Pelco c3662m User manual

IMPORTANT NOTE

Pelco, Inc. Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: (800) 289-9100 • Fax: (800) 289-9150

International • Tel: +1 (559) 292-1981 • Fax: +1 (559) 348-1120 C3677M (7/08)

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

Due to recent end-of-life motherboard changes, the location of the input/output connectors on the Integral

Digital Sentry

unit’s back panel can vary from the location shown in the Integral Digital Sentry Installation

manual (C3662M) and the quick start guide for this model. These publications are currently being updated

to incorporate the recent changes.

If you need technical assistance with this product, please contact Pelco Product Support at (800) 289-9100

or +1 (559) 292-1981.

INSTALLATION

C3662M (6/08)

Integral Digital Sentry

C3662M (6/08) 3

Contents

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Video Quality Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Typical Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Component Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DS Enterprise SAVR Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DS Xpress (with XMUX2) Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DS XPress (With Internal Camera Inputs) Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DS Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DS 1000 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

DS RealVue XPress Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

DS RealVue Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

DS RealVue RAID Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

XIO Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DS NVR Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

DMS Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

VAU Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

XMUX2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

PTZ Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DS Enterprise Distributed System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Digital Sentry Server/VAU Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Digital Sentry Client/Admin Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Procedural Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Changing a Computer Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Changing an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Changing Passwords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Changing the Startup Mode of a Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Starting and Stopping Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Changing the Time Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Configuring and Testing ODBC Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

System and Display Requirements for Client Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Rules for Caching on Digital Sentry Client Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Renaming DS Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Renaming a DS Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Renaming a VAU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Reconfiguring DSAdmin After an IP Address Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Changing the SA Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Configuring and Verifying Network Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Connecting a Serial Input Device to a DS System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

FlashGuard and the WatchDog Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

FlashGuardTest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Relay Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

DSWatchEventEditor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

RAID IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Isolating Storage Units on a Private Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Configuring the VSANWatchService . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Using the FLTime Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Using XPress WinView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Running WinView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4 C3662M (6/08)

Video Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Switched Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Using Integral License Key Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using RealVue Diagnostic Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Network Health Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Using Digital Sentry Backup Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Backing Up the Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Restoring Archived Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Repairing and Rebuilding a Digital Sentry Database. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Repairing a Restored Database. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Rebuilding Using -fixlocal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Testing a Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Digital Sentry Network Speed Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Checking for Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Running a Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Option #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Option #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Option #3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

After Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Recovering Video Files Without a Database Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Removing References to Local Files on Failed Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Specifications: DS RealVue Desktop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Specifications: DS RealVue RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Specifications: DS RealVue XPress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Specifications: DS 1000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Specifications: DS XPress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Specifications: DS Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Specifications: DS Enterprise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Specifications: DS NVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

C3662M (6/08) 5

List of Illustrations

1 Typical DS Enterprise SAVR or DS XPress System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Typical DS Enterprise Distributed System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3 Rear Panel of DS Enterprise SAVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 DS Enterprise SAVR Audio Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Rear Panel of DS XPress with XMUX2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 DS XPress Audio Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Rear Panel of DS XPress with Internal Camera Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8 DS XPress Audio Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

9 Rear Panel of 9- and 16-Input DS Desktop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

10 Rear Panel of 4-Input DS Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

11 DS Desktop Audio Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

12 Rear Panel of DS 1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

13 DS 1000 Audio Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

14 Rear Panel of DS RealVue XPress. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

15 DS RealVue XPress Audio Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

16 Rear Panel of DS RealVue Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

17 DS RealVue Desktop Alarm Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

18 DS RealVue Desktop Audio Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

19 Rear Panel of DS RealVue RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

20 Rear Panel of DS RealVue RAID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

21 XIO Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

22 Front Panel of XIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

23 Rear Panel of XIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

24 DB-37 Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

25 Rear Panel of DS NVR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

26 Rear Panel of DMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

27 Rear Panel of VAU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

28 VAU Audio Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

29 Rear Panel of XMUX2-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

30 Rear Panel of XMUX2-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

31 XMUX Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

32 DS Enterprise SAVR/DS XPress/VAU PTZ Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

33 DS 1000/RealVue PTZ Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6 C3662M (6/08)

List of Tables

A DS XPress Multicamera Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

B Client Computer System and Display Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

C Watchdog Service Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

D Relay Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

E Network Speed Simulation Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

C3662M (6/08) 7

Important Safety Instructions

Elevated Operating Ambient: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment

may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the

manufacturer’s maximum rated ambient temperature of 32ºC.

Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the

equipment is not compromised.

Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven

mechanical loading.

Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of

the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used

when addressing this concern.

Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply

connections other than direct connections to the branch circuit (for example, use of power strips).

To reduce the risk of fire, use only No. 26 AWG or larger (for example, 24 AWG) UL Listed or CSA Certified Telecommunication Line Cord.

LITHIUM BATTERY; DANGER: The battery should be replaced only by a service technician. The battery is a non-operator-replaceable cell.

There is danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the

manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

RISK OF ELECTRIC SHOCK; DO NOT OPEN: To reduce risk of electric shock, do not remove the cover or back of the DS system. There are

no user-serviceable parts inside. Refer servicing to qualified personnel only.

8 C3662M (6/08)

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC, Class A (All DS models except DS NVR)

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense.

Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this

equipment under Federal Communications Commission’s rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Video Quality Caution

FRAME RATE NOTICE REGARDING USER-SELECTED OPTIONS

Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality

modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the amount of video data stored. The picture

quality can be degraded by either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced resolution

may result in an image that is less clear or even indiscernible. A picture degraded by reducing the picture rate has fewer frames per second,

which can result in images that appear to jump or move more quickly than normal during playback. Lower frame rates may result in a key event

not being recorded by the system.

Judgment as to the suitability of the products for users’ purposes is solely the users’ responsibility. Users shall determine the suitability of the

products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in

a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.

C3662M (6/08) 9

Introduction

This manual is organized into the following sections:

• Typical system configurations: This section illustrates how several types of Integral Digital Sentry

(DS) systems are organized

conceptually.

• Component installation instructions: This section describes how to connect each of the major components of a DS system.

• System-specific installation instructions: This section describes how to configure the components in a DS system. It includes

instructions for naming computers, configuring IP addresses, and connecting video acquisition units (VAU) to the Digital Sentry database.

• Software installation instructions: This section describes how to install Digital Sentry software from two CDs: a Server/VAU

installation CD and a Client/Admin installation CD.

• Procedural instructions: This section covers many individual administrative procedures, such as changing IP addresses and passwords,

configuring network storage, and using Digital Sentry utilities.

TYPICAL SYSTEMS

The following pages illustrate conceptually how several types of DS systems can be connected. Please note that these illustrations cover only a

small percentage of the possible combinations of DS components.

Figure 1. Typical DS Enterprise SAVR or DS XPress System

DS ENTERPRISE SAVR

OR DS XPRESS W/ 64-INPUTS

16-INPUT XMUX

OR XMUX 2

WAN/LAN

STORAGE

SCSI

10 C3662M (6/08)

The server is the centerpiece of a DS system. Separate VAUs can connect to the server through a switch. The server stores large amounts of

video on the optional VSAN storage unit. An optional RS-232 trigger input from an access control system and a digital I/O panel can also be

connected to the server. Refer to Figure 2 for an example of a distributed DS Enterprise system.

Figure 2. Typical DS Enterprise Distributed System

VAU w/ 64-INPUT VAU w/ 64-INPUT

16-INPUT

XMUX OR XMUX 2

KVM SWITCH

VSAN

8 PORT 10/100

NETWORK SWITCH

SCSI

DMS

LAN/WAN

MOUSE

MONITOR

KEYBOARD

C3662M (6/08) 11

Component Installation

NOTE: All DS Enterprise and DS XPress components should be installed only by individuals who have been specifically trained to work with DS

systems. Improper installation by any individual other than a trained technician, or improper installation of unsupported software or hardware,

may automatically void all warranties associated with the DS product.

This section covers the installation of the following Digital Sentry components:

• DS Enterprise SAVR: A combination server and VAU

• DS XPress: A low-cost SAVR with an internal storage option

• DS Desktop: A desktop PC version of DS XPress

• DS 1000: A SAVR with MPEG-4 compression

• DS RealVue XPress: A SAVR with MPEG-4 compression and high resolution images and higher frame rates

• DS RealVue Desktop: A desktop PC version of DS RealVue XPress

• DS RealVue RAID: DS RealVue with an external storage option

• XIO: An external I/O panel included with DS RealVue RAID

• DS NVR: A network video recorder

• DMS: A database management server for enterprise systems with a distributed architecture

• VAU: A video acquisition unit for enterprise systems with a distributed architecture

• XMUX2: Camera input units included with some systems

• PTZ cameras: Cameras with pan/tilt/zoom (PTZ) functionality, connected through RS-232 or RS-422 ports

DS ENTERPRISE SAVR INSTALLATION

To install a DS Enterprise SAVR unit, refer to Figure 3 on page 12 and complete the following steps:

1. Plug the power cord into the power connector

ì.

2. Item î is the COM1 connector, which is used to connect RS-232-based PTZ cameras. Refer to PTZ Installation on page 29 for installation

details.

3. Plug the monitor into the monitor connector ï and its power cord into an electrical outlet.

4. Connect the network port ñ to a network switch using Cat5 cable.

5. Plug the USB mouse into a USB connector ó.

6. Plug the USB keyboard into a USB connector r.

7. Plug a USB printer into a USB connector

8. Plug PC speakers into the line out connector

9. Item

u is the FlashGuard cardlet relay output (bottom two pins), which can be used to trigger an alarm when a critical error occurs. Refer

to FlashGuard and the WatchDog Service on page 40 for details about the relay output. The top four pins in

u are the COM5 connector,

which is used to wire RS-422–based PTZ cameras.

10. Item ~í is an XPress board, which is used to connect to an XMUX2 unit. There is one XPress board for each XMUX2 unit, and the number

of boards varies based on the model number. Refer to the XMUX2 installation instructions for details on connecting the XPress boards to

XMUX2.

11. Item

~â is the audio connector bracket. From top to bottom are audio inputs 1–4, audio outputs 1–4, and four grounds.

12. Item

~ä is an optional SCSI card, which is used to connect to the external storage units.

13. Plug the power cord into an electrical outlet.

14. To provide power to the server, turn on the power switches

~ã.

15. To turn on the server, use the power switches on the front panel of the unit.

12 C3662M (6/08)

Figure 3. Rear Panel of DS Enterprise SAVR

Figure 4. DS Enterprise SAVR Audio Connector

DS XPRESS (WITH XMUX2) INSTALLATION

To install DS XPress with XMUX2, refer to Figure 5 on page 13, and then complete the following steps:

1. Plug the power cord into the power connector

ì.

2. Item î is the COM1 connector, which is used to connect RS-232-based PTZ cameras. Refer to PTZ Installation on page 29 for installation

details.

3. Plug the monitor into the monitor connector ï and its power cord into an electrical outlet.

4. Connect the network port

ñ to the network switch using Cat5 cable.

5. Plug the USB mouse into a USB connector ó.

6. Plug the USB keyboard into a USB connector r.

7. Plug a USB printer into a USB connector s.

8. Plug PC speakers into the line out connector

9. Item

u is the FlashGuard cardlet relay output (bottom two pins), which can be used to trigger an alarm when a critical error occurs.

Connect the alarm to the bottom two pins of the 6-pin terminal block. Refer to the FlashGuard and the WatchDog Service on page 40 for

more details about the relay output. The top four pins in

u are the COM5 connector, which is used to wire RS-422–based PTZ cameras.

GROUND 4

GROUND 3

GROUND 2

GROUND 1

AUDIO OUT 4

AUDIO OUT 3

AUDIO OUT 2

AUDIO OUT 1

AUDIO IN 4

AUDIO IN 3

AUDIO IN 2

AUDIO IN 1

C3662M (6/08) 13

10. Item ~í is the audio connector bracket. From top to bottom are audio inputs 1–4, audio outputs 1–4, and four grounds.

11. Item ~â indicates XPress boards, which are used to connect to XMUX2. DS XPress can contain up to four XPress boards. Refer to XMUX2

Installation on page 28 for details on connecting the XPress boards to XMUX2 units.

12. Item ~ä is an optional SCSI card, which is used to connect to external storage units.

13. Plug the power cord into an electrical outlet and turn on the power switch ~ã .

14. To turn on the system, use the power switch on the front panel of the unit.

Figure 5. Rear Panel of DS XPress with XMUX2

Figure 6. DS XPress Audio Connector

GROUND 4

GROUND 3

GROUND 2

GROUND 1

AUDIO OUT 4

AUDIO OUT 3

AUDIO OUT 2

AUDIO OUT 1

AUDIO IN 4

AUDIO IN 3

AUDIO IN 2

AUDIO IN 1

14 C3662M (6/08)

DS XPRESS (WITH INTERNAL CAMERA INPUTS) INSTALLATION

To install DS XPress with internal camera inputs, refer to Figure 7 on page 15, and then complete the following steps:

1. Plug the power cord into the power connector

ì.

2. Item î=is the COM1 connector, which is used to connect RS-232-based PTZ cameras. Refer to PTZ Installation on page 29 for installation

details.

3. Plug the monitor into the monitor connector

ï and its power cord into an electrical outlet.

4. Connect the network port

ñ to the network switch using Cat5 cable.

5. Plug the USB mouse into a USB connector ó.

6. Plug the USB keyboard into a USB connector r.

7. Plug a USB printer into a USB connector s.

8. Item t shows the connector for the 16 digital inputs and alarm output. Wire your alarm triggers into the input trigger block and connect

the signal ground to a GND pin. Wire an alarm device to AO+ and AO–.

9. Plug PC speakers into the line out connector u.

10. Item ~í is the FlashGuard cardlet relay output (bottom two pins), which can be used to trigger an alarm when a critical error occurs.

Connect the alarm to the bottom two pins of the 6-pin terminal block. Refer to the FlashGuard and the WatchDog Service on page 40 for

more details about the relay output. The top four pins in

u are the COM5 connector, which is used to wire RS-422–based PTZ cameras.

11. Item ~â is the audio connector bracket. From top to bottom are audio inputs 1–4, audio outputs 1–4, and four grounds.

12. Item ~ä is an optional SCSI card, which is used to connect to external storage units.

13. Connect cameras to the camera inputs ~ã. Inputs 17–32 are available only on 32-input systems.

14. The four connectors indicated by ~å are multicamera video outputs. The following table shows how the outputs are used:

15. Plug the power cord into an electrical outlet and turn on the power switch

~ç.

16. To turn on the system, use the power switch on the front panel of the unit.

Table A. DS XPress Multicamera Outputs

DS XPress system Output 1 Output 2 Output 3 Output 4

16 inputs, 1 board 1–16 Unused Unused Unused

16 inputs, 2 boards 1–8 9–16 Unused Unused

16 inputs, 4 boards 1–4 5–8 9–12 13–16

32 inputs, 2 boards 1–16 17–32 Unused Unused

32 inputs, 4 boards 1–8 9–16 17–24 25–32

C3662M (6/08) 15

Figure 7. Rear Panel of DS XPress with Internal Camera Inputs

NOTE: The top row of camera inputs is included only on 32-input systems.

Figure 8. DS XPress Audio Connector

INPUT 32INPUT 31INPUT 30INPUT 29INPUT 28INPUT 27INPUT 26INPUT 25

INPUT 24INPUT 23INPUT 22INPUT 21INPUT 20INPUT 19INPUT 18INPUT 17

INPUT 16INPUT 15INPUT 14INPUT 13INPUT 12

OUTPUT4OUTPUT3OUTPUT2OUTPUT1

INPUT 11INPUT 10INPUT 9

INPUT 8INPUT 7INPUT 6INPUT 5INPUT 4INPUT 3

INPUT 2INPUT 1

GROUND 4

GROUND 3

GROUND 2

GROUND 1

AUDIO OUT 4

AUDIO OUT 3

AUDIO OUT 2

AUDIO OUT 1

AUDIO IN 4

AUDIO IN 3

AUDIO IN 2

AUDIO IN 1

16 C3662M (6/08)

DS DESKTOP INSTALLATION

To install DS Desktop, refer to Figure 9 for 9-input or 16-input systems, or Figure 10 for 4-input systems, and then complete the following steps:

1. Plug the power cord into the power connector

ì.

2. Plug a monitor into a monitor connector î and its power cord into an electrical outlet. The top connector is for a VGA monitor, and the

bottom connector is for a DVI monitor.

3. Plug the USB keyboard into a USB connector

ï.

4. Plug the USB mouse into a USB connector

ñ.

5. Plug a USB printer into a USB connector ó.

6. Connect the network port r to a network switch using Cat5 cable.

7. Plug PC speakers into the line out connector s.

8. Item t is the COM5 connector, which is used with RS-422 PTZ cameras. Refer to PTZ Installation on page 29 for installation details.

9. Item

u is the audio connector bracket. From top to bottom are audio inputs 1–4, audio outputs 1–4, and four grounds.

10. Item

~í shows the connector for the 16 digital inputs and alarm output. Wire your alarm triggers into the input trigger block and connect

the signal ground to a GND pin. Wire an alarm device to AO+ and AO–.

11. Item ~â is a multicamera video output that can be connected to an analog monitor.

12. Connect cameras to the camera inputs ~ä.

13. Select the correct input voltage for your area using the input voltage switch ~ã.

14. Plug the power cord into an electrical outlet and turn on the power switch ~å .

15. To turn on the server, use the power switch on the front panel of the unit.

Figure 9. Rear Panel of 9- and 16-Input DS Desktop

NOTE: The number of camera input BNCs varies based on the model number.

INTPUT 14 INTPUT 15 INTPUT 16 OUTPUT 1INPUT 13

INPUT2INTPUT1

INPUT 10INPUT 9INPUT 8INPUT 7

INPUT 6INPUT 5INPUT 4INPUT 3

INPUT 2INPUT 1

115

C3662M (6/08) 17

Figure 10. Rear Panel of 4-Input DS Desktop

Figure 11. DS Desktop Audio Connector

DS 1000 INSTALLATION

To install DS 1000, refer to Figure 12 on page 18, and then complete the following steps:

1. Plug the power cord into the power connector

ì.

2. Plug a monitor into a monitor connector

î and its power cord into an electrical outlet. The top connector is for a VGA monitor, and the

bottom connector is for a DVI monitor.

3. Plug the USB keyboard into a USB connector

ï.

4. Plug the USB mouse into a USB connector ñ.

5. Plug a USB printer into a USB connector ó.

6. Plug PC speakers into the line out connector

7. Item s is a SCSI card, which is used to connect to the VSAN external storage units. A chain of up to four VSAN units can be connected to

the SCSI card.

8. Item t is the audio connector bracket. From top to bottom are audio inputs 1–4, ground, audio inputs 5–8, ground, audio inputs 9–12,

ground, audio inputs 13–16, ground.

9. Connect one or both of the network ports u to a network switch, IP cameras, and so forth using Cat5 cable.

OUTPUT

INPUT 4

INPUT 3

INPUT 2

INPUT 1

115

GROUND 4

GROUND 3

GROUND 2

GROUND 1

AUDIO OUT 4

AUDIO OUT 3

AUDIO OUT 2

AUDIO OUT 1

AUDIO IN 4

AUDIO IN 3

AUDIO IN 2

AUDIO IN 1

18 C3662M (6/08)

10. Item ~í is the COM5 connector, which is used to connect RS-422 PTZ cameras. Refer to PTZ Installation on page 29 for installation details.

11. Item ~â shows the connector for the 16 digital inputs and alarm output. Wire your alarm triggers into the input trigger block and connect

the signal ground to a GND pin. Wire an alarm device to AO+ and AO–.

12. Connect cameras to the camera inputs=~ä. Inputs 17–32 (the top row of BNC connectors) are available only on 32-input systems.

13. Plug the power cord into an electrical outlet and turn on the power switch ~ã .

14. To turn on the server, use the power switch on the front panel of the unit.

Figure 12. Rear Panel of DS 1000

Figure 13. DS 1000 Audio Connector

GROUND 4

AUDIO IN 16

AUDIO IN 15

AUDIO IN 14

AUDIO IN 13

GROUND 3

AUDIO IN 12

AUDIO IN 11

AUDIO IN 10

AUDIO IN 9

GROUND 2

AUDIO IN 8

AUDIO IN 7

AUDIO IN 6

AUDIO IN 5

GROUND 1

AUDIO IN 4

AUDIO IN 3

AUDIO IN 2

AUDIO IN 1

C3662M (6/08) 19

DS REALVUE XPRESS INSTALLATION

To install DS RealVue XPress, refer to Figure 14 on page 19, and then complete the following steps:

1. Plug the power cord into the power connector

ì.

2. Item î is the COM1 connector, which is used to connect RS-232 PTZ cameras. Refer to PTZ Installation on page 29 for installation details.

3. Plug a monitor into the monitor connector ï and its power cord into an electrical outlet.

4. Plug the USB keyboard into a USB connector ñ.

5. Item ó shows the connector for the 16 digital inputs and alarm output. Wire your alarm triggers into the input trigger block and connect

the signal ground to a GND pin. Wire an alarm device to AO+ and AO–.

6. Plug the USB mouse into a USB connector r.

7. Plug a USB printer into a USB connector s.

8. Item t is the COM5 connector, which is used to connect RS-422 PTZ cameras. Refer to PTZ Installation on page 29 for installation details.

9. Plug PC speakers into the line out connector

10. Item

~í is an optional SCSI card, which is used to connect to the external storage units.

11. Connect one or both of the network ports ~â to a network switch, IP cameras, and so forth using Cat5 cable.

12. Item ~ä is the audio connector bracket. From top to bottom are audio inputs 1–4, ground, audio inputs 5–8, ground, audio inputs 9–12,

ground, audio inputs 13–16, ground.

13. Connect cameras to the camera inputs ~ã. Inputs 17–32 (the top row of BNC connectors) are available only on 32-input systems. Inputs

9–16 are visible but cannot be used on 8-input systems.

14. The four connectors indicated by ~å are multicamera video outputs.

15. Plug the power cord into an electrical outlet and turn on the power switch ~ç .

16. To turn on the server, use the power switch on the front panel of the unit.

Figure 14. Rear Panel of DS RealVue XPress

NOTE: The top row of camera inputs is included only on 32-input systems. Inputs 9-16 are visible but cannot be used on 8-input systems.

INPUT 32INPUT 31INPUT 30INPUT 29INPUT 28INPUT 27INPUT 26INPUT 25

INPUT 24INPUT 23INPUT 22INPUT 21INPUT 20INPUT 19INPUT 18INPUT 17

INPUT 16INPUT 15INPUT 14INPUT 13INPUT 12

OUTPUT4OUTPUT3OUTPUT2OUTPUT1

INPUT 11INPUT 10INPUT 9

INPUT 8INPUT 7INPUT 6INPUT 5INPUT 4INPUT 3

INPUT 2INPUT 1

Page is loading ...

Pelco c3662m User manual

Related papers

Other documents