AmazonBasics B07Y2CND3Q User manual

Window-Mounted Air Conditioner with Remote, Energystar

Sistema de Aire Acondicionado para Instalación en Ventanas, con

Control Remoto, Energystar

Climatiseur De Type Fenêtre avec Télécommande, Certiﬁé Energystar

B07Y2CND3Q, B07Y2C57KD, B07Y2B3ZXV, B07N6LPL7V

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Españo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

3

x 2

Ø 1/8"

LEFT

RIGHT

A (x 1) B (x 1) C (x 1)

D (x 1) E (x 1) F (x 1)

G (x 2) H (x 2) I (x 1)

J (x 1) K (x 4) L (x 7)

M (x 2) N (x 2)

AAA

3.2 mm

4

EN

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use.

If this product is passed to a third party, then these instructions

must be included.

When using electrical appliances, basic safety precautions should always

be followed to reduce the risk of ﬁre, electric shock, and/or injury to

persons including the following:

DANGER

Risk of ﬁre or explosion! Flammable refrigerant used.

To be repaired only by trained service personnel. Do not

puncture refrigerant tubing.

WARNING

Risk of ﬁre. Flammable

materials. This product uses refrigerant

R32 and must be disposed of by a licensed

refrigeration mechanic with knowledge of

appropriate gas reclamation methods.

WARNING

Do not pierce or burn. Be aware that refrigerants may

not contain an odor. Appliance shall be installed, operated and stored in

a room with a ﬂoor area larger than 120 ft

2

(11 m

2

).

• This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

• Children should be supervised to ensure that they do not play with

the product.

• Do not block air inlets and/or air outlets.

• Do not operate with wet hands.

• Do not disassemble or modify the product.

• Always switch off the product before pulling the power plug out of the

wall outlet.

• This product shall be installed in accordance with national wiring

regulations.

• If there is a gas leak from another product, ventilate the room before

operating the product.

5

EN

• Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock, ﬁre or damage

the product.

• Disconnect the plug from the wall outlet when not using the product

for a long time.

Battery Warnings

• Always insert batteries correctly with regard to polarity (+ and –)

marked on the battery and the product.

• Exhausted batteries should be immediately removed from product

and properly disposed of.

Grounding Instructions

• This product must be grounded while in use to protect the operator

from electrical shock. The product is equipped with a 3-conductor

cord and a 3-prong grounding-type plug. This product can only be

used with a standard 3-prong wall outlet to minimize the possibility

of electric shock. Where a 2-prong outlet is encountered, it must be

replaced with a properly grounded 3-prong wall outlet.

• Always use dedicated power circuit with a dedicated circuit breaker.

• Before connecting the product to the power supply, check that the

power supply voltage and current rating corresponds with the power

supply details shown on the product rating label.

• If the power cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualiﬁed persons in order

to avoid a hazard.

• Do not modify power cord length or share an outlet with another

appliance. This may cause electric shock or ﬁre.

• Do not use the outlet if it is loose or damaged. It may cause electric

shock.

• Always plug this product directly into a wall outlet/receptacle. Never

use with an extension cord or relocatable power tap (outlet/power

strip).

6

EN

Grounding pin

SAVE THESE INSTRUCTIONS

Intended Use

• This product is intended to regulate temperature and humidity

indoors.

• This product is intended for a ﬁxed installation in a window only. The

power cord must be connected to indoor power supply only. This

product is not intended for use in bathrooms, laundry areas and

similar indoor locations.

• This product is intended for household use only. It is not intended for

commercial use.

• This product is intended to be used in dry indoor areas only.

• No liability will be accepted for damages resulting from improper use

or non-compliance with these instructions.

7

EN

Before First Use

• Check the product for transport damages.

• Remove all the packing materials.

• Before connecting the product to the power supply, check that the

power supply voltage and current rating corresponds with the power

supply details shown on the product rating label.

DANGER

Risk of suffocation! Keep any packaging materials away

from children – these materials are a potential source of danger, e.g.

suffocation.

Product Description

Main unit

RESET

TEST

O

P

Q

R

Y

V

U

T

S

W

O

Power plug with indicator

P

RESET button

Q

TEST button

R

Control panel

S

Bottom rail

T

Shutter locks

U

Front grill

V

Air vent control lever

(for B07Y2C57KD and

B07Y2B3ZXV only)

W

Air vents

Y

Fresh air vent control

8

EN

Controls

Control panel

Remote control

1

2

3

4

5

6

7

8

9

16

15

13

12

10

X

17

3

4

9

10

7

8

20

14

2

22

21

23

24

15

12

16

13

25

26

27

6

11

14

18

19

1

Main unit display

15

Timer button

2

Decrease button

16

Increase button

3

Timer on indicator

17

Relay signal indicator

4

Timer off indicator

18

Sleep indicator

5

Clean ﬁlter button

19

Reset button

6

Mode indicator

20

Follow me button

7

Mode button

21

Lock button

8

Energy Saver button

22

LED button

9

Follow me indicator

23

Clock button

10

On/off button

24

Cancel button

11

Remote control receiver

25

Child lock indicator

12

Fan button

26

Temperature indicator

13

Fan speed indicator

27

Power on indicator

14

Sleep button

X

Display

9

EN

Window Requirements

Wooden window

A

B

offset

inner window sill

Vinyl-clad window

A

B

offset

inner

window sill

Installation

• The product should be installed by 2 skilled persons.

