Schwinn 470i Assembly & Owner's Manual

Schwinn
Brand
Schwinn
Model
470i
Category
Spin bikes
Type
Assembly & Owner's Manual
This product is compliant with the
applicable CE requirements.
ASSEMBLY MANUAL / OWNER’S MANUAL
470i
2
Important Safety Instructions - Assembly 3
Safety Warning Labels / Serial Number 4
Specications 5
BeforeAssembly 5
Parts 6
Hardware 7
Tools 7
Assembly 8
Moving the Machine 20
Leveling the Machine 21
Important Safety Instructions 22
Features 23
Console Features 24
Operations 29
Mounting and Dismounting 29
Power Up / Idle Mode 29
Quick Start Program 30
UserProles 30
Pausing or Stopping 36
Results / Cool Down Mode 36
GOAL TRACK Statistics 37
Console Service Mode 39
Maintenance 41
Maintenance Parts 42
Troubleshooting 44
Table of ConTenTs
Nautilus,Inc.,www.NautilusInc.com,18225NERiversideParkway,Portland,OR97230,U.S.A.-CustomerService:
[email protected] | Printed in China | © 2013 Nautilus, Inc.
Tovalidatewarrantysupport,keeptheoriginalproofofpurchaseandrecordthefollowinginformation:
Serial Number __________________________
Date of Purchase ____________________
To register your product warranty, contact your local distributor.
If you have questions or problems with your product, please contact your local Schwinn
®
distributor.
To find your local distributor, go to: www.nautilusinternational.com
3
Important Safety InStructIonS
-aSSembly
This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
Read and understand all warnings on this machine.
Carefully read and understand the Assembly instructions.
• Keepbystandersandchildrenawayfromtheproductyouareassemblingatalltimes.
• Donotconnectpowersupplytothemachineuntilinstructedtodoso.
• Donotassemblethismachineoutdoorsorinawetormoistlocation.
• Makesureassemblyisdoneinanappropriateworkspaceawayfromfoottrafficandexposuretobystanders.
• Somecomponentsofthemachinecanbeheavyorawkward.Useasecondpersonwhendoingtheassemblysteps
involvingtheseparts.Donotdostepsthatinvolveheavyliftingorawkwardmovementsonyourown.
• Setupthismachineonasolid,level,horizontalsurface.
• Donottrytochangethedesignorfunctionalityofthismachine.Thiscouldcompromisethesafetyofthismachineandwill
void the warranty.
• Ifreplacementpartsarenecessary,useonlygenuineNautilus®replacementpartsandhardware.Failuretousegenuine
replacementpartscancausearisktousers,keepthemachinefromoperatingcorrectlyandvoidthewarranty.
• Donotuseuntilthemachinehasbeenfullyassembledandinspectedforcorrectperformanceinaccordancewiththe
Manual.
• ReadandunderstandthecompleteManualsuppliedwiththismachinebeforefirstuse.KeeptheManualforfuture
reference.
• Doallassemblystepsinthesequencegiven.Incorrectassemblycanleadtoinjuryorincorrectfunction.
• Thisproductcontainsmagnets.Magneticfieldscaninterferewiththenormaluseofcertainmedicaldevicesataclose
range.Usersmaycomeintoproximityofthemagnetsintheassembly,maintenance,and/oruseoftheproduct.Giventhe
obviousimportanceofthesedevices,suchasapacemaker,itisimportantthatyouconsultwithyourmedicalprovider
inconnectionwiththeuseofthisequipment.Pleaseconsultthe“SafetyWarningLabelsandSerialNumber”sectionto
determine the location of the magnets on this product.
4
Safety WarnIng labelS and SerIal
number
SerialNumber
REVISIONS
ECO
REVISION
REV DESCRIPTION
APPROVED
DATE
TITLE.
PART NO.
REV.
SHEET 1 OF 1
SCALE: 1:1
DO NOT SCALE DRAWING
1. ALL ITEMS MUST BE RoHS COMPLIANT
2. ALL DIMENSIONS APPLY BEFORE PLATING OR COATING.
3. REMOVE ALL BURRS, BREAK SHARP EDGES 0.5 MM MAX.
4. ALL MACHINES SURFACES Ra 3.2 uM.
5. ALL APPLICABLE NAUTILUS STANDARDS AND
SPECIFICATIONS APPLY.
6. ALL DIMENSIONS ARE IN MILLIMETERS
7. ALL DUAL DIMENSIONS ARE IN INCH
UNLESS OTHERWISE SPECIFIED:
METRIC
THIRD ANGLE
PROJECTION
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M - 1994
2.5
1.5
0.75
0.25
1°
X.
X.X
X.XX
X.XXX
ANGULAR
C
SIZE
This document is the property of Nautilus, Inc. It may not be reproduced in whole or part, provided to third parties, or used for any purposes other than the performance of work for Nautilus, Inc. without written authorization. All rights are reserved, including copyrights.
TOLERANCES.
DRAWN
DESIGNED
DATE
METRIC_C_REV G
NAUTILUS, INC.
16400 SE NAUTILUS DRIVE, VANCOUVER, WA 98683
LIFECYCLE
- -
APPROVALS
- -
- - - -
WARRANTY ITEM:
L.SEVIER
3/29/2013
L.SEVIER
A
8002739
GWl BIKE AND ELLIPTICAL 300lb 2013
MATERIAL.
COLOR.
DIE LINE
PMS 152
PMS 109
BLACK
WHITE
Labels must be created from an agency approved tamper proof labeling system
such as "UL Recognized component marking and labeling system (example: UL PGGU2) or equivalent.
Label and adhesive must be rated for surface it is applied to (painted metal or ABS plastic),
Label and adhesive must be rated for 60 degrees C minimum. Labels must meet UL 1647 Permanence of Marking Test.
50mm
117.7mm
A RELEASE 3/29/2013
LSEVIER
xxxxxxx
• Lisez et assimilez tous les avertissements
apposés sur cet appareil.
• Gardez les enfants et les animaux de
compagnie éloignés de cette machine en
tout temps
• Déconseillé aux enfants âgés de
moins de 14 ans.
• Lisez et familiarisez-vous avec le Manuel
du propriétaire et avec tous les
avertissements avant d’utiliser cette
machine.
• Soyez prudent lorsque vous utilisez cet
équipement pour ne pas vous infliger de
graves blessures.
• Cette machine supporte un poids
maximal de 300lbs. (136kg).
• Remplacez toute étiquette
d’avertissement endommagée, illisible
ou manquante.
• La fréquence cardiaque qui s’affiche
sur la console peut être inexact et
doit être utilisée seulement à titre
indicatif.
• Read, understand and obey all
warnings on this machine.
• Keep children away.
• Not intended for use by anyone
under 14 years of age.
• Prior to use, read and understand
the Owner’s Manual.
• Injury or death is possible if
Caution is not used while using this
machine.
• The maximum user weight for this
machine is 300 lbs (136 kg).
• Replace any “Caution”, “Warning”
or “Danger” label that is illegible,
damaged, or removed.
• The heart rate displayed may be
inaccurate and should be used for
reference only.
8002739_A
ProductSpecifications
REVISIONS
ECO
REVISION
REV DESCRIPTION
APPROVED
DATE
TITLE.
PART NO.
REV.
SHEET 1 OF 1
SCALE: 1:1
DO NOT SCALE DRAWING
1. ALL ITEMS MUST BE RoHS COMPLIANT
2. ALL DIMENSIONS APPLY BEFORE PLATING OR COATING.
3. REMOVE ALL BURRS, BREAK SHARP EDGES 0.5 MM MAX.
4. ALL MACHINES SURFACES Ra 3.2 uM.
5. ALL APPLICABLE NAUTILUS STANDARDS AND
SPECIFICATIONS APPLY.
6. ALL DIMENSIONS ARE IN MILLIMETERS
7. ALL DUAL DIMENSIONS ARE IN INCH
UNLESS OTHERWISE SPECIFIED:
METRIC
THIRD ANGLE
PROJECTION
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M - 1994
2.5
1.5
0.75
0.25
1°
X.
X.X
X.XX
X.XXX
ANGULAR
C
SIZE
This document is the property of Nautilus, Inc. It may not be reproduced in whole or part, provided to third parties, or used for any purposes other than the performance of work for Nautilus, Inc. without written authorization. All rights are reserved, including copyrights.
TOLERANCES.
DRAWN
DESIGNED
DATE
METRIC_C_REV G
NAUTILUS, INC.
