Streamline MF2300-83 Installation guide

Brand
Streamline
Model
MF2300-83
Category
Wall & ceiling mounts accessories
Type
Installation guide

Streamline MF2300-83 is a faucet designed for installation in bathtubs and shower and has a spout, diverter, and hand shower holder. It comes with a lifetime warranty for both faucet and finish, and replacement parts can be obtained by calling 323-612-8011 or writing to Pacific Coast Import Distributors, Inc. at 425 S. Fairfax ave. #204, Los Angeles, CA 90036. Proof of purchase is required for all warranty claims. The faucet should be cleaned periodically with a soft damp cloth, avoiding abrasive cleaners, steel wool, and harsh chemicals.

Streamline MF2300-83 is a faucet designed for installation in bathtubs and shower and has a spout, diverter, and hand shower holder. It comes with a lifetime warranty for both faucet and finish, and replacement parts can be obtained by calling 323-612-8011 or writing to Pacific Coast Import Distributors, Inc. at 425 S. Fairfax ave. #204, Los Angeles, CA 90036. Proof of purchase is required for all warranty claims. The faucet should be cleaned periodically with a soft damp cloth, avoiding abrasive cleaners, steel wool, and harsh chemicals.

Installation
Everyday cleaning
Please Note : Since manufacturing
of acrylic surface baths takes a great
deal of manual labor especially in
finishing, small irregularities in the
surface are inevitable and inherent to
the chosen product/material.
Shrinkage lines, air holes and casting
marks and blemishes on the
underside of the bath (where they
cannot be seen when the bath is
turned upright) do not adversely
affect performance and should not be
regarded as defects.
It is advised to clean an acrylic
surface bath regularly, to remove any
insoluble products. Warm soapy
water should be used and then the
bath should be wiped. Do not let
cleaners soak in.
Before fitting:remove packaging and
inspect the bath.We strongly
recommend to use a professional
and qualified plumber and installer.
Instructions must be adhered to as
we cannot accept responsibility for
incorrect installation or damage
during the process.
The surface bath has good
resistance properties to acids, but
should not come into contact with
alkalis or organic solvents, such as
caustic soda, some multi-surface
cleaners, bathroom cleaners,
bleaches, harsh solvents, burning
cigarettes, strong chemicals such as
dry-cleaning fluids, paint strippers,
acetone, citrus based chemicals, and
nail/varnish removers.
acrylic
It is advised to always run some cold
water before turning on the hot tap.
With hot water temperatures not
exceeding 65 Celsius.
M-2301-59FSWH-DM M-2301-59FSWH-DM
M-2300-67FSWH-DM M-2300-67FSWH-DM
Used drain meets the requirement of ASME
A112.18.2/CSA B125.2 *Always follow the
appropriate plumbing code
170X80X69
For Model: F-83-H5DM
Bath& Shower Tub Faucet
Your new faucet is designed for years of trouble-free performance. Keep
it looking new by cleaning it periodically with a soft damp cloth. Avoid
abrasive cleaners, steel wool and harsh chemicals. These will dull the
finish and void your warranty.
If you use soldering for the installation of the faucet, all cartridges and
washers will have to be removed before using flame. Otherwise, the
warranty will be void on these parts.
Wear eye protection when cutting water supply lines.
Prior to beginning installation, turn off the cold and hot water lines.
Turn on faucet to release build-up pressure.
1.
STEP 3
STEP 4
STEP 5
Hand shower holder installation
1.Put the base into the hole.
2.Put the hand shower holder through the base.
Valve and water supply connection
STEP 2
Spout installation
1.Disassemble the spout .
2.Place rubber washer
,metal washer and
rubber washer
nut
metal washer
secure the nut.
1.Connect the
flexible hose(not included) to water
supply valve (not included),and
tighten it with adjustable wrench.
STEP 6
HOT
COLD
1.Repeat steps to install the handle
and diverter in the hole located on the
Diverter installation
right of the cold water handle.
STEP 1
Handle installation
1.Disassemble the hot water handle.
2.From underneath, insert the hot water valve,
From Top, install the handle and fixing nut.
3.Screw the nut to secure the valve.
4.Repeat steps to install cold water handle and
rubber washer, metal washer and lock nut.
Handle
fixing nut
rubber washer
metal washer
valve body
cold water valve.
19.69”
19.69”
27.56”
Streamline
2
5
3
4
6
7
8
13
10
11
9
12
27
28
1
14
15
16
17
21
18
19
22
23
20
24
2
5
2
6
323-612-8011
No. Name QTY No. Name QTY
1 Body 1 15 Gasket 1
2 Cartridge 2 16 Changeover Body 1
3 Washer 4 17 Cartridge 1
4 Installation Gasket 4 18 Screw 1
5 O-ring 1 19 Extension Rod 1
6 Nut 1 20 Sleeve 1
7 Screw 3 21 Pull-Out Hose 1
8 Three Pole 2 22 Handle Base 1
9 O-ring 1 23 T-Cov er 1
10 Water feet 1 24 Nut 1
11 Installation Gasket 1 25 Gasket 1
12 Nut 1 26 Hand Shower 1
13 Flexible Hose 2 27 Handle 3
14 Flexible Hose 1 28 O-ring 3
LIFETIME FAUCET AND FINISH LIMITED WARRANTY
All parts and finishes of Streamline faucets are warranted to the original
consumer purchaser to be free from defects in material and workmanship
for as long as the original consumer purchaser owns their home. Streamline
recommends using a professional plumber for all installation and repair.
Streamline will replace, free of charge, during the warranty period any part
of finish that proves defective in material and/or workmanship under normal
installation, use and service. Replacement parts may be obtained by calling
323-612-8011 (in the U.S.) or by writing to:
Pacific Coast Import Distributors, Inc.
425 S.Fairfax ave.
#204
Los Angeles, CA 90036
This warranty is extensive in that it covers replacement of all defective
parts and even finish, but these are the only two things that are covered.
Labor charges/ damage incurred during installation, repair or replacement
as well as any other kind of loss or damages are excluded. Proof of
purchase (original sales receipt) from the original consumer purchaser
must be made available to Streamline for all warranty claims. This is the
exclusive warranty by Streamline, which does not make any other
warranty of any kind, including the implied warranty of merchantability.
This warranty excludes all industrial, commercial and business usage,
whose purchasers are hereby extended a one year limited warranty from
the date of purchase, with all other terms of this warranty applying except
the duration of the warranty. This warranty is applicable to Streamline
faucets manufactured after January 1st, 2018.
Any damage to this faucet as a result of misuse, abuse, or neglect, or any
use of other than genuine Streamline replacement parts will void the
warranty.
This warranty applies only to Streamline faucets installed in the United
States of America and Canada.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Streamline MF2300-83 Installation guide

Brand
Streamline
Model
MF2300-83
Category
Wall & ceiling mounts accessories
Type
Installation guide

Streamline MF2300-83 is a faucet designed for installation in bathtubs and shower and has a spout, diverter, and hand shower holder. It comes with a lifetime warranty for both faucet and finish, and replacement parts can be obtained by calling 323-612-8011 or writing to Pacific Coast Import Distributors, Inc. at 425 S. Fairfax ave. #204, Los Angeles, CA 90036. Proof of purchase is required for all warranty claims. The faucet should be cleaned periodically with a soft damp cloth, avoiding abrasive cleaners, steel wool, and harsh chemicals.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents