BELGACOM twist 300 User manual

Brand: BELGACOM

Model: twist 300

Category: Telephones

Type: User manual

Belgacom Twist

300

User manual

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / Overview.fm / 12.08.2009

Twist 300

11.12. 11:56

INT MENU

1 Charge status of

the batteries

2Display keys

3Message key

Flashes: new messages

received

4 Handsfree key

5 Control key (u)

6Talk key

7Directory key

(press down)

8 End call and

On/Off key

9Ringer on/off

(press and hold

in idle status)

10 Keypad lock on/off

(press and hold)

11 Recall key

- Consultation call

(flash)

- Dialling pause

(press and hold)

12 Microphone

13 "Microphone off" key

The base station at a glance

Twist 300 base station

The handset at a glance

Display keys on handset:

Pressing a key launches the function that

appears above that key in the display.

Display

icon

Function when pressed

INT

Call other registered hand-

sets

¢ page 9.

Open main/submenu (see

Menu tree

¢ page 12).

“

Go back one menu level.

Scroll up/down or adjust vol-

ume with u.

Move cursor to left/right with

Backspace deletes one char-

acter at a time from right to

left.

Confirm menu function or

save entry.

Registration/paging key:

Search for handsets (press briefly, "Paging"

¢ page 9)

¢ page 9).

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / Overview.fm / 12.08.2009

Safety precautions

Emergency numbers cannot be dialled if the keypad lock

(¢ page 1) is activated!

Care

Wipe down the base station and handset with a

damp cloth (no solvents) or an antistatic cloth.

Never use a dry cloth. This can cause static.

Contact with liquid

If the handset should come into contact with

liquid:

◆ Switch the handset off and remove the bat-

teries immediately.

◆ Allow the liquid to drain from the handset.

◆ Pat all parts dry, then place the handset with

the battery compartment open and the keypad

facing down in a dry, warm place for at least

hours (not in a microwave, oven etc.).

◆ Do not switch on the handset again until it is

completely dry.

When it has fully dried out, you will normally be

able to use it again.

Read this user guide and the safety precautions carefully

before use. Explain their content and the potential haz

ards associated with using the telephone to your chil-

dren.

Only use the mains adapter supplied.

Fit only the recommended, rechargeable

batteries (¢ page 11), i.e. never use any

other battery type or non-rechargeable batter-

ies as this could result in significant health risks

and personal injury.

The operation of medical appliances may be

affected. Be aware of the technical conditions

your particular environment, e.g. doctor's

surgery.

Do not hold the rear of the handset to your ear

when it is ringing. Otherwise you risk serious

and permanent damage to your hearing.

The handset may cause an unpleasant hum-

ming noise in hearing aids.

Do not install the phone in a bathroom or

shower room. The handset and base station

are

not splashproof.

Do not use your phone in environments with a

potential explosion hazard, e.g. paint shops.

If you give your phone to someone else, make

sure you also give them the user guide.

Please remove faulty base stations from use or

have them repaired by our service, as they could

interfere with other wireless services.

Disposal

Batteries should not be disposed of in general

household waste. Observe the local waste dis

posal regulations, details of which can be

obtained from your local authority or the dealer

you purchased the product from.

All electrical and electronic equipment must be

disposed of separately from general household

waste using the sites designated by local

authorities.

If a product displays this symbol of a crossed-out

rubbish bin, the product is subject to European

Directive 2002/96/EC.

The appropriate disposal and separate collec-

tion of used equipment serve to prevent poten-

tial harm to the environment and to health.

They are a precondition for the re-use and recy

cling of used electrical and electronic equip-

ment.

For further information on disposing of your

used equipment, please contact your local

authority, your refuse collection service or the

dealer you purchased the product from.

Not all of the functions described in this user guide are

available in all countries.

ECO DECT

You are helping to protect the environment with

your Twist 300.

Reduced energy consumption

Your telephone has a power-saving adapter plug

and uses less power.

