System Sensor 546-9000 User manual

Type
User manual
D770-33-00 1 I56-0052-000
546-9000 Cover Tamper Switch
INSTALLATION AND MAINTENANCE INSTRUCTIONS
A Division of Pittway
3825 Ohio Avenue, St. Charles, Illinois 60174
1-800-SENSOR2, FAX: 630-377-6495
www.systemsensor.com
NOTICE: This manual should be left with the owner/user
of this equipment.
General Information
The System Sensor 546-9000 cover tamper switch mounts
to AFD and LFD Series waterflow devices to monitor re-
moval of the cover. Cover removal produces a switch out-
put. The unit will reset when the product cover is
reinstalled.
Wiring Instructions
1. Remove the waterflow detector cover using the security
wrench provided.
2. Attach the cover tamper switch to upper PCB by snap-
ping. The cover tamper switch assembly snaps into the
bracket mounting holes on the upper PCB in the orienta-
tion shown in Figure 1.
Specifications
Contact Ratings: 5A @ 125/250 VAC
3A @ 30 VDC
Operating Temperature Range: 32° to 120°F (0° to 49°C)
Shipping Weight: 0.115 lbs.
Figure 1.
For use with System Sensor Models:
AFD and LFD Series waterflow detectors
NOTE: To avoid possible damage, support upper PCB
when installing cover tamper switch bracket as-
sembly.
3. Secure the three wires from cover tamper switch to lower
PCB using supplied tie wrap. See Figure 1.
4. Route wires away from mechanisms.
5. Wire the circuit as shown in Figures 2, 3, or 4, or as re-
quired by the installation requirements and as approved
by the authority having jurisdiction. Clip the unused
wire from the tamper switch and use the wire nut to pro-
tect from shorting.
6. Perform the required system tests and include the cover
tamper switch in the test by alternately replacing and re-
moving the cover to produce the desired circuit effects.
7. After testing, secure the cover with the security wrench.
A78-2630-00
COVER TAMPER SWITCH
BLACK/BLUE: OPEN
COVER OFF
BLACK/RED: CLOSED
COVER TAMPER SWITCH
BRACKET ASSEMBLY
P/N 546-9000
UPPER PCB
BRACKET MOUNTING HOLES
BLACK (COM)
BLUE (NORMALLY OPEN)
RED (NORMALLY CLOSED)
LOWER PCB
TIE WRAP
D770-33-00 2 I56-0052-000
©
2000 System Sensor
Three-Year Limited Warranty
System Sensor warrants its enclosed cover tamper switch to be free from
defects in materials and workmanship under normal use and service for a
period of three years from date of manufacture. System Sensor makes no
other express warranty for this cover tamper switch. No agent, representa-
tive, dealer, or employee of the Company has the authority to increase or
alter the obligations or limitations of this Warranty. The Company’s obli-
gation of this Warranty shall be limited to the repair or replacement of any
part of the cover tamper switch which is found to be defective in materials
or workmanship under normal use and service during the three year pe-
riod commencing with the date of manufacture. After phoning System
Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authori-
zation number, send defective units postage prepaid to: System Sensor,
Repair Department, RA #__________, 3825 Ohio Avenue, St. Charles, IL
60174. Please include a note describing the malfunction and suspected
cause of failure. The Company shall not be obligated to repair or replace
units which are found to be defective because of damage, unreasonable
use, modifications, or alterations occurring after the date of manufacture.
In no case shall the Company be liable for any consequential or incidental
damages for breach of this or any other Warranty, expressed or implied
whatsoever, even if the loss or damage is caused by the Company’s negli-
gence or fault. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages, so the above limitation or exclusion may
not apply to you. This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
CONTROL
PANEL
END OF LINE
DEVICE
INITIATING
DEVICES
COVER
TAMPER
SWITCHES
1
2
Figure 2. Class B initiating circuit with single device:
CONTROL
PANEL
END OF LINE
DEVICE
INITIATING
DEVICES
COVER
TAMPER
SWITCHES
SUPERVISORY ZONE
A78-2619-00
Figure 3. Class B initiating circuit with multiple devices:
A78-2618-00
CONTROL
PANEL
END OF LINE
DEVICE
INITIATING
DEVICE
COVER
TAMPER
SWITCH
1
2
A78-2617-00
Figure 4. Class A 4-wire initiating circuit with multiple devices:
  • Page 1 1
  • Page 2 2

System Sensor 546-9000 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI