Smooth Fitness 5.65E User manual

USER’S MANUAL

SMOOTH 5.65E MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 135kgs (300lbs

SERVICE NUMBER: 0800-09 72 100

SERIAL NUMBER (found on frame):

2 SMOOTH 5.65E TREADMILL

PRECAUTIONS

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and

information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

• Use the treadmill only as described in this manual.

• Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the treadmill on any surface that

blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.

• When choosing a location for the treadmill make sure that the location and position permit access to a plug.

• Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or

near water.

• Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the treadmill at all times.

• The treadmill should not be used by persons weighing more than 135gs (300lbs)

• Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the

treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are

recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet,

wearing only stockings, or in sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the

same circuit.

• Always straddle the belt and allow it to start moving before stepping onto the belt.

• Always examine your treadmill before using to ensure all parts are in working order.

• Allow the belt to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your treadmill.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not

operate the treadmill with a damaged or frayed power cord.

• Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by

an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow

these instructions will void the treadmill warranty.

• Never leave the treadmill unattended while it is running.

• The equipment is for Class B (Home Use).

www.smoothfitness.co.uk 3

POWER REQUIREMENTS

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN

ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO

WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE

PRODUCT, IF IT WILL NOT FIT THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges

and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the

possibility of treadmill damage, always use a surge protector (not included) with your treadmill. Surge protectors can be

purchased at most hardware stores.

This treadmill is provided with two different grounding plugs for Central Europe and United Kingdom. Please choose the right

one and plug in your treadmill.

Please make sure that your local voltage is appropriate for the power requirements of this treadmill before you plug it in.

This product is for use with a voltage of 230V ± 5%.

Do not use a voltage transformer with product.

Do not use an extension cord with this product when you are not sure if the product is still properly grounded.

The following pictures show the two delivered plugs:

4 SMOOTH 5.65E TREADMILL

PREASSEMBY

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes. And Compare them to the supplied

components and supplied Hardware lists on pages 5-6 for a full count of the parts included. If you are missing any parts or

have any assembly questions contact us directly at 0800-09 72 100.

Assembly instructions begin on page 18.

Gather your tools:

Before starting the assembly of your unit, make sure that you have gathered all the necessary tools you may require to

assemble the unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick and

hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free

from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable

amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another person

when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 135KG (approx. 300LBS) it is not

recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

1. The safety level can be maintained only if the unit is examined regularly for damage and wear.

2. Replace any defective components immediately and stop all use of equipment until repaired.

3. Always take care when you are mounting the equipment. Straddle the equipment by placing your feet on the straddle

rails. Dismount from the equipment only after all parts have stopped.

4. Always check the quick to wear components like pulley etc. To prevent danger.

5. There is an emergency stop in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill

immediately by pulling the safety key for emergency dismount

www.smoothfitness.co.uk 5

CONTENTS CHECKLIST

Carton contents:

For your convenience, we have identified the contents of the shipping carton. Please check to make sure you

have all of the components before assembly. This chart is provided to help you identify the components used in

the assembly of this product.

No. Description Qty.

A Main Frame Assembly 1

B Handle Bar-L 1

105 Water Bottle Holder 2

207 Handle Bar Cover-LL 1

208 Handle Bar Cover-LR 1

209 Handle Bar Cover-RL 1

210 Handle Bar Cover-RR 1

305

Upright Low Cover - LL

1

306

Upright Low Cover - LR

1

307

Upright Low Cover - RL

1

308

Upright Low Cover - RR

1

6 SMOOTH 5.65E TREADMILL

HARDWARE COMPARISON CHART

Hardware chart:

For your convenience, we have identified the hardware used in the assembly of this product. This chart is

provided to help you identify those items that may be unfamiliar to you.

No. Description Qty.

806

Bolt M8×52mm

2

807

Washer ∮8

6

809 Screw M4×15mm 8

811

Screw M6×12mm

4

812 Bolt M8×12mm 6

813

Curve Washer ∮8

4

814 Bolt M8×55mm 2

824 Nylon Nut M8 2

864 Screw M4×19 4

A

T Handle Hex Key

1

B Wrench 1

C Screwdriver 1

MILLIMETERS

www.smoothfitness.co.uk 7

PARTS LIST

No. Description Qty. Order No.

100

Console Assembly

101 Overlay 1 5.65E-101

102 LCD Computer 1 5.65E-102

105 Water Bottle Holder 2 5.65E-105

106 Console Housing - Upper 1 5.65E-106

107 Console Housing - Bottom 1 5.65E-107

108 Safety Key Base 1 5.65E-108

109 Safety Key 1 5.65E-109

110 2 Pin Safety Key Box Upper Power Wire 1 5.65E-110

112 7 Pin Computer Upper Wire 1 5.65E-112

113 EKG Pulse Wire 2 5.65E-113

200

Handle Bar Assembly

201 Handle Bar 1 5.65E-201

202 Handle Bar Foam Grip 2 5.65E-202

203 Rear Handle Bar - Left 1 5.65E-203

204 Rear Handle Bar - Right 1 5.65E-204

205 Handle Bar Upright Foam Grip 2 5.65E-205

206 Handle Bar End Cap 2 5.65E-206

207 Handle Bar Cover - LL 1 5.65E-207

208 Handle Bar Cover - LR 1 5.65E-208

209 Handle Bar Cover - RL 1 5.65E-209

210 Handle Bar Cover - RR 1 5.65E-210

211 Hand Pulse Sensor 2 5.65E-211

212 Plastic Fixing Insert 10 5.65E-212

215 Front Handle Bar - 2 5.65E-215

216 Handle Bar Foam Grip 1 5.65E-216

300

Upright Assembly

301 Upright 2 5.65E-301

305 Upright Low Cover - LL 1 5.65E-305

306 Upright Low Cover - LR 1 5.65E-306

307 Upright Low Cover - RL 1 5.65E-307

308 Upright Low Cover - RR 1 5.65E-308

8 SMOOTH 5.65E TREADMILL

PARTS LIST

Description Qty. Order No.

400

Base Frame Assembly

401 Base Frame 1 5.65E-401

402 2 Pin Safety Key Box Lower Power Wire 1 5.65E-402

403 7 Pin Computer Lower Wire 1 5.65E-403

404 Power Switch Plate Base 1 5.65E-404

405 Power Switch Plate Cover 1 5.65E-405

406 Power Switch Plate 1 5.65E-406

407 Power Breaker 1 5.65E-407

408 Power Switch 1 5.65E-408

409 Front Caster 2 5.65E-409

410 Base Frame rubber cushion 2 5.65E-410

411 Rubber Cushion 2 5.65E-411

412 Cushion 2 5.65E-412

413 Foot Locker 1 5.65E-413

414 Transportation wheel bracket 1 5.65E-414

415 Transportation wheel 1 5.65E-415

416 Holder 1 5.65E-416

417 Plastic pole 1 5.65E-417

418 Spring 1 5.65E-418

500

Motor Assembly

501 Motor Hood Top 1 5.65E-501

502 Driving Motor 1 5.65E-502

503 Motor Holder 1 5.65E-503

504 Driving Belt 1 5.65E-504

505 Control Board 1 5.65E-505

506 Transformer 1 5.65E-506

507 Elevation Control Board 1 5.65E-507

508 Elevation Support Tube 1 5.65E-508

509 Elevation Support Tube End Cap 4 5.65E-509

510 Elevation Motor 1 5.65E-510

511 Elevation Gear Sleeve 1 5.65E-511

512 Fold Up Locker 1 5.65E-512

513 Fold Up Support 1 5.65E-513

514 Shock 1 5.65E-514

515 Wheel 1 5.65E-515

516 Plastic Clamp - Top 2 5.65E-516

517 Plastic Clamp - Bottom 2 5.65E-517

518 Elevation Support 2 5.65E-518

519 Motor Hood - Left 1 5.65E-519

520 Motor Hood - Right 1 5.65E-520

521 Motor Bottom Cover 1 5.65E-521

www.smoothfitness.co.uk 9

PARTS LIST

600. Running Deck Assembly

601 Running Belt 1 5.65E-601

602 Side Rail 2 5.65E-602

603 Running Deck 1 5.65E-603

604 Side Rail End Cap - Left 1 5.65E-604

605 Side Rail End Cap - Right 1 5.65E-605

606 Rear end cap fixed block 2 5.65E-606

700

Deck Frame Assembly

701 Deck Frame 1 5.65E-701

702 Front Roller Shaft 1 5.65E-702

703 Front Roller Tube 1 5.65E-703

704 Rear Roller Shaft 1 5.65E-704

705 Rear Roller Tube 1 5.65E-705

706 Running Deck Support Tube 1 5.65E-706

707 Running Deck Support Tube Foam Grip 1 5.65E-707

708 Rear Caster 2 5.65E-708

709 Cushion Pad 6 5.65E-709

710 Bottom cover-1 1 5.65E-710

711 Bottom cover-2 1 5.65E-711

800

Fastening

801

Screw M3×16m 8

5.65E-801

803 Screw M3×8mm 2 5.65E-803

804 Screw M4×12 30 5.65E-804

805 Bolt M8×45mm 4 5.65E-805

806 Bolt M8×52m 4 5.65E-806

807

Washer ∮8

11 5.65E-807

809 Screw M4×15 50 5.65E-809

811 Screw M6×12m 4 5.65E-811

812 Bolt M8×12 6 5.65E-812

813

Washer ∮8.5

4 5.65E-813

814 Bolt M8×55mm 2 5.65E-814

816

Washer ∮8

2 5.65E-816

817 M8 C-Clip 2 5.65E-817

818 Bolts M16×102 2 5.65E-818

819 Washer M16×26 2 5.65E-819

821 Screw M3×8mm 2 5.65E-821

822

Bolt ∮8×36

1 5.65E-822

823 Bolt M10×53mm 1 5.65E-823

824 M8 Nylon Nut 11 5.65E-824

825 M10 Nylon Nut 3 5.65E-825

827 Bolt M10x82 1 5.65E-827

828 Bolt M10x88 1 5.65E-828

10 SMOOTH 5.65E TREADMILL

PARTS LIST

No. Description Qty. Order No.

830

Washer ∮10

3 5.65E-830

831 Bushing 10x20.9x26x17.5 2 5.65E-831

832 M4×25mm 4 5.65E-833

833 Bolt M8×36mm 1 5.65E-833

836 Screw M4x19 16 5.65E-836

837 Fixed Bolt M8×68 2 5.65E-837

838

Curve Washer ∮9×35

2 5.65E-838

839

Spring ∮8×26

1 5.65E-839

843 Fixed Bolt M8×48mm 1 5.65E-843

844

Washer ∮10.5

2 5.65E-844

845

Washer ∮8

6 5.65E-845

846 Bolt M8×12mm 6 5.65E-846

847 Nut M8 2 5.65E-848

848 Fixed Bolt M10×115mm 2 5.65E-848

853 Bolt M5×14mm 2 5.65E-853

855 Side Rail Guider 8 5.65E-855

856 Screw M8×25mm 6 5.65E-856

857 Screw M8×55mm 2 5.65E-857

858 Bolt M6×45mm 3 5.65E-858

859

Washer ∮6.5

3 5.65E-859

860 Bolt M10×32mm 1 5.65E-860

863 Bolt M10×45mm 2 5.65E-863

864 Screw M4×19mm 4 5.65E-864

865 Bolt M8×30mm 8 5.65E-865

866 Screw M4x23 2 5.65E-866

867

Spring Washer ∮8x14x2

2 5.65E-867

868

OD30xID9xT3.0

2 5.65E-868

www.smoothfitness.co.uk 11

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

113

112

110

109

108

107

106

105

102

801

101

111

809

803

809

12 SMOOTH 5.65E TREADMILL

216

202

824

812

811

807

812

811

215

807

806

864

807

805

801

806

212

211

210

209

208

207

206

205

204

203

202

201

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

www.smoothfitness.co.uk 13

809

308

307

306

212

305

110

112

301

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

14 SMOOTH 5.65E TREADMILL

419

809

418

417

416

853

401

404

405

406

407

408

409

410

411

412

413

414

415

812

813

814

807

816

817

814

817

818

819

832

821

822

823

825

809

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

www.smoothfitness.co.uk 15

827

830

506

867

844

501

503

502

504

505

507

508

509

510

511

512

513

514

515

516

517

518 518

519

520

521

809

828

825

831

817

830

822

806

824

809

837

838

839

824

843

844

807

846

825

848

809

846

807

809

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

16 SMOOTH 5.65E TREADMILL

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

www.smoothfitness.co.uk 17

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED AT THE FACTORY.

18 SMOOTH 5.65E TREADMILL

ASSEMBLY

STEP 1:

Remove your treadmill from the carton and place it on the floor in an

open area.

Attach the Uprights (301) to the Base Frame and secure each one in

place using two M8×12mm Bolt (812) and two ø8.5 Washer (813), one

M8×55mm Bolt (814) and one ø8 Washer (807).

812

X4

813

X4

807

X2

814

X2

www.smoothfitness.co.uk 19

ASSEMBLY

STEP 2:

Rotate the Console Housing – Bottom （107） up to the correct position and press the Rear

Handle Bar – Left（203） into the Upright - Left （301）as shown. Repeat this procedure on the

Upright – Right.

20 SMOOTH 5.65E TREADMILL

ASSEMBLY

STEP 3:

Secure in place using two M8 × 52mm Bolt (806), two ∮8 Washer (807)

and two M8 Nylon Nut (824). Secure the M8 ×1

2mm Bolt (812) and two

∮8 Washer (807).

806

X2

807

X4

812

X2

824

X2

203

807

806

807

806

812

807

812

824

204

Page is loading ...

Smooth Fitness 5.65E User manual

Smooth Fitness 5.65E User manual

Related papers

Other documents