Comtech EF Data DMD-2050E Operating instructions

MN-DMD2050E Revision 2

Comtech EF Data is an

AS9100 Rev B / ISO9001:2000 Registered Company

DMD-2050E

Universal Satellite Modem

Installation and Operation Manual

IMPORTANT NOTE: The information contained in this document supersedes all previously published information

regarding this product. Product specifications are subject to change without prior notice.

ER-DMD2050E-EA2 Rev - PLM C-0028800

Errata A for MN-DMD2050E Rev 2

Comtech EF Data Documentation Update

Subject:

Chapter 3, Theory of Operation

Errata Part Number:

ER-DMD2050E-EA2 (Errata documents are not subject to revision.)

PLM CO Number:

C-0028800

Comments:

The new information will be included in the next released revision of the manual.

IMPORTANT

Set the modem to Loop Timing mode for these Loopback operations:

 Tx/Rx Terrestrial Loopback

 Tx/Rx Baseband Loopback

 Rx Baseband Loopback

ER-DMD2050E-EA2 Rev - PLM C-0028800

Blank Page

ER-DMD2050E-EB2 Rev - PLM C-0028804

Errata B for MN-DMD2050E Rev 2

Comtech EF Data Documentation Update

Subject:

Chapter 3 and Chapter 4 references to MN-DMDREMOTEOP manual

Errata Part Number:

ER-DMD2050E-EB2 (Errata documents are not subject to revision.)

PLM CO Number:

C-0028804

Comments:

The new information will be included in the next released revision of the manual. See

the following pages.

DMD2050E Universal Satellite Modem User Interfaces

MN-DMD2050E Revision 2 4–31

4.4.6.6 SNMP (menu)

A description of OID organization is provided in the MN-DMDREMOTEOP manual.

SNMP MENU

SNMP VERSION {V1 & V2, V3} This selection controls the SNMP Version that will be used in

messaging between the equipment and it’s host.

When V1 & V2 is used, RD COMMUNITY and RDWR

COMMUNITY are used to determine the authorization of an

incoming message.

When V3 is used, three contexts are supported:

public

,

mib2

, and

dev

. Context, Authentication and Privacy are a portion of each

SNMPV3 message.

The

public

context will only allow the user to see the sysoid of the

unit. This is the most restricted access possible and only allows

the unit to be identified by a host SNMP Station.

The

mib2

context allows a user with appropriate authentication to

access the mib2 OIDs and the SNMP OIDs. These are of interest

primarily to network operators not controlling the satellite link.

The

dev

context allows a user with appropriate authentication to

access the device control portion of the MIB. These OIDs are

used to control the devices satellite link and operation.

TRAP VERSION {V1, V2} This controls the type of message format used when a message

trap is generated by the equipment and bound for a SNMP Host.

Messages will only be sent if the unit has been authorized to do

so.

AUTHORIZATION {TRAPS OFF, TRAPS

ON}

This controls the type of message format used when a message

trap is generated by the equipment and bound for a SNMP host.

Messages will only be sent if the unit has been authorized to do

so.

RD COMMUNITY {16 characters of

name}

This menu is only displayed when SNMP VERSION is set to V1 &

V2. This is the community that a host must be acting within when

an OID variable is requested by a V1/V2 SNMP message.

RDWR COMMUNITY {16 characters of

name}

This menu is only displayed when SNMP VERSION is set to V1 &

V2. This is the community that a host must be acting within when

an OID variable is being changed by a V1/V2 SNMP message.

TRAP AGENT {XXX.XXX.XXX.XXX}

Hexadecimal Mask

{ddd.ddd.ddd.ddd}

Decimal Mask

IP address of the device receiving SNMP Traps

DMD2050E Universal Satellite Modem Theory of Operation

MN-DMD2050E Revision 2 3–

 Modem Status, Alarms & Contact Closures (Section 3.2.)

3.2.6 Terminal Port

This port supports an asynchronous control protocol as described in Chapter 4. It is configured to

support RS-232 signal levels. This port is intended for use in computer-based remote M&C. All

functions of the modem may be monitored and controlled from this port via a common terminal

connected to the Terminal Port. This function is front panel selectable.

The Terminal Mode Control allows the use of an external terminal or computer to monitor and

control the modem from a full screen interactive presentation operated by the modem itself. No

external software is required other than VT-100 Terminal Emulation Software (e.g. Procomm

for a computer when used as a terminal. The Control Port is normally used as an RS–232

Connection to the terminal device. The RS-232 operating parameters can be set using the

modem Front Panel and stored in Non-volatile memory for future use.

IMPORTANT

Refer to the Remote Protocol Manual (MN-DMDREMOTEOP) for the Terminal, Remote

and SNMP screens and protocols.

3.2. Modem Remote Communications (RP)

The Remote Port located on 20 allows for control and monitoring of parameters and functions

via an RS-232 Serial Interface, or RS-45 for RP Protocol. Equipment Remote Mode’ setup

can be entered from the front panel or the Web Browser interface under the System menu. This

requires the user to first set the Remote Port Control to Remote then set the Multidrop Address

as needed followed by setting the Remote Interface to RS232 or RS45.

Control and status messages are conveyed between the modem and all subsidiary modems and

the host computer using packetized message blocks in accordance with a proprietary

communications specification. This communication is handled by the Radyne ink evel Protocol

(RP), which serves as a protocol wrapper’ for the remote M&C data. See the MN-

DMDREMOTEOP manual for more information.

ER-DMD2050E-EB2 Rev - PLM C-0028804

Blank Page

ER-DMD2050E-EC2 Rev - PLM C-0035622

Errata C for MN-DMD2050E Rev 2

Comtech EF Data Documentation Update

Subject:

Preface, Electrical Safety section, page xx, change power consumption maximum

Errata Part

Number:

ER-DMD2050E-EC2 (Errata documents are not subject to revision.)

PLM CO

Number:

C-0035622

Comments:

The new information will be included in the next released revision of the manual.

ER-DMD2050E-EC2 Rev - PLM C-0035622

Blank Page

ER-DMD2050E-ED2 Rev - PLM C-0035823

Errata D for MN-DMD2050E Rev 2

Comtech EF Data Documentation Update

Subject:

EBEM mode set up on the DMD2050E, add 3.8.1 to Section 3.8

Errata Part Number:

ER-DMD2050E-ED2 (Errata documents are not subject to revision.)

PLM CO Number:

C-0035823

Comments:

The new information will be included in the next released revision of the manual.

See attached page.

ER-DMD2050E-ED2 Rev - PLM C-0035823

ER-DMD2050E-EE2 Rev -

Errata E for MN-DMD2050E Rev 2

Comtech EF Data Documentation Update

Subject:

Add Appendix K, Compatibility with other DMD Modems

Errata Part Number:

ER-DMD2050E-EE2 (Errata documents are not subject to revision.)

Comments:

The new information will be included in the next released revision of the manual.

ER-DMD2050E-EE2 Rev - 2

Blank Page

MN-DMD2050E Revision 2 K–1

ER-DMD2050E-EE2 Rev -

Appendix K. Compatibility with

Other DMD Modems

K.1 Compatibility with Other DMD Modems

MN-DMD2050E Revision 2 K–2

ER-DMD2050E-EE2 Rev -

Modulation

Code

Rate

Data Rate Range

(kbps)

DMD20 /

DMD20 LBST

HW1 + HW6

DMD1050 /

DMD1050T /

DMD1050TS

HW3 + HW8

OM20

HW1 + HW6

Data Rate Range

(kbps)

DMD50 /

DMD2050

HW2 + HW7

DMD2050E /

DMD2050EU

HW2 + HW7 + HW24

Legacy Modes

BPSK Viterbi 1/2 2.4 – 5,000 Standard Standard Standard 2.4 – 15,000 Standard Standard

QPSK

Viterbi

1/2 4.8 – 10,000 Standard Standard Standard 4.8 – 30,000 Standard Standard

3/4 7.2 – 15,000 Standard Standard Standard 7.2 – 45,000 Standard Standard

7/8 8.4 – 17,500 Standard Standard Standard 8.4 – 52,000 Standard Standard

Viterbi + RS

1/2 4.8 – 10,000 * R / N RS Feature RS Feature RS Feature 4.8 – 30,000 * R / N RS Feature Standard

3/4 7.2 – 15,000 * R / N RS Feature RS Feature RS Feature 7.2 – 45,000 * R / N RS Feature Standard

7/8 8.4 – 17,500 * R / N RS Feature RS Feature RS Feature 8.4 – 52,000 * R / N RS Feature Standard

