Mettler Toledo Short-formLabPac-M For PM balances Operating instructions
- Type
- Operating instructions
Short-form operating instructions
METTLER TOLEDO
LabPac-M
% formula
Formula weighing with entry of
the component weights in % of
the formulation weight
Differential weighing
Determination of weight changes
1. Weigh in
• Attachment of the terminal and insertion of the program cassette: see LabPac-M operating instructions.
• For automatic result recording, –Au-Prot– must be configured, see LabPac-M operating instructions.
• A detailed description of all application possibilities with the LabPac-M as well as practical examples can be
found in the LabPac-M operating instructions.
Calculation mode Switch with
• Weight difference in % of initial weight (initial weight = 100%)
• Weight difference in weight units
• Weight on backweighing in weight units
• Weight on backweighing in % of initial weight
(initial weight = 100%)
❊ The result is displayed in the calculation mode last used. As long as
the sample remains on the balance, a switch can be made to another
calculation mode.
Net total weighing
Weighing-in of any number of
components from zero, totalization
of individual weights
❊ In the totalization of
individual weights, these
steps are skipped.
2. Backweigh after (repeated)
treatment of samples
Clear
1
2
3
Diff.
weighing
max. 20 weighings
Re-Zero
g
g
g
g
Store
tare
Store
weight
Results
End
treatment and backweighing of all samples can be repeated
all weighed samples must be backweighed in the same order
treat samples
g
Re-Zero
%
g
❊
Diff.
weighing
Results
End
Reset
weigh in n components (total <100 %)
1
2
.
2
0 0
g
g
g
5
g
g
%
%
Re-Zero
Comp.
(%)
Re-zero
Comp.
(%)
Re-zero
Total
Total %
%
formula
Enter
Target
Enter
Print
fill to 100%
weigh in n components
3
7
.
5
ID
g
g
fill to target weight
g
g
g
g
Re-Zero
Net
total
Comp.
Enter
Re-zero
Last
Total
Print
❊
❊
activates the differential weighing
application and the 3 associated keys
stores the tare weight and sets the
display to zero
stores the net initial weight of the
sample
ends the weighing
determines the difference on
backweighing
activates the % formula application and
the 3 associated keys
start of the formulation target weight
entry in weight units
start of the component entry in % of the
target weight, adds the components to
the net total, sets the display to zero
call up of the last net total, switching of
the net total display from % to weight
units
activates the net total application and
the 3 associated keys
start of the component weight entry
© Mettler-Toledo GmbH 1999 704694 Printed in Switzerland 9909/7.12
Mettler-Toledo GmbH, Laboratory & Weighing Technologies, CH-8606 Greifensee, Switzerland
Phone +41-1-944 22 11, Fax +41-1-944 30 60, Internet: http://www.mt.com
LabPac-M keypad
start of the code entry, e.g. code for the
individual components of a formulation.
Code is cleared immediately following
printout
start of the date and time entry
date and time are stored until loss of
voltage
clear or correction key
print command key
completion/transfer of a numeric entry
storage of values (e.g. target weight,
weight of 1
st
component) to prevent loss
on power outage
start of the identification number entry,
e.g. formulation No., remains stored until
Reset pressed or power switched off
Totalization with the keys
F Ï ∏
If the GM303 Control Unit is attached or the
LabPac-M is used with SM scales or high-
capacity PM scales, the totalization of
individual weights can be performed without
the LabPac-M terminal.
Preparation
• Attach LabPac-M terminal
• Activate net total application
• Store application with
• Remove LabPac-M terminal
The scale can now be used for totalization.
Note
Clear the stored application with
switches between current component
weight and last net total
adds the actual component weight to the
net total, sets the display to zero
resets all entries except date, time and
stored values
∏
totalize n components
g
fill to target weight
g
g
g
g
Re-Zero
F
Ï
Diff.
weighing
%
formula
Net
total
ID
Date Time
Reset
Store
tare
Target
Comp.
Clear
Store
weight
Comp. %
Re-zero
Re-zero
Print
Results
.
-
Enter
End
Total
Total %
Last
Total
% formulation
Differential weighing
Net total weighing
Code
7
8
9
4
5
6
1
2
3
0
Save
-
Save
-
Save
Reset
Diff.
weighing
Store
tare
Store
weight
Results
End
Total
Total %
Comp.
%
Re-zero
Target
%
formula
Net
total
Comp.
Re-zero
Last
Total
ID
7
Code
4
Date
8
Time
9
-
Save
Reset
Clear
Print
Enter
P704694
-
1
-
2
Mettler Toledo Short-formLabPac-M For PM balances Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Mettler Toledo LabPac-M For PM balances Operating instructions
-
-
-
-
-
-
-
-
-