Barco AP24-3D is a high-performance audio processor designed for immersive audio experiences in cinema, post-production, and live event applications. With its advanced 3D audio capabilities, it allows users to create and deliver captivating soundscapes that transport audiences to the heart of the action. The AP24-3D supports up to 64 audio channels and features a wide range of audio processing tools, including EQ, dynamics, delay, and reverb. It also offers immersive audio formats such as Dolby Atmos, DTS:X, and Auro-3D, enabling users to create truly immersive and engaging audio experiences.
Barco AP24-3D is a high-performance audio processor designed for immersive audio experiences in cinema, post-production, and live event applications. With its advanced 3D audio capabilities, it allows users to create and deliver captivating soundscapes that transport audiences to the heart of the action. The AP24-3D supports up to 64 audio channels and features a wide range of audio processing tools, including EQ, dynamics, delay, and reverb. It also offers immersive audio formats such as Dolby Atmos, DTS:X, and Auro-3D, enabling users to create truly immersive and engaging audio experiences.
AP20 & AP24 F an Re placement Kit
Installation Manual
R59770891/00
28/09/2015
Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: +32 56.36.82.11
Fax: +32 56.36.883.86
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in Belgium
Changes
Barco p rovides this manual ’as is’ w ithout warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or m erchantability and fitness for a particular purpose. Barco may m ake improvements and/o r cha nges to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication c ould contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can b e downloaded from the Barco web site w
ww.bar co.com or from the secured Barco web site
h
ttps://www.barco.com/en/signin.
Copyright ©
All rights reserved. No part of this document may be copied, re produced or translated. It s hall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Trademarks
Brand and product names m entioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names me ntioned in this man ual serve as com men ts or examples and are not to be understood as advertising for
the products or their m anufacturers.
1. Fan replacement kit
1. FAN REPLACEMENT KIT
Overview
• Kit c onte nt
• Installation process overview
• Remove the top cover
• Remove the front panel assembly
• Remove the po wer supply assembly
• Replace the fan as sem bly
• install the power supply assembly
• Install the front panel assem bly
• Install the top co ver
WARNING: This manual is only intended for qualified service personnel.
1.1 Kit content
What’s in the box?
This kit contains the following:
• 1 fan subassembly
• 4 Keps nuts, 6–32, steel, clear zinc finish
• 4 screws, 6–32 x 1/2” flat-head Ph illips, 100 degree, steel, clear z inc
Purpose of the s pare part kit
The fan subassembly in the fan replacement k it is designed to replace the fan o f the A P20 and AP24 audio processor. This doc ument
describes in detail the replacem ent procedures.
1.2 Installation process overview
About this chapter
This chapter gives an overview of the different stages in the installation process. The stages displayed in bold are described in more
detail in this m anual. M ore information abo ut the other stages can be found in the service man ual of the aud io pr ocessor.
Safety warnings
WARNING: Servicingmustbedonebyauthorizedandqualified technical personnel only, which are thor-
oughly familiar with the product and all of the proper safety checks of this product.
CAUTION: T he AP 20 and AP24 audio processors co ntain parts that are static sensitive. Use caution when
handling to avoid damage and avoid touching circuit boards.
When remo ving or installing internal cables, keeping one hand on the chassis will help to ground you with
respect to internal circuitry.
It is a good idea to stand on a linoleum or cement floor (not carp et) w hen handling the processo r.
Installation from A to Z
1. Find a suitable workspace to pe rform the procedure. Antistatic foam or an antistatic m at is an ideal work surface.
2. Turn off the processor’s rear panel power switch and unplug the power cord.
3. R emov e the top cover. See "Remove the top cover", page 2
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
1
1. Fan replacement kit
4. R emov e the front panel assembly. See "Remove the front panel assembly", page 2
5. R emov e the power supply assembly. See "Remove the power supply assembly", page 4
6. R eplace the fan assembly. See "Replace the fan assembly", page 4
7. Install the power supply assembly. See "install the power s upply assembly ", page 6
8. Install the front panel assembly. See "Install the front panel assembly", page 6
9. Install the top cover. S ee "Install the top cover", page 7
10.C onnect the audio processor to the AC power and turn it on.
11.Verify if the new fan is w orking correctly.
1.3 Remove the top cover
Necessary tools
#2 Phillips screwdriver
How to remove the top cover from the audio processor?
1. R emov e the two 4–40 x 1/4” pan head Phillips screws from both sides of the top cover.
Image 1-1
2. S lide the top cover to the back of the processor.
Image 1-2
3. L ift the top cover up to remove it.
1.4 Remove the front panel assembly
Necessary tools
#1 Phillips screwdriver
How to remove the front panel a ssemb
ly?
1. C arefully turn the processor on its side.
2. R emov e four 4–40 x 3/16” flat-head Phillips screws from the bottom.
2
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
1. Fan replacement kit
Image 1-3
3. P lace the processor back down with the top facing upwards.
4. G ently rem ove the ribbon cable connector from the front p anel.
Image 1-4
Tip: Pull evenly on both sides and be ca reful not to bend pins or damage the ribbon cable connector.
Do not tug on the wire s to remove the connector, as this m a damage the c able.
5. R emov e four 4–40 x 3/16” fla t-head Phillips sc rews on both sides of the processor (eight in total).
Image 1-5
Note: Be careful when removing the last screws.
6. Fold the front panel dow n
and away, to provide more room to access to the fan.
Note: be careful not to stress any of the cables that are still attached.
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
3
1. Fan replacement kit
1.5 Remove the power supply assembly
Necessary tools
#1 Phillips screwdriver
How to remove the power supply assembly?
1. R emov e t hree of the four 6–32 x 1/4” pan-head P hillips screws that hold the power supply in place; These screws can be found
on the side.
Image 1-6
2. R emov e the fourth screw, while holding the p ower supply. Do this so that the power supply will not fall.
3. C arefully lift the power supply ou t and set it on top of the car d cage.
Tip: No cables need to be removed from the power supply, but make sure not to stress the cables.
Image 1-7
1.6 Replace the fan assembly
Necessary tools
• A s mall flat-blade screwdriver
• #2 Phillips screwdriver
• 5/16” combination wrench
Necessary parts
• Sub-Assembly, Fa n
• Keps nuts, 6–32, s teel, clear zinc finish (4 pieces)
• Screw, 6–32 x 1/2” flat head Phillips, 100°, steel, clear z inc (4 pieces)
How to replace the fan assembly?
1. R emov e the fan power connector from the front panel.
Tip: Useasmallflat-b lad e screw d river to h
elp lift up the connector out of the socket.
Caution: Do not pull the power connector directly up on the wires. This will pull them out of the connector.
4
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
1. Fan replacement kit
Image 1-8
2. R emov e four 6–32 x 1/2” flat-head Phillips screws and four 6–32 Keps nuts holding the fan to the chassis.
Image 1-9
3. R emov e the fan assem bly.
4. Install the new fan assembly, using four 6–32 x 1/2” flat-head Phillips sc rews and four 6–32 Keps nuts.
Note: New screws and nuts for this are included in the kit, as e xisting hardware may be covered in old Loc tite.
Make sure that the w ires and arrows indicating air flow direction are in the correct orientation.
Image 1-10
5. C onnect the fan power cable to t
he front panel board socket CN1. The connector is keyed to go into th e socket in only one
direction.
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
5
1. Fan replacement kit
Image 1-11
1.7 install the power supply assembly
Necessary tools
#1 Phillips screwdriver
Necessary parts
Four 6 –32 x 1/4” pan- head Phillips screws
How to install the power supply assembly?
1. M ove the power supply bac k into place, taking care of the cabling.
2. Install the pow er supply, using four 6–32 x 1/4” pan-head Phillips screws.
Image 1-12
1.8 Install the front panel assembly
Necessary tools
#1 Phillips screwdriver
Necessary parts
eight 4–40 x 3/16” flat-head Phillips screws
How to install the front panel assembly?
1. S lide the front panel bac k into the chassis.
2. Insert four 4–40 x 3/16” flat-head P hillips screws on each s ide to se cure.
6
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
1. Fan replacement kit
Image 1-13
3. Insert the ribbon cable back into the socket.
Image 1-14
Note: be care ful not to bend pins.
4. C arefully turn the processor on its side.
5. Install four 4–40 x 3/16” flat-head Phillips screws in bottom p late.
Image 1-15
6. P lace the processor back dow n.
7. Inspe ct the processor to make sure t hat a ll c onnectors are properly seated and the screws and nuts are tight.
1.9 Install the top cove r
Necessary tools
#1 Phillips screwdriver
R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
7
1. Fan replacement kit
Necessary parts
Tw o 4–40 x 1/4” pan-head Ph illips sc rews
How to install the top cover?
1. P lace the top cover correctly on the top o f the processor.
Note: There is a lip that slides under the front panel assembly in front and a back lip that slides over the top lip of the rear panel
assemb ly.
Image 1-16
Image 1-17
2. O nc e the top cover is properly seated, install two 4–40 x 1/4” pan -head Ph illips screws.
Note: If the screw holes are not lined up correctly, the cover is not seated correctly. Adjust the top cover if ne cessary.
Image 1-18
8 R59770891 AP20 & AP24 FAN REPLACEMENT KIT 28/09/2015
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Barco AP24-3D Installation guide
- Type
- Installation guide
- This manual is also suitable for
Barco AP24-3D is a high-performance audio processor designed for immersive audio experiences in cinema, post-production, and live event applications. With its advanced 3D audio capabilities, it allows users to create and deliver captivating soundscapes that transport audiences to the heart of the action. The AP24-3D supports up to 64 audio channels and features a wide range of audio processing tools, including EQ, dynamics, delay, and reverb. It also offers immersive audio formats such as Dolby Atmos, DTS:X, and Auro-3D, enabling users to create truly immersive and engaging audio experiences.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco E2-Tri-Combo User guide
-
Barco EC-200 User guide
-
Barco RS905948/00 User manual
-
-
-
-
-
Barco Galaxy NW-12 EX Installation guide
-
Barco UDM-W22 Installation guide
-
Barco SFP input card Installation guide
Other documents
-
Seasonal Designs RF8P User manual
-
Datasat AP20 Installation guide
-
Fujitsu LQFP-64P User manual
-
Simrad AC42 Installation guide
-
-
-
-
-
American Panel Freezer AP24BC250-3 User manual
-
Xilinx Virtex-II Pro ML321 User manual
