Honda ACCORD 08E51-SDA-100 Owner's manual

Brand: Honda

Model: ACCORD 08E51-SDA-100

Category: Car alarm

Type: Owner's manual

This manual is also suitable for

08E55-SDA-100

Honda ACCORD 08E51-SDA-100 is a security system that offers various features to enhance your vehicle's protection and convenience. With its programmable microprocessor, it monitors your vehicle for optimal security and can be tailored to your preferences.

The system includes a main unit and a remote control transmitter, enabling you to arm and disarm the system from outside the vehicle. The remote control also allows you to activate the panic function in case of an emergency, intentionally sounding the horn to deter potential threats.

Security System Owner’s Manual

Kit No. 08E51-SDA-100

08E55-SDA-100

ACCORD

Contents

Introduction ..................................................... 3

Emergency Disarming

Disarming .................................................. 4

During the Panic Alarm Activation............. 4

During the Entry Delay Time ..................... 5

System Controls

Arming Mode (MANUAL

AUTOMATIC) ....

Arming Mode (AUTOMATIC

MANUAL) ....

Valet (Automatic Arming Mode only)

Placing the System in the Valet Mode ....... 8

In the Valet Mode....................................... 9

Exit From the Valet Mode ........................ 10

Arming

Arming Methods ...................................... 11

Manual Arming (Remote Controlled) ...... 11

Automatic Arming (Passive) .................... 12

Alarm Mode

Alarm Triggered Mode ............................. 13

Disarming

Remote Control Disarming ...................... 14

Panic (Only vehicles not equipped with Standard

Keyless Entry System)

Activating the Panic Function .................. 15

Deactivating the Panic Function .............. 16

Deactivating the Panic Function (When the

panic function comes into operation during

the alarm duration) .................................. 16

Tripped Sensor Warning and Indication

Tripped Sensor Warning .......................... 17

Tripped Sensor Indication ........................ 18

Remote Control Transmitter (Only vehicles not

equipped with Standard Keyless Entry System)

Battery Replacement ............................... 19

Remote Control Code Programming (Only vehicles

not equipped with Standard Keyless Entry System)

How to Program Remote

Control Transmitters ................................ 20

Optional Items ............................................... 23

Glossary ........................................................ 24

Specifications ................................................ 26

Please write the serial number of the remote control and the main unit belo

Keep this booklet as a record of your purchase.

Remote Control No.:

Main Unit No.:

Introduction

Congratulations on your purchase of this Honda Secur

ity System.

Your Honda Security System is the product of years of research

and development. It will give you many years of reliab

performance, protection, and convenience.

The system consists of two major components: a main unit and

a remote control transmitter.

The main unit is the brain of the system. The built-in

programmable microprocessor monitors your vehicle f

or optimal

protection. The Security System also offers various options to

tailor the system to the preferences of different users

The remote control allows you to turn the system on and off

from outside the vehicle while simultaneously locking and

unlocking the doors

. The transmitter can also be used to

intentionally activate the horn in case of an emergency

To take full advantage of your Honda Security System, w

encourage you to read this manual thoroughly.

Due to the expertise required to properly install the Honda

Security System, we highly recommend that the installation be

performed by your Honda dealer. Proper wiring and component

placement are essential for optimum system perfor

mance.

The Security System can be operated with the vehicle’

s Keyless Entry System.

For operation of the Keyless Entry System, refer to the v

ehicle Owner’s Manual.

Only on vehicles equipped with power door locks.

During the Panic

Alarm Activation

Emergency Disarming

Enter the vehicle and insert the ignition key.

Disarming

• The system can be disarmed using the ignition ke

y regardless of the method used to

arm the system.

• This method of disarming also serves as an emergency o

verride if the remote

control transmitter cannot be used.

LOCK

Status LED

Turn the ignition key to the ON (II) position.

The security system disarms and alarming stops when the ignition k

ey is turned to

the ON (II) position. Check to see the status LED goes off

Turn the ignition key to the ON (II) position.

The system stops the panic alarming when the ignition k

ey is turned to the ON (II)

position. Check to see the status LED goes off.

LOCK

Status LED

Emergency Disarming

During the Entry Delay

Time

• When the system is being armed by the AUTOMA

TIC arming method, there is a

20-seconds entry delay time after opening a door

• If the system is armed by the remote control transmitter

, the entry delay time is set

to 0 seconds, and the alarm is triggered immediately when a door is opened.

LOCK

To disarm the entry delay time mode, insert the ignition k

ey after opening the door.

Turn the ignition key to the ON (II) position. The secur

ity system disarms when the

ignition key is turned to the ON (II) position.

The switching procedure is

The result

MANUAL MODE

Not completed No beep

AUTOMATIC MODE

Completed Beep once

NOTE: Steps 1 thru 5 must be completed within 5 seconds.

Arming Mode

(MANUAL

AUTOMATIC)

This section explains how to change the arming mode from MANU

AL to AUTOMATIC.

NOTE:

The arming mode of the Security System is preset to MANU

AL arming.

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

ay out)

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

ay out)

Insert the ignition key.

Observe that the system beeps

once.

within 5 seconds

System Controls

Insert the ignition key.

Observe that the system beeps

twice.

The switching procedure is

The result

AUTOMATIC MODE

Not completed No beep

MANUAL MODE

Completed Beep twice

System Controls

Turn the ignition key from the ON (II) position to the LOCK (0) position.

Remove the key from the ignition switch.

Arming Mode

(AUTOMATIC

MANUAL)

This section explains how to change the arming mode from A

UTOMATIC to MANUAL.

Open a door and close it. (The EXIT delay starts.)

NOTE: Steps 3 thru 7 must be completed within 5 seconds.

Insert the ignition key.

Remove the ignition key from the ignition switch. (All the w

ay out)

Insert the ignition key.

Remove the ignition key from the ignition switch.

(All the way out)

LOCK

within 5 seconds

Placing the System in the Valet Mode

(Valet Mode cannot be used in the

Manual Arming Mode)

• When the security system is placed in the valet mode, it is tempor

arily

placed on hold. When in the valet mode, the system cannot be ar

med,

but panic mode is still functional. This is a convenient feature if the car

is to be washed, serviced, or valet parked.

• Before removing the ignition key, the door opening or closing is not

related to set valet mode.

Remove the ignition key from the ignition switch.

Press the UNLOCK button on the remote control tr

ansmitter three times.

The Status LED flashes once, indicating that the system is in the

Valet mode.

Valet (Automatic Arming Mode only)

NOTE: Steps 1 and 2 must be completed within 5 seconds.

Status LED

Exit the vehicle and close the door.

within 5 seconds

Valet (Automatic Arming Mode only)

In the Valet Mode:

Open one of the doors.

The Status LED blinks once.

After turning the ignition switch to LOCK (0), remove the ignition k

ey.

The Status LED blinks once.

If you follow either procedure below, the Status LED blinks once to show

the system is in the Valet mode.

Status

LED

Status

LED

Keyless/Security during the Valet Mode.

Lock/Unlock of Keyless

Panic of Keyless

Set/Unset of Security

VALET MODE is ON Active

Active

Non-Active

VALET MODE is OFF Active

Active

Valet (Automatic Arming Mode only)

Exit From the Valet Mode

With the system in the Valet mode, take the key out of the ignition s

witch.

Press the UNLOCK button on the remote control transmitter

Observe that the Status LED flashes twice, indicating that the system is out of the

Valet mode.

The system is now in the Disarm mode.

Status LED

Arming

Arming Methods

There are two possible ways to arm the system:

• MANUAL Arming (Remote Control)

• AUTOMATIC Arming (Passive)

Manual Arming

(Remote Controlled)

Make sure the arming mode is set to

MANUAL.

Turn the ignition key to the LOCK (0) position.

Remove the key from the ignition switch.

Exit the vehicle, then close all the doors, the

trunk, and the hood

Press the LOCK button on the remote control

transmitter. Observe that:

• The remote control LED illuminates.

