Sony XR-3304 Installation guide
- Category
- Motorcycle Accessories
- Type
- Installation guide
SONY XR-3304 (E,Ar) 3-000-000-21 (1)
Installation
Precautions
• Choose the installation location carefully so that the unit will not hamper the driver during driving.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or
hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.
• Use only the supplied mounting hardware for a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
How to Detach and Attach the Front Panel
Before installing the unit, detach the front panel.
To detach
Press the RELEASE button to open up the front panel, then pull it out. Then slide the front panel a little to
the left, and pull it off towards you.
To attach
Align the parts A and B, and push the front panel until it clicks.
3-858-022-21 (1)
Installation/Connections
###/###
Sony Corporation 1996 Printed in Singapore
XR-3304
FM/MW/SW
Cassette Car
Stereo
To detach
###
RELEASE button
###
B
A
12
3
Mounting Example
Installation in the dashboard
Bend these claws, if necessary.
#####
Fire wall
###
Dashboard
###
2
3
Mounting the Unit in a Japanese Car
This unit may not be installed in some makes of cars. In this case, consult your nearest Sony dealer.
1 Run a blade along the slits on
the back of the front trim and
cut it off the unit.
#####
######
NISSAN
2 TOYOTA
6
max. size
M5 × 8
###
###
Bracket
###
6
max. size
M5 × 8
###
###
6
max. size
M5 × 8
###
###
Bracket
###
6
max. size
M5 × 8
###
###
to dashboard/center console
####
to dashboard/center console
###
Bracket
###
Bracket
###
Existing parts supplied to your car
#####
Existing parts supplied to your car
#####
Slit
###
123
456
78
× 1
#
× 4
#
× 1
#
× 1
#
× 1
#
× 1
#
× 1
#
× 1
#
Parts for Installation and Connection
#####
The numbers in the list are keyed to those in the instructions.
#####
The release key 4 is used for dismounting the unit. See the operating instructions manual for details.
######
#####
#####
#### •
#### •
#### •
#### •
####
####
########
###
###
###
####
###
#####
####
####
######
####
To attach
###
1
182mm
###
53mm
###
SONY XR-3304 (E,Ar) 3-000-000-21 (1)
SONY XR-C210 (E,S,C) 3-800-373-71 (1)
Connections
Caution
• This unit is designed for negative ground 12
V DC operation only.
• Before making connections, disconnect the
ground terminal of the car battery to avoid
short circuits.
• Connect the yellow and red power input
leads only after all other leads have been
connected.
• Be sure to connect the red power input lead to
the positive 12 V power terminal which is
energized when the ignition key is in the
accessory position.
• Run all earth wires to a common earth
point.
####
Notes on the control leads
• The power antenna control lead (blue/white striped) supplies +12 V DC when you turn on the unit.
• A power antenna without relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is
turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities. Otherwise, the speakers may be
damaged.
• Do not connect the terminals of the speaker system to the car chassis, and do not connect the terminals of the right speaker with
those of the left speaker.
• Do not attempt to connect the speakers in parallel.
• Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing so may damage the active
speakers. Therefore, be sure to connect passive speakers to these terminals.
LINE OUT BUS CONTROL IN
from car antenna
#####
Fuse (10A)
###
to a power antenna relay control box
####
AMP/ANT REM
Max. supply current 0.3 A
######
Gray/Black striped
###
Green/Black striped
###
Violet/Black striped
###
5
#####
RCA pin cord (RC-63 (1 m), RC-64 (2 m) or RC-65 (5 m)) (not supplied)
####
Power amplifier
#####
Rear speakers
#####
Blue/white striped
#####
to the +12 V power terminal which is energized in the
accessory position of the ignition key switch
Be sure to connect the black earth lead to it first.
#####
###
to the +12 V power terminal which is energized at all times
Be sure to connect the black earth lead first.
####
####
to a metal point of the car
First connect the black earth lead, then connect the yellow
and red power input leads.
###
####
Black
###
Yellow
###
Red
###
White
###
White/Black striped
###
Gray
###
Green
###
Violet
###
Rear speakers
###
Right
###
Front speakers
####
Left
##
Left
##
Right
###
#####
### •
### •
###
###
###
###
### •
###•
###•
###•
###•
Reset Button
When the installation and connections are over,
be sure to press the reset button with a ball-
point pen etc.
Reset button
####
Note for Connecting
If there is alternator noise (a whining sound when raising engine speed), earth the master unit by
connecting it to a metal point of the car with the supplied chassis earth cord 8. Connect the
ground cord to the master unit with part 2 as shown in the illustration. (In case you do not use
part 2, take screw 7 instead.)
###
###
###
###
To a metal point of the car
###
2
8
Connection Example
#####
######### •
######### •
######### •
######### •
######## •
####
###
####
-
1
-
2
Sony XR-3304 Installation guide
- Category
- Motorcycle Accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sony XR-3300 Installation guide
-
-
Sony MEX-GS600BT Owner's manual
-
-
-
Sony MEX-GS610BT Installation guide
-
Sony CDX-GT575UP Installation guide
-
-
Sony CDX-GT260MP Owner's manual
-