Reduced transmission power

The transmission power of your telephone is

reduced automatically:

The handset's transmission power is reduced

depending on the distance to the base station.

The transmission power on the base station is

reduced to virtually zero when only one handset

is registered and the handset is in the base sta

tion.

You can reduce the transmission power of the

handset and base station even more by using

Eco Mode/Eco Mode+ (see Menu tree

¢ page 13):

◆ Eco Mode: 80% transmission power reduc-

tion in standby mode and during a call (the

range of the base station is reduced).

◆ Eco Mode+: 100% transmission power deac-

tivation in standby mode (top left display icon

½). Press and hold the talk key c to check

that the base station can be reached. You will

hear the ringing tone if the base station can

be reached.

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / starting.fm / 12.08.2009

First steps

Check the pack contents

◆ one Twist 300 base station,

◆ one mains adapter,

◆ one handset,

◆ one phone cord,

◆ two batteries,

◆ one battery cover,

◆ one user guide.

If you have purchased a model with multiple handsets, the package should contain two

batteries, a battery cover and a charging cradle with mains adapter for each additional

handset.

Setting up the base station and charging cradle (if included)

The base station and charging cradle are is designed for use in enclosed dry rooms with a

temperature range of +5°C to +45°C.

¤ Set up the base station at a central location on a flat, non-slip surface in your house or

apartment.

The phone's feet do not usually leave any marks on surfaces. However, due to the multi-

tude of different varnishes and polishes used on today's furnishings, the occurrence of

marks on the surfaces cannot be completely ruled out.

You can also mount the base station and charging cradle on the wall.

Please note:

◆ Never expose the telephone to the influence of heat sources, direct sunlight or other

electrical devices.

◆ Protect your telephone from moisture, dust, corrosive liquids and vapours.

Connecting the base station

¤ First connect the mains adapter 1.

¤ Then connect the telephone jack 2

and insert the cables into the cable

ducts.

Please note:

◆ The mains adapter must always be

connected, as the phone will not

operate without mains connection.

◆ Only use the mains adapter and

phone

cord supplied.

Please note

Pay attention to the range of the base station.

This is up to 300 m in unobstructed outdoor areas and up to 50 m inside buildings.

The range is reduced when Eco Mode (

¢ page 13) is activated.

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / starting.fm / 12.08.2009

Connecting the charging cradle (if included)

Setting up the handset for use

The display is protected by a plastic film.

Please remove the protective film!

Inserting the batteries and closing the battery cover

¤ Connect the flat plug from the power supply 1.

¤ Plug the mains adapter into the plug socket 2.

If you need to disconnect the plug from the charging cradle,

press the release button 1 and disconnect the plug 2.

Warning

Use only the rechargeable batteries (¢ page 11). Never use conventional (non-

rechargeable) batteries, as this could result in significant health risks and damage to

property. For example, the outer casing of the batteries could be destroyed or the

batteries could explode. The phone could also malfunction or be damaged as a result

of using batteries that are not of the recommended type.

¤ Insert the batteries the right

way round.

The polarity is indicated in/on

the battery compartment.

¤ Slide the battery cover back into the

main casing until it clicks into place.

If you need to open the battery cover,

or instance to replace the batteries,

place your fingertip in the grooved area

on the top of the cover and slide down.

–

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / starting.fm / 12.08.2009

Placing the handset in the base station and registering

If you have purchased a model with multiple handsets, repeat the registration process

for each individual handset. Handsets are assigned the lowest available internal number

(1–4). If more than one handset is registered to the base station, the internal handset

number appears in the top left of the display, e.g. 2. If the internal numbers 1–4 are

already assigned to other devices, number

4 will be overwritten.

Initial charging and discharging of the batteries

The correct charge level can only be displayed if the batteries are first fully charged and

discharged.

Please note

◆ Each key press interrupts the automatic registration.

◆ If automatic registration does not work, the handset will have to be registered

manually

(¢ page 9).

◆ Only place the handset in the base station or charging cradle that is intended for

it.

Registering

INT MENU

Before you can use the phone, you must first register the

handset to the base station.

The handset registers automatically.

Registration can take up to 5 minutes.

Do not remove the handset from

the base station during this time.

After successful registration, the idle screen is displayed.

Charge status of the batteries:

–

= e V U (flat to full)

–

= flashes: batteries almost flat

–

e V U flashes: charging

Put into base

¤ Place the handset with

the display facing up

in the base station.

¤ Place the handset in the base station or charging cradle for

eight hours.

¤ Then remove the handset from the base station or charging cradle

and do not replace it until the batteries are fully discharged.

8 h

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / starting.fm / 12.08.2009

Setting the language

To make it easier for you to use your phone, we suggest changing the language (default

language: English):

◆ MENU ¢ Settings with u and press OK

◆ ¢ Handset with u and press OK

◆ Language is displayed, press OK

◆ Select the correct language with u and press OK.

◆ ¢ a (press and hold to return to idle status

See "Changing the display language" ¢ page 10, for instructions on changing the lan-

guage.

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming calls,

and so that the alarm can be used.

MENU ¢ Settings ¢ OK ¢ Date/Time ¢ OK

¢ Date: ¢ ~ (enter the day, month and year in 6-digit format) ¢ OK

¢ Time: ¢ ~ (enter hours and minutes in 4-digit format) ¢ OK (display message: Saved)

¢ a (press and hold to return to idle status)

Display in idle status

Once the phone is registered and the time set,

the idle display is shown as in this example.

Activating/deactivating the handset

Press and hold the end call key a to activate or deacti-

vate the handset.

If you place a deactivated handset in the base station or

charging cradle, it will automatically activate.

Your phone is now ready for use!

If you have any questions about using your phone, please read the tips on troubleshooting

Questions and answers" ¢ page 11).

Please note

◆ After the first battery charge and discharge you may replace your handset in the

base station or charging cradle after every call.

◆ Always repeat the charging and discharging procedure if you remove the batteries

from the handset and reinsert them.

◆ The batteries may warm up during charging. This is not dangerous.

◆ After a while, the charge capacity of the batteries will decrease for technical rea-

sons.

Please note

When entering the time and date, you can move the position of an entry to the left

or right by pressing the control button up or down.

11.12. 11:56

INT MENU

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

Making calls

Making external calls and ending calls

External calls are calls using the public telephone

network.

(Enter the phone number) ¢c.

The phone number is dialled. (Or you can first

press and hold

c [dial tone] and then enter the

number.) During the call you can adjust the ear

piece volume using t and set the volume with u.

End the call/cancel dialling:

Press the end call key a.

Accepting a call

The handset indicates an incoming call by ringing

and by a display on the screen.

Press the talk key c to accept the call.

When Auto Answer is activated (see Menu tree

¢ page 13), simply remove the handset from the

base station/charging cradle.

In idle status, use t to activate the menu for set-

ting the call volume and use u to set the volume.

Calling Line Identification

When you receive a call, the caller's number will be

displayed on your handset; the caller's name will

be displayed if it is stored in the directory or if CNIP

has been requested.

Requirements:

1 You have asked your network provider for the

caller's number (

CLIP) or name (CNIP) to be dis-

played on your handset screen.

2 The caller has asked the network provider for

his number to be identified (CLI).

appears in the display if you have

not

requested Calling Line Identification,

Withheld appears if the caller has withheld CLI, and

Unavailable appears if CLI has not been requested.

Switch to mute

You can mute your handset when making external

calls. Your caller can no longer hear you.

Press the "Microphone off" key m during the call to

activate/deactivate the function.

Handsfree talking

To activate while dialling:

Enter the number ~ and press the handsfree

key

Switching between earpiece and handsfree

mode:

During a call press the handsfree key m to activate

or deactivate handsfree talking.

During a call, use t to activate the menu for set-

ting the handsfree volume and use u to set the

volume.

Using the directory and lists

Directory

To open the directory: press h.

You can store up to 80 numbers (max. 32 digits)

and

associated names (max. 14 characters).

Enter

letters/characters ¢ page 11.

Saving the first number in the directory

h ¢ New Entry? ¢ OK

¢ ~ (enter number) ¢ OK

¢ ~ (enter name) ¢ OK

Storing a number in the directory

h ¢ MENU ¢ New Entry ¢ OK

¢ ~ (enter number) ¢ OK

¢ ~ (enter name) ¢ OK

Selecting a directory entry

Open the directory with h. You have the following

options:

◆ Use u to scroll through the entries until the

required name is selected.

◆ Enter the first character of the name and scroll

to the entry with

u, if required.

Dialling with the directory

h ¢ u (select entry) ¢ c

Using other functions

h ¢ u (select entry) ¢ MENU

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

The following functions can be selected with u:

Using shortcut keys

You can assign directory entries to the keys 0 and

2–9:

h ¢ u (select entry) ¢ MENU ¢ Shortcut ¢ OK

¢ ~ (press the key you want to assign the entry to)

To dial, press and hold the required shortcut key.

Transferring the directory to another handset

Requirements:

◆ The sending and receiving handsets must both

be registered to the same base station.

◆ The other handset and the base station can

send and receive directory entries.

h ¢ u (select entry) ¢ MENU ¢ Send Entry /

Send List ¢ OK ¢ ~ (enter the internal number of

the receiving handset) ¢ OK

Last number redial list

This list contains the ten last dialled numbers.

Dialling from the last number redial list

c (press briefly) ¢ u (select entry) ¢ c

Managing entries in the last number redial list

c (press briefly) ¢ u (select entry) ¢ MENU

You can select the following settings:

Calls list/voicemail (network mailbox) list

An advisory tone sounds and the message key

flashes as soon as a new entry appears in the calls

list/voicemail list. A message appears in the dis

play.

When you press the f key, all the lists are dis-

played. If only one list contains new messages,

this

will be opened automatically.

Calls list

Precondition: CLIP (¢ page 7)

Depending on the type of list set, the calls list con-

tains (¢ page 13)

◆ answered calls

◆ missed calls

Depending on the type of list set, all numbers of

the last 25 incoming calls are saved or just the

missed calls are saved.

The calls list is displayed as follows:

Number of new entries + number of old, read entries

Open the calls list

f ¢ CallsList 01+02 ¢ OK

The last incoming call is displayed.

If necessary, use u to select another entry.

Using other functions

u (select entry) ¢ MENU

The following functions can be selected with u:

Calling back a caller from the calls list

f ¢ CallsList 01+02 ¢ OK ¢ u (select entry)

¢ c

New Entry

Save new phone number.

Show Number

Display the phone number.

Use Number

Edit or add to the number.

Then

dial or select other

functions from the

MENU.

Edit Entry

Edit selected entry.

Delete Entry

Delete selected entry.

Send Entry

Send a single entry to another

handset

(¢ page 8).

Delete List

Delete all directory entries.

Send List

Send the complete list to

another handset

(¢ page 8).

Shortcut

For shortcuts, assign the cur-

rent entry to a key.

Use Number

Edit or add to the number.

Then

dial or select other

functions from the

MENU.

Copy to Dir.

Copy an entry to the directory.

Delete Entry

Delete selected entry.

Delete List

Delete all entries.

Please note:

If calls are saved in the network mailbox, you will

receive a message if the appropriate settings have

been set (depending on your network provider).

Delete Entry

Delete current entry.

Copy to Dir.

Copy an entry to the directory.

Date/Time

Call date and time (if set).

Status

New Call: new missed call.

Old Call: entry already read.

Answ.: call taken.

Show Name

If you have requested CNIP,

you

can view the name and

town

that are registered for this

phone number with your

network provider.

Delete List

Warning! All old and new

entries will be deleted.

