Supermicro PDSLA-B Datasheet

PDSLA

PDSLE

USER’S MANUAL

Revision 1.1b

Manual Revision 1.1b

Release Date: Aug. 7, 2007

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

SUPER MICRO COMPUTER reserves the right to make changes to the product described in this

manual at any time and without notice. This product, including software, if any, and documenta-

tion may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any

medium or machine without prior written consent.

IN NO EVENT WILL SUPER MICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE

OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER SHALL NOT

HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE

PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING

OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B

digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

manufacturer’s instruction manual, may cause interference with radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, you are encouraged to try to correct the interference by one or more of

the following measures:

*Reorient or relocate the receiving antenna.

*Increase the separation between the equipment and the receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

*Consult the dealer or an experienced radio/television technician for help.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Preface

About This Manual

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of

the

PDSLA/PDSLE motherboard. The PDSLA/PDSLE supports a single

Intel Pentium

®

D/Pentium

®

4/Celeron Processor in the 775-Land Grid Array Pack-

age at a system bus speed of 1066/800/533 MHz. The Intel Pentium

®

D/Pentium

®

4/Celeron Processor in the 775-Land Grid Array Package is housed in a Flip-Chip

Land Grid Array (FC-LGA4) package that interfaces with the motherboard via an

LGA775 socket. The package consists of a processor core mounted on a substrate

land-carrier. An integrated heat spreader (IHS) is attached to the package substrate

and core and serves as the contacting surface for processor component thermal

solutions, such as a heatsink. Please refer to the motherboard speciﬁ cations pages

on our web site (http://www.supermicro.com/Products) for updates on supported

processors. This product is intended to be professionally installed.

Manual Organization

Chapter 1 includes a checklist of what should be included in your mainboard box,

describes the features, speciﬁ cations and performance of the PDSLA/PDSLE main-

board and provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices. Read

this chapter when installing the processor and DDR 2 memory modules and when

mounting the mainboard in the chassis. Also refer to this chapter to connect the

ﬂ oppy and hard disk drives, the IDE interfaces, the parallel and serial ports, the

mouse and keyboard and the twisted wires for the power supply, the reset button,

the keylock/power LED and the speaker.

If you encounter any problems, see Chapter 3, which describes troubleshoot-

ing procedures for the video, the memory and the setup conﬁ guration stored in

CMOS. For quick reference, a general FAQ (Frequently Asked Questions) section

is provided. Instructions are also included for contacting technical support. In ad-

dition, you can visit our web site at www.supermicro.com/techsupport.htm for more

detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed information on

running the CMOS Setup utility.

Appendix A provides BIOS POST Messages.

Appendix B lists BIOS POST Codes.

Preface

iii

PDSLA/PDSLE User’s Manual

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist ..................................................................................................... 1-1

Contacting Supermicro ............................................................................... 1-2

PDSLA/PDSLE Image ............................................................... 1-3

PDSLA/PDSLE Layout ............................................................... 1-4

PDSLA/PDSLE Quick Reference ................................................ 1-5

Intel 945G/P Chipset: System Block Diagram ........................................... 1-6

Motherboard Features .............................................................................. 1-7

1-2 Chipset Overview ........................................................................................... 1-9

1-3 PC Health Monitoring ................................................................................... 1-10

1-4 Power Conﬁ guration Settings ....................................................................... 1-11

1-5 Power Supply ............................................................................................... 1-12

1-6 Super I/O ........................................................................................................ 1-13

Chapter 2: Installation

2-1 Static-Sensitive Devices ................................................................................. 2-1

2-2 Processor and Heatsink Installation ............................................................... 2-2

2-3 Mounting the Motherboard in the Chassis ..................................................... 2-5

2-4 Installing DDR 2 Memory ............................................................................... 2-6

2-5 I/O Port/Front Control Panel Connector Locations ........................................ 2-7

2-6 Connecting Cables ......................................................................................... 2-8

Power Supply Connectors ...................................................................... 2-8

Power On Connector ................................................................................ 2-9

Reset Connector ...................................................................................... 2-9

Overheat/Fan Fail LED ......................................................................... 2-10

NIC1 LED Connector .............................................................................. 2-10

HDD LED ................................................................................................. 2-11

Power_LED Connector ............................................................................ 2-11

Serial Ports ............................................................................................. 2-12