• The security system arms.

• The status LED flashes once per 3

seconds. (Be sure to check the status LED

flashes.)

• The parking lights flash once. (Be sure to

check that the lights flash.)

• The doors lock

If the LOCK button is pressed a second time

(within 5 seconds of the first push) the horn

beeps once to confirm the doors are locked

and the system is armed.

Only on the vehicles equipped with optional hood switch.

Only on the vehicles equipped with power door locks

• When the main unit is set to MANUAL, the system is ar

med by using the remote

control transmitter. This is the factory setting.

• The system beeps three times, and does not arm if the tr

unk, any door, or the

hood

is not closed when the LOCK button is pressed.

• When the main unit is set to AUTOMATIC, the system ar

ms automatically 20 seconds

after the last door, the trunk, or the hood

is closed

• If a door, the trunk or the hood

is opened during the 20 seconds exit delay time, the timer resets

and the 20 seconds exit delay time restarts after the last door, the tr

unk, or the hood

is closed.

• If the ignition key is inserted into the ignition switch dur

ing the exit delay time, the system

will be disarmed.

• The system beeps three times and does not arm if the tr

unk, any door, or the hood

not closed when the LOCK button is pressed.

•

When the remote control transmitter is used to arm the system in the auto ar

ming

mode, the 20 seconds entry and exit delay time is changed to 0 seconds

Arming

Make sure the arming mode is set to AUTOMATIC.

Automatic Arming

(Passive)

(Arms the security system without

locking the doors.)

Turn the ignition key from the ON (II) position to the LOCK (0) position.

Remove the key from the ignition switch.

The system arms automatically 20 seconds after the last door

, the trunk, or the hood

closed. Observe that:

• The status LED flashes four times per second during the e

xit delay time, and once per 3

seconds after the system is armed. (Be sure to check that the status LED flashes

• The parking lights flash once without a beep to confirm the system is ar

med.

(Be sure to check that the lights flash.)

NOTE: When the LOCK button on the remote control transmitter is pressed dur

ing the

exit delay time, the arming function of the remote control tr

ansmitter has priority.

Exit the vehicle, and close all the doors, the trunk, and the hood

OFF

Only on the vehicles equipped with optional hood switch.

The ignition key must be removed from the ignition s

witch before the system will arm.

20-sec exit delay time

Alarm Mode

Alarm Triggered Mode

• After the system is armed, opening of any doors, the tr

unk or the hood

, or breaking

of window glass will trigger the alarm.

• If the door(s) are kept open, the alarm will continue to sound f

or 5 minutes.

• If the battery is disconnected in the alarm mode, any attempt to reconnect the

battery will send the alarm into the triggered mode.

Only on the vehicles equipped with optional hood switch.

When the alarm is triggered, observe

that:

• The horn sounds once per 1.5

seconds for one alarm duration (horn

duration is 30 seconds).

• The parking lights flash once per 1.5

seconds for one alarm duration

(parking lights duration is 30

seconds).

• The status LED flashes twice per

second for one alarm duration.

• After one alarm duration, the system

automatically rearms.

NOTE: The entry delay time is

functional only when the arming mode

is set to AUTOMATIC and the door is

open.

Press the UNLOCK button of the

remote control transmitter to cancel the

alarm, and the system disarms.

Disarming

Remote Control

Disarming

• Regardless of the method used to arm the system, the system can be disar

med

using the remote control transmitter.

Only on vehicle equipped with power door locks.

Press the UNLOCK button once on the

remote control transmitter.

Observe that:

• The remote control LED illuminates.

• The security system disarms and the

parking lights flash twice when the

alarm has not been triggered.

If the alarm has been triggered, the

horn sounds four times to tell you the

alarm has been triggered.

• The doors unlock

NOTE:

After being disarmed, the

system will rearm in 30 seconds if the

doors are not opened.

Panic (Only vehicles not equipped with Standard Keyless Entry System)

Activating the Panic

Function

Press and hold the PANIC button for

more than 1 second. Observe that:

• The horn sounds once per 1.5

seconds for one alarm duration (horn

duration is 30 seconds).

• The parking lights flash once per 1.5

seconds for one alarm duration

(parking light duration is 30 seconds).

• The status LED flashes twice per

second for one alarm duration.

• You can intentionally activate the horn and flash the par

king lights by the remote

control transmitter.

• This feature is designed to attract attention in case of an emergency

• This function works only when the iginition key is turned to the loc

k (0) and

ACCESSORY (I), and when it is removed from the iginition s

witch.

11111111111111111111111111111111

Panic (Only vehicles not equipped with Standard Keyless Entry System)

To stop the horn sounding and the

parking lights flashing before the alarm

duration time is up, press the PANIC,

LOCK or UNLOCK button momentarily,

or turn the ignition key to the ON (II)

position.

Deactivating the Panic Function

LOCK

1111111111111111111111111111111

To stop the panic function before the

alarm duration time is up, press the

UNLOCK button twice.

Deactivating the Panic Function

(When the panic function comes into operation during the alarm duration)

1111111111111111111111111111111

Tripped Sensor Warning and Indication

Tripped Sensor Warning

• The system will warn you that the security system has been tr

ipped in your absence.

If the system was tripped and automatically rearmed, obser

ve that:

• The horn sounds four times when the system is disar

med.

Example 1:

If opening the trunk causes the alarm to be triggered, the Status LED will flash tw

times, pause and repeat this sequence for 1 minute.

Example 2:

If the alarm is triggered twice, first by opening the door and then b

y opening the trunk,

the Status LED will flash once, pause, flash two times

, pause and repeat this sequence

for 1 minute.

TRIPPED

STATUS LED

SENSOR

NUMBER OF FLASHES

Door

Trunk

Ignition Key Switch

Ignition Switch

Battery Disconnected

Glass Breakage

Hood

Tripped Sensor Indication

• After disarming the system, if the tripped sensor w

arning indicator appears, you can

identify which portion of the security system has been tr

ipped by observing the

number of flashes as shown below.

• Information regarding the security system can be retr

ieved from the memory of the

systems main control unit.

Insert the ignition key.

Within 1 second after step 2, open the door.

Tripped Sensor Warning and Indication

Disarm the security system.

Close the door.

Within 1 second after step 3, remove the key from the ignition s

witch.

The status LED flashes to indicate which sensor(s) w

ere tripped.

Remote Control Transmitter (Only vehicles not equipped with Standard Keyless Entry System)

Battery Replacement

• The remote control transmitter requires one lithium batter

y (CR2025).

Using a coin turn the battery cover countercloc

kwise and remove the cover from the

remote control transmitter.

Remove the battery. Install the new battery with the proper polar

ity as shown.

NOTE: If the battery is incorrectly installed, the remote control tr

ansmitter can be

damaged.

Replace the battery cover. Use a coin to turn it cloc

kwise and lock the cover.

Remote Control Code Programming (Only vehicles not equipped with Standard Keyless Entry System)

How to Program Remote

Control Transmitters

• For steps 2 thru 12, each step must be completed within 5 seconds

. Step 13 must be

completed within 10 seconds for each remote.

• Up to three remotes can be stored in memory.

• All remotes to be programmed must be on hand.

• A non-programmed remote will work for this procedure

• Turn the ignition key to the LOCK (0) position to complete the prog

ramming procedure.

Disarm the security system.

Turn the ignition key to the ON (II)

position.

Press the LOCK or UNLOCK button on

the remote control transmitter.

Turn the ignition key to the LOCK (0)

position.

Turn the ignition key to the ON (II)

position.

LOCK

Page is loading ...

Honda ACCORD 08E51-SDA-100 Owner's manual

Brand: Honda

Model: ACCORD 08E51-SDA-100

Category: Car alarm

Type: Owner's manual

This manual is also suitable for

08E55-SDA-100

Download PDF

report

Honda ACCORD 08E51-SDA-100 Owner's manual

This manual is also suitable for

Honda ACCORD 08E51-SDA-100 Owner's manual

Related papers

Other documents