PC-HELPER
High-Speed Bi-directional
Digital I/O Board for PCI Express
DIO-32DM3-PE
User’s Guide
CONTEC CO., LTD.
DIO-32DM3-PE
i
Check Your Package
Thank you for purchasing the CONTEC product.
The product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or missing
items, contact your retailer.
Product Configuration List
- Board [DIO-32DM3-PE] …1
- SC Cable (10cm) …1
- First Step Guide …1
- Disk *1 [API-PAC(W32)] …1
- Warranty Certificate …1
- Serial Number Label …1
*1 The bundled disk contains the driver software and User’s Guide (this guide)
DIO-32DM3-PE SC Cable
Disk
[API-PAC(W32)]
First Step Guide
First Step
Guide
Serial Number Label
Warranty Certificate
Warranty
Certificate
ii
DIO-32DM3-PE
Copyright
Copyright 2018 CONTEC CO., LTD. ALL RIGHTS RESERVED
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document. The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft, Windows and Windows NT are trademarks of Microsoft Corporation. Other brand and
product names are trademarks of their respective holder.
DIO-32DM3-PE
iii
Table of Contents
Check Your Package................................................................................................................. i
Copyright ..................................................................................................................................................... ii
Trademarks .................................................................................................................................................. ii
Table of Contents ....................................................................................................................................... iii
1. BEFORE USING THE PRODUCT 1
About the Board .......................................................................................................................................... 1
Features ................................................................................................................................................. 1
Support Software.................................................................................................................................. 3
Cable & Connector (Option) ............................................................................................................... 4
Accessories (Option) ........................................................................................................................... 4
Customer Support ........................................................................................................................................ 5
Web Site................................................................................................................................................ 5
Limited Three-Years Warranty .................................................................................................................. 5
How to Obtain Service ................................................................................................................................ 5
Liability ........................................................................................................................................................ 5
Safety Precautions ....................................................................................................................................... 6
Safety Information ............................................................................................................................... 6
Handling Precautions ........................................................................................................................... 7
Environment ......................................................................................................................................... 9
Inspection.............................................................................................................................................. 9
Storage .................................................................................................................................................. 9
Disposal ................................................................................................................................................ 9
2. SETUP 11
What is Setup? ........................................................................................................................................... 11
Using the Board under Windows Using the Driver Library API-PAC(W32) .............................. 11
Step 1 Installing the Software .................................................................................................................. 12
About the driver to be used ............................................................................................................... 12
Select API-DIO(WDM)..................................................................................................................... 14
Step 2 Setting the Hardware.............................................................................................................. 15
Parts of the Board and Factory Defaults .......................................................................................... 15
Setting the Board ID .......................................................................................................................... 16
Setting the Pull-Up............................................................................................................................. 16
Plugging the Board ............................................................................................................................ 19
Step 3 Installing the Hardware ................................................................................................................. 20
Turning on the PC .............................................................................................................................. 20
Found New Hardware Wizard Setting .................................................................................................. 21
Step 4 Initializing the Software ................................................................................................................ 22
Step 5 Operation Checks .......................................................................................................................... 24
iv
DIO-32DM3-PE
Check Method .................................................................................................................................... 24
Setup Troubleshooting .............................................................................................................................. 27
Symptoms and Actions ...................................................................................................................... 27
3. EXTERNAL CONNECTION 29
How to connect the connectors ................................................................................................................ 29
Connector shape ................................................................................................................................. 29
Connector Pin Assignment................................................................................................................ 30
Relationships between API-PAC(W32) Logical Ports/Bits and Connector Signal Pins ............. 31
Connection method to the external device -Data I/O- ........................................................................... 33
Connecting the data I/O signal(DIOA0* - DIOD0*)...................................................................... 33
Detailed Data I/O Signal Circuit ...................................................................................................... 33
