RVi RVi-IPC43-PRO User manual

Brand: RVi

Model: RVi-IPC43-PRO

Category: Security cameras

Type: User manual

This manual is also suitable for

RVi-IPC42Z12

Network video surveillance camera

RVi-IPC42Z12

User’s manual

Please read before using

and save for later use.

www.rvi-cctv.ru

Attention

This symbol indicates that the device has a high voltage. Contact with parts inside

the product is dangerous.

This symbol indicates that the product documentation contains important

instructions for its use or maintenance.

1. Do not install the unit in humid, dusty, or sooty locations. Failure to do so may result in fire or

electric shock.

2. If any unusual smells or smoke come from the unit, stop operation. In this case, immediately

disconnect the power source. Continued use in this condition could cause a fire or electric shock.

3. When a fault is detected in the product, contact your nearest service center. Never disassemble

the product and do not modify its structure. (RVi Company is not responsible for any problems

resulting from changes in product design or as a result of attempted repair products).

4. When cleaning the product, do not expose into the body fluids. This may be a reson of a fire or

electric shock.

Be careful

1. Do not drop any objects on the product and blows to it. Do not install the product in places

with excessive vibration or magnetic interference.

2. Do not install the product in places with high (above 50 ° C) or low (below -40 ° C)

temperatures or high humidity. This can cause a fire or electric shock.

3. If you want to relocate the already installed product to a new location, then before you do so,

turn off the power.

4. During a thunderstorm, it is recommended to disconnect the power supply plug from the AC

line. Otherwise, it may cause fire or damage to the product.

5. Install the product so that the lens is not in direct sunlight and not there heat radiation sources.

7. Do not install the product in front of bright light sources (the sun, welding equipment,

floodlights), as this may cause damage to the light-sensitive sensor imaging.

1. Overview of the device

Fig. 1 the type and size of the device

2. Appointment

IP-camera RVi-IPC42Z12 is designed for broadcast video information to equipment placed on

security office and another storage/preview device.

The basis of the IP camera is the photo detector matrix, the principle of which is based on the

photoelectric conversion sequentially reading the accumulated charges and their subsequent

transfer to the digitizing device / image compression with subsequent broadcast video over data

networks.

The camera has housing with IP66 protection and is designed for outdoor installation.

3. Specification

RVi-IPC43-PRO

Image sensor

1/2.8” CMOS, Progressive scan

Day/Night mode

ICR

Lens

5.1mm-61.2mm(12x optical zoom), Auto iris

Sensitivity

0.01 lk @ F1.2 colour / 0.005 lk @ F1.2 BW

S/N rate

50 dB

Up to 100 m

Resolution, fps

1920x1080, 25 fps

Video comretion

H.264, MJPEG

Audio

1 input/1 output

Video

BNC output

Alarm

1 input/1 output

Network

10Base-T/100Base-TX Ethernet port

Storage

MicroSD up to 64 GB

Network protocols

HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP,

RTSP, RTP, UDP, SMTP, FTP, DHCP, DNS,

DDNS, PPPOE, UPnP, NTP, Bonjour,

SNMPv3, IPFilter, QoS, Multicast, ONVIF

Networks tools

Build in web server. Network client RVi-PSS

for Windows XP и Windows 7, OS Linux, Mac

OS.

Support mobile OS

iOS, Android OS, Windows phone OS

Power

PoE (IEEE802.3af) / DC 12 V (<15 W)

Water/dust protection

IP66

Working temperature

-40°С… +60°С

Weigh

1,3 kg

Dimensions

273х95х95 mm

4. Delivery set

IP camera 1 pcs.

User’s manual 1 pcs.

CD with software 1 pcs.

Mount screws 1 set.

5. Connection

All connectors are located on the main patch cord (see. Fig. 2)

Fig. 2 Patch cord

№п

Наименование

Назначение

Тип

Функция

DC 12V

Connecting a

Power Source

Connector FW-16

RESET

Reset button to

factory settings

Hold down the RESET

button for 5 seconds to reset

the camera to the factory

settings.

I/O

Alarm input /

output

Terminal block with

clamp

Alarm input for receiving a

signal from an external

alarm detector.

LAN

Network port

10Base-T/100Base-

TX Ethernet port

Connected via a standard

Ethernet-cable. Supports the

transfer of power to the

standard PoE.

AUDIO OUT

Audio output port

RCA

Audio output for passive

sound device (eg

headphones).

AUDIO IN

Audio input port

RCA

Audio input from the

microphone.

VIDEO OUT

Analog video

output

BNC

Analogue video output for

display on the test monitor

or any other device capable

to reproduce the analog

video signal.

6. Getting Started

Installation and Setup

Follow the steps described below (see. Fig. 3):

Fig. 3

After mounting the camera on a surface to adjust the angle of the camera (see. Fig. 4), and then

tighten the screw on the camera bracket.

Fig. 4

7. Reset to factory settings

Factory reset by the button located inside the housing of the IPC. Hold the RESET button about

5 seconds, then the camera will reboot.

8. Quick configuration software

Quick configuration software is used to detect the current IP address of the network camera on

the network changes its IP address, but also be used to update the camera firmware. CAUTION!

Some features may be available only on the condition that the IP-camera and a computer that is

running the program on the same subnet.

Run (shortcut "ConfigTool.exe"). The software interface is shown in Figure 5. In the list of

devices (Device list) you can see the IP-address of the devices, the port number, subnet mask,

gateway, the MAC address of the device.

Fig. 5

Selecting one of the IP-addresses in the device list, click on it, right-click, and then open the

context menu, shown in Figure 6

Fig. 6

Selecting "Open Device Web", you will find yourself in Web-based interface of the device where

you will be prompted to log in to access the network device. *

If you want to change the IP-address of the camera without entering the Web-based interface,

you must go to the menu list of devices quick configuration utility. In the menu, the list of

devices (Fig. 6) to select IP-address of the camera, and then double-click to open the interface

"Login" or choose IP-address in the device list and click the "Login" (Fig. 7). Figure 7 displays

the window "Login" which displays the IP-address, user name, password, and port number. Each

parameter can be changed.

Note: The port number must match the TCP port number of the camera installed in the WEB

interface. If the camera is updated in the background, to access it using port 3800, other ports are

not available.

Рис. 7

After login menu will be available for managing network settings of the camera (Fig. 8)

* More Web-based interface described in complete instructions for configuring the network

camera

Fig. 8

In this menu you can configure IP address, date / time, update the firmware.

9. Access to the Web interface of the device

IPC maintains control through a Web interface and through the software on the PC. WEB-

interface allows you to view the camera settings and implement IP-cameras. For network

connection IP-cameras, do the following: - make sure that the IP-camera is physically connected

to the network. - Set the IP-address, subnet mask and gateway of one network for PC and IP-

cameras. In IP-cameras standard address 192.168.1.108, a network mask 255.255.255.0, gateway

192.168.1.1. - To test the connection from the command line, run the command ping

192.168.1.108 (see. Fig. 9)

Fig. 9

Open Internet Explorer and enter the IP-address of the camera in the address bar of your browser.

For example, if the IP-cameras address 192.168.1.108, enter http://192.168.1.108 in the address

bar of Internet Explorer.

When you enter the WEB interface you will withdraw the following - Figure 10. Enter your

username and password. The default username and password admin.

Note: For security reasons, urge to change the username and password when you first log in

WEB interface.

Fig. 10

When you first time connect to the WEB interface, the system message with a proposal to install

a component. Click on the OK button, the operating system will automatically install the

components. If you are unable to automatically install the file ActiveX, check your browser

settings (Tools - Internet Options - Security - Custom Level..).

After a successful login you will be taken to the main window WEB interface.

10. Transport and storage

IPC in transport containers are transported by any kind of covered vehicles (railcars, closed type

holds and compartments of ships, aircraft pressurized heated compartments, etc.) in accordance

with applicable regulations.

11. Disposal

IPC does not pose no danger to human life and health, as well as to the environment after the end

of its life. Disposal of IPC is carried out without taking special measures to protect the

environment.

12. Manufacturer's warranty

 The manufacturer guarantees compliance with IPC technical requirements, subject to

terms of transportation, storage, installation and operation.

 Warranty period - 36 months from the date of sale.

 In the absence of a mark on the date of sale warranty period is calculated from the date

of manufacture

 The warranty is invalid if the cause of the malfunction IPC are:

vandalism;

fire, flood, natural disasters;

accident in the power supply;

electrical breakdown chip electronic board due to an error in the polarity of the power.

 Warranty valid only upon presentation of this manual.

The manufacturer is not responsible and does not cover damage caused by the defects caused by

the fault of the consumer-compliance with the rules of operation and installation.

13. Certificate of acceptance and packaging

Date of manufacture «______» _________________________

Date of sale «______» _____________________________

Seller __________________

SELLER’S

STAMP

RVi RVi-IPC43-PRO User manual

Brand: RVi

Model: RVi-IPC43-PRO

Category: Security cameras

Type: User manual

This manual is also suitable for

RVi-IPC42Z12

Download PDF

report

RVi RVi-IPC43-PRO User manual

This manual is also suitable for

RVi RVi-IPC43-PRO User manual

Other documents