16400 SE NAUTILUS DRIVE, VANCOUVER, WA 98683
LIFECYCLE
7-22-10
APPROVALS
- -
- - - -
WARRANTY ITEM:
A RELEASED
NPI 13149 DLOVELY
7-22-10
D.LOVELY
D.LOVELY
07 /22 / 2010
D.LOVELY
A
004-0930
CRUSH WARNING
21.78mm
54.8mm
MATERIAL.
COLOR.
DIE LINE
PMS 152
PMS 109
BLACK
WHITE
Labels must be created from an agency approved tamper proof labeling system
such as "UL Recognized component marking and labeling system (example: UL PGGU2) or equivalent.
Label and adhesive must be rated for surface it is applied to (painted metal or ABS plastic),
Label and adhesive must be rated for 60 degrees C minimum. Labels must meet UL 1647 Permanence of Marking Test.
•
•
Grounding Instructions
Thisproductmustbeelectricallygrounded.Ifamalfunctionoccurs,correctgroundingdecreasestheriskofelectricshock.
Thepowercordisequippedwithanequipment-groundingconductor,andmustbeconnectedtoanoutletthatisproperly
installed and grounded.
Theelectricalwiringmustcomplywithallapplicablelocalandprovincialstandardsandrequirements.Incorrect
connectionoftheequipment-groundingconductorcanresultinariskofelectricshock.Consultalicensed
electricianifyouarenotsurethatthemachineiscorrectlygrounded.Donotchangetheplugonthemachine
– if it does not fit the outlet, have a correct outlet installed by a licensed electrician.
ASurgeProtectorDeviceisrecommendedtoprotectthemachine.
IfaSurgeProtectorDevice(SPD)isusedwiththismachine,besurethatitisUL1449ratedorequivalent,andmatches
thepowerratingofthisequipment(220-240VAC).Donotconnectotherappliancesordevicestothesurgeprotector
in combination with this machine.
Makesurethattheproductisconnectedtoanoutlethavingthesameconfigurationastheplug.Noadaptershouldbeused
with this product.
5
SpecIfIcatIonS
Before Assembly
Selecttheareawhereyouaregoingtosetupandoperateyourmachine.Forsafeoperation,thelocationmustbeona
hard,levelsurface.Allowaworkoutareaofaminimum193.4cmx300cm(76.2”x118.1”).Besurethattheworkout
spaceyouareutilizinghasadequateheightclearance,takingintoconsiderationtheheightoftheuserandthemaximum
incline of the elliptical machine.
Basic Assembly Tips
Followthesebasicpointswhenyouas-
semble your machine:
• Readandunderstandthe“Important
SafetyInstructions”beforeassembly.
• Collect all the pieces necessary for
each assembly step.
• Usingtherecommendedwrenches,
turn the bolts and nuts to the right
(clockwise)totighten,andtheleft
(counterclockwise)toloosen,unless
instructed otherwise.
• Whenattaching2pieces,lightlylift
andlookthroughtheboltholesto
help insert the bolt through the holes.
• Theassemblycanrequire2people.
Maximum User Weight: 136kg(300lbs.)
Machine Weight: 76.5kg(168.7lbs.)
Total Surface Area (foot print) of equipment:
12734.2cm
2
(1976.8inches
2
)
Power Requirements:
OperationalVoltage: 220V-240VAC,50Hz
OperatingCurrent: 1A
Complies with the following directives: 2004/108/EC-Electromagnetic
Compatibility,2006/95/EC–LowVoltageDirective
This product has been tested to the following standards:
EMC:
EN55014-1:2006+A2:2011
EN55014-2:1997+A2:2008
Safety:
IEC60335-1:2010Safetyofhouseholdandsimilarelectricalappliances
NationalDifferences:
Australian/NewzealandAS/NZS60335.1:2011
EuropeanGroupDifferences:EN60335-1:2012
160.5 cm
( 63.2” )
178.1 cm
( 70.1” )
71.5 cm
( 28.2” )
ThisproductconformstotheapplicableENISO20957InternationalStandardsforStationaryTrainingEquipment,ClassH.
DONOTdisposeofthisproductasrefuse.Thisproductistoberecycled.Forproperdisposalofthisproduct,please
follow the prescribed methods at an approved waste center.
3.0m ( 118.1” )
1.93m
( 76.2” )
0.6m
( 24” )
0.6m
( 24” )
0.6m
( 24” )
0.6m
( 24” )
6
Adecalhasbeenappliedtoallright(“R ”)andleft(“L ”)partstoassistwithassembly.
Item Qty Description Item Qty Description
1 1 ConsoleMast 12 1 UpperShroud
2 1 StaticHandlebar 13 1 FrontStabilizer
3 1 ArmPivotRod 14 2 HandlebarShroud,Inner
4 1 WaterBottleHolder 15 2 HandlebarShroud,Outer
5 1 Console 16 1 RightLeg
6 1 UpperLeftHandlebarArm 17 1 RightPedal
7 1 LowerLeftHandlebarArm 18 1 ShroudCap
8 1 LeftPedal 19 1 LowerRightHandlebarArm
9 1 Rail Assembly 20 1 UpperRightHandlebarArm
10 1 LeftLeg 21 1 PowerCord
11 1 Frame 22 1 MP3Cord
partS
1
4
6
5
2
3
12
7
8
10
11
9
18
16
13
20
19
17
15
14
15
14
21
22
7
HardWare / toolS
Tools
Included
Item Qty Description Item Qty Description
A 6 ButtonHeadHexScrew,M8x16(with
Loctite
®
adhesive)
F 6 WaveWasher
B 4 FlatWasher,M8 G 12 LockWasher,M8
C 8 WideWasher,M8 H 2 PivotSleeve
D 4 ButtonHeadHexScrew,M8x16 I 4 PhillipsHeadScrew,M5x12
E 2 HexHeadScrew,M8x20
6mm
A B C D E F
G H
I
#2
13mm
15mm
19mm
8
aSSembly
1. Attach Front Stabilizer to Frame
Note:Hardwareispre-installedandnotontheHardwareCard.*
13
11
6mm
*
*
X4
*
9
2. Attach Rail Assembly to Frame Assembly
Note:Hardwareispre-installedandnotontheHardwareCard.*
10
3. Connect the Cable and Attach the Console Mast to Frame Assembly
NOTICE:Donot crimp Console Cable.
18
1
12
B
D
G
6mm
X4
11
4. Attach Legs to Frame Assembly
10
16
A
C
G
F
X2
X2
6mm
12
5. Attach Arm Pivot Rod and Lower Handlebar Arms to Frame Assembly
19
3
7
C
G
E
F
X2
X2
13 mm
13
6. Attach Left Pedal to Frame Assembly
NOTICE:RepeatsteponoppositesidewiththeRightPedal(Item17).
F
A
C
G
8
17
C
H
G
A
6mm
14
7. Attach and Adjust the Upper Handlebar Arms to Frame Assembly
Note:Hardwareispre-installedandnotontheHardwareCard.*
MakesuretheUpperHandlebarArmsaresecurebeforeyouexercise.
6mm
20
6
*
*
*
X8
15
8. Attach Handlebar Shrouds to Frame Assembly
Note:Hardwareispre-installedandnotontheHardwareCard.*
15
14
15
14
I
#2
X4
16
9. Route Cables and Attach the Static Handlebar to Frame Assembly
NOTICE:DonotcrimptheConsoleCables.
2
*
X3
6mm
*
*
17
10. Attach Water Bottle Holder to Frame Assembly
Note:Hardwareispre-installedandnotontheHardwareCard.*
4
#2
*
X3
18
12. Connect Cables and Attach Console to Frame Assembly
NOTICE:Aligntheclipsonthecableconnectorsandmakesuretheconnectorslock.Donotcrimp cables.
11. Remove Hardware from Console
NOTICE:Donotcrimpthecable.
Note:Hardwareispre-installedandnotontheHardwareCard.*
5
*
X4
#2
5
*
X4
19
13. Connect the Power Cord to Frame Assembly
21
14. Final Inspection
Inspect your machine to ensure that all hardware is tight and components are properly assembled.
Be sure to record the serial number in the field provided at the front of this manual.
Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s
Manual.
20
Moving the Machine
The machine may be moved by one or more persons depending on their physical abilities and capacities. Make sure that you
and others are all physically fit and able to move the machine safely.
1. Removethepowercord.
2. UsetheTransportHandletocarefullyliftthemachineontothetransportrollers.
3. Pushthemachineintoposition.
4. Carefullylowerthemachineintoposition.
NOTICE:Becarefulwhenyoumovetheelliptical.Allabruptmotionscanaffectthecomputeroperation.
before you Start
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Schwinn 470i Assembly & Owner's Manual

Schwinn
Brand
Schwinn
Model
470i
Category
Spin bikes
Type
Assembly & Owner's Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents