Porter Cable PXMS12ISB Operating instructions

1

12 IN. (305 MM)

COMPOUND MITER SAW

SIERRA INGLETEADORA COMPUESTA

DE 305MM (12 PULG.)

Instruction Manual

Manual de instrucciones

Español: Página 32

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE

SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

PXMS12ISB

TABLE OF CONTENTS

PRODUCT SPECIFICATIONS

SECTION

PRODUCT SPECIFICATIONS.....................................................................................................................

CALIFORNIA PROPOSITION 65.................................................................................................................

SAFETY GUIDELINES - DEFINITIONS ......................................................................................................

POWER TOOL SAFETY..............................................................................................................................

MITER SAW SAFETY..................................................................................................................................

ELECTRICAL REQUIREMENTS AND SAFETY..........................................................................................

TOOLS NEEDED FOR ASSEMBLY............................................................................................................

CARTON CONTENTS.................................................................................................................................

KNOW YOUR COMPOUND MITER SAW...................................................................................................

GLOSSARY OF TERMS..............................................................................................................................

ASSEMBLY AND ADJUSTMENTS..............................................................................................................

OPERATION................................................................................................................................................

MAINTENANCE...........................................................................................................................................

TROUBLESHOOTING GUIDE.....................................................................................................................

ACCESSORIES AND ATTACHMENTS.......................................................................................................

REPLACEMENT PARTS LIST.....................................................................................................................

WARRANTY.................................................................................................................................................

PAGE

2

3

4

6

8

10

11

12

14

21

27

28

29

30

31

Motor ......................

Speed (no load).......

Double Insulated.....

Saw Blade ..............

Arbor Size...............

Dust Port Size.........

Bevel Range............

Miter Range.............

Weight.....................

120 V AC, 60 Hz, 15 A

3800 RPM

Yes

12 in (305 mm) 40T

Carbide-tipped

1 in. (25.4 mm)

1 1/4 in. (31.75 mm)

-3° - 48°

0° - 48° R & L

35.2 lbs (16 kg)

CUTTING CAPACITY (Dimensional lumber)

Cross Cut 0° x 0° .....................

Miter Cut 45° x 0°......................

Bevel Cut 0° x 45°.....................

Compound Cut 45° x 45°..........

MITER/BEVEL POSITIVE STOP ANGLES

Miter Detent Stops ...................

Bevel Positive Stops.................

4 x 6 in., 2 x 8 in.

(101.6 x 152.4 mm, 50.8 x 203.2 mm)

4 x 4 in. (101.6 x 101.6 mm)

2 x 6 in. (50.8 x 152.4 mm)

2 x 4 in. (50.8 x 101.6 mm)

0°, 15°, 22.5°, 31.6°, 45° , 48° R & L

-3°, 0°, 45°, 48°

WARNING

electrical circuit for your tools.

way.

2017/07

Printed in China

2

CALIFORNIA PROPOSITION 65

SAFETY GUIDELINES - DEFINITIONS

WARNING

WARNING ICONS

SAFETY ALERT: Precautions that involve your safety.

PROHIBITION DOUBLE INSULATED CONSTRUCTION

WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields.

WEAR RESPIRATORY AND HEARING PROTECTION: Always wear respiratory and hearing protection.

READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce the risk of injury, user and all bystanders

must read and understand instruction manual before using this product.

CAUTION

WARNING

DANGER

CAUTION

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which,

if not avoided, may result in property damage.

KEEP HANDS AWAY FROM THE MOVING PART AND CUTTING SURFACE: Failure to keep your hands

away from the moving part and cutting surface will result in serious personal injury.

SUPPORT AND CLAMP WORK

3

12. ALWAYS WEAR EYE PROTECTION. Any

power tool can throw foreign objects into the

eyes and could cause permanent eye damage.

ALWAYS wear Safety Goggles (not glasses)

that comply with ANSI Safety standard Z87.1.

Everyday eyeglasses have only impact–resistant

lenses. They ARE NOT safety glasses. NOTE: Glasses

or goggles not in compliance with ANSI Z87.1 could

seriously injure you when they break.

13. WEAR A FACE MASK OR DUST MASK.

Sawing operation produces dust.

14. SECURE WORK. Use clamps or a vise to

hold work when practical. It is safer than

using your hand and it frees both hands

to operate the tool.

15. DISCONNECT TOOLS FROM POWER SOUCE

before servicing, and when changing accessories

such as blades, bits and cutters.

16. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in the OFF position

before plugging the tool in.

17. USE RECOMMENDED ACCESSORIES. Consult this

Instruction Manual for recommended accessories.

The use of improper accessories may cause risk of

injury to yourself or others.

18. NEVER STAND ON THE TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

19. CHECK FOR DAMAGED PARTS. Before further

use of the tool, a guard or other part that is damaged

should be carefully checked to determine that it will

operate properly and perform its intended function

– check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting and any

other conditions that may affect its operation. A guard

or other part that is damaged should be properly

repaired or replaced.

20. NEVER LEAVE THE TOOL RUNNING UNATTENDED.

. Do not walk away from

a running tool until the blade comes to a complete

stop and the tool is unplugged from the power source.

21. DO NOT OVERREACH. Keep proper footing and

balance at all times.

22. MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

23. DO NOT use power tool in presence of flammable

liquids or gases.

POWER TOOL SAFETY

GENERAL SAFETY INSTRUCTIONS

BEFORE USING THIS POWER TOOL

Safety is a combination of common sense, staying alert

and knowing how to use your power tool.

To avoid mistakes that could cause serious

Failure to follow all instructions listed below may

1. READ and become familiar with the entire

Instruction Manual. LEARN the tool’s

application, limitations and possible hazards.

2. KEEP GUARDS IN PLACE and in working order.

3. REMOVE ADJUSTING KEYS AND WRENCHES.

Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool before

turning ON.

4. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

5. DO NOT USE IN DANGEROUS ENVIRONMENTS

Do not use power tools in damp locations, or expose

them to rain or snow. Keep work area well lit.

6. KEEP CHILDREN AWAY. All visitors and bystanders

should be kept a safe distance from work area.

7. MAKE WORKSHOP CHILD PROOF with padlocks,

master switches or by removing starter keys.

8. DO NOT FORCE THE TOOL. It will do the job better

and safer at the rate for which it was designed.

9. USE THE RIGHT TOOL. Do not force the tool or an

attachment to do a job for which it was not designed.

10. USE PROPER EXTENSION CORDS. Make sure

your extension cord is in good condition. When using

an extension cord, be sure to use one heavy enough

to carry the current your product will draw. An

undersized cord will result in a drop in line voltage

and in loss of power which will cause the tool to

overheat. The table on page 9 shows the correct size

to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier

gauge. The smaller the gauge number, the heavier

the cord.

11. WEAR PROPER APPAREL. Do not wear loose

clothing, gloves, neckties, rings, bracelets or other

jewelry which may get caught in moving parts.

Nonslip footwear is recommended. Wear protective

hair covering to contain long hair.

WARNING

4

26. WEAR HEARING PROTECTION. to reduce

the risk of induced hearing loss.

POWER TOOL SAFETY

24. DO NOT operate the tool if you are under the

influence of any drugs, alcohol or medicationn that

could affect your ability to use the tool properly.

25. Dust generated from certain materials can be

hazardous to your health. Always operate saw in

well-ventilated area and provide for proper dust

removal.

5

18. MAKE SURE the blade is not contacting the workpiece

before the switch in turned ON.

19. IMPORTANT: After completing the cut, release the

trigger and wait for the blade to stop before returning

the saw to the raised position.

20. MAKE SURE the blade has come to a complete stop

before removing or securing the workpiece. Changing

the workpiece angle or changing the angle of the

blade.

21. NEVER cut metals or masonry products with this tool.

This miter saw is designed for use on wood and

wood-like products.

22. NEVER cut small pieces. If the workpiece being cut

would cause your hand or fingers to be within 9-1/2

in. (240 mm) of the saw blade, the workpiece is too

small.

23. PROVIDE adequate support to the sides of the saw

table for long workpieces.

24. NEVER use the miter saw in an area with flammable

liquids or gases.

25. NEVER use solvents to clean plastic parts. Solvents

could possibly dissolve or otherwise damage the

material.

26. SHUT OFF the power before servicing or adjusting

the tool.

27. DISCONNECT the saw from the power source and

clean the machine when finished using.

28. MAKE SURE the work area is clean before leaving

the machine.

29. SHOULD any part of your miter saw be missing,

damaged, or fail in any way, or any electrical

component fail to perform properly, lock the switch

and remove the plug from the power supply outlet.

Replace missing, damaged, or failed parts before

resuming operation.

30. Because of the downward cutting motion, your safety

requires that you stay very alert to keep hands and

fingers away from the path that the blade travels.

31. Be sure all guards are in places and working. If

a guard seems slow to return to its normal position or

“hangs-up”, adjust or repair it immediately. Be alert at

all times - especially during repetitive, monotonous

operations. Don’t be lulled into carelessness due to a

false sense of security. Blades are extremely unforgiving.

Clean the lower guard frequently to help visibility and

movement. Unplug before adjustment or cleaning.

32. Abrasive cut-off wheels should not be used on miter

saw. Miter saw guards are not appropriate for abrasive

cut-off wheels.

MITER SAW SAFETY

SPECIFIC SAFETY INSTRUCTIONS FOR THIS

COMPOUND MITER SAW

1. DO NOT USE THIN KERF BLADES they can deflect

and contact guard an can cause possible injury to the

operator.

2. DO NOT operate the miter saw until it is completely

assembled and installed according to these

instructions.

3. IF YOU ARE NOT thoroughly familiar with the

operation of miter saws, seek guidance from your

supervisor, instructor or other qualified person.

4. ALWAYS hold the work firmly against the fence and

table. DO NOT perform any operation free hand (use

clamp wherever possible).

5. KEEP HANDS out of the path of the saw blade. If the

workpiece you are cutting would cause your hands to

be with 9-1/2 in. (240 mm) of the saw blade, the

workpiece should be clamped in place before making

the cut.

6. BE SURE the blade is sharp, runs freely and is free

of vibration.

7. ALLOW the motor to come up to full speed before

starting a cut.

8. KEEP THE MOTOR AIR SLOTS CLEAN and free of

chips or dust.

9. ALWAYS MAKE SURE all handles are tight before

cutting, even if the table is positioned in one of the

positive stops.

10. BE SURE both the blade and the flanges are clean

and the arbor bolt is tighten securely.

11. USE only blade flanges specified for your saw.

12. NEVER use blades larger in diameter than 12 in.

(305 mm).

13. NEVER apply lubricants to the blade when it is

running.

14. ALWAYS check the blade for cracks or damage

before operation. Replace a cracked or damged

blade immediately.

15. NEVER use blades recommended for operation at

less than 3800 RPM.

16. ALWAYS keep the blade guards in place and use at

all times.

17. NEVER reach around the saw blade.

6

39. WARNING: For your own safety, read instruction

manual before operating miter saw. Failure to obey

warnings in saw manual can result in serious injury.

Wear eye protection. Never operate saw without

proper, functional blade guard.

Never use if damage (i.e. breakage, cracks, loose

tips) is suspected.

Use a blade that can support the saw's maximum

speed.

Turn off tool and wait for saw blade to stop before

moving workpiece or changing settings.

Unplug tool before changing blade or servicing tasks.

MITER SAW SAFETY

33. To avoid loss of control or placing hands in the path

of the blade, hold or clamp all material securely against

the fence when cutting. Do not perform operations

freehand.

34. Support long material at the same height as the saw

table.

35. After completing a cut, release the trigger switch and

allow the blade to come to a complete stop, then raise

the saw blade from the workpiece.

36. Lock the miter saw head in the down position during

transport or when not in use.

37. DRY RUN - It is important to know where the blade

will intersect with workpiece during cutting operation.

Always perform a simulated cutting sequence with the

power toll switch OFF to gain an understanding of the

projected path of the saw blade. At some extreme

angles, the right or left side fence might have to be

removed to ensure proper clearance prior to making

a cut.

38. Double insulation - When servicing, use only identical

replacement parts.

7

WARNING

1. Connect this saw to a 120 V circuit. This circuit must

not be less than a #12 wire with a 20 A time lag fuse

or a #14 wire with a 15 A time lag fuse. NOTE: When

using an extension cord on a circuit with a # 14 wire,

the extension cord must not exceed 25 feet in length.

2. If the motor will not start, release the trigger switch

immediately. UNPLUG THE SAW. Check the saw

blade to make sure it turns freely. If the blade is free,

try to start the saw again. If the motor still does not

start, refer to the TROUBLESHOOTING GUIDE.

3. If the tool suddenly stalls while cutting wood, release

the trigger switch, unplug the tool and free the blade

from the wood. The saw may now be started and the

cut finished.

4. FUSES may “bolw” or circuit breakers may trip

frequently if:

a: MOTOR is overload - overloading can occur if you

feed too rapidly or make too many start/stops in a

short time.

b: LINE VOLTAGE is more than 10% above or below

the nameplate voltage rating. For heavy loads, the

voltage at motor terminals must equal the voltage

specified on the nameplate.

c. IMPROPER or dull saw blades are used.

5. Most motor trouble may be traced to loose or incorrect

connections, overload, low voltage or inadequate

power supply wiring. Always check the connections,

the load and supply circuit if the motor doesn’t run

well. Check minimum gauge for the length of cord you

are using on the chart below.

GUIDELINES FOR EXTENSION CORDS

Use a proper extension cord. Make sure your extension

cord is good condition. When using an extension cord,

be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a

drop in line voltage, resulting in loss of power and

overheating. The table (on page 9) shows the correct size

to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The smaller

the gauge number, the heavier the cord.

and in

good condition. Always replace a damaged extension cord

or have it repaired by a qualified person before using it.

Protect your extension cords from sharp objects, excessive

heat and damp or wet areas.

This

circuit must not be less than a #12 wire with a 20 A time

lag fuse or a #14 wire with a 15 A time lag fuse. NOTE:

When using an extension cord on a circuit with a #14

wire, the extension cord must not exceed 25 feet in length.

Before connecting the tool to the power line, make sure

the switch is in the OFF position and the electric current

is rated the same as the current stamped on the motor

nameplate, running at a lower voltage will damage the

motor.

ELECTRICAL REQUIREMENTS AND SAFETY

POWER SUPPLY AND MOTOR SPECIFICATIONS

The AC motor used in this saw is a universal, nonreversible

type. See “PRODUCT SPECIFICATIONS” section on

page 2.

to a 120 V, 15 A circuit and use a 15 A time delay fuse

ELECTRICAL REQUIREMENTS

DOUBLE INSULATED

The power tool is double insulated to provide a double

thickness or insulation between you and tool’s electrical

system. All exposed metal parts are isolated from the

internal metal motor components with protecting insulation.

When servicing, use only identical

replacement parts.

This saw has a plug that looks like the

one shown below:

WARNING

To avoid electrocution:

1. Use only identical replacement parts when servicing

a tool with double insulation. Servicing should be

performed by a qualified technician.

2. Do not use power tools in wet or damp locations or

expose them to rain or snow.

MOTOR SAFETY PROTECTION

IMPORTANT

To avoid motor damage, the motor should be blown out

or vacuumed frequently to keep sawdust from interfering

with the motor ventilation.

To reduce the risk of electrical shock, this saw has

a arized plug (one blade is wider than the other).

This plug will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet, reverse the plug.

If it is still does not fit, contact a qualified electrician to

install the proper outlet. Do not change the plug in any

way.

8

ELECTRICAL REQUIREMENTS AND SAFETY

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

(When using 120 volts only)

More Than

0

6

10

12

Not More Than

6

10

12

16

25ft.

18

16

14

50ft.

16

12

100ft.

16

14

150ft.

14

12

Not Recommended

9

WARNING

If any part is missing or damaged, do not attempt to

assemble the miter saw, or plug in the power cord until

the missing or damaged part is correctly replaced.

The use of attachments or accessories not listed

in this manual might be hazardous and could cause

serious personal injury.

TABLE OF LOOSE PARTS

CHECKING CONTENTS

Check the contents of your miter saw carton to make

sure that you have received all parts. In addition to this

instruction manual, the carton should contain:

TOOLS NEEDED FOR ASSEMBLY CARTON CONTENTS

Blade wrench

(screwdriver+

6 mm hex key)

Flat bladed

screwdriver

4 mm hex key

Framing square

Triangle square

Adjustable wrench

and/or 13 mm wrench

ITEM DESCRIPTION QUANTITY

A.

B.

C.

D.

E.

A

B

C

D

Miter saw

Material clamp

Miter lock handle

Dust bag

Blade wrench

1

10

E

KNOW YOUR MITER SAW

11

Upper blade guard

Motor

Self-retracting lower blade guard

Base

Miter lock handle

Bevel lock handle

Bevel scale

Mounting hole

Hand hold

Table insert

Motor brush

Miter scale

Carry handle

Head lock knob

Dust port

Guide fence

Hand hold

Wrench storage

Locking button

(extend the angle of

inclination by +/- 3°)

Miter detent

Miter table

Arbor lock

Switch handle

Material clamp

Miter detent lock lever

ON/OFF Trigger switch

Made

of shock-resistant, see-through plastic that provides

protection from each side of the blade. It retracts over

the upper blade guard as the saw is lowered into

the workpiece.

WOODWORKING TERMS

The shaft on which a blade is mounted.

Allows the user to stop the blade from

rotating while tightening or loosening the blade screw

during blade replacement or removal.

A cutting operation made with the blade

at any angle other than 90° to the miter table.

A cut that removes a wedge from a

block of wood so that the end (or part of the end) is angled

at other than 90°.

A cut made using both a

miter angle and a bevel angle at the same time.

A cutting operation made across the grain

of the workpiece.

Performing a cut without using a fence

(guide), hold down or other proper device to prevent the

workpiece from twisting during the cutting operation. Do

not perform any operation freehand. Use a clamp or vise

wherever possible.

A sticky sap from wood products.

Misalignment of the blade.

KERF The material removed by the blade in a through

cut, or the slot produced by the blade in a non-through

or partial cut.

A hazard that can occur when the blade

binds or stalls, throwing the workpiece back toward the

operator.

An angle cut made across the width of the

workpiece.

The area between the marked lines

on the left and right side of the miter-table base. This zone

is identified by No-Hands Zone symbols inside the lines

marked on the miter table base.

Any cutting operation where the

blade does not extend completely through the thickness

of the workpiece.

GLOSSARY OF TERMS

COMPOUND MITER SAW TERMS

Supports the table, holds accessories and allows

for workbench or leg set mounting.

Locks the miter saw at a desired

bevel angle.

To measure the bevel angle of the saw

blade -3° to 48° left.

Helps to keep the workpiece from moving

when sawing.

Helps protect your hands from

the blade in the raised position, it retracts as the blade is

lowered.

MITER LOCK HANDLE Used to rotate the table, and to

rotate the saw to a right or left cutting position.

Measures the miter anlge 0° to 48° left

and right.

To mount the miter saw to a stable

surface.

To start the tool, squeeze

the trigger. Release the trigger to turn off the miter saw.

Locks the miter saw at

a preset positive stop for the desired miter angle.

Locks the miter saw in the lowered

position for compact storage and transportation.

May be on left or right fence or base

to securely clamp the workpiece.

The switch handle contains the trigger

switch. The blade is lowered into the workpiece by pushing

down on the handle. The saw will return to its upright

position when the hanlde is released.

For carrying and transporting the

miter saw.

An electric brake has been provided

to quickly stop blade rotation after the switch is released.

Read and understand for your own

safety. Make sure all labels are present on machine and

legible.

Convenient storage to prevent

misplacing the blade wrench.

12

WARNING

The operation of any saw can result in foreign objects being thrown into your eyes, which can result in severe eye damage.

Before starting power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield

when needed. We recommend wide vision safety mask for use over eyeglasses or standard safety glasses with side

shields.

Any cutting operation where the

blade extends completely through the thickness of the

workpiece.

The item being cut. The surfaces of a

workpiece are commonly referred to as faces, ends and

edges.

A plate inserted in the miter saw’s table

that alllows for blade clearance.

GLOSSARY OF TERMS

A sticky sap that has hardened.

The number of

turns completed by a spinning object in one minute.

The area of the workpiece or table

top directly in line with the travel of the blade or the part

of the workpiece which will be cut.

The distance between two saw blades tips, bent

outward in opposite directions to each other. The further

apart the tips are, the greater the set.

13

4. Push down the switch handle (3) and pull out the head

lock knob (4).

5. Gently release the downward pressure and allow the

arm to rise to its full height, remove the foam (5) under

the motor.

6. Holding the miter lock handle (2) while press down on

the miter detent lock lever (6), to move the table to 0°,

tighten the miter lock handle.

7. Unlock the bevel lock handle (7), tilting cutting arm to

0°, tighten bevel lock handle.

ASSEMBLY AND ADJUSTMENTS

Estimated Assembly Time: 2 Minutes

ASSEMBLY INSTRUCTIONS

WARNING

To avoid injury, do not connect this miter saw to a power

source until it is completely assembled and adjusted and

you have read and understood the operator’s manual.

WARNING

To reduce the risk of injury, turn unit off and disconnect

An accidental start-up can cause injury.

WARNING

Always make sure the miter saw is securely mounted to

a workbench or approved workstand. Failure to heed this

warning can result in serious personal injury.

CAUTION

Many of the illustrations in this manual show only portions

of the miter saw. This is intentional so that we can clearly

show points being made in the illustrations. Never operate

the saw without all guards securely in place and in good

operating condition.

1. Remove the saw from the packing material carefully

using the carrying handle (1). Place the saw on a

smooth, flat surface such as a workbench or strong

table.

2. This saw has been shipped with the miter table 48°

right & cutting arm bevel 15° left and the saw arm

secured in the down position.

3. Assemble miter lock handle (2) to the miter saw control

arm.

14

1

2

4

5

3

1

6

2

1

WARNING

TRANSPORTING THE SAW (Fig. F-G)

Fig. G

WARNING

INSTALL THE DUST BAG (FIG. H)

NOTE:

15

3

2

3

1

7

WARNING

IMPORTANT:

Fig. F

Fig. E

WARNING

1

3

2

INSTALL THE MATERIAL CLAMP ASSEMBLY (FIG. J)

NOTE:

CAUTION

WARNING

To install the material clamp:

Fig. J

REMOVE AND INSTALL THE TABLE INSERT (FIG. I)

Fig. H Fig. I

16

3

2

3

2

1

2

1

1 2

Fig. M

NOTE:

Fig. L

WARNING

REMOVE BLADE (FIG. K-N)

NOTE:

Fig. K

NOTE:

Fig. N

REMOVE AND INSTALL THE BLADE (FIG. K-N)

17

3

8

7

5

6

75

5

8

10

3

7

3

2

1

WARNING

NOTE:

WARNING

MOUNTING THE MITER SAW (FIG. O-Q)

WARNING

NOTE:

Fig. P Stationary use

18

1

5

6

7

2

3

8

10

INSTALLING BLADE (FIG. L-N)

NOTE:

MOUNTING INSTRUCTIONS

For stationary use,

Fig. O

NOTE:

For portable use,

Fig. Q

CAUTION

WARNING

ADJUSTMENT INSTRUCTIONS

BEVEL STOP ADJUSTMENT (Fig. R-V)

WARNING

90° (0°) BEVEL ADJUSTMENT (Fig. R-S)

NOTE:

Fig. S

Fig. R

90° (0°) BEVEL POINTER ADJUSTMENT (Fig. T)

Fig. T

5

7

8

10

1

3

2

6

11

12

Fig. V

Fig. X

MITER ANGLE POINTER ADJUSTMENT (Fig. Y)

Fig. Y

45° BEVEL ADJUSTMENT (Fig. U-V)

NOTE:

Fig. U

ADJUSTING FENCE SQUARENESS (Fig. W-X)

NOTE:

CAUTION

Fig. W

20

2

1

2

3

5

3

1

2

13

1

12

1

115

Page is loading ...

Porter Cable PXMS12ISB Operating instructions

Porter Cable PXMS12ISB Operating instructions

Other documents