Sequential

1/2 4.8 – 2,048 Sequential Feature Sequential Feature Sequential Feature 4.8 – 2,048 Sequential Feature Sequential Feature

3/4 7.2 – 2,048 Sequential Feature Sequential Feature Sequential Feature 7.2 – 2,048 Sequential Feature Sequential Feature

7/8 8.4 – 2,048 Sequential Feature Sequential Feature Sequential Feature 8.4 – 2,048 Sequential Feature Sequential Feature

OQPSK

Viterbi

1/2 4.8 – 10,000 Standard Standard Standard 4.8 – 30,000 Standard Standard

3/4 7.2 – 15,000 Standard Standard Standard 7.2 – 45,000 Standard Standard

7/8 8.4 – 17,500 Standard Standard Standard 8.4 – 52,000 Standard Standard

Viterbi + RS

1/2 4.8 – 10,000 * R / N RS Feature RS Feature RS Feature 4.8 – 10,000 * R / N RS Feature Standard

3/4 7.2 – 15,000 * R / N RS Feature RS Feature RS Feature 7.2 – 15,000 * R / N RS Feature Standard

7/8 8.4 – 17,500 * R / N RS Feature RS Feature RS Feature 8.4 – 17,500 * R / N RS Feature Standard

Sequential

1/2 4.8 – 2,048 Sequential Feature Sequential Feature Sequential Feature 4.8 – 2,048 Sequential Feature Sequential Feature

3/4 7.2 – 2,048 Sequential Feature Sequential Feature Sequential Feature 7.2 – 2,048 Sequential Feature Sequential Feature

7/8 8.4 – 2,048 Sequential Feature Sequential Feature Sequential Feature 8.4 – 2,048 Sequential Feature Sequential Feature

8PSK

Trellis 2/3 9.6 – 20,000 8PSK Feature 8PSK Feature 8PSK Feature 9.6 – 52,000 8PSK Feature Standard

Trellis + RS 2/3 9.6 – 20,000 * R / N 8PSK + RS Feature 8PSK + RS Feature 8PSK + RS Feature 9.6 – 52,000 8PSK + RS Feature Standard

16QAM Viterbi

3/4 14.4 – 20,000 16QAM Feature 16QAM Feature 16QAM Feature 14.4 – 52,000 16QAM Feature Standard

7/8 16.8 – 20,000 16QAM Feature 16QAM Feature 16QAM Feature 16.8 – 52,000 16QAM Feature Standard

MN-DMD2050E Revision 2 K–3

ER-DMD2050E-EE2 Rev -

Modulation

Code

Rate

Data Rate Range

(kbps)

DMD20 /

DMD20 LBST

HW1 + HW6

DMD1050 /

DMD1050T /

DMD1050TS

HW3 + HW8

OM20

HW1 + HW6

Data Rate Range

(kbps)

DMD50 /

DMD2050

HW2 + HW7

DMD2050E /

DMD2050EU

HW2 + HW7 + HW24

Viterbi + RS

3/4 14.4 – 20,000 * R / N 16QAM + RS Feature 16QAM + RS Feature 16QAM + RS Feature 14.4 – 52,000 16QAM + RS Feature Standard

7/8 16.8 – 20,000 * R / N 16QAM + RS Feature 16QAM + RS Feature 16QAM + RS Feature 16.8 – 52,000 16QAM + RS Feature Standard

DVB Modes

BPSK Viterbi

1/2 2.4 – 4,608 DVB Feature DVB Feature DVB Feature 2.4 – 4,608 DVB Feature DVB Feature

2/3 3.2 – 6,144 DVB Feature DVB Feature DVB Feature 3.2 – 6,144 DVB Feature DVB Feature

3/4 3.6 – 6,912 DVB Feature DVB Feature DVB Feature 3.6 – 6,912 DVB Feature DVB Feature

5/6 4.0 – 7,680 DVB Feature DVB Feature DVB Feature 4.0 – 7,680 DVB Feature DVB Feature

7/8 4.2 – 8,064 DVB Feature DVB Feature DVB Feature 4.2 – 8,064 DVB Feature DVB Feature

QPSK Viterbi

1/2 4.8 – 9,216 DVB Feature DVB Feature DVB Feature 4.8 – 9,216 DVB Feature DVB Feature

2/3 6.4 – 12,288 DVB Feature DVB Feature DVB Feature 6.4 – 12,288 DVB Feature DVB Feature

3/4 7.2 – 13,824 DVB Feature DVB Feature DVB Feature 7.2 – 13,824 DVB Feature DVB Feature

5/6 8.0 – 15,359 DVB Feature DVB Feature DVB Feature 8.0 – 15,359 DVB Feature DVB Feature

7/8 8.4 – 16,127 DVB Feature DVB Feature DVB Feature 8.4 – 16,127 DVB Feature DVB Feature

8PSK Trellis

2/3 9.6 – 18,431 8PSK + DVB Feature 8PSK + DVB Feature 8PSK + DVB Feature 9.6 – 18,431 8PSK + DVB Feature DVB Feature

5/6 12.0 – 20,000 8PSK + DVB Feature 8PSK + DVB Feature 8PSK + DVB Feature 12.0 – 20,000 8PSK + DVB Feature DVB Feature

8/9 12.8 – 20,000 8PSK + DVB Feature 8PSK + DVB Feature 8PSK + DVB Feature 12.8 – 20,000 8PSK + DVB Feature DVB Feature

16QAM Trellis

3/4 14.4 – 20,000 16QAM + DVB Feature 16QAM + DVB Feature 16QAM + DVB Feature 14.4 – 20,000 16QAM + DVB Feature DVB Feature

7/8 16.8 – 20,000 16QAM + DVB Feature 16QAM + DVB Feature 16QAM + DVB Feature 16.8 – 20,000 16QAM + DVB Feature DVB Feature

TPC Modes

BPSK

TPC

5/16 1.5 – 3,125 TPC Feature + HW16 TPC Feature + HW18 — 1.5 – 9,375 TPC Feature + HW16 Standard

21/44 2.3 – 4,773 TPC Feature + HW14 TPC Feature TPC Feature 2.3 – 14,318 TPC Feature + HW14 Standard

TPC (SHORT)

7/8-S 4.2 – 8,750 TPC Feature + HW15 — — 4.2 – 20,000 TPC Feature + HW15 —

QPSK TPC

21/44 4.6 – 9,545 TPC Feature + HW14 TPC Feature TPC Feature 4.6 – 20,000 TPC Feature + HW14 Standard

3/4 7.2 – 15,000 TPC Feature + HW14 TPC Feature TPC Feature 7.2 – 20,000 TPC Feature + HW14 Standard

MN-DMD2050E Revision 2 K–4

ER-DMD2050E-EE2 Rev -

Modulation

Code

Rate

Data Rate Range

(kbps)

DMD20 /

DMD20 LBST

HW1 + HW6

DMD1050 /

DMD1050T /

DMD1050TS

HW3 + HW8

OM20

HW1 + HW6

Data Rate Range

(kbps)

DMD50 /

DMD2050

HW2 + HW7

DMD2050E /

DMD2050EU

HW2 + HW7 + HW24

7/8 8.4 – 17,500 TPC Feature + HW14 TPC Feature TPC Feature 8.4 – 20,000 TPC Feature + HW14 Standard

0.495 64.0 – 6,132 TPC Feature + HW15 — — 64.0 – 6,132 TPC Feature + HW15 —

0.793 64.0 – 6,132 TPC Feature + HW15 — — 64.0 – 6,132 TPC Feature + HW15 —

TPC (SHORT)

7/8-S 64.0 – 17,500 TPC Feature + HW15 — — 64.0 – 20,000 TPC Feature + HW15 —

OQPSK

TPC

21/44 4.6 – 9,545 TPC Feature + HW-2 TPC Feature TPC Feature 4.6 – 20,000 TPC Feature + HW14 Standard

3/4 7.2 – 15,000 TPC Feature + HW-2 TPC Feature TPC Feature 7.2 – 20,000 TPC Feature + HW14 Standard

7/8 8.4 – 17,500 TPC Feature + HW-2 TPC Feature TPC Feature 8.4 – 20,000 TPC Feature + HW14 Standard

0.495 64.0 – 6,132 TPC Feature + HW15 — — 64.0 – 6,132 TPC Feature + HW15 —

0.793 64.0 – 6,132 TPC Feature + HW15 — — 64.0 – 6,132 TPC Feature + HW15 —

TPC (SHORT)