CD Header/Aux Audio Header ............................................................... 2-12

iv

v

FP Audio .................................................................................................. 2-13

Ethernet Port ............................................................................................ 2-13

Fan Headers ............................................................................................. 2-14

Chassis Intrusion ...................................................................................... 2-14

ATX PS/2 Keyboard/Mouse Ports ......................................................... 2-15

Universal Serial Bus (USB) ..................................................................... 2-15

Wake-On-Ring .......................................................................................... 2-16

Wake-On-LAN .......................................................................................... 2-16

VGA Connector ........................................................................................ 2-17

AC'97 Output ............................................................................................ 2-17

2-7 Jumper Settings ............................................................................................ 2-18

Explanation of Jumpers ......................................................................... 2-18

CMOS Clear ........................................................................................... 2-18

USB Wake-Up .......................................................................................... 2-19

Watch Dog Enable/Disable ...................................................................... 2-20

Gigabit LAN Enable .................................................................................. 2-20

SMBus to PCI/PCI-Express Slots ............................................................ 2-21

Speaker Connector .................................................................................. 2-21

CPU Front Side Bus Speed ..................................................................... 2-22

2-8 Onboard LED Indicators ................................................................................ 2-23

GLAN LEDs .............................................................................................. 2-23

Power LED ................................................................................................ 2-23

2-9 Parallel Port, Floppy/Hard Drive and Audio Connections ............................ 2-24

Parallel Port Connector ........................................................................... 2-24

Floppy Connector ................................................................................... 2-25

IDE Connector .......................................................................................... 2-25

2-10 Installing the Operating System and Software Programs ............................. 2-26

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ....................................................................................... 3-1

No Power ................................................................................................... 3-1

No Video .................................................................................................. 3-1

Memory Errors ........................................................................................... 3-2

Losing the System’s Setup Conﬁ guration ................................................ 3-2

3-2 Technical Support Procedures ....................................................................... 3-2

3-3 Frequently Asked Questions .......................................................................... 3-3

3-4 Returning Merchandise for Service ................................................................. 3-5

Table of Contents

PDSLA/PDSLE User’s Manual

Chapter 4: BIOS

4-1 Introduction ....................................................................................................... 4-1

4-2 Running Setup ................................................................................................. 4-2

4-3 Main BIOS Setup ............................................................................................. 4-2

Main BIOS Setup Menu ........................................................................... 4-3

4-4 Advanced BIOS Setup ...................................................................................... 4-5

4-4.1 Advanced BIOS Features ................................................................ 4-5

4-4.2 Advanced Chipset Control ............................................................... 4-6

4-4.3 I/O Device Conﬁ guration .................................................................. 4-8

4-4.4 PnP Conﬁ guration .......................................................................... 4-10

4-4.5 Hardware Monitors ......................................................................... 4-11

4-4.6 Processor & Clock Options ............................................................ 4-11

4-5 Security ........................................................................................................... 4-12

4-6 Boot ............................................................................................................... 4-13

4-7 Exit ................................................................................................................. 4-15

Appendices:

Appendix A: BIOS POST Messages .........................................................................A-1

Appendix B: BIOS POST Codes ................................................................................B-1

vi

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

All Included in the retail box only

One (1) Supermicro Mainboard

Two (2) SATA cables

One (1) IDE cable

One (1) ﬂ oppy drive ribbon cable

One (1) I/O shield

One (1) Supermicro CD containing drivers and utilities

One (1) User's/BIOS Manual

1-2

PDSLA/PDSLE User’s Manual

Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Paciﬁ c

Address: SuperMicro, Taiwan

4F, No. 232-1 Liancheng Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 1: Introduction

1-3

Figure 1-1. PDSLA/PDSLE Image

An Important Note to the User

• All images and layouts shown in this manual are based upon the latest PCB

Revision available at the time of publishing of this manual. The motherboard

you've received may or may not look exactly the same as the ones shown in

this manual.

1-4

PDSLA/PDSLE User’s Manual

Figure 1-3. Motherboard Layout

(not drawn to scale)

Important Notes to the User

• All images and layouts shown in this manual were based upon the latest PCB

Revision available at the time of publishing of the manual. The motherboard

you've received may or may not look exactly the same as the ones shown in

this manual.

• See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front panel

connections.

• " " indicates the location of "Pin 1".

