PRODUCT MANUAL
BAT/44892
www.aqtron.com - [email protected]
®
SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions. Read
through this owner’s manual carefully before using your new tool. Pay close attention to all safety instruc-
tions, Warning and Caution sections. Use your tool properly and only for its intended use.
WARNING:
1. The appliance is not intended for use by young children or inrm persons without supervision.
2. Young children should be supervised to ensure that they do not play with the appliance.
3. The jump starters described in this manual are suitable for portable power source or off-road side
battery emergency rescues. Ratings are described as below.
BAT/44892 : 12/24V, 1700/3400A
Caution :
1. Contains sealed, non-spillable lead acid battery. Must be disposed of properly.
2. Unit should be kept at full charge.
3. Recharge upon purchase and immediately after each use.
4. Recharge if not used for six months.
5. Can be charged continuously without damage to unit.
WARNING : Risk of Explosive Gases
1. A lead acid battery is dangerous because it can generate explosive gases during normal battery
operation.
2. To reduce risk of explosion, follow these instructions and those of the battery manufacturer and of any
equipment you intend to use in vicinity of battery. Review warnings on these products and on battery.
3. Make sure someone is close enough to come to your aid when you are working with a lead-acid battery.
4. Avoid touching eyes while working with a lead- acid battery. Wear complete eye and clothing protection.
5. Keep fresh water and soap nearby in case battery acid contacts skin. Wash immediately with soap and
water if battery acid contacts skin or clothing. If acid should get into your eye, ush immediately with
cold water for 10 minutes, and get medical attention.
6. Never smoke while working with a lead-acid battery. Do not allow a spark or ame to get near battery.
7. Be careful to not drop any metal tool or object onto battery as sparking may occur. This may create an
explosion hazard.
8. A lead-acid battery can produce a short-circuit current strong enough to weld metal to skin. Remove all
jewelry and personal metal items when working with a lead-acid battery.
9. Do not use the portable power source to charge dry-cell batteries. These batteries may burst and cause
injury and damage to persons or property.
10. Do not attempt to charge or boost a frozen lead-acid battery.
PRODUCT MANUAL
BAT/44892
www.aqtron.com - [email protected]
®
11. Even though the portable power source is equipped with polarity warning, prevent clamps from
touching each other or contact the same metal to prevent accidental arcing.
12. Use of an attachment not recommended or sold by the manufacturer, may result in a risk of damage to
the unit, or personal injury.
13. When using the wall charger or power extension cord, pull on the plug and NEVER ON THE CORD when
disconnecting.
14. Replace damaged wall charger or power extension cord immediately. Do not attempt to recharge the
portable power source with damaged cords.
15. The portable power source is designed for use under any weather condition.
16. Prevent submersion in water.
17. Do not operate with ammables in the vicinity such as gasoline etc.
18. If the portable power source is damaged in any way, discontinue use. If the portable power source is
leaking battery acid do not scrap it. Take it to the closest battery recycler in your area.
19. The portable power source should never be left in a total discharged state for any period of time.
Damage to the battery could be permanent When not in use, leave the portable power source connect
ed to the wall charger or recharge every six(6) months.
OPERATIONAL AND SAFETY DESIGN FEATURES.
1. The portable power source provides more than enough starting power for most vehicles. May also be
used in deep cycle applications.
2. The portable power source will power most 12 Vdc equipment with a male cigarette dc plug.
3. The portable power source comes equipped with dc automatic overload protection.
4. The portable power source contains a 12 volt sealed battery. It is recommended to be stored in up posi-
tion.
5. The portable power source contains reverse polarity warning which will remind of incorrect setting be
fore power ON.
6. Safety storage compartment provide convenient storage of cables when not in use.
Important Note
Unauthorized modications to the portable power source, not expressly approved by the party responsible
for radio, frequency emission levels from the portable power source, may cause an increased amount of radio
frequency energy to be emitted. Such a modication could void the customer’s authority to use the portable
power source.
SAFETY FEATURES
1. Safety storage compartments prevent accidental sparking of clamps.
2. The portable power source contains the latest technology with its 12 volt sealed non-spillable battery.
The portable power source may be stored in any position.
3. The portable power source is recommended to be stored in up position.
FIRST TIME CHARGING PROCEDURES
When rst purchased the portable power source should be charged for a minimum of 30 hours, unless all the
power level lights and the charged light come on when the test button is pressed.
The power source can only be charged at 12V.
19. The portable power source should never be left in a total discharged state for any period of time. Damage
to the battery could be permanent When not in use, leave the portable power source connected to the
wall charger or recharge every six(6) months.
OPERATIONAL AND SAFETY DESIGN FEATURES.
1. The portable power source provides more than enough starting power for most vehicles. May also be used in
deep cycle applications.
2. The portable power source will power most 12 Vdc equipment with a male cigarette dc plug.
3. The portable power source comes equipped with dc automatic overload protection.
4. The portable power source contains a 12 volt sealed battery. It is recommended to be stored in up position.
5. The portable power source contains reverse polarity warning which will remind of incorrect setting before power
ON.
6. Safety storage compartment provide convenient storage of cables when not in use.
Important Note
Unauthorized modifications to the portable power source, not expressly approved by the party responsible for radio
frequency emission levels from the portable power source, may cause an increased amount of radio frequency
energy to be emitted. Such a modification could void the customer’s authority to use the portable power source.
SAFETY FEATURES
1. Safety storage compartments prevent accidental sparking of clamps.
2. The portable power source contains the latest technology with its 12 volt sealed non-spillable battery. The
portable power source may be stored in any position.
3. The portable power source is recommended to be stored in up position.
FIRST TIME CHARGING PROCEDURES
When first purchased the portable power source should be charged for a minimum of 30 hours, unless all the power
level lights and the charged light come on when the test button is pressed.
The power source can only be charged at 12V.
Figure 1. Test Button, Charging and Charged LED’S
RECHARGING THE PORTABLE POWER SOURCE
There are two ways to charge the portable power source. The first method is automatic charging with the provided
switching charger (preferred). The second is with the DC power jack through the power extension cord. The second
way is not automatic and requires monitoring or the portable power source could be damaged due to overcharging.
1. With the switching charger. The portable power source is charged by switching charger with cigarette lighter jack,
(may be found on the front of your portable power source). Recharging takes approximately 4 to 6 hours for each
light that does not come on when the test button is pressed. The portable power source CAN be left connected to
the switching charger indefinitely.
a. Connect the charger to the AC outlet.
b. Insert the charger male cigarette jack into the charging jack.
c. Turn the safety switch to “ON” or “12V” position.
d. Allow the portable power source to charge until the charged light comes on.
e. Once the charged light comes on, you can either disconnect the charger or charge another three to six
hours, (three hours is acceptable but to ensure maximum output capability, six hours is preferred).
Note: Above charging hour is for reference. Charge condition will change per charger design.
2. With the Optional DC/DC Extension Cord.
a. Start the vehicle engine.
b. Plug one end of the power extension cord into the portable power source dc receptacle and the other end
into a vehicle lighter outlet and turn power switch to “ON” or “12V” position.
c. Press the test button to check volt meter. If meter indicates above 13V when power switch is in “ON” or
“12V” position, disconnect DC plug and turn off the power switch on your booster.
Modle:HS120S
Modle:HS340S/HO324S
PRODUCT MANUAL
BAT/44892
www.aqtron.com - [email protected]
®
RECHARGING THE PORTABLE POWER SOURCE
There are two ways to charge the portable power source. The rst method is automatic charging with the
provided switching charger (preferred). The second is with the DC power jack through the power extension
cord. The second way is not automatic and requires monitoring or the portable power source could be dam-
aged due to overcharging.
1. With the switching charger. The portable power source is charged by switching charger with cigarette
lighter jack, (may be found on the front of your portable power source). Recharging takes approximately 4 to
6 hours for each light that does not come on when the test button is pressed. The portable power source CAN
be left connected to the switching charger indenitely.
a. Connect the charger to the AC outlet.
b. Insert the charger male cigarette jack into the charging jack.
c. Turn the safety switch to “ON” or “12V” position.
d. Allow the portable power source to charge until the charged light comes on.
e. Once the charged light comes on, you can either disconnect the charger or charge another
three to six hours, (three hours is acceptable but to ensure maximum output capability, six
hours is preferred).
Note: Above charging hour is for reference. Charge condition will change per charger design.
2. With the Optional DC/DC Extension Cord.
a. Start the vehicle engine.
b. Plug one end of the power extension cord into the portable power source dc receptacle and
the other end into a vehicle lighter outlet and turn power switch to “ON” or “12V” position.
c. Press the test button to check volt meter. If meter indicates above 13V when power switch is
in ON” or “12V” position, disconnect DC plug and turn off the power switch on your booster.
DO NOT OVERCHARGE! This is not an automatic method of charging the portable power source. You must
frequently monitor the charging process (by pressing the test button to check the power levels) to ensure the
portable power source is not overcharged. Overcharging will damage the portable power source.
Note: Test button needs to be pressed to check power level at volt meter.
Note: DO NOT OVERCHARGE! This is NOT an automatic method of charging the portable power source. Be
sure to frequently monitor the charging status to ensure the portable power source is not overcharged. Over-
charging will damage the portable power source.
OPERATING INSTRUCTIONS USE AS A BATTERY CHARGER
The portable power source can be used to restore a limited charge to the vehicle battery.
1. Using the dc extension cord included with the portable power source, plug one end into the portable
power source. Plug the other end into the vehicle cigarette outlet. Allow the battery to charge for 30
minutes.
2. Some vehicle ignitions must be turned to “accessory” to activate the cigar lighter socket. A defective
battery may not accept a charge from the portable power source.
3. Remove the power extension cord and start the vehicle.
PRODUCT MANUAL
BAT/44892
www.aqtron.com - [email protected]
®
USE AS A JUMP STARTER IN EMERGENCIES
For optimum performance, do not store below 50 F when using as a jump starter. The portable power source
will only jump start a battery if there is more than 3 Vdc of power remaining in the battery. If the battery is
below 3 Vdc, please refer to, “Operating Instructions: Use as a battery charger”, and follow the instructions to
recharge the battery.
1. Ignition MUST be turned off before making cable connections.
2. Be sure you operate the portable power source in a well ventilated area.
3. Be sure eyes are appropriately protected with safety eyewear.
4. Attach the red (positive +) clamp to the positive terminal on the battery.
5. Attach the black (negative -) clamp to the vehicle frame.
6. Be sure that all cables are clear of moving belts or fan blades.
7. Keep a safe distance from battery while jump starting.
8. Turn on the vehicle ignition. If the vehicle does not start after 6 seconds, let the portable power source
cool for 3 minutes before attempting to start the vehicle again. Damage could result to the unit if this is
not done.
9. After the vehicle has started, disconnect the black (negative -) clamp to the vehicle frame. Then remove
the red (positive +) from the battery terminal. The yellow Charging light will remain lit until the red
(positive +) cable is disconnected from the battery. After use, store the clamps in the compartments.
USE AS AN ALTERNATIVE POWER SUPPLY
Since most vehicles have electronic components (alarm systems, radios, etc.) whose memory can be lost
when the battery is disconnected, the portable power source is a useful tool when replacing a battery. By
connecting the DC extension cord to the vehicle’s cigarette lighter, the memory can be retained.
USE AS A MULTI-PURPOSE POWER SOURCE
1. The portable power source can also be used to power any equipment that incorporates a 12 Vdc male
adapter. The dc outlet on the portable power source comes equipped with overload protection. DC
power will be generated only through the dc outlet.
2. Used with an inverter, the portable power source can operate appliances normally powered by 120 Vac
or 220 Vac. A 300 Watt maximum inverter is recommended.
TROUBLESHOOTING
1. Charger works well but there is no Volt change on volt meter when the wall charger is connected to the
portable power source.
a. Possible defective battery or faulty breaker. Try using a device (light, TV etc.) with a dc plug on it to
see if it works. .
b. If it works, the portable power source breaker is operational and the battery may be the issue.
2. Charger comes up full charge but test button pressed, volt meter shows low voltage.
a. Portable power source has a defective battery. May be caused by intense use without allowing a
cool down period.
b. Use a dc plug to connect other battery or device to see if volt meter analog indicator moves. If not,
replace volt meter.
3. Portable power source is fully charged but has no power.
a. Check where the wire meets the jaw on the portable power source clamp. Make sure they are well
crimped, or if your unit has a power switch, make sure it is in the on position.
4. When trying to use an accessory through the dc outlet, a clicking Sound comes from inside the portable
power source.
a. The accessory is drawing too many amps, causing the internal circuit breaker to cycle ON and OFF.
PRODUCT MANUAL
BAT/44892
www.aqtron.com - [email protected]
®
FREQUENTLY ASKED QUESTIONS
Q: How many jump starts can I expect from a fully charged unit before needing to be recharged?
A: Depending on the engine type and size, condition of battery, and temperature the portable power source
normally can be used 20 times before recharging.
Q: What is the ideal storage temperature of the portable power source?
A: The portable power source will operate most effectively when stored at room temperature. The unit will
also operate under below zero degree conditions, but with less cranking power. Excessive heat will accelerate
self discharge.
Q: When recharging the unit, where should I know power source is fully charged?
A: Press test button to check voltage from volt meter. If the analog indicator over 14V, battery is fully charged.
Q: How long should I charge the portable power source?
A: The portable power source should be charged for a minimum of 30 hours when rst purchased. To re-
charge with the A/C adapter, the unit should charge 4 to 6 hours for every light not lit when the test button is
pushed. The unit can be left on the wall charger continuously without damaging the unit.
Q: Can the self contained battery be recycled?
A: Yes. Please see REMOVAL AND DISPOSAL instructions.
TESTING THE BATTERY OF PORTABLE POWER SOURCE
After fully charging the battery so all red lights come on, use a 100 amp batter load tester to apply a 100 amp
load to the portable power source. For a period of 6 seconds, the voltmeter on load tester should be 9 Vdc or
higher.
BATTERY REMOVAL AND DISPOSAL INSTRUCTIONS
Contains sealed, non-spillable lead acid battery. Must be disposed of properly.
IMPORTANT :
REMOVAL AND DISPOSAL
The battery inside this portable power source is a sealed lead-acid battery. It is required by law to be removed
and recycled or disposal of properly. National, as well as, any additional local regulations must be followed.
When the battery in this product is in need of disposal, remove it according to the instructions provided
below and take it to your local recycling center for proper recycling or disposal. If you don’t have a local recy-
cling center that handles sealed lead-acid batteries, contact your local environmental agency for instructions.
REMOVAL INSTRUCTIONS
Begin by making sure that both booster clamps are securely stored in their compartments on each side of the
portable power source.
1. Lay the portable power source front side down. On the back of the unit, locate the screws that hold the
portable power source enclosure together.
2. Remove the screws, then lift off the back lid of the portable power source enclosure.
3. On the top of the battery are two terminals, each with wires connected to them. Disconnect these wires
from the battery by removing the bolts that hold them to the battery terminals. Be careful not to touch
both the battery terminals with the tools being used to remove the bolts to prevent accidental arcing.
4. Lift the battery out of the front of the enclosure.
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Rac RAC-HP082 User manual
-
Mercury CB-R3 User manual
-
Mercury SMDC406UK User manual
-
Clore Automotive JNC660 Product information
-
DSR Pro Series Professional Battery Boosters Owner's manual
-
DSR DSR5221 Owner's manual
-
Schumacher DSR103 Booster DSR103AUX Booster Owner's manual
-
Northern Industrial POWER BOOSTER Owner's manual
-
Jump-N-Carry JUMP n Carry JNC1224 12-24 Volt Power Supply and Jump Starter User manual
-