Connection method to the external device -Control I/O- ...................................................................... 34
Connection to the control signal (EXT**)....................................................................................... 34
Detailed Control Input Signal Circuit .............................................................................................. 34
Detailed Control Output Signal Circuit ........................................................................................... 35
What is the Control Signal ? ............................................................................................................. 35
Synchronization Control Connectors ...................................................................................................... 38
SC Connectors.................................................................................................................................... 38
Connecting the SC Connectors (CN2,CN3) .................................................................................... 39
4. FUNCTION 41
Function Outline ........................................................................................................................................ 41
Overview ............................................................................................................................................ 41
Sampling function / generating function ......................................................................................... 41
Bus Master Transfer .......................................................................................................................... 41
Interrupt (at the time of bus master transfer) ................................................................................... 42
Status, count ....................................................................................................................................... 42
Sampling function ..................................................................................................................................... 43
Sampling control ................................................................................................................................ 43
Generating function................................................................................................................................... 44
Generating control ............................................................................................................................. 44
General-purpose I/O function .................................................................................................................. 45
Data input ........................................................................................................................................... 45
Data output ......................................................................................................................................... 45
Monitoring the output data................................................................................................................ 45
Interrupt Control Function........................................................................................................................ 46
Disabling/enabling Interrupts ........................................................................................................... 46
Clearing the Interrupt Status and Interrupt Signal .......................................................................... 46
5. ABOUT SOFTWARE 47
About Software for Windows .................................................................................................................. 47
DIO-32DM3-PE
v
Accessing the Help File ..................................................................................................................... 47
Using Sample Programs .................................................................................................................... 48
Uninstalling the Driver Libraries...................................................................................................... 49
6. ABOUT HARDWARE 51
Hardware specifications............................................................................................................................ 51
Block Diagram ........................................................................................................................................... 53
Differences between DIO-32DM3-PE, DIO-32DM2-PE, DIO-32DM-PE and PIO-32DM(PCI)
..................................................................................................................................................................... 54
vi
DIO-32DM3-PE
1. Before Using the Product
DIO-32DM3-PE
1
1. Before Using the Product
This chapter provides information you should know before using the product.
About the Board
This product is a PCI Express bus-compliant interface board that supports transfer by bus mastering and
performs input/output between the external device and digital signal. This product features unisolated
LVTTL level (Operating voltage : 3.3V) I/O 32channels and you can select input / output in 16 units.
Bus master transfer makes it possible to sample quickly large data with transfer rate at 50MHz
maximum. It can be used as a pattern generator that outputs arbitrary digital patterns at high speed.
It can also be used as a general-purpose I/O board when bus mastering is not used.
Windows driver is bundled with this product.
Using the dedicated library VI-DAQ makes it possible to create each application for LabVIEW.
Features
-
32channels of unisolated LVTTL level I/O (32 input channels / each 16channels for I/O / 32 output
channels are selected.)
This product has the 32channels (operating voltage 3.3VDC, positive logic) of unisolated LVTTL level
I/O whose response speed is 20nsec. They can be used for 32bit input, 16bit input plus 16bit output, or
for 32bit output.
Other than I/O bit, this product has the control signal (clock, start, stop and handshake signal (REQ,
ACK) that can control starting and stopping the sampling (input) / generating (output)).
- Sampling and generating with transfer rate at 50MHz maximum
Bus master transfer makes it possible to sample (input) or generate (output) large data with transfer rate
at 50MHz maximum. As the sampling and generating features have their own bus mastering blocks
each made up of two independent channels, the board can generate 16 signals while sampling 16
signals.
- A synchronization control connector is provided for synchronized control of multiple boards.
A synchronization control connector is provided for synchronized control of up to 16 boards. It is also
easy to synchronize operation with other CONTEC boards that have a synchronization control
connector.
- You can use Max. 4 input signals as interrupt request signals at the time of using the general-purpose
I/O.
You can use Max. 4 input signals as interrupt request signals and also disable or enable the interrupt in
bit units at the time of using the general-purpose I/O.
- Windows compatible driver libraries are attached.
Using the attached driver library API-PAC(W32) makes it possible to create applications of Windows.
In addition, a diagnostic program by which the operations of hardware can be checked is provided.
1. Before Using the Product
2
DIO-32DM3-PE
- You can use pull-up and the voltage selection.
At input points and control signals, you can use pull-up. In addition, the pull-up voltage can be selected
from the 3.3V and 5V. This feature allows you to easily connect and equipment with an output point of
the sink type.
- Functions and connectors are compatible with PCI compatible board PIO-32DM(PCI) and PCI
Express compatible board DIO-32DM2-PE, DIO-32DM-PE.
The functions same with PCI compatible board PIO-32DM(PCI) and PCI Express compatible board
DIO-32DM2-PE, DIO-32DM-PE are provided. In addition, as there is compatibility in terms of
connector shape and pin assignments, it is easy to migrate from the existing system.
- LabVIEW is supported by a plug-in of dedicated library.
Using the dedicated library makes it possible to make a LabVIEW application.
1. Before Using the Product
DIO-32DM3-PE
3
Support Software
You should use CONTEC support software according to your purpose and development environment.
Windows version of digital I/O driver
API-DIO(WDM)
[
Stored on the bundled disk driver library API-PAC(W32)]
The API-DIO(WDM) is the Windows version driver library software that provides products in the form of Win32 API
functions (DLL). Various sample programs such as Visual Basic and Visual C++, etc and diagnostic program
*1useful for checking operation is provided.
For more details on the supported OS, applicable language and new information, please visit the CONTEC’s Web site.
LabVIEW-support data acquisition library
DAQfast for LabVIEW
(Available for downloading (free of charge) from the CONTEC web site.)
This is a data collection library to use in the LabVIEW by National Instruments. With Polymorphic VI, our design
enables a LabVIEW user to operate seamlessly. Our aim is that the customers to perform easily, promptly what they
wish to do.
For more details on the library and download of
DAQfast for LabVIEW
, please visit the CONTEC’s Web site.
Data acquisition library for LabVIEW
VI-DAQ
(Available for downloading (free of charge) from the CONTEC web site.)
This is a VI library to use in National Instruments LabVIEW.
VI-DAQ is created with a function form similar to that of LabVIEW's Data Acquisition VI, allowing you to use
various devices without complicated settings.
For more details on the library and download of VI-DAQ, please visit the CONTEC’s Web site.
1. Before Using the Product
4
DIO-32DM3-PE
Cable & Connector (Option)
Shield Cable with 96-Pin Half-Pitch Connectors at Both Ends : PCB96PS-0.5P (0.5m)
: PCB96PS-1.5P (1.5m)
Shield Cable with 96-Pin D-SUB Connector at One End : PCA96PS-0.5P (0.5m)
: PCA96PS-1.5P (1.5m)
Accessories (Option)
Screw Terminal Unit (M3 x 96P) : EPD-96A *1*2
Screw Terminal Unit (M3.5 x 96P) : EPD-96 *1
Terminal Unit for Cables (M3 x 96P) : DTP-64A *1
*1 PCB96P or PCB96PS optional cable is required separately.
*2 "Spring-up" type terminal is used to prevent terminal screws from falling off.
* Check the CONTEC’s Web site for more information on these options.
1. Before Using the Product
DIO-32DM3-PE
5
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently
and comfortably.
Web Site
https://www.contec.com/
Latest product information
CONTEC provides up-to-date information on products.
CONTEC also provides product manuals and various technical documents in the PDF.
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Note! For product information
Contact your retailer if you have any technical question about a CONTEC product or need its price,
delivery time, or estimate information.
Limited Three-Years Warranty
CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and
workmanship for up to three years from the date of purchase by the original purchaser.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the
original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group
office, from which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
How to Obtain Service
For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please
obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you
purchased before returning any product.
* No product will be accepted by CONTEC group without the RMA number.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the
warrantor be liable for any incidental or consequential damages due to such defect or consequences that
arise from inexperienced usage, misuse, or malfunction of this device.
1. Before Using the Product
6
DIO-32DM3-PE
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting
in injury or death and the destruction of equipment and resources. Understand the meanings of these
labels to operate the equipment safely.
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury or in property damage.
DA
N
GE
R
WARNING
CAUTION
1. Before Using the Product
DIO-32DM3-PE
7
Handling Precautions
Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in
an explosion, fire, electric shock, or failure.
- There are switches and jumpers on this product that need to be set in advance.
Be sure to check these before installing to the expansion slot.
- Only set the switches and jumpers on this product to the specified settings.
Otherwise, this product may malfunction, overheat, or cause a failure.
- Do not strike or bend this product.
Otherwise, this product may malfunction, overheat, cause a failure or breakage.
- Do not touch this product's metal plated terminals (edge connector) with your hands.
Otherwise, this product may malfunction, overheat, or cause a failure.
If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.
- Do not install or remove this product to or from the expansion slot while the computer's power or
expansion unit is turned on.
Otherwise, this product may malfunction, overheat, or cause a failure.
Be sure that the personal computer power is turned off.
- Make sure that your PC or expansion unit can supply ample power to all the products installed.
Insufficiently energized products could malfunction, overheat, or cause a failure.
- The specifications of this product are subject to change without notice for enhancement and quality
improvement.
Even when using this product continuously, be sure to read the user’s guide and understand the
contents.
- Do not modify this product. CONTEC will bear no responsibility for any problems, etc., resulting
from modifying this product.
- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever
(including damages for loss of business profits) arising out of the use or inability to use this
CONTEC product or the information contained herein.
DANGER
CAUTION
1. Before Using the Product
8
DIO-32DM3-PE
FCC PART15 Class A Notice
EN55032 Class A Notice
Warning: Operation of this equipment in a residential environment could cause radio interference.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
NOTE
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
1. Before Using the Product
DIO-32DM3-PE
9
Environment
Use this product in the following environment. If used in an unauthorized environment, the product
may overheat, malfunction, or cause a failure.
Operating temperature
0 - 50
°
C
Operating humidity
10 - 90%RH (No condensation)
Corrosive gases
None
Floating dust particles
Not to be excessive
Inspection
Inspect the product periodically as follows to use it safely.
Storage
When storing this product, keep it in its original packing form.
(1) Put this product in the storage bag.
(2) Wrap it in the packing material, then put it in the box.
(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,
vibration, magnetism, and static electricity.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws and
municipal ordinances.
- Check that the board has
- Check that the bus connector
- The gold-plated leads of
～
～
no dust or foreign matter adhering.
of the board and its cable have
been plugged correctly.
the bus connector.
1. Before Using the Product
10
DIO-32DM3-PE
2. Setup
DIO-32DM3-PE
11
2. Setup
This chapter explains how to set up the board.
What is Setup?
Setup means a series of steps to take before the product can be used.
Different steps are required for software and hardware.
The setup procedure varies with the OS and software used.
Using the Board under Windows
Using the Driver Library API-PAC(W32)
This section describes the setup procedure to be performed before you can start developing application
programs for the board using the bundled disk “Driver Library API-PAC(W32)”.
Taking the following steps sets up the software and hardware. You can use the diagnosis program later
to check whether the software and hardware function normally.
Step 1 Installing the Software
Step 2 Setting the Hardware
Step 3 Installing the Hardware
Step 4 Initializing the Software
Step 5 Operation Checks
If Setup fails to be performed normally, see the “Setup Troubleshooting” section at the end of this
chapter.
2. Setup
12
DIO-32DM3-PE
Step 1 Installing the Software
This section describes how to install the Driver libraries.
Before installing the hardware in a PC, install "Driver Library API-PAC(W32)" from the
bundled media or download and install the latest edition of this software from the CONTEC web
site.
Although some user interfaces are different depending on the OS used, the basic procedure is the same.
About the driver to be used
Two Digital I/O drivers are available : API-DIO(WDM).
When using this product, use the advanced digital I/O driver "API-DIO(WDM)". The following
information is focused on setting up API-DIO(WDM).
If you use this product with digital input and output high-performance driver API-DIO (WDM).
2. Setup
DIO-32DM3-PE
13
Starting the Install Program
(1)
Load the bundled media [API-PAC(W32)] on your PC.
(2)
The API-PAC(W32) Installer window appears automatically.
If the panel does not appear, run (drive letter):\AUTORUN.exe.
(3)
Click on the [Install Development or Execution Environment] button.
Before installing the software, log in as a user with administrator privileges.
CAUTION
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/