• The only difference between the PDSLA and PDSLE is that the PDSLA has

Internal VGA.

S

UPER DSLA/PDSLE

PCI-E x1

®

LGA 775 Processor

KB/MS

Parallel Port

COM1

VGA

USB

3/4/5/6

USB1/2

JFUSB1

Fan3

Clock

945G/P

(Lakeport)

North Bridge

PCI-E x16

LAN

CTRL

JPL1

GLAN Enable

CD inAux.In

AC97

COM2

BIOS

CL CMOS

JL1

WOL

I-SATA0

FP

CTRL

Fan 2

JF 1

Buzzer

I

DE

24-Pin ATX PW R

Su

p

e

r

I/

O

F/P USB7/8

ICH7

J9

DIMM#1A

DIMM#2A

DIMM#1B

DIMM#2B

Floppy

Audio

JBT1

J3

J2 7

J40

South Bridge

J13

J45

J11

J44

JG1

J31

J30

Battery

PCI#4

-33MHz

4-Pin ATX PWR

J41

J28

JPUSB1

JFUSB2

J

7

J1

PCI-E x1

J

8

PC

I4

PCI#3 -33MHz

PC

I3

PC

I2

PCI#2-33MHz

PCI#1-33MHz

PC

I

1

JP

1

JP

2

J

PU

SB

2

F/P USB Wake- up

J43

I-SATA1

I-SATA2

I-SATA3

D2

4

JWD

JLED

LE 1

J

WO

R

RJ45

Fan1/CPU

Slot#1

Slot#2

Slot#3

Slot#5

Slot#4

Slot#6

Slot#7

FP Aud

J12

(*PDSLA )

Chapter 1: Introduction

1-5

PDSLA/PDSLE Quick Reference

Jumpers Description Default Setting

J9 Buzzer/Speaker Enable

Pins 3-4 (Enabled)

JBT1 CMOS Clear (*See Chapter 2)

JFSB1/JFSB2 CPU Frequency Pins 1-2/Pins 1-2 (Auto)

JP1/JP2 PCI/PCI-E SMB Open/Open (Disabled)

JPL1 Giga-bit LAN Enable Pins 1-2 (Enabled)

JPUSB1 B/P USB Wake Up Pins 2-3 (Disabled)

JPUSB2 F/P USB Wake Up Pins 2-3 (Disabled)

JWD Watch Dog Pins 1-2 (Reset)

Connectors Description

ATX PWR (J40) ATX 24-Pin Power Connector

4-Pin ATX PWR (J41) 12V 4-pin Power Connector (*required)

Audio (J45) Audio Port

AUX-In (AUX1) Auxiliary (Audio) Input Header

CD-In (CD1) Audio CD Input Header

Chassis Intrusion(JL1) Chassis Intrusion Header

COM1 (J31), COM2 (J13) COM Port/Serial Port 1 & Port 2 Connectors

DIMM#1A,#2A,#1B,#2B Memory (DIMM) Slots (1 through 4)

Fans 1-3 Fan1: CPU Fan, Fan2/3: Chassis Fan Headers

Floppy (J27) Floppy Disk Connector

FP Audio (J12) Front Panel Audio Connector (*See Chapter 2)

FP Control Panel (JF1) Front Control Panel Header

LAN Port (J11) Ethernet RJ45 (Gigabit LAN) Connector

IDE (J3) IDE Connector

I-SATA #0-3 (J2,J4,J5,J6) Intel SATA (#0-3) Headers

KB/Mouse (J28) PS/2 Keyboard/Mouse

LE1 Standby Warning LED Indicator

PWR LED (JLED) Power LED Indicator

Printer (J30) Parallel Printer Port

Slot 1-Slot 4 PCI 33 MHz (PCI #1-#4)

Slot 5 PCI-Express x1 (using x 8 slot)

Slot 6 PCI-Express x16

Slot 7 PCI-Express x1

Speaker (J9) Speaker Header

USB 1/2 (J11) (Back Panel) Universal Serial Ports 1-2

USB 3/4/5/6 (J44) (Back Panel) Universal Serial Ports 3-6

USB 7/8 (J43) (Front Panel) USB ports 7/8

VGA (JG1) Video/Graphic Connector (*For PDSLA only)

WOL (WOL) Wake-On-LAN Header

WOR(JWOR) Wake-On-Ring Header

1-6

PDSLA/PDSLE User’s Manual

Figure 1-3. 945G/P Lakeport Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the following pages for the

actual speciﬁ cations of each motherboard.

LAKEPORT

SLOTS

LGA775_PROCESSOR

ICH-7

USB

PORT_0~7

FWH

LPC I/O

MS.

KB. FDD. SER.1

SER.2

PRN.

PRI_IDE

VRM 10.1

ADDR

CTRL

DATA

UDMA/100

LPC

PCI_32_BUS

DDR2_667/533/400

VRM V10.1

DMI

4_PCI_x32

DIMM_CHA

S-ATA/300

4 x SATA

CK410 CLK

1 PCIE_x16

GRAPHIC

945G/P

DIMM_CHB

PORTS

PCIE_x16

INTEGRATED

GRAPHIC

82573 LAN

SLOTS

1_PCIE_x1

PCIE_x1

W83627HG 5.1-CH

AUDIO

FSB: 1066/800/533MHz

LPCUSB 2.0/1.1

AC97

PCIE_x1

1_PCIE_x8

SLOTS

(945G only)

Chapter 1: Introduction

1-7

Motherboard Features

CPU  Latest CPU technology!

• Single Intel Pentium

®

D/Pentium

®

4/Celeron Dual Core in the 775-Land Grid

Array Package at a system bus speed of 1066/800/533 MHz.

• Supports Intel Hyper-Threading Technology.

Memory  Latest memory technology!

• Supports unbuffered, non-ECC single or dual channel DDR2 with the bandwidth

up to 5.3GB/s (DDR2 667) for single channel mode and 10.7 GB/s (DDR2 667) in

dual-channel Interleaved mode.

Note: See Section 2-4 for details.

Chipset  Latest Intel chipset technology!

• Intel Lakeport 945G/P chipset

Expansion Slots

• One (1) PCI-Express x16 (intended for graphics)

• One (1) PCI-Express x8 (PCI-Express x1 Signal)

• One (1) PCI-Express x1

• Four (4) 32-bit PCI 33MHz (5V)

BIOS

• 4 Mb Firmware Hub AwardBIOS

®

Flash BIOS

• APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0, Plug and Play (PnP)

PC Health Monitoring

• Onboard voltage monitors for Chipset Core +1.5V, CPU core, +3.3V, +3.3V

standby, +5V, +5V Standby, Vbat (battery voltage) and ±12V

• Fan status monitor with ﬁ rmware 4 pin fan speed control

• Fan Fail Alert LED and Beep

• SuperDoctor III, Watch Dog, NMI

• Environmental temperature monitoring via BIOS

• Power-up mode control for recovery from AC power loss

• System overheat LED and control

• System resource alert via Supero Doctor III

• Auto-switching voltage regulator for the CPU core

ACPI Features

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Main switch override mechanism

• External modem ring-on

1-8

PDSLA/PDSLE User’s Manual

Onboard I/O

• 1 ATA/100 EIDE Channels for a total of two IDE devices backward compatible

• Built in ICH7 SATA Controller, 4 connectors for 4 devices (300MB/S)

• 1 ﬂ oppy port interface (up to 2.88 MB)

• 2 Fast UART 16550 compatible serial ports

• Intel 82573V Gigabit Ethernet Controller

• 1 EPP (Enhanced Parallel Port) and ECP (Extended Capabilities Port) sup-

ported parallel port

• PS/2 mouse and PS/2 keyboard ports

• Up to 8 USB (Universal Serial Bus) 2.0 ports for a speed of up to 480Mbps

 Latest USB 2.0 technology!

• AC'97 audio high quality 6-channel sound

• Integrated gfx core graphics on board (*PDSLA Only)

Other

• Wake-on-LAN

• Wake-on-Ring (WOR)

• System Bus Clock Frequency Selection (Overclocking) Support (*Note)

• Suspend-to-RAM

• Onboard +5V Standby Power Warning LED ("LE1")

• Pb Free

CD Utilities

• BIOS ﬂ ash upgrade utility

• Drivers and software for Intel 945G/P chipset utilities

Dimensions

• ATX form factor, 11.5" x 9.5" (292 x 242 mm)

Note: Please be aware of the following conditions when "over

clocking" is used:

Setting a high CPU FSB Speed (overclocking), using a DRAM

Frequency, or selecting a high CPU V-Core voltage, memory voltage, chipset

voltage, ICH chipset voltage, or FSB termination voltage may result in system

instability. If this occurs, reset the setting to the default setting. In addition, extra

fans may be needed for proper system cooling. The PDSLA/PDSLE offers the

option of "overclocking"; however, Supermicro is not responsible for any damage

caused by the use of overclocking.

Chapter 1: Introduction

1-9

1-2 Chipset Overview

Intel’s Lakeport (945G/P) chipset consists of two primary components: the Graphics

Memory Controller Hub (GMCH)/Memory Controller Hub (MCH) and the I/O Control-

ler Hub (ICH7). Optimized for the Celeron, Pentium 4, Pentium D processors in an

LGA775 Package, the Lakeport (945G/P) provides the performance and feature-set

required for high-end UP dual core processor desktop solutions.

Graphics Memory Controller Hub (GMCH)/Memory Controller

Hub (GMCH)

The GMCH/MCH supports high-performance integrated graphics and manage the

data ﬂ ow of the following ﬁ ve interfaces: the CPU interface, DDR2 interface, PCI

Express Graphic Interface, the DMI (Direct Media Interface) and integrated graphics

with display interfaces (*GMCH only) . The GMCH/MCH supports a FSB frequency

of 533/800/1066 MHz using a scalable CPU. It supports up to two channels of

non-ECC DDR2 400/533/667 SDRAM. The integrated Graphics Controller provides

3D, 2D and display capabilities. The GMCH/MCH also supports advanced desktop

power management.

Intel ICH7 System Features

The ICH7 provides extensive I/O support to a high-end 945G/P system. Functions

and capabilities include:

*PCI Express Base Speciﬁ cation, Rev. 1.0a-compliant

*PCI 2.3 with support for 33 MHz PCI operations

*ACPI Power Management Logic Support

*Integrated Serial ATA host controller with independent DMA operation on four ports,

(with support of SATA I and SATA II HDD)

*Integrated IDE controller supports Ultra ATA 100/66/33

*USB host interface with support for eight USB ports

*Enhanced DMA Controller, interrupt controller, and timer functions

*System Management Bus (SMBus) 2.0 with additional support for I

2

C devices

*Low Pin Count (LPC) Interface

*Firmware Hub (FWH) Interface

*Audio Codec '97 Rev. 2.3 which provides a link for Audio (up to 6 channels)

1-10

PDSLA/PDSLE User’s Manual

1-3 PC Health Monitoring

This section describes the PC health monitoring features of the PDSLA/PDSLE.

The motherboard has an onboard System Hardware Monitor chip that supports

PC health monitoring.

Recovery from AC Power Loss

BIOS provides a setting for you to determine how the system will respond when

AC power is lost and then restored to the system. You can choose for the system

to remain powered off (in which case you must hit the power switch to turn it back

on) or for it to automatically return to a power on state. See the Power Lost Con-

trol setting in the BIOS chapter of this manual to change this setting. The default

setting is Last State.

Onboard Voltage Monitors for the CPU Core, Chipset Core +1.5V,

+3.3V, +3.3V standby, +5V, +5V Standby, Vbat and ±12V

The onboard voltage monitor will scan these voltages continuously. Once a voltage

becomes unstable, it will give a warning or send an error message to the screen.

Users can adjust the voltage thresholds to deﬁ ne the sensitivity of the voltage

monitor by using SD III.

Fan Status Monitor with Software

The PC health monitor can check the RPM status of the cooling fans via Supero

Doctor III.

Fan Fail Alert

When a fan fails during the normal operation, the Fan Fail LED will start to blink

and the buzzer will be activated to indicate a fan failure.

CPU Overheat LED and Control

This feature is available when the user enables the CPU overheat warning function

in the BIOS. This allows the user to deﬁ ne an overheat temperature. When this

temperature reaches the pre-deﬁ ned threshold, the CPU thermal trip feature will be

activated and it will send a signal to the Speaker LED and, at the same time, the

CPU speed will be decreased.

Chapter 1: Introduction

1-11

1-4 Power Conﬁ guration Settings

This section describes features of your motherboard that deal with power and

power settings.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will wake-up and the LED will automatically stop blinking and remain on.

