Signature SOTERIA SLLSES Installation guide

Signature
Brand
Signature
Model
SOTERIA SLLSES
Type
Installation guide

Signature SOTERIA SLLSES is a 2.2w 3-in-1 emergency exit light that provides reliable illumination in the event of a power outage. Compliant with current IEE Wiring Regulations, this luminaire ensures your safety during emergencies.

Key Features:

  • Emergency Lighting: Provides backup illumination for up to 4 hours during power failures.

  • Automatic Operation: Switches to emergency mode automatically upon power loss.

  • Green Indicator: Indicates normal operation and battery charging status.

  • Easy Installation: Connects to standard mains supply wiring for hassle-free setup.

Signature SOTERIA SLLSES is a 2.2w 3-in-1 emergency exit light that provides reliable illumination in the event of a power outage. Compliant with current IEE Wiring Regulations, this luminaire ensures your safety during emergencies.

Key Features:

  • Emergency Lighting: Provides backup illumination for up to 4 hours during power failures.

  • Automatic Operation: Switches to emergency mode automatically upon power loss.

  • Green Indicator: Indicates normal operation and battery charging status.

  • Easy Installation: Connects to standard mains supply wiring for hassle-free setup.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Signature LED Lighting Unit 2, 34A Kershaw Street, Widnes WA8 7JA 0151 420 6000 www.signatureledlighting.co.uk
Installation Instructions
SOTERIA – SLLSES
2.2w 3 in 1 Emergency Exit
General installation instructions
These instructions should be read carefully before any installation and
retained after completion for further reference and maintenance. Please give
these instructions to the building owner/occupier after installation.
Important Safety
1. It is recommended that only a qualified electrical contractor carries out the
installation of this luminaire and that the luminaire is installed in compliance with
the current edition of the IEE Wiring Regulations.
2. Before commencing installation (and before maintenance at any time) ensure that
the mains supply and the battery pack to the luminaire are switched off and the
circuit supply fuses are removed or the circuit breaker is turned off.
3. Minimum distance around the apparatus should be ensured for sufficient
ventilation. The ventilation should NOT be impeded by being covered.
4. Where applicable careful consideration should be taken during installation to ensure
that all fittings or suspensions are of a suitable size for the luminaire being installed.
5. The person carrying out the installation is to check and verify that the total load on
the circuit, including that of the luminaire, does not exceed the rating of the circuit
cable, fuse or circuit breaker.
6. Where a luminaire incorporates discharge control gear (inductive load) the circuit
capacity and ratings require careful sizing to avoid nuisance tripping of the protective
device used in the installation.
7. Batteries are NI-Cd type and have a normal service life of approximately 4 years.
Batteries should any case, be replaced only with the type specified, and exclusively
be replaced by a qualified person.
8. Pay attention to the environment and ensure that on disposal of the batteries they
are properly treated and recycled, rather than being sent for incineration or to a
landfill.
Light Indicator working performance:
Normal fitting: Green indicator working.
Battery failure: Green indicator turned off.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Signature LED Lighting Unit 2, 34A Kershaw Street, Widnes WA8 7JA 0151 420 6000 www.signatureledlighting.co.uk
Installation
1. Connect main supply wiring as follows:
2. Brown cable usually connects live line;
Black cable connects switch live line;
Blue cable connects the neutral line;
Yellow cable connects the earth line.
3. Power line & battery wires should be connected strictly, and all screws fixed.
4. Switch on 220-240V AC supply and check if the green LED indicator illuminates to confirm
the charging of batteries.
5. Allow a short period for part charging of batteries and then isolate the main supply to the
fitting to check the correct operation of the fitting in emergency mode. In the first use, after
a continuous charge for 24 hours, a mains failure should be stimulated to ensure that the
fitting works for the specified time (only at a safe & appropriate time). The fitting will be
fully charged within 24 hours of continuous charging.
Warning
1. Disconnect the mains supply and unplug the battery leads before working on the unit.
2. Failure to comply with these instructions may result in irreparable damage to the emergency
control gear.
3. This product must not be modified in any way as this will negate any safety approvals, and
may render the product inoperable or unsafe
ROUTINE TEST RECORD
FIRST YEAR
SECOND YEAR
THIRD YEAR
FOURTH YEAR
FIFTH YEAR
MONTH
TEST
DATE
SIGNED
DATE
SIGNED
DATE
SIGNED
DATE
DATE
1
FUNCTION
2
FUNCTION
3
FUNCTION
4
FUNCTION
5
FUNCTION
6
FUNCTION
7
FUNCTION
8
FUNCTION
9
FUNCTION
10
FUNCTION
11
FUNCTION
12
FUNCTION
Eventually, you may want to replace this fitting:
When your fitting and battery pack come to the end of their life or you chose to update or upgrade the fitting by replacing it, please do not dispose
of it in your normal household waste, please recycle where facilities exist. When you need to dispose of the fitting, check with your retailer or local
authority for suitable options. New regulations will encourage the recycling of Waste from Electrical and Electronic Equipment (European “WEEE
Directive” effective August 2005)
  • Page 1 1
  • Page 2 2

Signature SOTERIA SLLSES Installation guide

Signature
Brand
Signature
Model
SOTERIA SLLSES
Type
Installation guide

Signature SOTERIA SLLSES is a 2.2w 3-in-1 emergency exit light that provides reliable illumination in the event of a power outage. Compliant with current IEE Wiring Regulations, this luminaire ensures your safety during emergencies.

Key Features:

  • Emergency Lighting: Provides backup illumination for up to 4 hours during power failures.

  • Automatic Operation: Switches to emergency mode automatically upon power loss.

  • Green Indicator: Indicates normal operation and battery charging status.

  • Easy Installation: Connects to standard mains supply wiring for hassle-free setup.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents