount (ELPMB27). When hanging from a ceiling, see also the
Installation Guide
supplied with the attachment
plate (ELPPT04).
Prepare other tools as necessary.
ELPIU03
Interactive Unit
Quick Setup Guide
Included Items
Interactive Unit
M4 x 10 mm hexagon socket head cap bolt
with washer and spring washer
(x1)
Epson Projector Software for
Easy Interactive Function CD
Easy Interactive Pen (x2)
AAA batteries (x4)
Pen tray
M4 hexagonal wrench
Document CD-ROM
Quick Setup Guide (this guide)
USB cable
Installing the Interactive Unit
Before attaching the Interactive Unit to the projector, install the ELPMB27 wall mount. See the
Installation
Manual
supplied with ELPMB27, and complete all steps up to step 8.
Warning:
Attachment to the projector should be performed by quali ed technicians using only approved mounting •
equipment.
Follow the steps below to attach this product. Incomplete or incorrect installation could cause the •
product to fall and cause personal injury or property damage.
M3 x 8 mm cross-head screw
(x1)
Insert the Interactive Unit into the ELPMB27 attachment plate.
a
Use the M4 x 10 mm bolt with washer and spring washer to secure the Interactive Unit.
b
Remove the USB cover, and then connect the USB cable.
c
Attach the USB cover, and then secure it using the M3 x 8 mm cross-head screw.
d
Adjust the length of the USB cable.
e
Next, go to step 9 in the ELPMB27
Installation Manual
and install the ELPMB27 arm cover, adjust the screen
position, then install the interface cover bracket and covers.
This product is an Interactive Unit for EB-435W/EB-430/EB-425W/EB-420/PowerLite 435W/PowerLite 430/
PowerLite 425W/PowerLite 420.
You can attach and use this product with a projector that has been mounted on a wall or hung from a ceiling.
This book explains how to mount the Interactive Unit when the projector is mounted on a wall using the wall
mount (ELPMB27). When hanging from a ceiling, see also the
Installation Guide
supplied with the attachment
plate (ELPPT04).
Prepare other tools as necessary.
Getting Ready to Use the Interactive Unit
Install the Easy Interactive Driver ❏
Turn on the computer.
a
Insert the CD labeled "Epson Projector Software for Easy Interactive Function" in your computer.
b
Follow the on-screen instructions to install the software. When installation is complete, click
c
Finish
to close the installation screen.
Install the Easy Interactive Pen Batteries ❏
Remove the battery cover by pressing down on the tab, and then install the two batteries.
a
To reattach the battery cover, press the cover until you hear it click into place.
b
Connect to a Computer ❏
Connect the projector's VGA computer cable to the computer's monitor out port.
a
Connect the Interactive Unit's USB cable to the computer's
b
USB port.
Adjust the Position of the Projection Screen (Calibration) ❏
You need to perform calibration to match the position of the Easy Interactive Pen to the position of the
mouse cursor on the projection surface.
By performing calibration, the computer can accurately detect the position of the Easy Interactive Pen on the
projection surface.
Launch the Easy Interactive Driver.
a
For Windows
Select
Start
-
All Programs
(or
Programs
) -
Epson Projector
-
Easy Interactive Driver
.
For Mac OS X
Open the Applications folder, and then select
Easy Interactive Driver
.
For Windows
b
Click the pen icon on the taskbar, and then select
Calibrate (Normal)
or
Calibrate (Advanced)
.
For Mac OS X
Click the
pen icon in the Dock, select
Calibrate
from the menu bar, then select
Calibrate
(Normal)
or
Calibrate (Advanced)
.
Click
c
OK
when the start calibration message is displayed.
A ashing circle is displayed in the upper left corner of your projected image.
Tap the center of the circle with the tip of the pen.
d
The circle stops ashing. The next circle is displayed on the right.
Tap the center of the circle again, then repeat. When the circle reaches the right-hand side of the
e
image, the next circle is displayed on the next row.
Continue until all of the circles stop ashing.
f
Caution:
Because this product uses infrared communication, it could interfere with infrared communication from •
other product(s). If this does happen, move the other product(s) out of the detection area.
Do not stand between the Interactive Unit and the projected image while using the pen. If there are any •
obstacles between the Interactive Unit and the pen, it does not operate correctly.
Note:
Check •
http://www.epson.com
periodically as updates may be available for the Easy Interactive Driver.
You can use any interactive whiteboard software, or download •
Easy Interactive Tools
from the Epson
website at
http://www.epson.com
. Before using any software applications with the Interactive Unit, be
sure to read the software license agreement.
For more information, see the •
User's Guide
on the Document CD-ROM included with this product.
Copyright © Seiko Epson Corporation 2011. All rights reserved.
Printed in China.
Getting Ready to Use the Interactive Unit
Install the Easy Interactive Driver ❏
Turn on the computer.
a
Insert the CD labeled "Epson Projector Software for Easy Interactive Function" in your computer.
b
Follow the on-screen instructions to install the software. When installation is complete, click
c
Finish
to close the installation screen.
Install the Easy Interactive Pen Batteries ❏
Remove the battery cover by pressing down on the tab, and then install the two batteries.
a
To reattach the battery cover, press the cover until you hear it click into place.
b
Connect to a Computer ❏
Connect the projector's VGA computer cable to the computer's monitor out port.
a
Connect the Interactive Unit's USB cable to the computer's
b
USB port.
Adjust the Position of the Projection Screen (Calibration) ❏
You need to perform calibration to match the position of the Easy Interactive Pen to the position of the
mouse cursor on the projection surface.
By performing calibration, the computer can accurately detect the position of the Easy Interactive Pen on the
projection surface.
Launch the Easy Interactive Driver.
a
For Windows
Select
Start
-
All Programs
(or
Programs
) -
Epson Projector
-
Easy Interactive Driver
.
For Mac OS X
Open the Applications folder, and then select
Easy Interactive Driver
.
For Windows
b
Click the pen icon on the taskbar, and then select
Calibrate (Normal)
or
Calibrate (Advanced)
.
For Mac OS X
Click the
pen icon in the Dock, select
Calibrate
from the menu bar, then select
Calibrate
(Normal)
or
Calibrate (Advanced)
.
Click
c
OK
when the start calibration message is displayed.
A ashing circle is displayed in the upper left corner of your projected image.
Tap the center of the circle with the tip of the pen.
d
The circle stops ashing. The next circle is displayed on the right.
Tap the center of the circle again, then repeat. When the circle reaches the right-hand side of the
e
image, the next circle is displayed on the next row.
Continue until all of the circles stop ashing.
f
Caution:
Because this product uses infrared communication, it could interfere with infrared communication from •
other product(s). If this does happen, move the other product(s) out of the detection area.
Do not stand between the Interactive Unit and the projected image while using the pen. If there are any •
obstacles between the Interactive Unit and the pen, it does not operate correctly.
Note:
Check •
http://www.epson.com
periodically as updates may be available for the Easy Interactive Driver.
You can use any interactive whiteboard software, or download •
Easy Interactive Tools
from the Epson
website at
http://www.epson.com
. Before using any software applications with the Interactive Unit, be
sure to read the software license agreement.
For more information, see the •
User's Guide
on the Document CD-ROM included with this product.
Copyright © Seiko Epson Corporation 2011. All rights reserved.
Printed in China.
-
1
-
2
-
3
-
4
Epson ELPIU03 User manual
- Category
- Projector mounts
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI