July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LED bulbs
E27
6W - 40W clear
6W - 40W frosted
Dimmable WarmGlow
E27
9W - 60W clear
9W - 60W frosted
Dimmable WarmGlow
E27
60W A60
Dimmable Warmglow
E27
6 - 40W CRI80 A60
Dimmable Warmglow
E27
9 - 60W CRI80 A60
Warmglow
1 2 3 4 5
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 1-3 87% ∼ 3%
1-3
98% ∼ 4% 1 - 3 90% ∼ 3% 1 -3 98% ∼ 8% 1 -3 94% ∼ 7%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 1-3 90% ∼ 3% 1-3 95% ∼ 3% 1 - 3 94% ∼ 3% 1 -3 98% ∼ 7% 1 -3 96% ∼ 5%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 1-3 93% ∼ 3% 1-3 94% ∼ 5% 1 - 3 96% ∼ 3% 1 -3 97% ∼ 19% 1 -3 94% ∼ 9%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 1-3 90% ∼ 3% 1-3 95% ∼ 3% 1 - 3 93% ∼ 3% 1 -3 99% ∼ 3% 1 -3 95% ∼ 3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 1-3 92% ∼ 3% 1-3 95% ∼ 3% 1 - 3 97% ∼ 3% 1 -3 97% ∼ 3% 1 -3 97% ∼ 3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 1-3 94% ∼ 8% 1-3 96% ∼ 5% 1 - 3 96% ∼ 3% 1 -3 98% ∼ 7% 1 -3 95% ∼ 6%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 1-3 86% ∼ 3% 1-3 89% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 83% ∼ 3% 1 -3 89% ∼ 3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire) T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. 1 -3 83% ∼ 3% 1 -3 89% ∼ 3%
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1-3 91% ∼ 4% 1-3 88% ∼ 5% 1 -3 88% ∼ 10% 1 -3 97% ∼ 6%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1-3 88% ∼ 3% 1-3 90% ∼ 4% 1 - 3 94% ∼ 4% N.A. N.A. 2- 3 93% ∼ 8%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 1-3 93% ∼ 3% 1-3 92% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 98% ∼ 3% 1 -3 94% ∼ 2%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 1-3 89% ∼ 3% 1-3 95% ∼ 3% 1 - 3 95% ∼ 3% N.A. N.A. N.A. N.A.
Eltako EVD61NPN-UC 400W 3-wire Push Module T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. 1 -3 98% ∼ 6% 1 -3 99% ∼ 3%
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1-3 88% ∼ 3% 1-3 90% ∼ 4% 1 - 3 94% ∼ 4% N.A. N.A. 2- 3 93% ∼ 8%
Feller| Schneider 40300 (SBD315) [RLC] 300W 1 - 3 92% ∼ 3% 1 -3 98% ∼ 3% 1 -3 94% ∼ 2%
Feller| Schneider 40420 (SBD420) [RLC] 420W 1 - 3 95% ∼ 3% N.A. N.A. N.A. N.A.
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1-3 93% ∼ 5% 1-3 88% ∼ 5% 1 -3 99% ∼ 19% N.A. N.A.
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 1-3 86% ∼ 3% 1-3 91% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 97% ∼ 31% 1 -3 95% ∼ 17%
Hager EVN 011 [RC] 300VA 1-3 98% ∼ 3% 1-3 93% ∼ 3% 1 -3 98% ∼ 8% 1 -3 99% ∼ 7%
Hager EVN 012 [RC] 300W 1-3 98% ∼ 3% 1-3 93% ∼ 3% 1 -3 98% ∼ 12% 1 -3 99% ∼ 6%
Hager EVN 004 [RL] 500VA 1-3 98% ∼ 3% 1-3 93% ∼ 3% 1 -3 99% ∼ 13% 1 -3 99% ∼ 6%
INSTA 1176 [RLC] 50 ∼ 420W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 1-3 93% ∼ 3% 1-3 96% ∼ 5% 1 - 3 92% ∼ 3% 1 - 3 98% ∼ 9% 1 - 3 96% ∼ 8%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 1-3 87% ∼ 7% 1-3 91% ∼ 7% 1 - 3 92% ∼ 7% 1 - 3 97% ∼ 4%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1-3 82% ∼ 4% 1-3 83% ∼ 5% N.A. N.A. 1 -3 89% ∼ 8%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. 2- 3 96% ∼ 8% 1 -3 96% ∼ 4%
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A. N.A. N.A. 2 - 3 96% ∼ 5%
Legrand 78401 [RLC] 40 ∼ 500W 1-3 96% ∼ 3% 1-3 93% ∼ 3% 1 -3 98% ∼ 7% 1 -3 97% ∼ 4%
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A. 2 - 3 97% ∼ 5%
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A. N.A. N.A. 3 98% ∼ 5% 2 - 3 97% ∼ 5%
Legrand 67083 [RLC] 3 ∼ 400W N.A. N.A. 1-3 90% ∼ 3% N.A. N.A. 1 - 2 89% ∼ 3%
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 1-3 95% ∼ 3% 1-3 95% ∼ 3% 1 - 3 94% ∼ 3% 2 - 3 99% ∼ 6% 1 -3 98% ∼ 6%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 1-3 88% ∼ 17% 1-3 95% ∼ 3% 1 - 3 97% ∼ 3% 1 -3 99% ∼ 3% 1 -3 96% ∼ 3%
Legrand L4402N [R] 60∼500W N.A. N.A. 2-3 83% ∼ 5% 2 - 3 97% ∼ 13% 2- 3 89% ∼ 6%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1-3 88% ∼ 3% 1-3 90% ∼ 4% 1 - 3 94% ∼ 4% N.A. N.A. 2- 3 93% ∼ 8%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 1-3 93% ∼ 3% 1-3 92% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 98% ∼ 3% 1 -3 94% ∼ 2%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 1-3 89% ∼ 3% 1-3 95% ∼ 3% 1 - 3 95% ∼ 3% N.A. N.A. N.A. N.A.
MK - Electric K1535 [R] 65 ∼ 450 W - Turn N.A. N.A. 1-3 80% ∼ 3% 1- 3 80% ∼ 3% 1 -3 99% ∼ 6% 1 -3 84% ∼ 5%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 1-3 85% ∼ 3% 1-3 90% ∼ 3% 1- 3 88% ∼ 3% 1 -3 97% ∼ 6% 1 -3 90% ∼ 5%
MK - Electric K4501 WHILV [RLC] 180W 1-3 88% ∼ 3% 1-3 83% ∼ 3% 1 -3 96% ∼ 7% 1 -3 90% ∼ 3%
MK - Electric K4500 WHILV [RLC] 400W 1-3 88% ∼ 3% 1-3 85% ∼ 3% 1 -3 95% ∼ 7% 1 -3 90% ∼ 3%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1-3 88% ∼ 4% 1-3 83% ∼ 5% 1- 3 98% ∼ 21% 1- 3 92% ∼ 3%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 1-3 86% ∼ 3% 1-3 89% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 83% ∼ 3% 1 -3 89% ∼ 3%
RELCO RP0977 [LED] 4-100W 1- 3 96% ∼ 4% 1- 2 99% ∼ 9%
RELCO RM0545 [LED] 4-100W 1- 3 98% ∼ 8% 1- 2 95% ∼ 4%
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 1-3 93% ∼ 3% 1-3 92% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 98% ∼ 3% 1 -3 94% ∼ 2%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 1-3 93% ∼ 3% 1-3 92% ∼ 3% 1 - 3 92% ∼ 3% 1 -3 98% ∼ 3% 1 -3 94% ∼ 2%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 1-3 88% ∼ 3% 1-3 90% ∼ 4% 1 - 3 94% ∼ 4% N.A. N.A. 2- 3 93% ∼ 8%
Schneider SBD315RC (SBD 315) [RC] 315W 1-3 93% ∼ 3% 1-3 90% ∼ 4% 1 - 3 92% ∼ 3% 1 -3 98% ∼ 3% 1 -3 94% ∼ 2%
VADSBO ED 350 [RC] 50 ∼350W 1-3 91% ∼ 5% 1-3 85% ∼ 5% 1 - 3 99% ∼ 25% 1 - 3 94% ∼ 8%
VADSBO DRS 315 [RC] 50 ∼315W N.A. N.A. 1-3 93% ∼ 3% <2 N.A. N.A. N.A. N.A.
VADSBO DU 250 [RC] 20 ∼250W 1-3 88% ∼ 3% <4 1-3 83% ∼ 3% <4 1 - 3 96% ∼ 6% 1 - 3 90% ∼ 3%
Varilight HQ3W [R] 60-400W 1-3 92% ∼ 3% 1-3 99% ∼ 3% 1 - 3 93% ∼ 3% 1 - 3 96% ∼ 4% 1 - 3 96% ∼ 3%
Varilight ICT401 M [RC] 20-400W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. 1 - 3 97% ∼ 3% 1 - 3 88% ∼ 2%
Vimar 20148 [RL] 500W N.A. N.A. N.A. N.A. 1- 3 96% ∼ 3% <2 1 - 3 97% ∼ 5% <3 1 - 3 96% ∼ 4% <2
Vimar 14153 [R] 1-3 98% ∼ 3% 1-3 98% ∼ 3% 2 - 3 98% ∼ 3% 1 - 3 95% ∼ 6%
Vimar 20160 [RC] N.A. N.A. 1-3 93% ∼ 3% <4 2 - 3 95% ∼ 3% <2 1 - 3 96% ∼ 3% <2
Vimar 20162 [RL] 40∼300W N.A. N.A. N.A. N.A. 1- 3 93% ∼ 3% <2 1 - 3 98% ∼ 7% <3 1 - 3 95% ∼ 9% <2
IKEA E0902 - Dim [R] 25∼150W 1-3 91% ∼ 1% 1-3 93% ∼ 1% 1- 3 93% ∼ 3% 1 - 3 97% ∼ 7% 1 - 3 96% ∼ 5%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LED bulbs
E27
13 - 75W CRI80 A60
Warmglow
E27
17 - 100W CRI80 A67
Warmglow
E27
6-40 W
Dimmable
E27
9.5-60 W
Dimmable
E27
11.5-75 W
Dimmable
6 7 8 9 10
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 1- 3 91% ∼ 10%
1 -3
83% ∼ 7% 1-3 94% ∼ 3% 1-3 95% ∼ 3% 1-3 90% ∼ 10% T.B.D.
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 1 - 3 76% ∼ 7% 1 -3 88% ∼ 8% 1-3 96% ∼ 3% 1-3 92% ∼ 11% 1-3 94% ∼ 12%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. 1 - 3 74% ∼ 8% <2 N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 1 - 3 77% ∼ 12% 1 - 3 88% ∼ 12% 1-3 98% ∼ 9% 1-3 94% ∼ 15% 1-3 92% ∼ 24%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 1 - 3 75% ∼ 3% 1 - 3 90% ∼ 4% N.A. N.A. 1-3 95% ∼ 3% 1-3 94% ∼ 3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 1 - 3 79% ∼ 2% 1 - 3 91% ∼ 3% 1-3 99% ∼ 3% 1-3 92% ∼ 3% 1-3 96% ∼ 3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 1 - 3 75% ∼ 7% 1 - 3 89% ∼ 7% 98% ∼ 5% 92% ∼ 4% 1-3 92% ∼ 10%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 1 -3 88% ∼ 3% 1 - 3 86% ∼ 3% 1-3 94% ∼ 3% 1-3 94% ∼ 3% 1-3 82% ∼ 3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire) T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. t.b.d. t.b.d. t.b.d.
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1 -3 95% ∼ 8% 1 -3 95% ∼ 8% 1-3 91% ∼ 13% 1-3 92% ∼ 19% 1-3 88% ∼ 23%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 77% ∼ 9% 1 - 3 84% ∼ 9% 3 91% ∼ 3% 1-3 91% ∼ 7% 1-3 88% ∼ 13%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 1 - 3 89% ∼ 3% 1 - 3 84% ∼ 3% 1-3 93% ∼ 3% 1-3 98% ∼ 3% 1-3 88% ∼ 3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 1 - 3 77% ∼ 5% 1 - 3 86% ∼ 5% 1-3 91% ∼ 3% 1-3 93% ∼ 3% 1-3 92% ∼ 3%
Eltako EVD61NPN-UC 400W 3-wire Push Module 1 - 3 99% ∼ 6% 1 - 3 99% ∼ 4% T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 77% ∼ 9% 1 - 3 84% ∼ 9% 3 91% ∼ 3% 1-3 91% ∼ 7% 1-3 88% ∼ 13%
Feller| Schneider 40300 (SBD315) [RLC] 300W 1 - 3 89% ∼ 3% 1 - 3 84% ∼ 3%
Feller| Schneider 40420 (SBD420) [RLC] 420W 1 - 3 77% ∼ 5% 1 - 3 86% ∼ 5%
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1 - 3 95% ∼ 14% 1 - 3 92% ∼ 12% 1-3 93% ∼ 15% 1-3 93% ∼ 13% 1-3 92% ∼ 20%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 1 - 3 69% ∼ 16% 1 - 3 84% ∼ 18% 1-3 94% ∼ 3% 1-3 99% ∼ 3% 1-3 90% ∼ 3%
Hager EVN 011 [RC] 300VA 1 - 3 96% ∼ 11% 1 - 3 97% ∼ 6% 1-3 97% ∼ 3% 1-3 97% ∼ 3% 1-3 97% ∼ 3%
Hager EVN 012 [RC] 300W 1 - 3 96% ∼ 11% 1 - 3 99% ∼ 9% 1-3 97% ∼ 3% 1-3 97% ∼ 3% 1-3 95% ∼ 3%
Hager EVN 004 [RL] 500VA 1 - 3 98%10% 1 - 3 99%10% 1-3 97% ∼ 3% 1-3 97% ∼ 3% 1-3 97% ∼ 5%
INSTA 1176 [RLC] 50 ∼ 420W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 1 - 3 90% ∼ 11% 1 - 3 85% ∼ 8% 1-3 92% ∼ 8% 1-3 93% ∼ 7% 1-3 90% ∼ 10%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 1 - 3 90% ∼ 6% 1 - 3 84% ∼ 4% 1-3 95% ∼ 3% 1-3 93% ∼ 3% 1-3 90% ∼ 28%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1 - 2 79% ∼ 15% 1 82% ∼ 16% 1-3 84% ∼ 12% 1-3 87% ∼ 20% 1-3 83% ∼ 25%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 1 - 3 96% ∼ 7% 1 - 3 84% ∼ 7% T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. t.b.d. t.b.d. t.b.d.
Legrand 774161 [RL] 40 ∼ 400 W - Turn 2 - 3 78% ∼ 5% 2- 3 92% ∼ 6% N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 78401 [RLC] 40 ∼ 500W 1 - 3 96% ∼ 7% 1 - 3 91% ∼ 6% 1-3 93% ∼ 3% 1-3 93% ∼ 3% 1-3 92% ∼ 5%
Legrand 67081 [RL] 40 ∼ 400 W - Turn 2 - 3 77% ∼ 5% 1 -3 94% ∼ 7% N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67082 [RL] 40 ∼ 600 W - Turn 2 - 3 75% ∼ 5% 2- 3 90% ∼ 6% N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67083 [RLC] 3 ∼ 400W 1 85% ∼ 4% 1 - 3 79% ∼ 4% N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 1 - 3 76% ∼ 5% 1 -3 91% ∼ 6% 98% ∼ 3% 92% ∼ 3% 1-3 92% ∼ 5%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 1 - 3 79% ∼ 3% 1 -3 93% ∼ 3% 96% ∼ 3% 97% ∼ 3% 1-3 94% ∼ 3%
Legrand L4402N [R] 60∼500W 2- 3 85% ∼ 13% 1 - 3 81% ∼ 11% N.A. N.A. 2-3 87% ∼ 11% 1-3 85% ∼ 17%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 77% ∼ 9% 1 - 3 84% ∼ 9% 3 91% ∼ 3% 1-3 91% ∼ 7% 1-3 88% ∼ 13%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 1 - 3 89% ∼ 3% 1 - 3 84% ∼ 3% 1-3 93% ∼ 3% 1-3 98% ∼ 3% 1-3 88% ∼ 3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 1 - 3 77% ∼ 5% 1 - 3 86% ∼ 5% 1-3 91% ∼ 3% 1-3 93% ∼ 3% 1-3 92% ∼ 3%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 1 - 3 66% ∼ 7% 1 - 3 75% ∼ 7% 1-3 82% ∼ 3% 1-3 84% ∼ 6% 1-3 82% ∼ 10%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 1 - 3 71% ∼ 6% 1 - 3 81% ∼ 6% 1-3 89% ∼ 3% 1-3 92% ∼ 3% 1-3 78% ∼ 8%
MK - Electric K4501 WHILV [RLC] 180W 1 - 3 84% ∼ 7% 1 - 3 87% ∼ 7% 1-3 87% ∼ 3% 1-3 88% ∼ 3% 1-3 78% ∼ 8%
MK - Electric K4500 WHILV [RLC] 400W 1 - 3 87% ∼ 7% 1 - 3 87% ∼ 7% 1-3 87% ∼ 3% 1-3 87% ∼ 3% 1-3 78% ∼ 8%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1 - 3 82% ∼ 5% 1 85% ∼ 5% 1-3 85% ∼ 12% 1-3 89% ∼ 27% 1-3 88% ∼ 28%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 1 -3 88% ∼ 3% 1 - 3 86% ∼ 3% 1-3 94% ∼ 3% 1-3 94% ∼ 3% 1-3 82% ∼ 3%
RELCO RP0977 [LED] 4-100W 1 - 2 99% ∼ 14% 1 98% ∼ 17%
RELCO RM0545 [LED] 4-100W 1 - 2 90% ∼ 6% 1 89% ∼ 6%
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 1 - 3 89% ∼ 3% 1 - 3 84% ∼ 3% 1-3 93% ∼ 3% 1-3 98% ∼ 3% 1-3 88% ∼ 3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 1 - 3 89% ∼ 3% 1 - 3 84% ∼ 3% 1-3 93% ∼ 3% 1-3 98% ∼ 3% 1-3 88% ∼ 3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 1 - 3 77% ∼ 9% 1 - 3 84% ∼ 9% 3 91% ∼ 3% 1-3 91% ∼ 7% 1-3 88% ∼ 13%
Schneider SBD315RC (SBD 315) [RC] 315W 1 - 3 89% ∼ 3% 1 - 3 84% ∼ 3% 1-3 93% ∼ 3% 1-3 98% ∼ 3% 1-3 88% ∼ 3%
VADSBO ED 350 [RC] 50 ∼350W 1- 3 87% ∼ 13% 1 -3 82% ∼ 11% 1-3 89% ∼ 16% 1-3 85% ∼ 11% 1-3 85% ∼ 17%
VADSBO DRS 315 [RC] 50 ∼315W 1- 3 92% ∼ 9% <4 1 -3 94% ∼ 8% <4 1-3 92% ∼ 3% 1-3 92% ∼ 3% 1-3 90% ∼ 7%
VADSBO DU 250 [RC] 20 ∼250W 1- 3 85% ∼ 5% <4 1 -3 79% ∼ 4% <4 1-3 87% ∼ 3% 1-3 83% ∼ 3% 1-3 80% ∼ 3%
Varilight HQ3W [R] 60-400W 1 - 3 74% ∼ 5% 1 -3 87% ∼ 5% 1-3 95% ∼ 3% 1-3 95% ∼ 3% 1-3 94% ∼ 3%
Varilight ICT401 M [RC] 20-400W 1- 3 83% ∼ 7% 1 -3 91% ∼ 3% t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Vimar 20148 [RL] 500W 1 - 2 78% ∼ 5% <4 1 -3 89% ∼ 6% <4 N.A. N.A. 1-3 94% ∼ 3% 1-3 94% ∼ 7%
Vimar 14153 [R] 1- 3 97% ∼ 3% 1 -3 98% ∼ 3% 1-3 99% ∼ 3% 1-3 99% ∼ 3% 1-3 97% ∼ 3%
Vimar 20160 [RC] 1- 3 96% ∼ 4% <4 1 -3 88% ∼ 4% <4 N.A. N.A. 1-3 92% ∼ 3% 1-3 90% ∼ 3%
Vimar 20162 [RL] 40∼300W 1 - 2 75% ∼ 5% <4 1 -3 87% ∼ 5% <4 1-3 95% ∼ 5% 1-3 88% ∼ 3% 1-3 88% ∼ 3%
IKEA E0902 - Dim [R] 25∼150W 1 - 3 79% ∼ 7% 1 -2 90% ∼ 8% 1-3 96% ∼ 2% 1-3 95% ∼ 10% 1-3 92% ∼ 12% t.b.d.
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LED bulbs
E27
16-100 W
Dimmable
E27
A60 4.5W - 40W
WarmGlow
E27
A60 7.5W - 60W
WarmGlow
11 12 13
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 1-3 91%~9%
1-3
87%~3% 1-3 98%~4%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn N.A. N.A. 1-3 90%~3% 1-3 95%~3%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 1-3 94%~25% 1-3 93%~3% 1-3 94%~5%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 1-3 94%~3% 1-3 90%~3% 1-3 95%~3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 1-3 94%~3% 1-3 92%~3% 1-3 95%~3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 1-3 93%~9% 1-3 94%~8% 1-3 96%~5%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 1-3 90%~3% 1-3 86%~3% 1-3 89%~3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire) t.b.d. t.b.d. t.b.d. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1-3 91%~25% 1-3 91%~4% 1-3 88%~5%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1-3 90%~13% 1-3 88%~3% 1-3 90%~4%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 1-3 90%~3% 1-3 93%~3% 1-3 92%~3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 1-3 94%~3% 1-3 89%~3% 1-3 95%~3%
Eltako EVD61NPN-UC 400W 3-wire Push Module T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1-3 90%~13% 1-3 88%~3% 1-3 90%~4%
Feller| Schneider 40300 (SBD315) [RLC] 300W
Feller| Schneider 40420 (SBD420) [RLC] 420W
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1-3 93%~19% 1-3 93%~5% 1-3 88%~5%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 1-3 91%~3% 1-3 86%~3% 1-3 91%~3%
Hager EVN 011 [RC] 300VA 1-3 96%~4% 1-3 98%~3% 1-3 93%~3%
Hager EVN 012 [RC] 300W 1-3 95%~4% 1-3 98%~3% 1-3 93%~3%
Hager EVN 004 [RL] 500VA 1-3 98%~4% 1-3 98%~3% 1-3 93%~3%
INSTA 1176 [RLC] 50 ∼ 420W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 1-3 91%~11% 1-3 93%~3% 1-3 96%~5%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 1-3 91%~26% 1-3 87%~7% 1-3 91%~7%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1-3 85%~23% 1-3 82%~4% 1-3 83%~5%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer t.b.d. t.b.d. t.b.d. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A.
Legrand 78401 [RLC] 40 ∼ 500W 1-3 94%~5% 1-3 96%~3% 1-3 93%~3%
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67083 [RLC] 3 ∼ 400W N.A. N.A. N.A. N.A. 1-3 90%~3%
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 1-3 92%~5% 1-3 95%~3% 1-3 95%~3%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 1-3 94%~3% 1-3 88%~17% 1-3 95%~3%
Legrand L4402N [R] 60∼500W 1-3 85%~16% N.A. N.A. 2-3 83%~5%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1-3 90%~13% 1-3 88%~3% 1-3 90%~4%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 1-3 90%~3% 1-3 93%~3% 1-3 92%~3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 1-3 94%~3% 1-3 89%~3% 1-3 95%~3%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 1-3 83%~9% N.A. N.A. 1-3 80%~3%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 1-3 88%~8% 1-3 85%~3% 1-3 90%~3%
MK - Electric K4501 WHILV [RLC] 180W 1-3 88%~8% 1-3 88%~3% 1-3 83%~3%
MK - Electric K4500 WHILV [RLC] 400W 1-3 88%~8% 1-3 88%~3% 1-3 85%~3%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1-3 88%~28% 1-3 88%~4% 1-3 83%~5%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 1-3 90%~3% 1-3 86%~3% 1-3 89%~3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 1-3 90%~3% 1-3 93%~3% 1-3 92%~3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 1-3 90%~3% 1-3 93%~3% 1-3 92%~3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 1-3 90%~13% 1-3 88%~3% 1-3 90%~4%
Schneider SBD315RC (SBD 315) [RC] 315W 1-3 90%~3% 1-3 93%~3% 1-3 90%~4%
VADSBO ED 350 [RC] 50 ∼350W 1-3 83%~15% 1-3 91%~5% 1-3 85%~5%
VADSBO DRS 315 [RC] 50 ∼315W 1-3 91%~6% N.A. N.A. 1-3 93%~3% <2
VADSBO DU 250 [RC] 20 ∼250W 1-3 80%~3% 1-3 88%~3% <4 1-3 83%~3% <4
Varilight HQ3W [R] 60-400W 1-3 93%~3% 1-3 92%~3% 1-3 99%~3%
Varilight ICT401 M [RC] 20-400W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Vimar 20148 [RL] 500W 1-3 94%~6% N.A. N.A. N.A. N.A.
Vimar 14153 [R] 1-3 98%~3% 1-3 98%~3% 1-3 98%~3%
Vimar 20160 [RC] 1-3 91%~3% N.A. N.A. 1-3 93%~3% <4
Vimar 20162 [RL] 40∼300W 1-3 91%~3% N.A. N.A. N.A. N.A.
IKEA E0902 - Dim [R] 25∼150W 1-2 94%~9% 1-3 91%~1% 1-3 93%~1%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
Image missingImage missing
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
Classic LED bulbs
E27
A60 5W - 40W
Dimmable
E27
A60 7W - 60W
Dimmable
E27
A60 4.5W - 40W
Dimmable
14 15 16
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 1 - 3
1 - 3
1 - 3 93%~5%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 1 - 3 1 - 3 1 - 3 92%~5%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 1 - 3 1 - 3 1 - 3 90%~11%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 1 - 3 1 - 3 1 - 3 91%~3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 1 - 3 1 - 3 1 - 3 91%~3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 1 - 3 1 - 3 1 - 3 95%~3%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 1 - 3 1 - 3 1 - 3 91%~3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire)
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1 - 3 94%~3% 1 - 5 94%~3% 1 - 3 96%~3%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 1 - 3 2-3 94%~3%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 1 - 3 1 - 3 2-3 91%~3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 2 - 3 1 - 3 2-3 96%~3%
Eltako EVD61NPN-UC 400W 3-wire Push Module 1 - 3 92%~3% 1 - 5 98%~3% 1-3 99%~3%
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2 - 3 1 - 3 2-3 94%~3%
Feller| Schneider 40300 (SBD315) [RLC] 300W
Feller| Schneider 40420 (SBD420) [RLC] 420W
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1 - 3 90%~9% 1 - 5 92%~9% 1 - 3 95%~13%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 1 - 3 1 - 3 1 - 3 90%~3%
Hager EVN 011 [RC] 300VA 1 - 3 97%~3% 1 - 5 98%~3% 1 - 3 99%~3%
Hager EVN 012 [RC] 300W 1 - 3 97%~3% 1 - 5 97%~3% 1 - 3 99%~4%
Hager EVN 004 [RL] 500VA 1 - 3 97%~3% 1 - 5 97%~3% 1 - 3 98%~5%
INSTA 1176 [RLC] 50 ∼ 420W
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 1 - 3 1 - 3 1 - 3 89%~4%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 1 - 3 1 - 3 1 - 3 89%~3%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1 - 3 85%~10% N.A. N.A. 1 - 3 88%~3%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 2 - 3 98%~3% N.A. N.A. 1-3 91%~3%
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. 3 91%~3%
Legrand 78401 [RLC] 40 ∼ 500W 1 - 3 95%~3% 1 - 5 94%~3% 1 - 3 96%~3%
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. 3 92%~3%
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A. 3 93%~3%
Legrand 67083 [RLC] 3 ∼ 400W 1 - 3 86%~3% N.A. N.A. 1 - 3 88%~3%
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 1 - 3 1 - 3 1 - 3 94%~3%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 1 - 3 1 - 3 1 - 3 96%~3%
Legrand L4402N [R] 60∼500W 2 - 3 88%~3% 1 - 5 86%~3% 3 87%~4%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 1 - 3 2-3 94%~3%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 1 - 3 1 - 3 2-3 91%~3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 2 - 3 1 - 3 2-3 96%~3%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 1 - 3 1 - 3 1 - 3 84%~3%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 1 - 3 1 - 3 2-3 84%~3%
MK - Electric K4501 WHILV [RLC] 180W 1 - 3 87%~3% 1 - 5 88%~3% 2-3 88%~3%
MK - Electric K4500 WHILV [RLC] 400W 1 - 3 88%~3% 1 - 5 88%~3% 2-3 89%~3%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1-3 87%~3% 1 - 3 86%~3% 1-3 88%~3%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 1 - 3 1 - 3 1 - 3 91%~3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 1 - 3 1 - 3 2-3 91%~3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 1 - 3 1 - 3 2-3 91%~3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 1 - 3 1 - 3 2-3 94%~3%
Schneider SBD315RC (SBD 315) [RC] 315W 1 - 3 1 - 3 2-3 91%~3%
VADSBO ED 350 [RC] 50 ∼350W 1 - 3 90%~8% 1 - 5 87%~6% 1 - 3 93%~13%
VADSBO DRS 315 [RC] 50 ∼315W N.A. N.A. 1 - 5 93%~3% N.A. N.A.
VADSBO DU 250 [RC] 20 ∼250W 1 - 3 85%~3% < 4 1 - 5 82%~3% 1-3 91%~3% < 3
Varilight HQ3W [R] 60-400W 1 - 3 2 - 3 2-3 93%~3%
Varilight ICT401 M [RC] 20-400W 1 - 3 81%~3% 1 - 5 91%~3% 1-3 82%~3%
Vimar 20148 [RL] 500W 2 - 3 < 3 1 - 3 1-3 90%~3%
Vimar 14153 [R] 2 - 3 98%~3% 2 - 3 99%~3% 1-3 99%~3%
Vimar 20160 [RC] 1 - 3 92%~3% < 2 1 - 5 92%~3% 1-3 93%~3% < 2
Vimar 20162 [RL] 40∼300W 2 - 3 < 3 1 - 3 1-3 92%~3%
IKEA E0902 - Dim [R] 25∼150W 1 - 3 1 - 3 1-3 94%~3%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
Image missing
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
Classic LED bulbs
E27
ST64 7W - 60W / ST64 gold dim - 50W / G93 clear -60W
G120 gold dim - 50W
Dimmable
E27
A60 7.5W - 48W Gold / A60 7.5W - 60W
Dimmable
E27
48W A60 gold / 50W ST64 gold / 50W G120 gold
40W A60 CL / 60W A60 CL / 40W A60 WGD
60W A60 WGD / 60W ST64 WGD / 60W ST64 CL
17 18 19
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 1 - 3 93%'3% 1- 3 89%'3% 1 -3 98%~3%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 1 - 3 94%'3% 1 92%'3% 2-3 97%~3%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 1 - 3 97%'3% 1 - 3 93%'3% 1 -3 98%~8%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 1 - 3 94%'3% 1 - 3 92%'3% 1 -3 98%~3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 1 - 3 96%'3% 1 - 3 93%'3% 1 -3 97%~3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 1 - 3 95%'3% 1 - 3 93%'3% 1 -3 99%~3%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 1 - 3 91%'3% 1 - 3 88%'3% 1 -3 97%~3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire)
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1 - 3 95%'3% 1 - 3 97%'3%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 94%'6% 1 - 3 90%'4% 2-3 99%~3%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 1 - 3 83%'3% 1 - 3 90%'3% 2-3 98%~3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 3 99%'3% 2 - 3 93%'3% N.A. N.A.
Eltako EVD61NPN-UC 400W 3-wire Push Module 1 - 3 99%'3% 1 - 3 99%'3%
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 94%'6% 1 - 3 90%'4% 2-3 99%~3%
Feller| Schneider 40300 (SBD315) [RLC] 300W 2-3 98%~3%
Feller| Schneider 40420 (SBD420) [RLC] 420W N.A. N.A.
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1 - 3 95%'11% 1 - 3 96%'13%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 1 - 3 93%'3% 1 - 3 89%'3%
Hager EVN 011 [RC] 300VA 1 - 3 96%'3% 1 - 3 99%'3%
Hager EVN 012 [RC] 300W 1 - 3 98%'3% 1 - 3 98%'4%
Hager EVN 004 [RL] 500VA 1 - 3 98%'4% 1 - 3 99%'4%
INSTA 1176 [RLC] 50 ∼ 420W
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 1 - 3 93%'6% 1- 3 90%'4% 1 -3 98%~3%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 1 - 3 95%'10% 1 - 3 90%'3% 1 -3 97%~3%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1 - 3 86%'3% 1 - 3 86%'11%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 1 - 3 80%'3% 1 - 3 93%'3%
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. 2- 3 93%'3% 2-3 98%~3%
Legrand 78401 [RLC] 40 ∼ 500W 1 - 3 95%'3% 1 - 3 96%'3%
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A. 2-3 97%~3%
Legrand 67083 [RLC] 3 ∼ 400W 1 - 2 87%'5% 1- 3 87%'3%
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 1 - 3 95%'3% 1- 3 93%'3% 1 -3 97%~3%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 1 - 3 98%'3% 1- 3 95%'3% 1 -3 97%~3%
Legrand L4402N [R] 60∼500W 2 - 3 87%'5% 1- 3 87%'5%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 1 - 3 94%'6% 1 - 3 90%'4% 2-3 99%~3%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 1 - 3 83%'3% 1 - 3 90%'3% 2-3 98%~3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 3 99%'3% 2 - 3 93%'3% N.A. N.A.
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 1 - 3 84%'3% 1 - 3 81%'3% 2-3 93%~3%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 1 - 3 87%'3% 1 - 3 86%'3% 1-3 98%~3%
MK - Electric K4501 WHILV [RLC] 180W 1 - 3 91%'9% 1 - 3 88%'3%
MK - Electric K4500 WHILV [RLC] 400W 1 - 3 91%'9% 1 - 3 88%'3%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1 - 3 87%'3% 1 - 3 87%'3%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 1 - 3 91%'3% 1 - 3 88%'3% 1 -3 97%~3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 1 - 3 83%'3% 1 - 3 90%'3% 2-3 98%~3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 1 - 3 83%'3% 1 - 3 90%'3% 2-3 98%~3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 1 - 3 94%'6% 1 - 3 90%'4% 2-3 99%~3%
Schneider SBD315RC (SBD 315) [RC] 315W 1 - 3 83%'3% 1 - 3 90%'3% 2-3 98%~3%
VADSBO ED 350 [RC] 50 ∼350W 1 - 3 91%'9% 1 - 3 93%'13%
VADSBO DRS 315 [RC] 50 ∼315W N.A. N.A. 1- 3 95%'3%
VADSBO DU 250 [RC] 20 ∼250W 1 - 3 87%'3% 1- 3 88%'3%
Varilight HQ3W [R] 60-400W 1 - 3 93%'3% 1- 3 91%'3% 2 -3 97%~3%
Varilight ICT401 M [RC] 20-400W 1 - 3 87%'3% 1- 3 87%'3%
Vimar 20148 [RL] 500W 1 - 3 95%'3% <2 1 - 3 92%'3% 1 -3 98%~3%
Vimar 14153 [R] 1 - 3 98%'3% 1 - 3 98%'3%
Vimar 20160 [RC] 1 - 3 92%'3% 1 - 3 94%'3%
Vimar 20162 [RL] 40∼300W 1 - 3 97%'3% <2 1 - 3 91%'3% 1 -3 98%~3%
IKEA E0902 - Dim [R] 25∼150W 1 - 3 97%'3% 1 - 3 93%'3% 1 -3 98%~3%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Images missing Images missing
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LED candle / LED lustre
E14/E27
4 - 25W
Dimmable WarmGlow
E14 / E27
6 - 40W
Dimmable WarmGlow
E14
60W B40 / 40W P48
Dimmable Wamglow
E14
4 - 15W
Flame
20 21 22 23
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 2-18 96% ∼ 3%
2-12
93% ∼ 3% 2-12 90% ∼ 3% 2 - 20 89% ∼ 16%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 2-20 89% ∼ 3% 2-13 89% ∼ 3% 2 - 20 93% ∼ 12%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 2-20 92% ∼ 3% 2-13 92% ∼ 3% 2 - 20 94% ∼ 14%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 2-25 91% ∼ 3% 2-17 91% ∼ 3% 2 - 20 93% ∼ 3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 2-30 88% ∼ 3% 2-20 93% ∼ 3% 2-15 92% ∼ 3% 2 - 20 94% ∼ 3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 2-21 94% ∼ 3% 2-14 91% ∼ 3% 2-14 91% ∼ 3% 2 - 20 91% ∼ 15%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 2-20 84% ∼ 3% 2-17 83% ∼ 3% 2-15 88% ∼ 3% 2 - 20 88% ∼ 3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire) T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 2-20 88% ∼ 7% <4 2-17 88% ∼ 5% < 6 2 - 20 96% ∼ 14%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2-20 95% ∼ 3% 2-13 92% ∼ 3% 2-13 90% ∼ 3% 2 - 20 89% ∼ 21%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 2-15 88% ∼ 3% 2-11 87% ∼ 0% 2-11 90% ∼ 3% 2 - 16 88% ∼ 3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 2-20 91% ∼ 3% 2-14 90% ∼ 3% tbd tbd tbd 2 - 20 94% ∼ 5%
Eltako EVD61NPN-UC 400W 3-wire Push Module T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. 2 - 20 99% ∼ 5%
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2-20 95% ∼ 3% 2-13 92% ∼ 3% 2-13 90% ∼ 3% 2 - 20 89% ∼ 21%
Feller| Schneider 40300 (SBD315) [RLC] 300W 2-11 90% ∼ 3%
Feller| Schneider 40420 (SBD420) [RLC] 420W tbd tbd tbd
GIRA 1176-00/01 [RLC] 50 ∼ 420W 2-20 95% ∼ 7% <7 2-14 95% ∼ 5% < 9 2 - 20 98% ∼ 29%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 2-25 94% ∼ 3% 2-17 92% ∼ 3% 2 - 20 89% ∼ 7%
Hager EVN 011 [RC] 300VA 95% ∼ 4% <7 2-10 96% ∼ 3% < 10 2 - 15 89% ∼ 7%
Hager EVN 012 [RC] 300W 95% ∼ 4% <7 2-10 95% ∼ 3% < 10 2 - 15 97% ∼ 19%
Hager EVN 004 [RL] 500VA 95% ∼ 7% <7 2-17 96% ∼ 4% < 11 2 - 20 98% ∼ 20%
INSTA 1176 [RLC] 50 ∼ 420W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 2-26 89% ∼ 3% 2-18 89% ∼ 3% 2-10 89% ∼ 3% 2 - 20 91% ∼ 19%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 2-25 93% ∼ 4% 2-17 92% ∼ 3% 2-15 90% ∼ 3% 2 - 20 90% ∼ 5%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 78% ∼ 7% <6 2-4 77% ∼ 4% < 5 2 - 6 84% ∼ 29%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. N.A. N.A.
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 78401 [RLC] 40 ∼ 500W 2-20 95% ∼ 4% <7 2-13 93% ∼ 4% < 9 2 - 20 96% ∼ 14%
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67083 [RLC] 3 ∼ 400W N.A. N.A. N.A. N.A. N.A. N.A.
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) N.A. N.A. N.A. N.A. 2 - 20 94% ∼ 9%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 2-15 94% ∼ 3% 2-10 91% ∼ 3% 2-10 95% ∼ 3% 2 - 20 94% ∼ 9%
Legrand L4402N [R] 60∼500W 79% ∼ 4% 8-17 79% ∼ 4% 5 - 20 84% ∼ 21%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2-20 95% ∼ 3% 2-13 92% ∼ 3% 2-13 90% ∼ 3% 2 - 20 89% ∼ 21%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 2-15 88% ∼ 3% 2-11 87% ∼ 3% 2-11 90% ∼ 3% 2 - 16 88% ∼ 3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 2-20 91% ∼ 3% 2-14 90% ∼ 3% tbd tbd tbd 2 - 20 94% ∼ 5%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 2-23 79% ∼ 3% 2-15 77% ∼ 3% 2-15 80% ∼ 3% 2 - 20 80% ∼ 11%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 2-25 88% ∼ 3% 2-17 87% ∼ 3% 3 - 20 85% ∼ 11%
MK - Electric K4501 WHILV [RLC] 180W 83% ∼ 3% 2-7 82% ∼ 3% 2 - 10 86% ∼ 10%
MK - Electric K4500 WHILV [RLC] 400W 83% ∼ 3% N.A. N.A. 2 - 20 87% ∼ 10%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 82% ∼ 7% 2-4 82% ∼ 5% 2 - 6 86% ∼ 3%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 2-20 84% ∼ 3% 2-17 83% ∼ 3% 2-15 88% ∼ 3% 2 - 20 88% ∼ 3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 2-15 88% ∼ 3% 2-11 87% ∼ 3% 2-11 90% ∼ 3% 2 - 16 88% ∼ 3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 2-15 88% ∼ 3% 2-11 87% ∼ 3% 2-11 90% ∼ 3% 2 - 16 88% ∼ 3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 2-20 95% ∼ 3% 2-13 92% ∼ 3% 2-13 90% ∼ 3% 2 - 20 89% ∼ 21%
Schneider SBD315RC (SBD 315) [RC] 315W 2-15 88% ∼ 3% 2-11 87% ∼ 3% 2-11 90% ∼ 3% 2 - 16 88% ∼ 3%
VADSBO ED 350 [RC] 50 ∼350W 2-18 88% ∼ 7% 2-12 84% ∼ 4% 2 - 20 89% ∼ 25%
VADSBO DRS 315 [RC] 50 ∼315W 4-16 89% ∼ 4% 5-11 91% ∼ 4% < 12 10 - 16 93% ∼ 15%
VADSBO DU 250 [RC] 20 ∼250W 2-13 86% ∼ 3% 2-8 79% ∼ 3% < 8 2 - 13 84% ∼ 3%
Varilight HQ3W [R] 60-400W 2-20 91% ∼ 3% 2-13 90% ∼ 3% 2-13 90% ∼ 3% 2 - 20 92% ∼ 3%
Varilight ICT401 M [RC] 20-400W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. 2 - 20 84% ∼ 9%
Vimar 20148 [RL] 500W 6-25 90% ∼ 3% <6 4-17 92% ∼ 3% <4 2 - 20 91% ∼ 8%
Vimar 14153 [R] 2-20 99% ∼ 3% 2-17 96% ∼ 3% < 7 2 - 20 99% ∼ 3%
Vimar 20160 [RC] 89% ∼ 3% 2-10 89% ∼ 3% < 11 3 - 20 93% ∼ 3%
Vimar 20162 [RL] 40∼300W 6-15 92% ∼ 3% <6 4-10 86% ∼ 3% <4 2 - 20 89% ∼ 11%
IKEA E0902 - Dim [R] 25∼150W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. 2 - 8 92% ∼ 12%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
Image missing
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LED candle / LED lustre
E14 / E27
B35 3 - 25W clear
P45 3- 25W clear
E14 / E27
B35 4.5 - 40W clear
P45 4.5 - 40W clear
E14
B38 3W
Dimmable
B35 25W CL
B35 40W CL
B35 35W Gold
24 25 26 27
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 2 - 24 93% ∼ 3%
2 - 16
91% ∼ 3% 2 - 24 93% ∼ 3% 2 - 8 99% ∼ 3%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 2 - 27 95% ∼ 3% 2 - 18 95% ∼ 3% 2 - 27 95% ∼ 3% 2 - 8 99% ∼ 3%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 2 - 20 94% ∼ 11% 2 - 18 95% ∼ 3% 2 - 20 94% ∼ 11% 2 - 8 99% ∼ 12%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 5 - 20 95% ∼ 3% 2 - 22 95% ∼ 3% 5 - 20 95% ∼ 3% 2 - 8 99% ∼ 3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 2 - 20 95% ∼ 3% 2 - 18 92% ∼ 3% 2 - 20 95% ∼ 3% 3 - 8 99% ∼ 3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 2 - 20 95% ∼ 3% 2 - 19 94% ∼ 3% 2 - 20 95% ∼ 3% 2 - 8 99% ∼ 3%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 2 - 20 90% ∼ 3% 2 - 20 90% ∼ 3% 2 - 20 90% ∼ 3% 2 - 6 99% ∼ 3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire)
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 2 - 20 96% ∼ 3% 2 - 20 94% ∼ 3% 2 - 20 96% ∼ 3%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2 - 27 94% ∼ 3% 2 - 18 92% ∼ 3% 2 - 27 94% ∼ 3% 2 - 8 99% ∼ 3%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 2 - 21 93% ∼ 3% 2 - 14 93% ∼ 3% 2 - 21 93% ∼ 3% 3 - 8 99% ∼ 3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 7 - 28 96% ∼ 3% 3 - 19 95% ∼ 3% 7 - 28 96% ∼ 3% 3 - 8 99% ∼ 3%
Eltako EVD61NPN-UC 400W 3-wire Push Module 2 - 20 99% ∼ 3% 2 - 18 98% ∼ 3% 2 - 20 99% ∼ 3%
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2 - 27 94% ∼ 3% 2 - 18 92% ∼ 3% 2 - 27 94% ∼ 3% 2 - 8 99% ∼ 3%
Feller| Schneider 40300 (SBD315) [RLC] 300W 3 - 8 99% ∼ 3%
Feller| Schneider 40420 (SBD420) [RLC] 420W 3 - 8 99% ∼ 3%
GIRA 1176-00/01 [RLC] 50 ∼ 420W 2 - 20 95% ∼ 13% 2 - 19 95% ∼ 10% 2 - 20 95% ∼ 13%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 2 - 30 91% ∼ 3% 2 - 22 92% ∼ 3% 2 - 30 91% ∼ 3% 2 - 8 99% ∼ 19%
Hager EVN 011 [RC] 300VA 2 - 20 99% ∼ 3% 2 - 13 98% ∼ 3% 2 - 20 99% ∼ 3%
Hager EVN 012 [RC] 300W 2 - 20 99% ∼ 4% 2 - 13 98% ∼ 3% 2 - 20 99% ∼ 4%
Hager EVN 004 [RL] 500VA 2 - 20 99% ∼ 5% 2 - 20 97% ∼ 3% 2 - 20 99% ∼ 5%
INSTA 1176 [RLC] 50 ∼ 420W
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 3 - 30 94% ∼ 3% 2 - 23 92% ∼ 3% 3 - 30 94% ∼ 3% 2 - 8 99% ∼ 3%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 2 - 30 91% ∼ 3% 2 - 22 90% ∼ 3% 2 - 30 91% ∼ 3% 2 - 8 99% ∼ 3%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 2 - 8 85% ∼ 3% 2 - 13 81% ∼ 12% 2 - 8 85% ∼ 3%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 2 - 20 90% ∼ 3% 2 - 13 88% ∼ 3% 2 - 20 90% ∼ 3%
Legrand 774161 [RL] 40 ∼ 400 W - Turn 5 - 27 95% ∼ 3% 5 - 18 95% ∼ 3% 5 - 27 95% ∼ 3% 3 - 8 99% ∼ 3%
Legrand 78401 [RLC] 40 ∼ 500W 2 - 20 97% ∼ 3% 2 - 18 95% ∼ 3% 2 - 20 97% ∼ 3%
Legrand 67081 [RL] 40 ∼ 400 W - Turn 5 - 20 96% ∼ 3% 3 - 13 86% ∼ 3% 5 - 20 96% ∼ 3% 3 - 8 99% ∼ 3%
Legrand 67082 [RL] 40 ∼ 600 W - Turn 4 - 30 97% ∼ 3% 4 - 27 96% ∼ 3% 4 - 30 97% ∼ 3% 3 - 8 99% ∼ 3%
Legrand 67083 [RLC] 3 ∼ 400W 2 - 5 87% ∼ 3% 2 - 18 86% ∼ 3% 2 - 5 87% ∼ 3%
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 2 - 27 90% ∼ 3% 2 - 18 95% ∼ 3% 2 - 27 90% ∼ 3% 2 - 8 99% ∼ 3%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 2 - 20 96% ∼ 3% 2 - 13 98% ∼ 3% 2 - 20 96% ∼ 3% 2 - 8 99% ∼ 3%
Legrand L4402N [R] 60∼500W 8 - 20 96% ∼ 3% 5 - 20 85% ∼ 4% 8 - 20 96% ∼ 3%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2 - 27 94% ∼ 3% 2 - 18 92% ∼ 3% 2 - 27 94% ∼ 3% 2 - 8 99% ∼ 3%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 2 - 21 93% ∼ 3% 2 - 14 93% ∼ 3% 2 - 21 93% ∼ 3% 3 - 8 99% ∼ 3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 7 - 28 96% ∼ 3% 3 - 19 95% ∼ 3% 7 - 28 96% ∼ 3% 3 - 8 99% ∼ 3%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 2 - 30 83% ∼ 3% 2 - 20 82% ∼ 3% 2 - 30 83% ∼ 3% 3 - 8 99% ∼ 3%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 2 - 30 88% ∼ 3% 2 - 22 88% ∼ 3% 2 - 30 88% ∼ 3% 3 - 8 99% ∼ 3%
MK - Electric K4501 WHILV [RLC] 180W 2 - 15 88% ∼ 3% 2 - 10 88% ∼ 3% 2 - 15 88% ∼ 3%
MK - Electric K4500 WHILV [RLC] 400W 2 - 20 87% ∼ 3% 2 - 18 87% ∼ 3% 2 - 20 87% ∼ 3%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 2 - 8 86% ∼ 3% 2 - 5 86% ∼ 3% 2 - 8 86% ∼ 3%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 2 - 20 90% ∼ 3% 2 - 20 90% ∼ 3% 2 - 20 90% ∼ 3% 2 - 6 99% ∼ 3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 2 - 21 93% ∼ 3% 2 - 14 93% ∼ 3% 2 - 21 93% ∼ 3% 3 - 8 99% ∼ 3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 2 - 21 93% ∼ 3% 2 - 14 93% ∼ 3% 2 - 21 93% ∼ 3% 3 - 8 99% ∼ 3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 2 - 27 94% ∼ 3% 2 - 18 92% ∼ 3% 2 - 27 94% ∼ 3% 2 - 8 99% ∼ 3%
Schneider SBD315RC (SBD 315) [RC] 315W 2 - 21 93% ∼ 3% 2 - 14 93% ∼ 3% 2 - 21 93% ∼ 3% 3 - 8 99% ∼ 3%
VADSBO ED 350 [RC] 50 ∼350W 2 - 21 93% ∼ 10% 2 - 16 91% ∼ 7% 2 - 21 93% ∼ 10%
VADSBO DRS 315 [RC] 50 ∼315W N.A. N.A. 10 - 14 93% ∼ 3% N.A. N.A.
VADSBO DU 250 [RC] 20 ∼250W 2 - 15 89% ∼ 3% <4 2 - 11 87% ∼ 3% 2 - 15 89% ∼ 3% <4
Varilight HQ3W [R] 60-400W 3 - 27 94% ∼ 3% 2 - 18 93% ∼ 3% 3 - 27 94% ∼ 3% 3 - 8 99% ∼ 3%
Varilight ICT401 M [RC] 20-400W 2 - 20 84% ∼ 3% 2 - 18 87% ∼ 3% 2 - 20 84% ∼ 3%
Vimar 20148 [RL] 500W 2 - 30 94% ∼ 3% <3 2 - 20 94% ∼ 3% <2 2 - 30 94% ∼ 3% <3 2 - 8 99% ∼ 3% <2
Vimar 14153 [R] 2 - 20 99% ∼ 3% 2 - 13 94% ∼ 3% <2 2 - 20 99% ∼ 3%
Vimar 20160 [RC] 2 - 20 93% ∼ 3% <3 3 - 20 91% ∼ 3% 2 - 20 93% ∼ 3% <3
Vimar 20162 [RL] 40∼300W 4 - 30 95% ∼ 3% <3 2 - 20 96% ∼ 3% 4 - 30 95% ∼ 3% <3 2 - 8 99% ∼ 3% <2
IKEA E0902 - Dim [R] 25∼150W 2 - 10 95% ∼ 3% 2 - 7 94% ∼ 3% 2 - 10 95% ∼ 3% 2 - 8 99% ∼ 3%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
Image missing Image missing Image missing
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
Classic LED spot
GU10
LED CMN24:MT129U10
WarmGlow
GU10
LED Classic 50W
Warmglow
GU10
3.5 - 35W
Dimmable
GU10
4.6 - 50W
Dimmable
GU10
80W
Dim
28 29 30 31 32
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 2 - 8 94%- 8%
2 - 8
92%- 3% 2-20 91%~25% 2-15 85%~19% 2- 5 89%- 20%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 2 - 8 87%- 3% 2 - 8 93%- 3% 2-20 95%~24% 2-15 88%~19% 2- 5 93%- 20%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 2 - 8 86%- 4% 2 - 8 92%- 3% 2-18 93%~19% 2-15 89%~17% 2- 5 91%- 17%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 2 - 8 86%- 3% 2 - 8 94%- 3% 2-20 93%~10% 2-18 97%~6% 2- 5 93%- 7%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 2 - 8 89%- 3% 2 - 8 94%- 3% 2-20 96%~7% 2-20 98%~4% 2- 5 95%- 4%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 2 - 8 96%- 4% 2 - 8 94%- 3% 2-20 94%~23% 2-15 87%~20% 2- 5 92%- 18%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 2 - 8 89%- 3% 2 - 8 89%- 3% 2-20 90%~2% 2-20 93%~17% 2- 5 88%- 3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire)
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 2-20 96%~24% 2-18 96%~18%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) N.A. N.A. 2- 8 92%- 3% 2-20 92%~29% 2-15 85%~23% 2- 5 90%- 24%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 3- 8 95%- 3% 2- 8 92%- 3% 2-14 91%~6% 2-11 91%~5% 2- 5 89%- 4%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W N.A. N.A. 3- 8 95%- 3% 2-19 94%~14% 2-15 97%~13% 2- 5 95%- 12%
Eltako EVD61NPN-UC 400W 3-wire Push Module 2-14 99%~15% < 19 2-15 99%~14% < 16
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) N.A. N.A. 2- 8 92%- 3% 2-20 92%~29% 2-15 85%~23% 2- 5 90%- 24%
Feller| Schneider 40300 (SBD315) [RLC] 300W 3- 8 95%- 3% 2- 8 92%- 3% 2- 5 89%- 4%
Feller| Schneider 40420 (SBD420) [RLC] 420W N.A. N.A. 3- 8 95%- 3% 2- 5 95%- 12%
GIRA 1176-00/01 [RLC] 50 ∼ 420W 2-19 94%~36% 2-15 95%~32%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 2 - 8 91%- 3% 2-13 97%~13% 2-18 90%~14% 2- 5 88%- 36%
Hager EVN 011 [RC] 300VA 2-14 97%~19% < 6 2-11 97%~16% < 12
Hager EVN 012 [RC] 300W 2-14 98%~19% < 5 2-11 97%~16% < 12
Hager EVN 004 [RL] 500VA 2-20 98%~19% 2-18 97%~16%
INSTA 1176 [RLC] 50 ∼ 420W
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 2 - 8 96%- 8% 2 - 8 91%- 3% 2-20 92%~26% 2-15 87%~22% 2- 5 89%- 19%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 2 - 8 91%- 3% 2 - 8 91%- 3% 2-20 93%~37% 2-20 88%~35% 2- 5 88%- 11%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 2-5 88%~3% 2-4 87%~37%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 2-14 93%~3% N.A. N.A.
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. 2 - 8 94%- 3% N.A. N.A. N.A. N.A. 2- 5 94%- 17%
Legrand 78401 [RLC] 40 ∼ 500W 2-18 96%~3% < 3 2-15 92%~16% < 3
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. 3 - 8 95%- 3% N.A. N.A. N.A. N.A. 2- 5 93%- 15%
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. 3 - 8 94%- 3% N.A. N.A. N.A. N.A. 2- 5 95%- 17%
Legrand 67083 [RLC] 3 ∼ 400W 2-3 89%~12% N.A. N.A.
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 2 - 8 96%- 4% <3 2 - 8 93%- 3% 2-18 98%~20% 2-15 88%~15% 2- 5 93%- 13%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 2 - 8 99%- 3% 2 - 8 95%- 3% N.A. N.A. 2-11 99%~3% 2- 5 97%- 3%
Legrand L4402N [R] 60∼500W 8-20 91%~30% 3-18 86%~28%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) N.A. N.A. 2- 8 92%- 3% 2-20 92%~29% 2-15 85%~23% 2- 5 90%- 24%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 3- 8 95%- 3% 2- 8 92%- 3% 2-14 91%~6% 2-11 91%~5% 2- 5 89%- 4%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA N.A. N.A. 3- 8 95%- 3% 2-19 94%~14% 2-15 97%~13% 2- 5 95%- 12%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn N.A. N.A. 2 - 8 70%- 3% 3-20 85%~20% 2-15 77%~15% 2- 5 81%~17%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 2 - 8 80%- 3% 2 - 8 87%- 3% 3-20 89%~19% 2-18 81%~17% 2- 5 86%~15%
MK - Electric K4501 WHILV [RLC] 180W 3-10 89%~19% 2-8 90%~19%
MK - Electric K4500 WHILV [RLC] 400W 3-15 90%~20% 2-15 88%~19%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 2-5 89%~10% 2-4 87%~10%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 2 - 8 89%- 3% 2 - 8 89%- 3% 2-20 90%~3% 2-20 93%~17% 2- 5 88%- 3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 3- 8 95%- 3% 2- 8 92%- 3% 2-14 91%~6% 2-11 91%~5% 2- 5 89%- 4%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 3- 8 95%- 3% 2- 8 92%- 3% 2-14 91%~6% 2-11 91%~5% 2- 5 89%- 4%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) N.A. N.A. 2- 8 92%- 3% 2-20 92%~29% 2-15 85%~23% 2- 5 90%- 24%
Schneider SBD315RC (SBD 315) [RC] 315W 3- 8 95%- 3% 2- 8 92%- 3% 2-14 91%~6% 2-11 91%~5% 2- 5 89%- 4%
VADSBO ED 350 [RC] 50 ∼350W 2-16 93%~34% 2-13 88%~29%
VADSBO DRS 315 [RC] 50 ∼315W 8-14 95%~24% < 15 3-11 97%~21% < 12
VADSBO DU 250 [RC] 20 ∼250W 2-11 89%~11% < 12 2-9 89%~9% < 10
Varilight HQ3W [R] 60-400W 2 - 8 85%- 3% 2 - 8 93%- 3% 2-18 98%~14% 2-15 88%~8% 2- 5 91%- 10%
Varilight ICT401 M [RC] 20-400W 2-18 94%~10% 2-15 92%~7%
Vimar 20148 [RL] 500W 2 - 8 87%- 3% <9 3 - 8 92%- 3% <9 2-20 94%~17% 2-18 88%~16% < 4 2- 5 93%~14% <6
Vimar 14153 [R] 2-20 98%~3% 2-18 97%~9%
Vimar 20160 [RC] 2-14 94%~13% < 15 2-18 94%~12% < 19
Vimar 20162 [RL] 40∼300W 2 - 8 94%- 4% <9 2 - 8 91%- 3% <9 3-13 93%~14% 2-11 84%~11% < 4 2- 5 90%~13% <6
IKEA E0902 - Dim [R] 25∼150W 2 - 8 87%- 3% <2 2 - 6 93%- 3% t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. 2- 5 94%~3%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
Classic LED spot
R50
5W - 60W
Dimmable
PAR20
50W
PAR30
75W
PAR38
100W
33 34 35 36
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 2-10 90%~20%
1 - 10
91%- 12% 1 - 8 93%- 12% 1 - 5 94%- 13%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 2-10 94%~8% 1 - 5 93%- 6% 1 - 8 96%- 11% 1 - 5 96%- 12%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 2-10 94%~16% < 2 1 - 10 93%- 6% 1 - 8 95%- 11% 1 - 8 97%- 57%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 2-10 92%~3% 1 - 14 92%- 3% 1 - 11 94%- 3% 1 - 8 95%- 3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 2-10 92%~3% 1 - 8 95%- 3% 1 - 13 96%- 3% 1 - 9 96%- 3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 2-10 96%~20% 1 - 15 92%- 12% 1 - 9 93%- 12% 1 93%- 12%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 2-10 92%~3% 1 - 14 93%- 3% 1 - 11 95%- 3% 1 - 15 96%- 3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire) T.B.D. T.B.D. T.B.D.
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1-16 95%~20% 1 - 17 94%- 10% 1 - 11 95%- 12% 1 - 8 93%- 11%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2-10 88%~20% 1 - 10 92%- 14% 1 - 8 92%- 18% 1 - 5 93%- 15%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 2-10 88%~3% 1 - 9 92%- 4% 1 - 7 94%- 4% 1 - 5 94%- 4%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W N.A. N.A. 1 - 12 94%- 7% 1 - 9 96%- 7% N.A. N.A.
Eltako EVD61NPN-UC 400W 3-wire Push Module 1-16 97%~12% <17 1 - 13 98%- 7% 1 - 8 95%- 7% 1 - 6 96%- 8%
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2-10 88%~20% 1 - 10 92%- 14% 1 - 8 92%- 18% 1 - 5 93%- 15%
Feller| Schneider 40300 (SBD315) [RLC] 300W 1 - 9 92%- 4% 1 - 7 94%- 4% 1 - 5 94%- 4%
Feller| Schneider 40420 (SBD420) [RLC] 420W 1 - 12 94%- 7% 1 - 9 96%- 7% N.A. N.A.
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1-16 94%~30% 1 - 14 96%- 17% 1 - 9 88%- 7% N.A. N.A.
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 2-10 92%~8% 1 - 10 93%- 3% 1 - 9 97%- 3% 1 - 5 94%- 4%
Hager EVN 011 [RC] 300VA 1-12 97%~14% < 13 1 - 10 98%- 8% 1 - 6 96%- 6% 5 97%- 9%
Hager EVN 012 [RC] 300W 1-12 96%~15% < 13 1 - 10 98%- 13% 1 - 6 96%- 14% 5 97%- 14%
Hager EVN 004 [RL] 500VA 1-16 97%~15% < 3 1 - 17 98%- 14% 1 - 11 97%- 14% 8 97%- 14%
INSTA 1176 [RLC] 50 ∼ 420W t.b.d. t.b.d. t.b.d.
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 2-10 92%~24% 1 - 15 98%- 13% 1 - 11 93%- 13% 1 - 8 92%- 14%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 2-10 92%~36% 1 - 10 92%- 3% 1 - 10 94%- 3% 1 - 8 95%- 3%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1-5 79%~31% 1 - 4 93%- 19% 1 - 3 89%- 20% 1 - 2 92%- 21%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 1-12 87%~14% 1 - 10 58%- 3% 1 - 6 84%- 3% 1 - 5 81%- 3%
Legrand 774161 [RL] 40 ∼ 400 W - Turn 3-10 92%~8% < 4 2 - 11 93%- 6% 1 - 8 96%- 6% 1 - 6 97%- 7%
Legrand 78401 [RLC] 40 ∼ 500W 1-16 95%~14% 1 - 13 94%- 7% 5- 8 93%- 8% N.A. N.A.
Legrand 67081 [RL] 40 ∼ 400 W - Turn 3-10 96%~16% 2 - 9 94%- 5% 1 - 6 96%- 3% 1 - 5 98%- 7%
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. 2 - 15 94%- 5% 1 - 13 96%- 3% N.A. N.A.
Legrand 67083 [RLC] 3 ∼ 400W 2-16 90%~12% 1 - 3 94%- 3% 1 - 2 89%- 3% 1 - 6 92%- 3%
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 2-10 88%~3% < 5 1 - 11 93%- 8% 1 - 8 94%- 3% N.A. N.A.
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 2-10 96%~3% 1 - 9 97%- 3% 1 - 6 98%- 3% N.A. N.A.
Legrand L4402N [R] 60∼500W 2-16 95%~20% N.A. N.A. N.A. N.A. 2- 3 91%- 15%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 2-10 88%~20% 1 - 10 92%- 14% 1 - 8 92%- 18% 1 - 5 93%- 15%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 2-10 88%~3% 1 - 9 92%- 4% 1 - 7 94%- 4% 1 - 5 94%- 4%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA N.A. N.A. 1 - 12 94%- 7% 1 - 9 96%- 7% N.A. N.A.
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 2-10 80%~14% 1 - 13 77%- 7% 1 - 5 84%- 5% 1 - 7 88%- 10%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 2-10 86%~14% 1 - 15 96%- 30% 1 - 7 84%- 5% 1 - 8 93%- 6%
MK - Electric K4501 WHILV [RLC] 180W 1-9 90%~17% 1 - 7 92%- 5% 1 - 9 93%- 8% 1 - 3 92%- 8%
MK - Electric K4500 WHILV [RLC] 400W 1-16 89%~18% 1 - 11 99%- 29% 1 - 11 93%- 6% 1 - 6 91%- 6%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1-5 89%~7% 1 - 4 95%- 3% 1 - 3 86%- 3% 1 - 2 91%- 3%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 2-10 92%~3% 1 - 14 93%- 3% 1 - 11 95%- 3% 1 - 15 96%- 3%
RELCO RP0977 [LED] 4-100W 1 - 3 99%- 15% 1 - 2 89%- 13% 1 - 2 99%- 17%
RELCO RM0545 [LED] 4-100W 1 - 3 92%- 8% 1 - 2 83%- 8% 1 - 3 93%- 9%
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 2-10 88%~3% 1 - 9 92%- 4% 1 - 7 94%- 4% 1 - 5 94%- 4%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 2-10 88%~3% 1 - 9 92%- 4% 1 - 7 94%- 4% 1 - 5 94%- 4%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 2-10 88%~20% 1 - 10 92%- 14% 1 - 8 92%- 18% 1 - 5 93%- 15%
Schneider SBD315RC (SBD 315) [RC] 315W 2-10 88%~3% 1 - 9 92%- 4% 1 - 7 94%- 4% 1 - 5 94%- 4%
VADSBO ED 350 [RC] 50 ∼350W 1-14 88%~27% 1 - 12 93%- 14% 1 - 7 82%- 13% 1 - 5 90%- 1%
VADSBO DRS 315 [RC] 50 ∼315W 2-13 95%~19% < 14 1 - 11 95%- 10% 1 - 7 90%- 10% 1 - 5 94%- 11%
VADSBO DU 250 [RC] 20 ∼250W 1-10 85%~9% < 11 1 - 14 96%- 17% 1 - 5 88%- 15 N.A. N.A.
Varilight HQ3W [R] 60-400W 2-10 92%~6% 1 - 8 91%- 5% 1 - 8 95%- 4% 1 - 6 94%- 5%
Varilight ICT401 M [RC] 20-400W 1-16 89%~6% 1 - 13 94%- 5% 1 - 8 89%- 5% 1 - 6 93%- 5%
Vimar 20148 [RL] 500W 3-10 92%~8% < 11 1 - 14 92%- 4% 1 - 11 97%- 3% 1 - 8 95%- 5%
Vimar 14153 [R] 1-16 99%~6% 1 - 15 99%- 3% 1 - 11 89%- 3% 1 - 8 96%- 3%
Vimar 20160 [RC] 2-16 94%~11% < 17 1 - 10 95%- 3% 1 - 6 90%- 3% 1 - 8 92%- 3%
Vimar 20162 [RL] 40∼300W 2-10 88%~8% < 11 1 - 9 91%- 7% 1 - 6 96%- 8% 1 - 5 35%- 7%
IKEA E0902 - Dim [R] 25∼150W t.b.d. t.b.d. t.b.d. 2- 5 94%- 9% 1- 3 92%- 3% 1- 2 98%- 14%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LEDflame
E27 A60
25W
E27 A60
45W
37 38
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 1-3 94%~3%
1-3
95%~3%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 1-3 96%~3% 1-3 92%~11%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. N.A. N.A.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 1-3 98%~9% 1-3 94%~15%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn N.A. N.A. 1-3 95%~3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 1-3 99%~3% 1-3 92%~3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 98%~5% 92%~4%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 1-3 94%~3% 1-3 94%~3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire) T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 1-3 91%~13% 1-3 92%~19%
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 3 91%~3% 1-3 91%~7%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 1-3 93%~3% 1-3 98%~3%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W 1-3 91%~3% 1-3 93%~3%
Eltako EVD61NPN-UC 400W 3-wire Push Module T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 3 91%~3% 1-3 91%~7%
Feller| Schneider 40300 (SBD315) [RLC] 300W
Feller| Schneider 40420 (SBD420) [RLC] 420W
GIRA 1176-00/01 [RLC] 50 ∼ 420W 1-3 93%~15% 1-3 93%~13%
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 1-3 94%~3% 1-3 99%~3%
Hager EVN 011 [RC] 300VA 1-3 97%~3% 1-3 97%~3%
Hager EVN 012 [RC] 300W 1-3 97%~3% 1-3 97%~3%
Hager EVN 004 [RL] 500VA 1-3 97%~3% 1-3 97%~3%
INSTA 1176 [RLC] 50 ∼ 420W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 1-3 92%~8% 1-3 93%~7%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 1-3 95%~3% 1-3 93%~3%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 1-3 84%~12% 1-3 87%~20%
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer T.B.D. T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A.
Legrand 78401 [RLC] 40 ∼ 500W 1-3 93%~3% 1-3 93%~3%
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A.
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A.
Legrand 67083 [RLC] 3 ∼ 400W N.A. N.A. N.A. N.A.
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 98%~3% 92%~3%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 96%~3% 97%~3%
Legrand L4402N [R] 60∼500W N.A. N.A. 2-3 87%~11%
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 3 91%~3% 1-3 91%~7%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 1-3 93%~3% 1-3 98%~3%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA 1-3 91%~3% 1-3 93%~3%
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 1-3 82%~3% 1-3 84%~6%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 1-3 89%~3% 1-3 92%~3%
MK - Electric K4501 WHILV [RLC] 180W 1-3 87%~3% 1-3 88%~3%
MK - Electric K4500 WHILV [RLC] 400W 1-3 87%~3% 1-3 87%~3%
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 1-3 85%~12% 1-3 89%~27%
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 1-3 94%~3% 1-3 94%~3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 1-3 93%~3% 1-3 98%~3%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 1-3 93%~3% 1-3 98%~3%
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 3 91%~3% 1-3 91%~7%
Schneider SBD315RC (SBD 315) [RC] 315W 1-3 93%~3% 1-3 98%~3%
VADSBO ED 350 [RC] 50 ∼350W 1-3 89%~16% 1-3 85%~11%
VADSBO DRS 315 [RC] 50 ∼315W 1-3 92%~3% 1-3 92%~3%
VADSBO DU 250 [RC] 20 ∼250W 1-3 87%~3% 1-3 83%~3%
Varilight HQ3W [R] 60-400W 1-3 95%~3% 1-3 95%~3%
Varilight ICT401 M [RC] 20-400W t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
Vimar 20148 [RL] 500W N.A. N.A. 1-3 94%~3%
Vimar 14153 [R] 1-3 99%~3% 1-3 99%~3%
Vimar 20160 [RC] N.A. N.A. 1-3 92%~3%
Vimar 20162 [RL] 40∼300W 1-3 95%~5% 1-3 88%~3%
IKEA E0902 - Dim [R] 25∼150W 1-3 96%~2% 1-3 95%~10%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
Image missing Image missing
July 2017
www.philips.com
KEY
Consumer LED Mains Voltage range
Recommended dimmer compatibility list for Mains Voltage Lamps
x-y
Excellent dimming with X-Y lamps, however external factors can negatively influence the deep dimming performance
This document is for information purposes
and must be treated as recommendation.
Philips attempted to provide best results,
results are generated in lab conditions and
might contain faults
x-y
Dimming performance: These dimmers require more than 5 lamps as minimum load
Unexpected performance behavior, not in line with good dimming perception
N.A.
Dimmer lamp combination not applicable
t.b.d.
Dimmer lamp combination not tested
LED capsule
G9
2.5 - 25W
Dimmable
R7S (118mm)
14 - 100W
Dimmable
39 40
Dimming
Performance
Dimming
Range
Glowing
Dimming
Performance
Dimming
Range
Glowing
Brand Type Type Load
Berker |INSTA 286710 [RC] 20 ∼ 360 W - Turn 3-20 96%~27%
1
89%- 8%
Berker |INSTA 283010 [R] 60 ∼ 400 W - Turn 3-20 86%~23% 1 94%- 3%
Bticino L4407 [] 60 ∼ 250 W N.A. N.A. t.b.d. t.b.d. t.b.d.
Busch Jaeger |ABB 2200 U - 503 [R] 60 ∼ 400 W - Turn 3-20 85%~33% 1 91% - 23%
Busch Jaeger |ABB 2247 U [RL] 20 ∼ 500 W - Turn 3-20 83%~9% 1 93%~3%
Busch Jaeger |ABB 2250 U [R] 60 ∼ 600 W - Turn 3-20 87%~6% 1 96%~3%
Busch Jaeger |ABB 6513 U - 102 [RC] 40 ∼ 420 W - Turn 3-20 98%~24% 1 93%~7%
Busch Jaeger |ABB 6523 U [LED] 2 ∼ 100 VA-LED - Turn 3-20 92%~3% 1 88%~3%
Busch Jaeger |ABB 6524 U [LED] 2 ∼ 100 VA-LED - Push (3wire)
Busch Jaeger |ABB 6526 U [LED] 2 ∼ 100 VA-LED - Push (2wire) 3-20 97%~23% < 7 t.b.d. t.b.d. t.b.d.
ELKO| Schneider SBD200LED (CCTEL10501) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 3-20 96%~30% 1 89%~3%
ELKO| Schneider SBD315RC (315 GLE ) [RC] 315W 3-20 95%~9% 1 88%~10%
ELKO| Schneider SBD420RCRL (CCTEL13011) [RLC] 420W N.A. N.A. t.b.d. t.b.d. t.b.d.
Eltako EVD61NPN-UC 400W 3-wire Push Module 3-20 99%~15% t.b.d. t.b.d. t.b.d.
Feller| Schneider 40200 (SBD200LED CCTCH10601) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 3-20 96%~30% 1 89%~3%
Feller| Schneider 40300 (SBD315) [RLC] 300W
Feller| Schneider 40420 (SBD420) [RLC] 420W
GIRA 1176-00/01 [RLC] 50 ∼ 420W 3-20 96%~39% < 12 t.b.d. t.b.d. t.b.d.
GIRA 2390 00/ 100 7 ∼ 100W - Push (3wire) 3-18 91%~15% 1 89%'4%
Hager EVN 011 [RC] 300VA 3-20 98%~18% < 14 t.b.d. t.b.d. t.b.d.
Hager EVN 012 [RC] 300W 3-20 99%~28% < 14 t.b.d. t.b.d. t.b.d.
Hager EVN 004 [RL] 500VA 3-20 99%~28% < 15 t.b.d. t.b.d. t.b.d.
INSTA 1176 [RLC] 50 ∼ 420W
Jung 225 TDE [RC] 20 ∼ 525 W - Turn 3-20 96%~33% 1 90%~10%
Jung 1271LEDDE [LED] 3 ∼ 100W - Push (3wire) 3-20 94%~3% 1 90%- 3%
Klik aan Klik uit AWMD-250 [LED] 3∼ 24W 3-10 86%~3% < 11 t.b.d. t.b.d. t.b.d.
Klik aan Klik uit ACM 300 300W - 3-wire Push LED Dimmer 3-20 33%~3% < 10 t.b.d. t.b.d. t.b.d.
Legrand 774161 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A.
Legrand 78401 [RLC] 40 ∼ 500W 3-20 97%~3% < 13 t.b.d. t.b.d. t.b.d.
Legrand 67081 [RL] 40 ∼ 400 W - Turn N.A. N.A. N.A. N.A.
Legrand 67082 [RL] 40 ∼ 600 W - Turn N.A. N.A. N.A. N.A.
Legrand 67083 [RLC] 3 ∼ 400W N.A. N.A. t.b.d. t.b.d. t.b.d.
Legrand 67084 [RLC] 8 - 300 VA - Push LED (3wire) 3-20 97%~23% 1 93%~3%
Legrand 67085 (078406) [RLC] 8 - 300 VA - Push LED (3wire) 3-20 99%~4% 1 98%~3%
Legrand L4402N [R] 60∼500W N.A. N.A. t.b.d. t.b.d. t.b.d.
Merten| Schneider SBD200LED (MEG5134-0000) [LED/RC] 4 ∼ 200W(RC) 4∼400W(RL) 3-20 96%~30% 1 89%~3%
Merten| Schneider SBD315RC (MEG5136-0000) [RC] 315W 3-20 95%~9% 1 88%~10%
Merten| Schneider SBD420RCRL (MEG5138-0000) [RLC] 20∼420 VA t.b.d. t.b.d. t.b.d. t.b.d. t.b.d. t.b.d.
MK - Electric K1535 [R] 65 ∼ 450 W - Turn 3-20 72%~19% 1 82%~10%
MK - Electric K1501 WHILV [R] 60 ∼ 500 W - Turn 3-10 82%~17% 1 88%~6%
MK - Electric K4501 WHILV [RLC] 180W N.A. N.A. t.b.d. t.b.d. t.b.d.
MK - Electric K4500 WHILV [RLC] 400W N.A. N.A. t.b.d. t.b.d. t.b.d.
PEHA 431HAN [RL] 6∼120W [LED] 6∼60W 3-10 76%~4% t.b.d. t.b.d. t.b.d.
Philips UID8670 [LED] 2 ∼ 100 VA-LED - Push (3wire) 3-20 92%~3% 1 88%~3%
RELCO RP0977 [LED] 4-100W
RELCO RM0545 [LED] 4-100W
Schneider SBD315RC (SBD 315, SDD 315) [RC] 315W 3-20 95%~9% 1 88%~10%
Schneider SBD315RC (ATD315)(CCT011533) [RC] 315W 3-20 95%~9% t.b.d. t.b.d. t.b.d.
Schneider SBD200 (WDE 002299) [] 4∼400VA - Turn Universal (2wire) 3-20 96%~30% 1 89%~3%
Schneider SBD315RC (SBD 315) [RC] 315W 3-20 95%~9% 1 88%~10%
VADSBO ED 350 [RC] 50 ∼350W 5-20 93%~34% t.b.d. t.b.d. t.b.d.
VADSBO DRS 315 [RC] 50 ∼315W N.A. N.A. t.b.d. t.b.d. t.b.d.
VADSBO DU 250 [RC] 20 ∼250W 3-20 92%~14% <21 t.b.d. t.b.d. t.b.d.
Varilight HQ3W [R] 60-400W 3-20 85%~14% 1 93%~3%
Varilight ICT401 M [RC] 20-400W 3-20 85%~14% < 11 t.b.d. t.b.d. t.b.d.
Vimar 20148 [RL] 500W N.A. N.A. 1 94%~4%
Vimar 14153 [R] 3-20 98%~3% <10 1 90%~5%
Vimar 20160 [RC] N.A. N.A.
Vimar 20162 [RL] 40∼300W 3-20 96%~18% <21 t.b.d. t.b.d. t.b.d.
IKEA E0902 - Dim [R] 25∼150W 3-20 96%~6% 1 93%~9%
Note :
#1) Unexpected behaviour can occur outside the range of specified number of lamps. The mentioned numbers are tested. In some cases the dimmers can be loaded with more lamps than is specified in this document (most dimmers can be loaded with LED
lamps to 20% of specified power; LED dimmers can be loaded to specified power)
#2) Occupancy sensors can act like dimmers, therefore Philips recommends to use dimmable lamps in combination with it.
#3) Glowing means: a switched off dimmer still having the possibility that a small light output is visible. This status can occur when a low quantity of lamps is connected.
#4) Yellow cells indication: Sometimes flickering is observed due to low dimmer loads, best visible at deep dimming
#4a) Yellow cells indication: Dimming performance: LED's have much lower load (wattage) than traditional lightsources. (e.g. flickering where "active loads" can reduce your problems)
#4b) Yellow cells indication: Dimming range, minimum dim level with the indicated dimmer will be somewhere between 10%-30%
#5) Various dimmer suppliers offer "active loads" (e.g. Busch Jaeger Kompensator 6596) to optimize dimming performance in case of lamp-dimmer system issues. Using double pole switches will prevent glowing issues.
#7) This list is based on measurements in a lab environment with nominal voltage, a different voltage will result in a different dimming range. Therefor we indicated 3% as minimum lightlevel as labcondition.
#8) Dimmermanufacturers may change the technical design of the dimmer without informing LED lamp suppliers. These changes can influence the performace of LED products.
Philips cannot be held responsible for inaccuracies in the compatibility lists due to technical changes in dimmers
Disclaimer:
Philips will not accept claims for any damage caused by implementing the recommendations in this document.
www.philips.com© Philips Lighting Holding B.V. 2016. All rights reserved. Philips reserves the right to make changes
in specifications and/or to discontinue any product at any time without notice or obligation and
will not be liable for any consequences resulting from the use of this publication.
08/2016
Data subject to change.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Philips 8718696693032 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Eltako GFVS-Safe II Quick start guide
-
PEAK NX Adapter for the Flush-Mounted Box of the Merten Touch Panel 7 Operating instructions
-
Legrand 7 525 66 User manual
-
Samsung SI-P8W152BB1EU Datasheet
-
-
-
-
Trust 20148 Datasheet
-
Hager SL200559409011 User manual
-