4
PREPARATION
A complete electric fireplace consists of two parts; the mantle and the electric fireplace insert.
Each is packed in a separate carton. Always use the electric insert with the matching mantle.
Remove all parts from the carton and place them on a clean, soft, dry surface. Check the parts list to
make sure nothing is missing. Dispose of packaging materials properly. Please recycle.
PARTS & HARDWARE
Electric Insert (not shown) 1
A
Hearth 1
B
Left Side Panel 1
C
Right Side Panel 1
D
Left Front Panel 1
E
Right Front Panel 1
F
Header 1
G
Mantel 1
J
M4x25 Wood Screws 20
K
Insert Mounting Clips 4
L
Insert Mounting Screws
4
H
ANTI-TIP SAFETY KIT
Wall Anchors (H1) 2
Brackets (H2) 2
5/8” Screws (H3) 2
1-3/8” Screws (H4) 2
Cable Tie (H5) 1
Note: A Phillips screwdriver is required for assembly, but is not included.
A
F
E
D
B
C
G
H
5
ASSEMBLY
STEP 1. Thread wood screw (J) through bottom connector on left side panel (B) and into hole in
hearth (A). Secure with Phillips screwdriver. DO NOT over-tighten. Repeat for right side panel (C).
STEP 2. Thread screws (J) through connectors in right side panel (C) and into right front panel (E).
Thread screw (J) through connector on right front panel (E) and into hearth (A). Secure with Phillips
screwdriver. DO NOT over-tighten. Repeat for left front panel (D).
C
B
A
You will need:
J x 8
B
J
You will need:
J x 2
J
C
A
D
E
Rear
Rear
Front
Front
6
STEP
3
.
From behind, thread screws (J) through holes in header (F) and into holes in left and right
front panels (D/E). Secure with Phillips screwdriver. DO NOT over-tighten.
STEP
4
.
Set mantel (G) on top of hearth assembly. Thread screws (J) through holes in side panels
(B/C) and header (F) and into mantel (G). Secure with Phillips screwdriver. DO NOT over-tighten.
C
J
D
E
A
C
2
B
You will need:
J x 4
You will need:
J x 6
F
E
D
A
B
J
F
G
Front
Rear
Rear
Front
7
ANT-TIP SAFETY KIT INSTALLATION
A. Secure one bracket (H2) to an inside rear surface of the mantel with two 5/8” screws (H3).
Tighten the screws with a Phillips screwdriver. DO NOT over-tighten. B. Position the mantel in the
desired location and mark the wall where the second bracket will be mounted.
A. Secure the second bracket (H2) with two 1-3/8” screws (H4). Screw directly into the wall studs. [If
no studs are available, drill two holes and tap the anchors (H1) into the holes. Then screw the two
screws through the bracket into the anchors.] B. Tighten all screws with a Phillips screwdriver. DO
NOT over-tighten. C. Loop the cable tie (H5) through the two brackets and lock the ends together.
Tug on the cable tie and brackets to make sure they are secure.
WARNING! This cable may reduce possible risk of injury if the fireplace is improperly
handled. But, it is not a substitue for proper adult supervision.
WARNING! This anti-tip safety kit is only a deterrent. It is not a substitute for proper
adult supervision. NEVER leave children unattended near this product!
Mantel
H3
H2
Mark the
wall
H3
H3
H3
H5
H5
H2
H2
H4
H
4
H1
H
1
/