7/8-S 64.0 – 17,500 TPC Feature + HW15 — — 64.0 – 20,000 TPC Feature + HW15 —

8PSK TPC

3/4 10.8 – 20,000

8PSK + TPC Feature +

HW14

8PSK + TPC Feature 8PSK + TPC Feature 10.8 – 20,000

8PSK + TPC Feature +

HW14

Standard

7/8 12.6 – 20,000

8PSK + TPC Feature +

HW14

8PSK + TPC Feature 8PSK + TPC Feature 12.6 – 20,000

8PSK + TPC Feature +

HW14

Standard

0.495 64.0 – 6,132

8PSK + TPC Feature +

HW15

— — 64.0 – 6,132

8PSK + TPC Feature +

HW15

—

0.793 64.0 – 6,132

8PSK + TPC Feature +

HW15

— — 64.0 – 6,132

8PSK + TPC Feature +

HW15

—

0.750 — — — — 20,000.1 – 52,000

8PSK + TPC Feature +

HW15

—

0.875 — — — — 20,000.1 – 52,000

8PSK + TPC Feature +

HW15

—

8QAM TPC

3/4 10.8 – 20,000

8QAM + TPC Feature +

HW16

8QAM + TPC Feature +

HW18

— 10.8 – 20,000

8QAM + TPC Feature +

HW16

Standard

7/8 12.6 – 20,000 8QAM + TPC Feature + 8QAM + TPC Feature + — 12.6 – 20,000 8QAM + TPC Feature + Standard

MN-DMD2050E Revision 2 K–5

ER-DMD2050E-EE2 Rev -

Modulation

Code

Rate

Data Rate Range

(kbps)

DMD20 /

DMD20 LBST

HW1 + HW6

DMD1050 /

DMD1050T /

DMD1050TS

HW3 + HW8

OM20

HW1 + HW6

Data Rate Range

(kbps)

DMD50 /

DMD2050

HW2 + HW7

DMD2050E /

DMD2050EU

HW2 + HW7 + HW24

HW16 HW18 HW16

16QAM TPC

3/4 14.4 – 20,000

16QAM + TPC Feature

+ HW14

16QAM + TPC Feature 16QAM + TPC Feature 14.4 – 20,000

16QAM + TPC Feature +

HW14

Standard

7/8 16.8 – 20,000

16QAM + TPC Feature

+ HW14

16QAM + TPC Feature 16QAM + TPC Feature 16.8 – 20,000

16QAM + TPC Feature +

HW14

Standard

0.495 64.0 – 6,132

16QAM + TPC Feature

+ HW15

— — 64.0 – 6,132

16QAM + TPC Feature +

HW15

—

0.793 64.0 – 6,132

16QAM + TPC Feature

+ HW15

— — 64.0 – 6,132

16QAM + TPC Feature +

HW15

—

0.750 — — — — 20,000.1 – 52,000

16QAM + TPC Feature +

HW15

—

0.875 — — — — 20,000.1 – 52,000

16QAM + TPC Feature +

HW15

—

165B Turbo Modes

BPSK Turbo

1/2 64 – 5,000 — EBEM Feature + HW17 — 64 – 15,000 EBEM Feature + HW17 Standard

2/3 64 – 6,667 — EBEM Feature + HW17 — 64 – 20,000 EBEM Feature + HW17 Standard

3/4 64 – 7,500 — EBEM Feature + HW17 — 64 – 22,500 EBEM Feature + HW17 Standard

7/8 64 – 8,750 — EBEM Feature + HW17 — 64 – 26,250 EBEM Feature + HW17 Standard

19/20 64 – 9,500 — EBEM Feature + HW17 — 64 – 28,500 EBEM Feature + HW17 Standard

QPSK Turbo

1/2 64 – 10,000 — EBEM Feature + HW17 — 64 – 30,000 EBEM Feature + HW17 Standard

2/3 64 – 13,333 — EBEM Feature + HW17 — 64 – 40,000 EBEM Feature + HW17 Standard

3/4 64 – 15,000 — EBEM Feature + HW17 — 64 – 45,000 EBEM Feature + HW17 Standard

7/8 64 – 17,500 — EBEM Feature + HW17 — 64 – 52,500 EBEM Feature + HW17 Standard

19/20 64 – 19,000 — EBEM Feature + HW17 — 64 – 57,000 EBEM Feature + HW17 Standard

8PSK Turbo 1/2 256 – 15,000 — EBEM Feature + HW17 — 256 – 45,000 EBEM Feature + HW17 Standard

MN-DMD2050E Revision 2 K–6

ER-DMD2050E-EE2 Rev -

Modulation

Code

Rate

Data Rate Range

(kbps)

DMD20 /

DMD20 LBST

HW1 + HW6

DMD1050 /

DMD1050T /

DMD1050TS

HW3 + HW8

OM20

HW1 + HW6

Data Rate Range

(kbps)

DMD50 /

DMD2050

HW2 + HW7

DMD2050E /

DMD2050EU

HW2 + HW7 + HW24

2/3 256 – 20,000 — EBEM Feature + HW17 — 256 – 60,000 EBEM Feature + HW17 Standard

3/4 256 – 20,000 — EBEM Feature + HW17 — 256 – 67,500 EBEM Feature + HW17 Standard

7/8 256 – 20,000 — EBEM Feature + HW17 — 256 – 78,750 EBEM Feature + HW17 Standard

19/20 256 – 20,000 — EBEM Feature + HW17 — 256 – 85,500 EBEM Feature + HW17 Standard

16APSK Turbo

1/2 256 – 20,000 — EBEM Feature + HW17 — 256 – 60,000 EBEM Feature + HW17 Standard

2/3 256 – 20,000 — EBEM Feature + HW17 — 256 – 80,000 EBEM Feature + HW17 Standard

3/4 256 – 20,000 — EBEM Feature + HW17 — 256 – 90,000 EBEM Feature + HW17 Standard

7/8 256 – 20,000 — EBEM Feature + HW17 — 256 – 105,000 EBEM Feature + HW17 Standard

19/20 256 – 20,000 — EBEM Feature + HW17 — 256 – 114,000 EBEM Feature + HW17 Standard

LDPC Modes

BPSK

HP-LDPC 1/2 2.4 – 5,000 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 2.4 – 15,000 LDPC Feature + HW16 LDPC Feature

ULL-LDPC 1/2 2.4 – 4,933 LDPC Feature + HW19 — LDPC Feature + HW20 2.4 – 14,799 LDPC Feature + HW19 LDPC Feature

QPSK

HP-LDPC

1/2 4.8 – 10,000 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 4.8 – 20,000 LDPC Feature + HW16 LDPC Feature

2/3 6.4 – 13,333 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 6.4 – 20,000 LDPC Feature + HW16 LDPC Feature

3/4 7.2 – 15,000 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 7.2 – 20,000 LDPC Feature + HW16 LDPC Feature

ULL-LDPC

1/2 4.7 – 9,866 LDPC Feature + HW19 — LDPC Feature + HW20 4.7 – 20,000 LDPC Feature + HW19 LDPC Feature

2/3 6.3 – 13,078 LDPC Feature + HW19 — LDPC Feature + HW20 6.3 – 20,000 LDPC Feature + HW19 LDPC Feature

3/4 7.0 – 14,685 LDPC Feature + HW19 — LDPC Feature + HW20 7.0 – 20,000 LDPC Feature + HW19 LDPC Feature

OQPSK

HP-LDPC

1/2 4.8 – 10,000 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 4.8 – 20,000 LDPC Feature + HW16 LDPC Feature

2/3 6.4 – 13,333 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 6.4 – 20,000 LDPC Feature + HW16 LDPC Feature

3/4 7.2 – 15,000 LDPC Feature + HW16 LDPC Feature + HW18 LDPC Feature + HW20 7.2 – 20,000 LDPC Feature + HW16 LDPC Feature

ULL-LDPC

1/2 4.7 – 9,866 LDPC Feature + HW19 — LDPC Feature + HW20 4.7 – 20,000 LDPC Feature + HW19 LDPC Feature

2/3 6.3 – 13,078 LDPC Feature + HW19 — LDPC Feature + HW20 6.3 – 20,000 LDPC Feature + HW19 LDPC Feature

3/4 7.0 – 14,685 LDPC Feature + HW19 — LDPC Feature + HW20 7.0 – 20,000 LDPC Feature + HW19 LDPC Feature

Page is loading ...

Comtech EF Data DMD-2050E Operating instructions

Related papers

Other documents