• To avoid vibration and noise, make sure the product is installed

securely and ﬁrmly.

• The window should be able to withstand the weight of the product.

• Install the product where the sunlight does not directly shine on it. If

the product receives direct sunlight, build an awning to shade it.

10

EN

• The rear part of the product must be installed outdoors, not inside a

building, garage or another room.

• There should be no obstacles, such as a fence or wall, within 20"

(50cm) from the back of the product and the side louvers. Obstacles

might limit the heat radiation, which greatly reduces the cooling

efﬁciency of the product.

• Install the product with its bottom portion approx. 30-60"

(75-150cm) above the ﬂoor level.

• Install the product within a reach to the wall outlet.

CAUTION

Risk of cuts! When handling the product be careful to

avoid cuts from sharp metal edges.

Step 1

K

F

• Attach the top rail (F) with 4 screws (K) by following the pre-drilled

holes on the unit.

11

EN

Step 2

x2

R

E

2

1

NOTICE

The accordion shutters are marked LEFT (D) and RIGHT (E)

for easy identiﬁcation.

• Slide the rail of the right accordion shutter (E) out of the frame.

• Slide the rail into the shutter locks (T) of the main unit.

• Repeat on the other side with the left accordion shutter (D).

Step 3

x2

E

F

Q

• Slide the top and bottom rails of the right accordion shutter (E) into

the top rail’s (F) channel and the bottom rail (S).

• Repeat on the other side with the left accordion shutter (D).

12

EN

Step 4

Wooden window Vinyl-clad window

Q

A

• Place the product on the window sill. The bottom rail (S) needs to be

placed against the window sill’s offset.

NOTICE

Ensure the product is tilted 3° to 4° (A = 0.75 - 1" /

1.9-2. cm) downwards with reference to the window sill.

Step 5

E

D

• Fully extend the accordion shutters (E) and (D) so they ﬁt the window

frame.

• Not shown: Use the strips of the weather stripping (C) to close any

leaking points. Cut them to the required size and remove the wax

paper. To improve insulation, stick them on appropriate areas.

13

EN

Wooden window

Vinyl-clad window

E

G

L

H

L

E

NOTICE

Ensure the product is tilted 3° to 4° (A = 0.75 - 1” /

1.9-2. cm) downwards with reference to the window sill.

• Wooden windows: Secure the accordion shutters (E) and (D) with the

brackets (G) and the screws (L).

• Vinyl clad windows: Secure the accordion shutters (E) and (D) with

the brackets (H) and the screws (L).

Step 7

D

E

L

F

1 1

2

NOTICE

Before securing the accordion shutters (E) and (D) and

the top rail (F), mark and drill 3 pilot holes in the lower window sash to

prevent it from splitting.

• Close the window sash, so it rests on the top rail (F) and the

accordion shutters (E) and (D).

• Attach the accordion shutters (E) and (D) and the top rail (F) guided

by the pre-drilled holes to the window sash using 3 screws (L).

14

EN

Step 8

L

I

NOTICE

Before securing the lower window sash, mark and drill 2

pilot holes to prevent it from splitting.

• Secure the position of the lower window sash using the bracket (I)

and 2 screws (L).

Step 9

1

2

B

• Measure the width of the window sash.

• Cut the sash seal (B) so it ﬁts the space between the lower and upper

window sash.

15

EN

Step 10

B

• Place the sash seal (B) between the lower and upper window sash.

Step 11

x2

2

1

x

• Measure the widths between the isolation board intakes of the

accordion shutters (E) and (D).

• Cut the isolation boards (N) according to the measured widths.

16

EN

Step 12

x2

N

• Slide the isolation boards (N) into the ledge of the accordion shutters

(E) and (D).

Operation

Performance test

DANGER

Risk of electric shock! The power plug of this product

provides LCDI protection (Leakage Current Detection and Interruption).

If the LCDI is de-activated this indicates an arcing fault. Unplug and

check the power cord and product. If no damage is visible, reset the

product by pressing the RESET button (N). If the LCDI de-activates

again, a hazardous condition may be present and the product should

be discarded or returned to an authorized service facility for examination

and/or repair.

CAUTION

Risk of electric shock! Run performance test before

each use.

• Press the RESET button (N).

• Connect the power plug to a wall outlet. The power plug indicator (M)

lights up.

• Press the TEST button (Q). The RESET button (P) should pop out

and the indicator on the power plug (O) should go off.

17

EN

• Press the RESET button (P) again. The indicator on the power

plug (O) lights up again and the product is ready for use.

NOTICE

If the indicator on the power plug (O) does not light up,

consult a specialist before using the product.

Installing/replacing the batteries

NOTICE

The batteries are not provided. Use 2 x 1.5 V type

AAA/LR03 batteries.

Switching on/off

To switch on/off the product, press the on/off button (10) either on

the remote control or on the control panel.

Mode control

To set the mode, press the mode button (7). The active mode is indicated

by the mode indicator (6).

Icon

control panel

Icon

remote control

Description

Auto: Depending on the set

target temperature and the

room temperature, the product

automatically switches between

cooling mode and fan mode. The

fan speed cannot be regulated

manually.

Cool: Airﬂow with cooling.

Dry: In this mode the product

mainly has a dehumidifying function.

There will be a little unavoidable

cooling effect on the room too.

The fan speed cannot be regulated

manually.

Fan: Airﬂow only.

Fan control

To set the fan mode, press the fan button (12). The fan speed is

indicated by the fan speed indicator (13).

18

EN

Icon

control panel

Icon

remote control

Description

Auto: Depending on the selected

mode, the set temperature and

the room temperature, the product

automatically sets the fan speed.

Low airﬂow

Medium airﬂow

High airﬂow

Temperature control

NOTICE

The temperature control does not work in fan mode.

Set the target temperature with the decrease (2) and increase (16)

buttons. The set temperature is shown on the display of the control panel

and the remote control.

Timer control

You can set the timer (0.5 to 24 hours) after which period the product

automatically switches on or off.

Set timer

• Press the timer button (15) to initialize the timer setting.

• Press the timer button (15) several times to toggle between the

on timer and the off timer. The chosen function is indicated by the

timer indicators (3 and/or 4).

• Set the timer with the decrease (2) and increase (16) buttons.

The set time is shown on the display of the control panel and the

remote control.

• Wait 5 seconds. The timer is now set and starts to run. The timer

indicator (3 and/or 4) light up if a timer is running.

NOTICE

The temperature control does not work in fan mode.

Cancel timer

• To reset the timers, press the cancel button (24) or press and hold

the timer button (15) for 3 seconds.

– This deletes the timer setting.

– If the ON timer is being canceled, the product switches off.

– If the OFF timer is being canceled, the product switches on.

19

EN

– Alternatively, you can set the concerned timer to 0.0 h.

Sleep function

NOTICE

The sleep function works only when the product is set to

cooling or auto mode.

– The sleep function increases the target temperature by 2 °F (1 °C) 30

minutes after activation.

– After another 30 minutes the target temperature is increased by

another 2 °F (1 °C).

– The product maintains the temperature for the following 6

hours. Afterwards, the product returns to the originally selected

temperature.

• Press the sleep button (14) to activate the sleep function. The

activated sleep function is being indicated with a light above the

sleep button (14) and with a on the remote control display (X).

Energy saver

NOTICE

The energy saver control does not work in fan mode.

– While the energy saver is activated, the product is cooling the room

with the maximum compressor efﬁciency below the set target

temperature.

– When the room temperature is below the set temperature, the

compressor switches off. Only the fan is working in short intervals.

– When the room temperature increases above the set target

temperature, the compressor switches on again.

• Press the energy saver button (8) to activate the energy saver.

The activated energy saver is being indicated with a light above the

energy saver button (8).

Follow me function

• Press the follow me button (20) to activate this function.

• While activated:

– The follow me indicator (9) lights up and is shown on the left

side of the remote control display (X).

– The remote control displays the temperature of its immediate

surroundings.

20

EN

– While activated, the product uses the temperature sensor of the

remote control to measure the room temperature.

– The remote control transmits the measured temperature in 3-minute

intervals to the main unit.

– This allows to set the target temperature for a speciﬁc location in the

room.

NOTICE

When the main unit does not receive any signal from the

remote control for 7 minutes, it switches off the follow me function.

As soon as the temperature signal is being received, the main unit

automatically switches on the follow me function.

Clock

The remote control is equipped with a clock. The time is shown on the

left side of the display (X).

• Press the clock button (23) for 3 seconds. The clock starts to

ﬂash.

• Set the time with the decrease (2) and increase (16) buttons. Press

and hold the button to change the time quicker.

• Press the clock button (23) to conﬁrm the setting.

°F/°C

Press and hold both the decrease (2) and the increase (16) button

for 3 seconds to toggle the temperature units between Fahrenheit and

Celsius.

NOTICE

When the main unit does not receive any signal from the

remote control for 7 minutes, it switches off the follow me function.

As soon as the temperature signal is being received, the main unit

automatically switches on the follow me function.

Child lock

NOTICE

The child lock is only available for the remote control. The

control panel (P) is always active.

• To activate/deactivate the child lock, press the lock button (21),

e.g. with a toothpick.

• When the child lock is activated:

– is shown on the right side of the remote control display (X).

– All buttons of the remote control are locked.

Page is loading ...

AmazonBasics B07Y2CND3Q User manual

This manual is also suitable for

AmazonBasics B07Y2CND3Q User manual

Related papers

Other documents