1
12 IN. (305 MM)
COMPOUND MITER SAW
SIERRA INGLETEADORA COMPUESTA
DE 305MM (12 PULG.)
Instruction Manual
Manual de instrucciones
Español: Página 32
www.portercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS DE
SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
CATALOG NUMBER
PXMS12ISB
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS
SECTION
PRODUCT SPECIFICATIONS.....................................................................................................................
CALIFORNIA PROPOSITION 65.................................................................................................................
SAFETY GUIDELINES - DEFINITIONS ......................................................................................................
POWER TOOL SAFETY..............................................................................................................................
MITER SAW SAFETY..................................................................................................................................
ELECTRICAL REQUIREMENTS AND SAFETY..........................................................................................
TOOLS NEEDED FOR ASSEMBLY............................................................................................................
CARTON CONTENTS.................................................................................................................................
KNOW YOUR COMPOUND MITER SAW...................................................................................................
GLOSSARY OF TERMS..............................................................................................................................
ASSEMBLY AND ADJUSTMENTS..............................................................................................................
OPERATION................................................................................................................................................
MAINTENANCE...........................................................................................................................................
TROUBLESHOOTING GUIDE.....................................................................................................................
ACCESSORIES AND ATTACHMENTS.......................................................................................................
REPLACEMENT PARTS LIST.....................................................................................................................
WARRANTY.................................................................................................................................................
PAGE
2
3
3
4
6
8
10
10
11
12
14
21
27
28
29
30
31
Motor ......................
Speed (no load).......
Double Insulated.....
Saw Blade ..............
Arbor Size...............
Dust Port Size.........
Bevel Range............
Miter Range.............
Weight.....................
120 V AC, 60 Hz, 15 A
3800 RPM
Yes
12 in (305 mm) 40T
Carbide-tipped
1 in. (25.4 mm)
1 1/4 in. (31.75 mm)
-3° - 48°
0° - 48° R & L
35.2 lbs (16 kg)
CUTTING CAPACITY (Dimensional lumber)
Cross Cut 0° x 0° .....................
Miter Cut 45° x 0°......................
Bevel Cut 0° x 45°.....................
Compound Cut 45° x 45°..........
MITER/BEVEL POSITIVE STOP ANGLES
Miter Detent Stops ...................
Bevel Positive Stops.................
4 x 6 in., 2 x 8 in.
(101.6 x 152.4 mm, 50.8 x 203.2 mm)
4 x 4 in. (101.6 x 101.6 mm)
2 x 6 in. (50.8 x 152.4 mm)
2 x 4 in. (50.8 x 101.6 mm)
0°, 15°, 22.5°, 31.6°, 45° , 48° R & L
-3°, 0°, 45°, 48°
WARNING
electrical circuit for your tools.
way.
2017/07
Printed in China
2
CALIFORNIA PROPOSITION 65
SAFETY GUIDELINES - DEFINITIONS
WARNING
WARNING
WARNING ICONS
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION DOUBLE INSULATED CONSTRUCTION
WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields.
WEAR RESPIRATORY AND HEARING PROTECTION: Always wear respiratory and hearing protection.
READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce the risk of injury, user and all bystanders
must read and understand instruction manual before using this product.
CAUTION
WARNING
DANGER
CAUTION
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which,
if not avoided, may result in property damage.
KEEP HANDS AWAY FROM THE MOVING PART AND CUTTING SURFACE: Failure to keep your hands
away from the moving part and cutting surface will result in serious personal injury.
SUPPORT AND CLAMP WORK
3
12. ALWAYS WEAR EYE PROTECTION. Any
power tool can throw foreign objects into the
eyes and could cause permanent eye damage.
ALWAYS wear Safety Goggles (not glasses)
that comply with ANSI Safety standard Z87.1.
Everyday eyeglasses have only impact–resistant
lenses. They ARE NOT safety glasses. NOTE: Glasses
or goggles not in compliance with ANSI Z87.1 could
seriously injure you when they break.
13. WEAR A FACE MASK OR DUST MASK.
Sawing operation produces dust.
14. SECURE WORK. Use clamps or a vise to
hold work when practical. It is safer than
using your hand and it frees both hands
to operate the tool.
15. DISCONNECT TOOLS FROM POWER SOUCE
before servicing, and when changing accessories
such as blades, bits and cutters.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in the OFF position
before plugging the tool in.
17. USE RECOMMENDED ACCESSORIES. Consult this
Instruction Manual for recommended accessories.
The use of improper accessories may cause risk of
injury to yourself or others.
18. NEVER STAND ON THE TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. CHECK FOR DAMAGED PARTS. Before further
use of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function
– check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced.
20. NEVER LEAVE THE TOOL RUNNING UNATTENDED.
. Do not walk away from
a running tool until the blade comes to a complete
stop and the tool is unplugged from the power source.
21. DO NOT OVERREACH. Keep proper footing and
balance at all times.
22. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
23. DO NOT use power tool in presence of flammable
liquids or gases.
POWER TOOL SAFETY
GENERAL SAFETY INSTRUCTIONS
BEFORE USING THIS POWER TOOL
Safety is a combination of common sense, staying alert
and knowing how to use your power tool.
To avoid mistakes that could cause serious
Failure to follow all instructions listed below may
1. READ and become familiar with the entire
Instruction Manual. LEARN the tool’s
application, limitations and possible hazards.
2. KEEP GUARDS IN PLACE and in working order.
3. REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning ON.
4. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
5. DO NOT USE IN DANGEROUS ENVIRONMENTS
Do not use power tools in damp locations, or expose
them to rain or snow. Keep work area well lit.
6. KEEP CHILDREN AWAY. All visitors and bystanders
should be kept a safe distance from work area.
7. MAKE WORKSHOP CHILD PROOF with padlocks,
master switches or by removing starter keys.
8. DO NOT FORCE THE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE THE RIGHT TOOL. Do not force the tool or an
attachment to do a job for which it was not designed.
10. USE PROPER EXTENSION CORDS. Make sure
your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An
undersized cord will result in a drop in line voltage
and in loss of power which will cause the tool to
overheat. The table on page 9 shows the correct size
to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
11. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
WARNING
4
26. WEAR HEARING PROTECTION. to reduce
the risk of induced hearing loss.
POWER TOOL SAFETY
24. DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medicationn that
could affect your ability to use the tool properly.
25. Dust generated from certain materials can be
hazardous to your health. Always operate saw in
well-ventilated area and provide for proper dust
removal.
5
18. MAKE SURE the blade is not contacting the workpiece
before the switch in turned ON.
19. IMPORTANT: After completing the cut, release the
trigger and wait for the blade to stop before returning
the saw to the raised position.
20. MAKE SURE the blade has come to a complete stop
before removing or securing the workpiece. Changing
the workpiece angle or changing the angle of the
blade.
21. NEVER cut metals or masonry products with this tool.
This miter saw is designed for use on wood and
wood-like products.
22. NEVER cut small pieces. If the workpiece being cut
would cause your hand or fingers to be within 9-1/2
in. (240 mm) of the saw blade, the workpiece is too
small.
23. PROVIDE adequate support to the sides of the saw
table for long workpieces.
24. NEVER use the miter saw in an area with flammable
liquids or gases.
25. NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or otherwise damage the
material.
26. SHUT OFF the power before servicing or adjusting
the tool.
27. DISCONNECT the saw from the power source and
clean the machine when finished using.
28. MAKE SURE the work area is clean before leaving
the machine.
29. SHOULD any part of your miter saw be missing,
damaged, or fail in any way, or any electrical
component fail to perform properly, lock the switch
and remove the plug from the power supply outlet.
Replace missing, damaged, or failed parts before
resuming operation.
30. Because of the downward cutting motion, your safety
requires that you stay very alert to keep hands and
fingers away from the path that the blade travels.
31. Be sure all guards are in places and working. If
a guard seems slow to return to its normal position or
“hangs-up”, adjust or repair it immediately. Be alert at
all times - especially during repetitive, monotonous
operations. Don’t be lulled into carelessness due to a
false sense of security. Blades are extremely unforgiving.
Clean the lower guard frequently to help visibility and
movement. Unplug before adjustment or cleaning.
32. Abrasive cut-off wheels should not be used on miter
saw. Miter saw guards are not appropriate for abrasive
cut-off wheels.
MITER SAW SAFETY
SPECIFIC SAFETY INSTRUCTIONS FOR THIS
COMPOUND MITER SAW
1. DO NOT USE THIN KERF BLADES they can deflect
and contact guard an can cause possible injury to the
operator.
2. DO NOT operate the miter saw until it is completely
assembled and installed according to these
instructions.
3. IF YOU ARE NOT thoroughly familiar with the
operation of miter saws, seek guidance from your
supervisor, instructor or other qualified person.
4. ALWAYS hold the work firmly against the fence and
table. DO NOT perform any operation free hand (use
clamp wherever possible).
5. KEEP HANDS out of the path of the saw blade. If the
workpiece you are cutting would cause your hands to
be with 9-1/2 in. (240 mm) of the saw blade, the
workpiece should be clamped in place before making
the cut.
6. BE SURE the blade is sharp, runs freely and is free
of vibration.
7. ALLOW the motor to come up to full speed before
starting a cut.
8. KEEP THE MOTOR AIR SLOTS CLEAN and free of
chips or dust.
9. ALWAYS MAKE SURE all handles are tight before
cutting, even if the table is positioned in one of the
positive stops.
10. BE SURE both the blade and the flanges are clean
and the arbor bolt is tighten securely.
11. USE only blade flanges specified for your saw.
12. NEVER use blades larger in diameter than 12 in.
(305 mm).
13. NEVER apply lubricants to the blade when it is
running.
14. ALWAYS check the blade for cracks or damage
before operation. Replace a cracked or damged
blade immediately.
15. NEVER use blades recommended for operation at
less than 3800 RPM.
16. ALWAYS keep the blade guards in place and use at
all times.
17. NEVER reach around the saw blade.
6
39. WARNING: For your own safety, read instruction
manual before operating miter saw. Failure to obey
warnings in saw manual can result in serious injury.
Wear eye protection. Never operate saw without
proper, functional blade guard.
Never use if damage (i.e. breakage, cracks, loose
tips) is suspected.
Use a blade that can support the saw's maximum
speed.
Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
Unplug tool before changing blade or servicing tasks.
MITER SAW SAFETY
33. To avoid loss of control or placing hands in the path
of the blade, hold or clamp all material securely against
the fence when cutting. Do not perform operations
freehand.
34. Support long material at the same height as the saw
table.
35. After completing a cut, release the trigger switch and
allow the blade to come to a complete stop, then raise
the saw blade from the workpiece.
36. Lock the miter saw head in the down position during
transport or when not in use.
37. DRY RUN - It is important to know where the blade
will intersect with workpiece during cutting operation.
Always perform a simulated cutting sequence with the
power toll switch OFF to gain an understanding of the
projected path of the saw blade. At some extreme
angles, the right or left side fence might have to be
removed to ensure proper clearance prior to making
a cut.
38. Double insulation - When servicing, use only identical
replacement parts.
7
WARNING
1. Connect this saw to a 120 V circuit. This circuit must
not be less than a #12 wire with a 20 A time lag fuse
or a #14 wire with a 15 A time lag fuse. NOTE: When
using an extension cord on a circuit with a # 14 wire,
the extension cord must not exceed 25 feet in length.
2. If the motor will not start, release the trigger switch
immediately. UNPLUG THE SAW. Check the saw
blade to make sure it turns freely. If the blade is free,
try to start the saw again. If the motor still does not
start, refer to the TROUBLESHOOTING GUIDE.
3. If the tool suddenly stalls while cutting wood, release
the trigger switch, unplug the tool and free the blade
from the wood. The saw may now be started and the
cut finished.
4. FUSES may “bolw” or circuit breakers may trip
frequently if:
a: MOTOR is overload - overloading can occur if you
feed too rapidly or make too many start/stops in a
short time.
b: LINE VOLTAGE is more than 10% above or below
the nameplate voltage rating. For heavy loads, the
voltage at motor terminals must equal the voltage
specified on the nameplate.
c. IMPROPER or dull saw blades are used.
5. Most motor trouble may be traced to loose or incorrect
connections, overload, low voltage or inadequate
power supply wiring. Always check the connections,
the load and supply circuit if the motor doesn’t run
well. Check minimum gauge for the length of cord you
are using on the chart below.
GUIDELINES FOR EXTENSION CORDS
Use a proper extension cord. Make sure your extension
cord is good condition. When using an extension cord,
be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a
drop in line voltage, resulting in loss of power and
overheating. The table (on page 9) shows the correct size
to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
and in
good condition. Always replace a damaged extension cord
or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive
heat and damp or wet areas.
This
circuit must not be less than a #12 wire with a 20 A time
lag fuse or a #14 wire with a 15 A time lag fuse. NOTE:
When using an extension cord on a circuit with a #14
wire, the extension cord must not exceed 25 feet in length.
Before connecting the tool to the power line, make sure
the switch is in the OFF position and the electric current
is rated the same as the current stamped on the motor
nameplate, running at a lower voltage will damage the
motor.
ELECTRICAL REQUIREMENTS AND SAFETY
POWER SUPPLY AND MOTOR SPECIFICATIONS
The AC motor used in this saw is a universal, nonreversible
type. See “PRODUCT SPECIFICATIONS” section on
page 2.
to a 120 V, 15 A circuit and use a 15 A time delay fuse
ELECTRICAL REQUIREMENTS
DOUBLE INSULATED
The power tool is double insulated to provide a double
thickness or insulation between you and tool’s electrical
system. All exposed metal parts are isolated from the
internal metal motor components with protecting insulation.
When servicing, use only identical
replacement parts.
This saw has a plug that looks like the
one shown below:
WARNING
To avoid electrocution:
1. Use only identical replacement parts when servicing
a tool with double insulation. Servicing should be
performed by a qualified technician.
2. Do not use power tools in wet or damp locations or
expose them to rain or snow.
MOTOR SAFETY PROTECTION
IMPORTANT
To avoid motor damage, the motor should be blown out
or vacuumed frequently to keep sawdust from interfering
with the motor ventilation.
To reduce the risk of electrical shock, this saw has
a arized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug.
If it is still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any
way.
8
ELECTRICAL REQUIREMENTS AND SAFETY
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When using 120 volts only)
More Than
0
6
10
12
Not More Than
6
10
12
16
25ft.
18
18
16
14
50ft.
16
16
16
12
100ft.
16
14
14
150ft.
14
12
12
Not Recommended
9
WARNING
If any part is missing or damaged, do not attempt to
assemble the miter saw, or plug in the power cord until
the missing or damaged part is correctly replaced.
The use of attachments or accessories not listed
in this manual might be hazardous and could cause
serious personal injury.
TABLE OF LOOSE PARTS
CHECKING CONTENTS
Check the contents of your miter saw carton to make
sure that you have received all parts. In addition to this
instruction manual, the carton should contain:
TOOLS NEEDED FOR ASSEMBLY CARTON CONTENTS
Blade wrench
(screwdriver+
6 mm hex key)
Flat bladed
screwdriver
4 mm hex key
Framing square
Triangle square
Adjustable wrench
and/or 13 mm wrench
ITEM DESCRIPTION QUANTITY
A.
B.
C.
D.
E.
A
B
C
D
Miter saw
Material clamp
Miter lock handle
Dust bag
Blade wrench
1
1
1
1
1
10
E
KNOW YOUR MITER SAW
11
Upper blade guard
Motor
Self-retracting lower blade guard
Base
Miter lock handle
Bevel lock handle
Bevel scale
Mounting hole
Hand hold
Table insert
Motor brush
Miter scale
Carry handle
Head lock knob
Dust port
Guide fence
Hand hold
Wrench storage
Locking button
(extend the angle of
inclination by +/- 3°)
Miter detent
Miter table
Arbor lock
Switch handle
Material clamp
Miter detent lock lever
ON/OFF Trigger switch
Made
of shock-resistant, see-through plastic that provides
protection from each side of the blade. It retracts over
the upper blade guard as the saw is lowered into
the workpiece.
WOODWORKING TERMS
The shaft on which a blade is mounted.
Allows the user to stop the blade from
rotating while tightening or loosening the blade screw
during blade replacement or removal.
A cutting operation made with the blade
at any angle other than 90° to the miter table.
A cut that removes a wedge from a
block of wood so that the end (or part of the end) is angled
at other than 90°.
A cut made using both a
miter angle and a bevel angle at the same time.
A cutting operation made across the grain
of the workpiece.
Performing a cut without using a fence
(guide), hold down or other proper device to prevent the
workpiece from twisting during the cutting operation. Do
not perform any operation freehand. Use a clamp or vise
wherever possible.
A sticky sap from wood products.
Misalignment of the blade.
KERF The material removed by the blade in a through
cut, or the slot produced by the blade in a non-through
or partial cut.
A hazard that can occur when the blade
binds or stalls, throwing the workpiece back toward the
operator.
An angle cut made across the width of the
workpiece.
The area between the marked lines
on the left and right side of the miter-table base. This zone
is identified by No-Hands Zone symbols inside the lines
marked on the miter table base.
Any cutting operation where the
blade does not extend completely through the thickness
of the workpiece.
GLOSSARY OF TERMS
COMPOUND MITER SAW TERMS
Supports the table, holds accessories and allows
for workbench or leg set mounting.
Locks the miter saw at a desired
bevel angle.
To measure the bevel angle of the saw
blade -3° to 48° left.
Helps to keep the workpiece from moving
when sawing.
Helps protect your hands from
the blade in the raised position, it retracts as the blade is
lowered.
MITER LOCK HANDLE Used to rotate the table, and to
rotate the saw to a right or left cutting position.
Measures the miter anlge 0° to 48° left
and right.
To mount the miter saw to a stable
surface.
To start the tool, squeeze
the trigger. Release the trigger to turn off the miter saw.
Locks the miter saw at
a preset positive stop for the desired miter angle.
Locks the miter saw in the lowered
position for compact storage and transportation.
May be on left or right fence or base
to securely clamp the workpiece.
The switch handle contains the trigger
switch. The blade is lowered into the workpiece by pushing
down on the handle. The saw will return to its upright
position when the hanlde is released.
For carrying and transporting the
miter saw.
An electric brake has been provided
to quickly stop blade rotation after the switch is released.
Read and understand for your own
safety. Make sure all labels are present on machine and
legible.
Convenient storage to prevent
misplacing the blade wrench.
12
WARNING
The operation of any saw can result in foreign objects being thrown into your eyes, which can result in severe eye damage.
Before starting power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend wide vision safety mask for use over eyeglasses or standard safety glasses with side
shields.
Any cutting operation where the
blade extends completely through the thickness of the
workpiece.
The item being cut. The surfaces of a
workpiece are commonly referred to as faces, ends and
edges.
A plate inserted in the miter saw’s table
that alllows for blade clearance.
GLOSSARY OF TERMS
A sticky sap that has hardened.
The number of
turns completed by a spinning object in one minute.
The area of the workpiece or table
top directly in line with the travel of the blade or the part
of the workpiece which will be cut.
The distance between two saw blades tips, bent
outward in opposite directions to each other. The further
apart the tips are, the greater the set.
13
4. Push down the switch handle (3) and pull out the head
lock knob (4).
5. Gently release the downward pressure and allow the
arm to rise to its full height, remove the foam (5) under
the motor.
6. Holding the miter lock handle (2) while press down on
the miter detent lock lever (6), to move the table to 0°,
tighten the miter lock handle.
7. Unlock the bevel lock handle (7), tilting cutting arm to
0°, tighten bevel lock handle.
ASSEMBLY AND ADJUSTMENTS
Estimated Assembly Time: 2 Minutes
ASSEMBLY INSTRUCTIONS
WARNING
To avoid injury, do not connect this miter saw to a power
source until it is completely assembled and adjusted and
you have read and understood the operator’s manual.
WARNING
To reduce the risk of injury, turn unit off and disconnect
An accidental start-up can cause injury.
WARNING
Always make sure the miter saw is securely mounted to
a workbench or approved workstand. Failure to heed this
warning can result in serious personal injury.
CAUTION
Many of the illustrations in this manual show only portions
of the miter saw. This is intentional so that we can clearly
show points being made in the illustrations. Never operate
the saw without all guards securely in place and in good
operating condition.
1. Remove the saw from the packing material carefully
using the carrying handle (1). Place the saw on a
smooth, flat surface such as a workbench or strong
table.
2. This saw has been shipped with the miter table 48°
right & cutting arm bevel 15° left and the saw arm
secured in the down position.
3. Assemble miter lock handle (2) to the miter saw control
arm.
14
1
2
4
5
3
1
6
2
2
1
WARNING
TRANSPORTING THE SAW (Fig. F-G)
Fig. G
WARNING
INSTALL THE DUST BAG (FIG. H)
NOTE:
15
3
2
3
1
7
WARNING
IMPORTANT:
Fig. F
Fig. E
WARNING
1
3
2
INSTALL THE MATERIAL CLAMP ASSEMBLY (FIG. J)
NOTE:
CAUTION
WARNING
WARNING
To install the material clamp:
Fig. J
REMOVE AND INSTALL THE TABLE INSERT (FIG. I)
Fig. H Fig. I
16
3
2
3
2
1
2
1
1 2
Fig. M
NOTE:
Fig. L
WARNING
REMOVE BLADE (FIG. K-N)
NOTE:
Fig. K
NOTE:
Fig. N
REMOVE AND INSTALL THE BLADE (FIG. K-N)
17
3
8
7
5
6
75
5
8
10
3
7
3
2
1
WARNING
NOTE:
WARNING
MOUNTING THE MITER SAW (FIG. O-Q)
WARNING
NOTE:
Fig. P Stationary use
18
1
1
1
1
5
6
7
2
3
8
10
INSTALLING BLADE (FIG. L-N)
NOTE:
NOTE:
MOUNTING INSTRUCTIONS
For stationary use,
Fig. O
NOTE:
For portable use,
Fig. Q
CAUTION
WARNING
ADJUSTMENT INSTRUCTIONS
BEVEL STOP ADJUSTMENT (Fig. R-V)
WARNING
90° (0°) BEVEL ADJUSTMENT (Fig. R-S)
NOTE:
Fig. S
Fig. R
90° (0°) BEVEL POINTER ADJUSTMENT (Fig. T)
Fig. T
5
7
8
10
1
1
3
2
6
11
12
Fig. V
Fig. X
MITER ANGLE POINTER ADJUSTMENT (Fig. Y)
Fig. Y
45° BEVEL ADJUSTMENT (Fig. U-V)
NOTE:
Fig. U
ADJUSTING FENCE SQUARENESS (Fig. W-X)
NOTE:
CAUTION
Fig. W
20
2
1
2
3
5
3
1
2
13
1
12
1
115
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/