BIOS Support for USB Keyboard

If the USB keyboard is the only keyboard in the system, it keyboard will function

like a normal keyboard during system boot-up.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a system

suspend button. When the user presses the power button, the system will enter

a SoftOff state. The monitor will be suspended and the hard drive will spin down.

Pressing the power button again will cause the whole system to wake-up. During

the SoftOff state, the ATX power supply provides power to keep the required circuitry

in the system alive. In case the system malfunctions and you want to turn off the

power, just press and hold the power button for 4 seconds. The power will turn off

and no power will be provided to the motherboard.

Wake-On-Ring (WOR) Header

Wake-up events can be triggered by a device such as the external modem ringing

when the system is in the SoftOff state. Note that external modem ring-on can only

be used with an ATX 2.01 (or above) compliant power supply.

1-5 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates of 1 GHz and faster.

1-12

PDSLA/PDSLE User’s Manual

The

PDSLA/PDSLE accommodates 12V ATX power supplies. Although

most power supplies generally meet the speciﬁ cations required by the CPU, some

are inadequate. A 2-Amp of current supply on a 5V Standby rail is strongly recom-

mended.

It is strongly recommended that you use a high quality power supply that meets

12V ATX power supply Speciﬁ cation 1.1 or above. It is also required that the 12V

4-pin power connection (J41) be used for high-load conﬁ gurations. In areas where

noisy power transmission is present, you may choose to install a line ﬁ lter to shield

the computer from noise. It is recommended that you also install a power surge

protector to help avoid problems caused by power surges.

1-6 Super I/O

The disk drive adapter functions of the Super I/O chip include a ﬂ oppy disk drive

controller that is compatible with industry standard 82077/765, a data separator,

write pre-compensation circuitry, decode logic, data rate selection, a clock genera-

tor, drive interface control logic and interrupt and DMA logic. The wide range of

functions integrated onto the Super I/O greatly reduces the number of components

required for interfacing with ﬂ oppy disk drives. The Super I/O supports two 360

K, 720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data transfer rates of 250 Kb/s,

500 Kb/s or 1 Mb/s.

It also provides two high-speed, 16550 compatible serial communication ports

(UARTs), one of which supports serial infrared communication. Each UART in-

cludes a 16-byte send/receive FIFO, a programmable baud rate generator, complete

modem control capability and a processor interrupt system. Both UARTs provide

legacy speed with baud rate of up to 115.2 Kbps as well as an advanced speed

with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Conﬁ guration

and Power Interface), which includes support of legacy and ACPI power manage-

ment through a SMI or SCI function pin. It also features auto power management

to reduce power consumption.

The IRQs, DMAs and I/O space resources of the Super I/O can be ﬂ exibly adjusted

to meet ISA PnP requirements, which support ACPI and APM (Advanced Power

Management).

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Static-Sensitive Devices

Electric Static Discharge (ESD) can damage electronic com ponents. To prevent

damage to your system board, it is important to handle it very carefully. The following

measures are generally sufﬁ cient to protect your equipment from ESD.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing the board from the antistatic

bag.

• Handle the board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard and peripherals back into their antistatic bags when not in

use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

• Use only the correct type of CMOS onboard battery as speciﬁ ed by the Manufac-

turer. Do not install the CMOS onboard battery upside down to avoid a possible

explosion.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure the person handling it is static protected.

Installation Procedures

Follow the procedures as listed below for full installation of the motherboard into

a chassis:

1. Install the processor and the heatsink to the motherboard.

2. Install the motherboard in the chassis.

3. Install the memory and add-on cards.

4. Finally, connect the cables and install the drivers.

2-2

PDSLA/PDSLE User's Manual

2-2 Processor and Heatsink Installation

When handling the processor package, avoid placing

direct pressure on the label area of the fan.

(*Note: The CPU heatsink is included in Intel's CPU retail package.)

Installation of the LGA775 Processor

IMPORTANT: Always connect the power cord last and always remove it before add-

ing, removing or changing any hardware components. Make sure that you install

the processor into the CPU socket before you install the CPU heatsink.

!

1. Press the socket lever to release

the load plate, which covers the CPU

socket, from its locking position.

Socket Lever

2. Gently lift the socket lever to open

the load plate.

Load Plate

Page is loading ...

Supermicro PDSLA-B Datasheet

This manual is also suitable for

Supermicro PDSLA-B Datasheet

Related papers

Other documents