Desa Tech CGHRC4 Owner's manual
- Category
- Fireplaces
- Type
- Owner's manual
DESA Wireless Hand-Held Remote Control Sets
For Use With DESA International Remote Ready Log Sets and Fireplace Systems
For More Information See Owner’s Manual
INSTALLING REMOTE
RECEIVER UNIT
1. Disconnect switch wires from the con-
trol valve.
2. Remove screws and nuts.
3. Remove switch plate (see Figure 1).
Discard after removing.
4. Install remote receiver unit onto gas log
heater base using clips (2) and insulat-
ing washers provided.
5. Push clips firmly into place (see Fig-
ure 2).
6. Connect wires as shown in Figure 3.
Note:
On yellow flame models, reuse pro-
vided phillips head screws and reinstall heat
shield over receiving unit.
INSTALLING WIRELESS
REMOTE CONTROL
ACCESSORY
Two 9-volt alkaline batteries (not included)
are required to operate this heater with the
wireless hand held remote control set. One
battery must be installed in the receiver and
one in the hand-held remote control unit.
Note:
Only use alkaline batteries.
Installing 9-Volt Battery (Not
Included) in Receiver
1. Locate back of receiver under front
burner of heater.
2. Locate the battery clip mounted on the
back of the receiver.
3. Slide a 9-volt battery through the clip.
4. Attach the terminal wires to the battery.
Figure 1 - Switch Plate and Wiring Harness
(Switch Plate and Orientation May Vary
Depending On Model)
Figure 3 - Connecting Wires
Valve
Wire From
Receiver
Figure 2 - Installing Remote Receiver
Installing 9-Volt Battery (Not
Included) in Hand-Held Remote
Control Unit
1. Remove battery cover on back of re-
mote control unit.
2. Attach terminal wires to the battery.
Place battery into the battery housing.
3. Replace battery cover onto remote con-
trol unit.
Figure 4 - Installing Receiver on the Back
of the Base
Battery Clip
9-Volt Battery
Receiver
Terminal
Wires
Figure 5 - Installing Battery in Hand-Held
Remote Control Unit
Battery Cover
9-Volt
Battery
Terminal
Wires
Remote
Control Unit
Battery
Housing
Figure 6 - Installing Battery in Hand-Held
Remote Control Unit (Thermostat Model)
Battery Cover
9-Volt
Battery
Terminal Wires
Remote Control Unit
Battery Housing
REMOTE OPERATION
NOTICE: You must light the pilot
before using the hand-held remote
control unit. See
Lighting Instruc-
tions
in your owner’s manual.
1. After lighting, let pilot flame burn for
about one minute. This is required be-
fore the burner will turn on. Turn con-
trol knob to the ON position. Adjust
flame adjustment knob anywhere be-
tween HI and LO. Slide the selector
switch to the REMOTE position (see
Figure 8, page 2).
Note:
The burner
may light if hand-held remote ON but-
ton was on when selector switch was
last turned off. You can now turn the
burners on and off with the hand-held
remote control unit.
IMPORTANT:
Do not leave the selec-
tor switch in the AUTO position on the
handset when the pilot is not lit. This
will shorten the battery life.
IMPORTANT:
Be sure to press the ON/
OFF buttons on the hand-held remote
control unit for up to 3 seconds to as-
sure proper operation.
On/Off Series
Press the control button on the hand-held
remote to turn burner on. Press the control
button again to turn burner off (see Figure 7,
page 2).
Continued
Front
Bac
k
Insulating
Washers
Remote
Receiver
Mounting
Clips
Front
Back
Wires
Nut
Nut
Screw
Figure 8 - Setting the Selector Switch,
Control Knob, and Flame Adjustment
Knob (Available on Some Models) for
Remote Operation
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
Selector Switch in Remote Position
Control Knob in On Position
Flame Adjustment Knob
(Available on Some Models)
107303-01
Rev. B
04/02
Figure 7 - On/Off Hand-Held Remote
Control Unit
Turns Burners On and Off
Thermostat Series
The transmitter can be operated using either
the manual ON/OFF mode or the auto (ther-
mostatic) mode, using the AUTO/ON/OFF
function select button. Depressing this but-
ton shows the current mode of operation. In
the auto mode the current temperature set-
ting is also displayed (see Figure 9).
Manual (ON/OFF) Mode
1. Press the function selection button to
select ON to turn on the fireplace.
2. Press the function selection button to
select OFF to turn off the fireplace.
Auto (Thermostatic) Mode
1. Press the function selection button to
AUTO to select this mode.
2. Set the desired comfort level heat set-
ting by pressing the TEMP up or down
button. The LED’s light up to show one
of the six settings. The unit automati-
cally cycles and turns the fireplace ON/
OFF until the desired setting is reached.
The lowest heat setting is the energy
save mode.
Note:
Do not leave the transmitter in the AUTO
mode unless temperature control is required.
Note:
Do not leave the transmitter in the AUTO
mode close to the fireplace. The radiant heat from
the fireplace will turn off the fireplace. Ideally,
place the transmitter in the center of the room
facing towards the fireplace.
Turns Burners
On or Off and
Allows You to
Choose the
Auto Setting
Shows
Temperature
Setting
Figure 9 - Thermostat Hand-Held Remote
Control Unit Selections
The Log Heater will Automatically Cycle
between Pilot and the Heat Setting that
has been Selected
Increases Room
Temperature in
AUTO Mode
Decreases
Room
Temperature
in AUTO
Mode
Note:
Do not hold the transmitter for a long
time. Body temperature will affect its op-
eration in the AUTO mode.
Safety Features
When away from home for an extended
period of time or as a child safety feature to
prevent accidental ignition of the fireplace,
the receiver ON/OFF/REMOTE switch
should be in the OFF position.
Auto Shutoff Feature
1. If the average room temperature exceeds
86 degrees Fahrenheit (30 degrees Centi-
grade), the remote control will perform a
safety override and shut the fireplace off.
2. The receiver continuously receives sig-
nals from the transmitter to control
room temperature. If the transmitter is
misplaced, obstructed, or for any rea-
son cannot transmit to the receiver, the
receiver will shut off the fireplace after
8 minutes.
Key Pad Lock Feature
This feature allows the user to lock/unlock
the keypad on the remote in the off or auto
mode to prevent inadvertent operation (i.e.
children operating the remote control, etc.).
1. To lock the keypad in the OFF mode, se-
lect the OFF function. Then press both the
function selection button and the TEMP
down button. The OFF light will start to
flash. Release both the buttons when the
flashing stops. The keypad is now locked.
If any key is pressed, the OFF light will
flash to indicate the locked status.
To unlock the keypad, press both the
function selection and the TEMP down
button simultaneously. The OFF light
will start to flash. Release both buttons
when the flashing stops. The keypad is
now unlocked.
2. To lock the keypad in the AUTO mode
select the AUTO function, then press
both the function selection button and
the TEMP down button. The AUTO
light will start to flash. Release both
buttons when the flashing stops. The
keypad is now locked. If any key is
pressed, the AUTO light will flash to
indicate the locked status.
To unlock the keypad, press both the
function selection and the TEMP down
button simultaneously. The AUTO light
will start to flash. Release both buttons
when the flashing stops. The keypad is
now unlocked.
Mode Indicator Feature
In the AUTO mode, the mode indicator
feature can be enabled to show that the
transmitter is operating after the fire is turned
off upon reaching the desired temperature.
To enable this feature, press both the TEMP
up and down buttons. The LED’s will start
to flash from top to bottom repeatedly and
then stop. Release both the buttons. To
disable this feature, press both the buttons
until the LED’s turn off and release.
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
107303 01
NOT A UPC
Note:
For customer service, call the manu-
facturer at 1-866-672-6040 or visit their
website at www.trackingtech.com.
-
1
-
2
Desa Tech CGHRC4 Owner's manual
- Category
- Fireplaces
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI