Sennheiser E 614 User manual

E 614
Sennheiser
Brand
Sennheiser
Model
E 614
Category
Microphones
Type
User manual

This manual is also suitable for

e 614
Instruction manual
e 614 | 2/7
Delivery includes
Delivery includes
• e 614
• MZQ 100 microphone clamp
• pouch
• quick guide
• safety guide
Product overview
2
1
1. Sound inlet basket
2. XLR-3 connector
e 614 | 3/7
Installation
Installation
Attaching the microphone
Screw the microphone clamp to a stand.
Place the microphone with its back end into the microphone clamp.
Orient the microphone together with the microphone clamp.
Connecting the microphone
Connect the XLR-3 socket of the microphone cable (optional accessories) to the XLR-3 socket of
the microphone.
Using the windshield
Place the MZW 64 (optional accessories) windshield over the microphone head.
e 614 | 4/7
Operation
Operation
Positioning the microphone: Drums / Percussions
Attention: When closing the hi-hat, a strong air current is created on the edge. If the microphone is
positioned too close to the edge, interfering noise due to the air current can occur.
It is vital to observe the following notes:
Position Resulting sound Commentary
A Natural, clear sound Position the microphone a few centimetres above the
outer edge of the hi-hat aiming down. If necessary,
remove unwanted low-frequency signal portions by
high pass filtering.
B More fundamental, little
overtones
A B
Positioning the monitor loudspeakers
To prevent feedback and crosstalk, postion your monitor loudspeakers in the angle area of the
highest cancellation of the microphone (approx. 135°).
135°
e 614 | 5/7
Cleaning and maintaining the e 614
Cleaning and maintaining the e 614
CAUTION
LIQUIDS CAN DAMAGE THE ELECTRONICS OF THE PRODUCT!
Liquids entering the housing of the product can cause a short-circuit and damage the electronics.
Keep all liquids away from the product.
Do not use any solvents or cleansing agents.
Disconnect the products from the power supply system and remove rechargeable batteries and
batteries before you begin cleaning.
Clean all products only with a soft, dry cloth.
e 614 | 6/7
Specifications
Specifications
Transducer principle pre-polarised condenser microphone
Frequency response 40 - 20,000 Hz
Pick-up pattern super-cardioid
Sensitivity (free field, no load) 3 mV/Pa
Nominal impedance (at 1 kHz) 50 Ω
Min. terminating impedance 1 kΩ
Max. sound pressure level (at 1 kHz) 139 dB
Equivalent noise level
weighted as per CCIR 468-3
24 dB(A)
35 dB
Phantom powering 12 - 48 V
Connector XLR-3
Dimensions ⌀ 20 x 100 mm
Weight 93 g
Polar pattern
30°
0°
180°
150°
120°
60°
90°
0
5
10
15
20
25
dB
30°
0°
180°
150°
120°
60°
90°
125 Hz
250 Hz
500 Hz
1,000 Hz
2,000 Hz
4,000 Hz
8,000 Hz
16,000 Hz
Frequency response
dBV
50
100
200
500
1,000
2,000
5,000
10,000
20,000
Hz
- 50
- 60
- 70
- 80
- 90
- 40
0°, 1 m
e 614 | 7/7
Overview of applications
Connector assignment
12
3
+
+
12
3
1
2
3
+ +
1
2
3
+
+
XLR
6.3 mm
XLR
XLR
XLR
BALANCED
Overview of applications
Primary application
Secondary application
•••• •
••
• •••
••
• ••
••
• • ••• •
•• • •• • • •
•• •
•• •
•• •
• • •
•• •
••
• •••
••
• • ••• •
••
••• •
• • • •• • • •
• •
• •
• •• ••
e 602 II
e 604
e 608
e 609
silver
e 614
e 835
e 845
e 865
e 901
e 902
e 904
e 906
e 908
e 914
e 935
e 945
e 965
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Sennheiser E 614 User manual

E 614
Sennheiser
Brand
Sennheiser
Model
E 614
Category
Microphones
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents