FASTEN-PRO Three_Way Tacker Staple Gun Kit User manual

Brand: FASTEN-PRO

Model: Three_Way Tacker Staple Gun Kit

Category: Staple guns

Type: User manual

This manual is also suitable for

96755

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

REV 14g

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures� Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number)�

Keep this manual and the receipt in a safe and dry place for future reference�

When unpacking, make sure that the product is intact

and undamaged� If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible�

2014 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools�

Diagrams within this manual may not be drawn proportionally� Due to continuing

improvements, actual product may differ slightly from the product described herein�

Tools required for assembly and service may not be included�

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 96755

SAFETY OPERATION MAINTENANCESETUP

Table of Contents

Safety ��3

Specifications ��5

Setup ��6

Operation ��7

Maintenance ��8

Parts List and Diagram ��10

Warranty ��12

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol� It is used to alert you to

potential personal injury hazards� Obey all safety messages

that follow this symbol to avoid possible injury or death�

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury�

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury�

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury�

Addresses practices not related to personal injury�

Page 3For technical questions, please call 1-888-866-5797.Item 96755

SAFETYOPERATIONMAINTENANCE SETUP

IMPORTANT SAFETY INFORMATION

General Power Tool Safety Warnings

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term ″power tool″ in the warnings refers to your power tool.

Work Area Safety

1� Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

2� Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which

may ignite the dust or fumes.

3� Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

Personal Safety

1� Stay alert, watch what you are doing

and use common sense when operating

a Tool. Do not use a Tool while

you are tired or under the influence

of drugs, alcohol or medication.

A moment of inattention while operating

Tools may result in serious personal injury.

2� Use personal protective equipment.

Always wear eye protection. Safety

equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

3� Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the

Tool in unexpected situations.

4� Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long

hair can be caught in moving parts.

5� Only use safety equipment

that has been approved by an

appropriate standards agency.

Unapproved safety equipment may

not provide adequate protection.

Eye protection must be ANSI-approved

and breathing protection must be

NIOSH-approved for the specific

hazards in the work area.

Page 4 For technical questions, please call 1-888-866-5797. Item 96755

SAFETY OPERATION MAINTENANCESETUP

Power Tool Use and Care

1� Do not force the Tool. Use the correct

Tool for your application. The correct Tool

will do the job better and safer at the

rate for which it was designed.

2� Store Tools out of the reach of children

and do not allow persons unfamiliar

with the Tool or these instructions to

operate the Tool. Tools are dangerous

in the hands of untrained users.

3� Maintain Tools. Check for misalignment

or binding of moving parts, breakage

of parts and any other condition that

may affect the Tool’s operation. If

damaged, have the Tool repaired

before use. Many accidents are

caused by poorly maintained Tools.

4� Keep Tools clean. Properly

maintained Tools are less likely to

bind and are easier to control.

5� Use the Tool, accessories and Tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work

to be performed. Use of the Tool for

operations different from those intended

could result in a hazardous situation.

6� Stay alert. Watch what you are

doing, and use common sense

when operating the Staple Gun.

7� Use clamps (not included) or other

practical ways to secure and support the

workpiece to a stable platform. Holding

the work by hand or against your body is

unstable and may lead to loss of control.

8� Never aim the Staple Gun at any

person, child or animal.

9� Use only accessories that are

recommended by the manufacturer

for your model. Accessories that may

be suitable for one product may become

hazardous when used on another product.

10� When servicing a product, use only

identical replacement parts. Follow

instructions in the “Inspection,

Maintenance, And Cleaning” section of

this manual. Use of unauthorized parts or

failure to follow maintenance instructions

may create a risk of electric shock or injury.

11� Maintain labels and nameplates on the

Tool.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

12� Do not leave the Tool unattended.

13� This product is not a toy.

Keep it out of reach of children.

14� The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur�

It must be understood by the operator that

common sense and caution are factors

which cannot be built into this product,

but must be supplied by the operator�

Service

Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

SAVE THESE INSTRUCTIONS.

Page 5For technical questions, please call 1-888-866-5797.Item 96755

SAFETYOPERATIONMAINTENANCE SETUP

Specifications

Stapler

Dimensions

6-5/16” x 5-1/2” W x 1-3/16” diameter

Trigger Palm Squeeze type

Fastener Types

Included

Standard staples, brad nails

and U-shaped staples

Magazine Spring loaded slide strip

List of Contents

Part(s) Description Qty

Staple Gun 1

Standard Staples (500) T50, 3/8" crown x 5/16" L 500

Brad Nails (500) 3/8" 500

U-Shaped Staples (500) 1/4” crown x 1/2" L 500

Page 6 For technical questions, please call 1-888-866-5797. Item 96755

SAFETY OPERATION MAINTENANCESETUP

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under

subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following

pages, refer to Parts List and Diagram on page 10�

Functions

Depth Adjustment Knob

Handle

Staple Channel Latch

Nose

Figure A

Page 7For technical questions, please call 1-888-866-5797.Item 96755

SAFETYOPERATIONMAINTENANCE SETUP

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under

subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following

pages, refer to the Assembly Diagram near the end of this manual�

1� Push the End Clip forward and down to

release the Staple Channel Latch� Pull

out the Staple Channel� See figure A�

2� Load the staples or brad nails into the

Staple Channel� Each of the fasteners

is to be loaded into the Staple Channel

with its sharp end facing the base of

the Staple Channel� See figure B�

3� Staples are to be inserted into the center of

the Staple Channel as shown in figure B�

Brad nails are to be inserted on either side

of the Staple Channel, as in figure B, but not

placed in the center of the Staple Channel�

4� To adjust force that will be exerted on the

fastener to drive it deeper into the work piece,

use the Depth Adjustment Knob located at

the top of the Staple Gun� See Figure A�

5� Turn the Depth Adjustment Knob

clockwise to increase the force to drive

the fastener, and counterclockwise

for less force driving the fastener�

Push in and down to

release the Staple

Channel Latch�

Figure B

Standard

staple

U-Shaped

staple

Brad

Figure C

Workpiece and Work Area Set Up

1� Designate a work area that is clean

and well-lit� The work area must not

allow access by children or pets to

prevent distraction and injury�

2� Secure loose workpieces using a

vise or clamps (not included) to

prevent movement while working�

3� There must not be objects, such

as utility lines, nearby that will

present a hazard while working�

Page 8 For technical questions, please call 1-888-866-5797. Item 96755

SAFETY OPERATION MAINTENANCESETUP

General Operating Instructions

1� Push the End Clip forward and down to

release the Staple Channel latch� Pull

out the Staple Channel� See Figure B�

2� Insert a full strip of fasteners into the Staple

Channel� Push the Staple Channel back

into the Staple Gun Body� Make certain

that it is pushed all the way back into

place before operating the Staple Gun�

3� Determine whether or not the object

being stapled will necessitate extra force

from the Staple Gun� This will depend

primarily on the thickness of the item

being stapled� For instance, a large pad

of papers will need more force than one

or two sheets being stapled together�

4� Set the Depth Adjustment Knob accordingly�

5� Place the item to be stapled below the Driver

located on the front of the Staple Gun� Grasp

the Staple Gun with your fingers inserted

into the opening in the Housing and your

palm resting on the Handle� Squeeze and

pull down on the Handle to fire a fastener�

7� Test the Staple Gun using a scrap work

piece� Make certain that you have the Depth

Adjustment Knob set correctly, and that

the fasteners are placed as you desire�

8� To prevent accidents, clean, then store

the tool indoors out of children’s reach�

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration

occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1� BEFORE EACH USE, inspect the general

condition of the tool� Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation�

2� AFTER USE, wipe external surfaces

of the tool with clean cloth�

3� Remove dirt and debris from the Staple

Gun using a clean, soft cloth� Do not

use flammable corrosive or abrasive

solvents to clean the Staple Gun�

Cleaning and Removing the Staple Channel

1� Push the Retaining Clip at the front of

the Staple Gun forward to release the

Staple Channel� Pull the two tabs (located

midpoint on the bottom of the Staple Gun)

toward the back of the Staple Gun�

2� The Staple Channel is now free of

the Staple Gun and can be cleared

of any jammed fasteners�

Page 9For technical questions, please call 1-888-866-5797.Item 96755

SAFETYOPERATIONMAINTENANCE SETUP

Troubleshooting

Problem Possible Causes Possible Solutions

Staple Gun

does not staple

1� Staples not loaded correctly�

2� Magazine Unit not fully

and properly inserted

into Staple Gun�

3� Lever not pulled completely up

and then fully pressed down�

1� Verify that staples are loaded

into the Magazine Unit flat and

with prongs facing upward�

2� Check that Magazine Unit

is fully inserted�

Stapler jams

during operation

Staples jammed in channel� 1� Pull out the Staple Channel�

2� Remove jammed fasteners from

the channel� You may need to use

long-nosed pliers (not included)�

3� Make certain that you are using

correct size fasteners�

4� Replace Staple Channel�

Follow all safety precautions whenever diagnosing or servicing the tool.

Page 10 For technical questions, please call 1-888-866-5797. Item 96755

SAFETY OPERATION MAINTENANCESETUP

Part Description Qty

1 Depth Adjustment Knob 1

2 Handle 1

3 Handle Ring 1

4 Staple Channel 1

5 Staple Tab 1

6 Staple Channel Latch 1

7 Retaining Clip 1

8 Housing 1

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND

ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY� NEITHER THE

MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY

OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS

TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF

THE PRODUCT� IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN

BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER� THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS

TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING

OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO�

Parts List

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead�

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts�

Page 11For technical questions, please call 1-888-866-5797.Item 96755

SAFETYOPERATIONMAINTENANCE SETUP

Assembly Diagram

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co� makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase� This

warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or

accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance� We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product� Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to

you� THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS�

To take advantage of this warranty, the product or part must be returned to us with

transportation charges prepaid� Proof of purchase date and an explanation of the complaint

must accompany the merchandise� If our inspection verifies the defect, we will either repair or

replace the product at our election or we may elect to refund the purchase price if we cannot

readily and quickly provide you with a replacement� We will return repaired products at our

expense, but if we determine there is no defect, or that the defect resulted from causes not

within the scope of our warranty, then you must bear the cost of returning the product�

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state�

FASTEN-PRO Three_Way Tacker Staple Gun Kit User manual

Brand: FASTEN-PRO

Model: Three_Way Tacker Staple Gun Kit

Category: Staple guns

Type: User manual

This manual is also suitable for

96755

Download PDF

report

FASTEN-PRO Three_Way Tacker Staple Gun Kit User manual

This manual is also suitable for

FASTEN-PRO Three_Way Tacker Staple Gun Kit User manual

Related papers

Other documents