Lightolier Ic Frame 3 3/4" Inc Install Instructions

Brand: Lightolier

Model: Ic Frame 3 3/4" Inc

Type: Install Instructions

This manual is also suitable for

INSTALLATION INSTRUCTIONS FOR LYTECASTER INCANDESCENT

PRE-WIRED MOUNTING FRAME

07-04/Rev-02

ISF:1102IC

FIG.3

FIG.4

FIG.5 FIG.6

FIG.7

FIG.8

FIG.11

FIG.12

MOUNTING

FRAME

MOUNTING

BAR

LOCKING

TABS

MOUNTING

BAR

LOCKING

CLIP

MOUNTING

FRAME

"PRY-OUT"

PLUG

FLEXIBLE

WIRE

CONNECTOR

JUNCTION

BOX

LIGHTING

UNIT

PLUMB

LINE

MARK

"ROTO-CLIP"

FASTENERS

MOUNTING

FRAME

SOCKET

"PRY-OUT"

PLUG

JUNCTION

BOX

JUNCTION

BOX

FLEXIBLE

CONDUIT

CONNECTOR

WITH VAPOUR BARRIER COVER: NºVBE (Order separately)

1. Select a location for the fixture.

2. Fasten the edge of the

vapour barrier cover under the wood joist. (Fig.1)

3. Install the fixture (see step A, B and C).

4. Install the ceiling vapour barrier. (Fig.2)

Note: Seal the edges of the vapour barrier cover and the vapour barrier.

(Fig.2)

FOR NEW CEILING:

A. MOUNTING BAR:

Note-1: The mounting bars are extensible from 12½" to 29" max.

Note-2: For off-centre installation, use the 20" expandable mounting bars

(Nº1964, order separately).

1. Insert the

mounting bars into the proper openings on the short side or the

long side of the

mounting frame. (Fig.4)

2. Align the

mounting bar with the bottom edge of the joist. (Fig.3)

3. Push in the

built-in nailer. (Fig.3)

B. MOUNTING FRAME:

1. Align the

mounting frame using the alignment marks. (Fig.10)

2. Install the

locking clip. (Fig.5)

Note-1: The ocking clip is also available separately

(Nº0098, order separately).

Note-2: To lock more securely into place fold the locking tabs. (Fig.4)

Note-3: Make sure that the opening in the mounting frame is clear before

cutting. (Fig.11)

C. WIRE-IN:

1. Remove the appropriate "

Pry-out plug". (Fig.6)

2. Insert the supply lead into the

junction box:

a) If using

FLEXIBLE CONDUIT: Use a BX connector (not provided). (Fig.7)

b) If using

FLEX WIRE: Insert under the wire connector. (Fig.8)

3. Connect the

ground lead. (Fig.9)

4. Connect the

white leads (NEUTRAL) together, and the black leads

(120V) together. (Fig.9)

D. CEILING:

1. Mark the position of the

lighting unit and close the ceiling. (Fig.10)

2. Cut an opening in the ceiling using the

mounting frame as a template.

(Fig.11)

3. Pull out the

socket. (Fig.12)

Note: The socket may be used for temporary lighting.

TRIM:

Install the trim using the appropriate sheet.

Note: For the series 1131 & 1133 (with the slope ceiling)

Position the

mounting frame with the junction box facing up. (Fig.13)

PLUMB

LINE

FIG.10

FIG.13

JUNCTION

BOX

MOUNTING

FRAME

WOOD JOIST

FIG.1 FIG.2

VAPOUR

BARRIER EXTENDER

VAPOUR BARRIER

EXTENDER

VAPOUR BARRIER

SILICONE

SEALER

OR OTHER

FIXTURE

FIG.9

INPUT (120V)

GROUND

THERMAL

PROTECTOR

BLACK

WHITE

JUNCTION

BOX

LAMP

BLACK

NEUTRAL (white)

MOUNTING

BAR

BUILT-IN

NAILER

WOOD

JOIST

INSTRUCTION SHEETINSTRUCTION SHEET

INSTRUCTION SHEET

Read and understand these instructions before installing the luminaire.

CAUTION: Branch circuit conductors must be rated 90°C minimum. To prevent electrical shock turn off electricity and check your

local electrical code and regulations. Consult a qualified electrician before installing.

WARNING: - Risk of fire: Transformer contains luminaire thermal protector. Use only replacement transformer obtained from

Lightolier CFI.

Lightolier Ic Frame 3 3/4" Inc Install Instructions

Brand: Lightolier

Model: Ic Frame 3 3/4" Inc

Type: Install Instructions

This manual is also suitable for

Download PDF

report

Lightolier Ic Frame 3 3/4" Inc Install Instructions

This manual is also suitable for

Lightolier Ic Frame 3 3/4" Inc Install Instructions

Related papers

Other documents