CallsList 01+02

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

Assigning key 1 for fast access to the

network mailbox

Simply press and hold key 1 on the handset and

you will be connected directly to the network mail

box.

See Menu tree ¢ page 12.

Locating a handset ("paging")

You can locate your handset using the base station.

◆ Briefly press the registration/paging key on the

base station

(¢ page 1).

◆ All handsets will ring simultaneously ("pag-

ing"), even if the ringer tones are deactivated.

End paging: briefly press the registration/paging

key on the base station

(¢ page 1) or the

talk key c on a handset.

Registering handsets

You can register up to four handsets on your base

station (Twist 300) recommended).

For automatic registration of handsets to Twist 300

¢ page 5.

Manual registration of handsets to Twist 300

1. On the handset: MENU ¢ Settings ¢ OK

¢ Handset ¢ OK ¢ Register HS ¢ Enter the sys-

tem PIN of the base station (default is 0000) ¢ OK.

Registering flashes in the display.

2. On the base station: within 60 seconds of

entering the system PIN, press and hold the regis

tration/paging key (¢ page 1) (min. 3 seconds).

Registration takes approx. 1 minute.

De-registering handsets

Handsets can only be de-registered by resetting

the base station to its default settings. This will

also reset other settings

¢ page 10.

If you have only registered handsets for other GAP-

compatible devices, these can only be de-regis

tered with a hardware reset ¢ page 10.

Using several handsets

Making internal calls

Internal calls are free calls to other handsets that

are registered to the same base station.

To make a call to other handsets, press

◆ INT ¢ ~ (1...4, enter internal number of the

handset), the handset is called or

◆ INT ¢ star key P, all handsets are called.

When a participant answers you can speak to

them. To end the call, press the end call key

Internal consultation call/connecting

a call

You are in conversation with an external partici-

pant. Press the INT key and call one or all handsets.

The external participant hears the hold music.

◆ Before the internal participant has answered,

press the end call key

a; the call is diverted to

the participant who answers the call.

◆ After the internal participant has answered,

you can talk to him. Press the end call key

the call is diverted, or press the display key

”;

you are reconnected to the external participant.

Listening in to an external call

You are conducting an external call. An internal

participant can listen in on this call and take part in

the conversation (conference).

Precondition: The Listening in function must be

activated.

Activating/deactivating listening in

MENU ¢ Settings ¢ OK ¢ Base ¢ OK

¢ Listening in ¢ OK (‰ = on)

Internal listening in (conference)

You want to listen in to an existing external call.

Press and hold the c key. You can listen in to the

call. All participants hear a signal tone.

To end: press the end call key a. All participants

hear a signal tone.

If the first internal participant presses the end call

key

a, the handset that has "listened in" remains

connected to the external participant.

Please note:

Each additional handset must be registered on

the base station in order for it to work properly!

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

Setting the alarm clock

Activating/deactivating the alarm clock

MENU ¢ Alarm Clock ¢ OK ¢ Activation

¢ OK (‰ = on)

When activated:

¢ Set the wake-up time ¢ OK

When the alarm clock rings, press any key to switch

it off for 24

hours. If the alarm clock is set, the

wake-up icon

l will appear on the screen and the

wake-up time will be displayed instead of the date.

Setting the wake-up time

MENU ¢ Alarm Clock ¢ OK ¢ Wake-up time ¢ OK

Enter the wake-up time in hours and minutes, then

press

OK.

Phone settings

For details on how to set audio settings, see Menu

tree

¢ page 12.

For details on how to set the system PIN on the

base station, see the Menu tree

¢ page 13.

Changing the display language

MENU ¢ Settings ¢ OK ¢ Handset ¢ OK

¢ Language ¢ OK ¢ select the language ¢ OK

The current language is indicated by ‰ .

If you accidentally choose a language you do not

understand:

MENU ¢ 4 2 1 (press the keys one after the other)

Select the correct language with u and press OK.

Resetting the handset

You can reset individual settings and changes that

you have made. Entries in the directory, the calls

list and the handset's registration to the base sta

tion will be retained.

MENU ¢ Settings ¢ OK ¢ Handset ¢ OK

¢ Reset Handset ¢ OK

Cancel the reset with a.

Restoring the base station to the factory

settings

When restoring factory settings:

◆ All handsets are de-registered

◆ Individual settings are reset

◆ All lists are deleted

◆ The system PIN is reset to the original code

0000

Only the date and time are retained.

Software reset

MENU ¢ Settings ¢ OK ¢ Base ¢ OK

¢ Base Reset ¢ OK

Hardware reset

Disconnect the power cord from the base station.

Hold down the registration/paging key

(¢ page 1) on the base station while reconnect-

ing the power cable to the base station. Release

the key after approximately 5 seconds.

Repeater mode

With a repeater you can increase the range of your

base station. You will need to activate repeater

mode

(¢ page 13). Repeater mode and Eco mode

or Eco mode+ (¢ page 1) cancel each other out.

Operating the base station on

the

PABX

The following settings are only necessary if your

PABX requires them, see the user guide for your

PABX.

When entering the digits, enter them slowly one

after the other.

Changing the dialling mode

MENU ¢ 4 I O 1 1 ¢ The number for the set dial-

ling mode flashes: 0 = touch tone dialling (DTMF);

1 = dial pulsing (DP) ¢ enter number ¢OK.

Setting recall

MENU ¢ 4 I O 1 2 ¢ The number for the current

recall flash

es: 0 = 80 ms; 1 = 100 ms; 2 = 120 ms;

3 = 400 ms; 4 = 250 ms; 5 = 300 ms; 6 = 600 ms;

7 = 800 ms ¢ enter number ¢ OK.

Changing pause after line seizure

You can set the length of the pause inserted

between pressing the talk key

c and sending the

phone number.

MENU ¢ 4 I O 1 O ¢ The number for the current

pause length flashes: 1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.

¢ enter number ¢ OK.

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

Changing the pause after the recall key

MENU ¢ 4 I O 1 4 ¢ The number for the current

pause length flashes: 1 = 800 ms; 2 = 1600 ms;

3 = 3200 ms ¢ enter number ¢ OK.

Appendix

Entering letters/characters

Press the relevant key the number of times indi-

cated.

Briefly press the hash key # to switch from

"Abc" to "123" mode, from "123" to "abc" mode and

from "abc" to "Abc" mode.

Standard characters

1) Space

Specifications

Recommended batteries

Technology: Nickel-metal-hydride (NiMH)

Size: AAA (Micro, HR03)

Voltage: 1.2 V

Capacity: 400–800 mAh

The handset is supplied with recommended batter-

ies.

Base station power consumption

General specifications

Questions and answers

The table below contains a list of common prob-

lems and possible solutions.

Gigaset Communications

GmbH

www.gigaset.com/docs

1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x

1 £ $ ¥ ¤

a b c 2 ä á à â ã ç

d e f 3 ë é è ê

g h i 4 ï í ì î

j k l 5

m n o 6 ö ñ ó ò ô õ

p q r s 7 ß

t u v 8 ü ú ù û

w x y z 9 ÿ ý æ ø å

. , ? ! 0 + - : ¿ ¡ " ’ ; _

* / ( ) < = > %

Abc

-->

123

-->

abc

# @ \ & §

In standby mode

– Handset in base station

– Handset outside base station

approx. 1.3 W

During a call approx. 1.5 W

DECT standard is supported

GAP standard is supported

Range up to 300 m outdoors

up to 50 m indoors

Base station power supply 230 V ~/50 Hz

Environmental conditions

operation

+5°C to +45°C, 20% to

75%

relative humidity

Problem Cause Solution

Nothing

appears in the

display.

The handset is not

switched on.

The batteries are

flat.

Press the end call

key a for approx.

seconds or place

the handset in the

base station.

Charge or replace the

batteries.

No wireless

connection to

the base sta

tion, Base

flashes in the

display.

The handset is

outside the range

of the base sta

tion.

The handset is not

registered.

The base station is

not turned on.

Move the handset

closer to the base

station.

¢ page 9.

Check the mains

connector on the base

station

¢ page 3.

You cannot

hear a ringer/

dialling tone

from the fixed

line network.

The phone cord

supplied has not

been used or has

been replaced by

a new cord with

the wrong jack

connections.

Please always use the

phone cord supplied

or ensure that the

connections are

correct when purchas

ing from a retailer:

3-4 assignment of

telephone leads/EURO

CTR37.

Error tone

sounds after

system PIN

prompt.

PIN forgotten.

You have entered

the wrong

system

PIN.

Reset the system PIN

to the default 0000

¢ page 10.

All handsets are de-

registered. All set

tings are reset. All

lists are deleted.

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

Menu tree

Your phone has an extensive range of features.

These are offered in the form of menus.

To select a function while the phone is in idle sta-

tus, press MENU (open menu), use the t and v

keys to scroll to the function you require and press

OK to confirm.

To return to idle status: press and hold the a

key.

As an alternative to selecting functions using the

t and v buttons, you can also enter the digit

combination that is in front of the function in the

menu tree.

For setting the time and date, for example:

MENU ¢ 4 1 ¢ OK

1 Alarm Clock

1-1 Activation Activating/deactivating the alarm clock

1-2 Wake-up time Input format: HHMM

2 Audio Settings

2-1 Handset Vol-

ume

2-1-1 Earpiece Can be set to one of 3 levels

2-1-2 Speaker Can be set to one of 5 levels

2-2 Ringer Volume 5 levels + "crescendo" available

2-3 Ringer Melody 2-3-1 External Calls 10 ringer melodies available for external calls

2-3-2 Internal Calls 10 ringer melodies available for internal calls

2-3-3 Alarm Clock 10 ringer melodies available for alarm clock

2-4 Advis. Tones Activate/deactivate

2-5 Battery Low 2-5-1 Off Warning tone to indicate

battery is almost flat:

never

2-5-2 On always

2-5-3 During Call only during a call

3 Voice Mail

3-1 Set Key 1

(all devices)

3-1-1 Netw. Mailbx Assign key 1 with network mailbox and enter the network mailbox

number (in idle status, press and hold key

1 to dial).

Netw. Mailbx: your network provider's answer machine; must be

requested separately. The network mailbox list can be displayed if

your network provider supports this function and if key

1 has been

assigned with the network mailbox.

Twist 300 / Belgacom EN / A31008-M2042-E151-1-2M19 / main.fm / 12.08.2009

4 Settings

4-1 Date/Time Enter date (DDMMYY format), then time (HHMM format)

4-2 Handset 4-2-1 Language Set the display language ¢ page 10

4-2-2 Auto Answer Automatically activate/deactivate auto answer ¢ page 7

4-2-3 Register HS Manually register the handset ¢ page 9

4-2-4 Reset Handset Reset the handset ¢ page 10

4-3 Base 4-3-2 Call list type 4-3-2-1 Missed Calls ¢ page 8

4-3-2-2 All Calls ¢ page 8

4-3-3 System PIN Change system PIN (default is 0000)

4-3-4 Base Reset Restore factory settings ¢ page 10

4-3-5 Additional 4-3-5-1 Repeater activate/deactivate ¢ page 10

4-3-5-2 Eco Mode+ activate/deactivate ¢ page 2

4-3-5-3 Eco Mode activate/deactivate ¢ page 2

4-3-6 Listening in Activate/deactivate the function ¢ page 9

BELGACOM twist 300 User manual

Brand: BELGACOM

Model: twist 300

Category: Telephones

Type: User manual

Download PDF

report

in other languages

italiano: BELGACOM twist 300 Manuale utente

BELGACOM twist 300 User manual

BELGACOM twist 300 User manual

in other languages

Related papers

Other documents