Page is loading ...
4214 WENPRODUCTS.COM
2
Table
of
Contents
Technical data………………………………………………………………………………. 2
General safety rules………………………………………………………………………... 3
Specific safety rules for the drill press…………………………………………………… 5
Electrical information………………………………………………………………………. 6
Know your drill press………………………………………………………………………. 8
Assembly and adjustments……………………………………………………………….. 9
Operation……………………………………………………………………………………. 19
Maintenance………………………………………………………………………………… 24
Troubleshooting…………………………………………………………………………….. 25
Replacement parts……………………………………………………………………… 27
Part List…………………………………………………………………………………………... 28
Exploded view……………………………………………………………………………… 30
One year limited warranty…………………………………………………………………….. 31
Technical
data
12" Variable Speed Drill Press with Laser Crosshair Model # 4214
Motor: 120 V, 60 Hz, 4.8 A
Horsepower: 2/3 HP (single phase) Speed:
530–3100 RPM (no load)
Chuck capacity: 1/32–5/8" (0.8–16 mm) Quill
diameter: 2 3/16" (55 mm)
Stroke: 3 1/8" (80 mm)
Capacity: 6" (152 mm) (chuck to column)
19 1/2" (495 mm) (chuck to base)
Table tilt: 0 to 45° left and right
Laser: Class III, transformer powered
Weight: 85 lb
4214 WENPRODUCTS.COM
3
General
safety
r
ules
Safety is a combination of common sense, staying alert, and knowing how your drill press works.
SAVE THESE SAFETY INSTRUCTIONS.
WARNING: To avoid mistakes that could cause serious injury, do not plug in the drill press
until the following steps have been read and understood.
1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations,
and possible hazards.
2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to
rain. Keep work areas well-lit.
3. DO NOT use power tools in the presence of flammable liquids or gases.
4. ALWAYS keep your work area clean, uncluttered, and well-lit. DO NOT work on floor surfaces that are
slippery.
5. KEEP BYSTANDERS AT A SAFE DISTANCE from the work area, especially when the tool is
operating. NEVER allow children or pets near the tool.
6. DO NOT FORCE THE TOOL to do a job that it was not designed to do.
7. DRESS FOR SAFETY. Do not wear loose clothing, gloves, neckties, or jewelry (rings, watches, etc.)
when operating the tool. Inappropriate clothing and items can get caught in moving parts and draw
you in. ALWAYS wear non-slip footwear and tie back long hair.
8. WEAR A FACE MASK OR DUST MASK as the drilling operation produces dust.
WARNING: Dust generated from certain materials can be hazardous to your health. Always operate
this tool in a well-ventilated area and provide for proper dust removal. Use dust collection systems
whenever possible.
9. ALWAYS remove the power cord plug from the electrical outlet when making adjustments, changing parts,
cleaning, or working on the tool.
10. KEEP GUARDS IN PLACE AND IN WORKING ORDER.
11. AVOID ACCIDENTAL START-UPS. Make sure the power switch is in the OFF position before
plugging in the power cord.
12. REMOVE ADJUSTMENT TOOLS. Always make sure all adjustment tools are removed from the drill
press before turning it on.
4214 WENPRODUCTS.COM
4
General
safety
r
ules
(continued)
13. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. Do not
leave the tool until it has come to a complete stop.
14. NEVER STAND ON A TOOL. Serious injury could result if the tool tips or is accidentally hit. DO
NOT store anything above or near the tool.
15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-
soled footwear. Keep the floor clear of oil, scrap, and other debris.
16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow
instructions for lubricating and changing accessories.
17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper
mounting, or any other conditions that may affect the tool’s operation. Any part that
is damaged should be properly repaired or replaced before use.
18. MAKE THE WORKSHOP CHILDPROOF. Use padlocks and master switches and ALWAYS remove
starter keys.
19. DO NOT operate the tool if you are under the influence of drugs, alcohol, or medication that could
affect your ability to use the tool properly.
20. USE SAFETY GOGGLES AT ALL TIMES—that comply with ANSI Z87.1.
Normal safety glasses only have impact resistant lenses and are not designed for
safety. Wear a face or dust mask when working in a dusty environment. Use ear
protection, such as plugs or muffs, during extended periods of operation.
Laser safety
1. Do not stare directly at the laser beam. Eye damage may occur if
you deliberately stare into the beam.
2. The laser light beam used in this system is Class III.
AVOID DIRECT EYE EXPOSURE.
3. The laser must be used and maintained in accordance with
the manufacturer’s instructions:
• Never aim the beam at any person or an object other than the
workpiece.
• Do not project the laser beam into the eyes of others.
• Always ensure the laser beam is aimed at a workpiece
without reflective surfaces as the laser beam could be
projected into your eyes or the eyes of others.
4214 WENPRODUCTS.COM
5
Specific
safety
r
ules
for
the
drill
press
WARNING: Do not operate the drill press until it is completely assembled and installed according to
the instructions.
1. Never turn the drill press on until the table is clear of all foreign objects (tools, scraps, etc.).
2. Always keep hands and fingers away from the drill bit.
3. Do not drill materials that do not have a flat surface—unless a suitable support is used (clamp
or vise).
4. Never start the drill press with the drill bit pressed against the workpiece.
5. Make sure the table lock is tightened before starting the drill press.
6. Never layout, assemble, or set-up any work on the table while the drill is on.
7. Make sure drill bit is securely locked in the chuck.
8. Make sure chuck key is removed from the chuck before turning power on.
9. Adjust the table or depth stop to avoid drilling into the table.
10. Always stop the drill before removing scrap pieces from the table.
11. Use clamps or a vise to secure a workpiece to the table. This will prevent the workpiece from rotating
with the drill bit.
12. Do not wear gloves when operating a drill press.
13. Set the drill press to the speed that is appropriate for the material being drilled.
14. Should any part of the drill press be missing, damaged, or any electrical component fail to perform
properly, shut the power OFF and unplug the drill press. Replace missing, damaged, or failed parts
before resuming operation.
15. Before leaving the machine, shut the power off, remove the drill bit, and clean the table.
4214 WENPRODUCTS.COM
6
1 - 3-prong plug
2 - Properly grounded outlet
3 - Grounding prong
Electrical
information
Grounding instructions
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance
for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an
equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that
is properly installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the outlet, have the proper outlet installed by a
licensed electrician.
IMPROPER CONNECTION of the equipment grounding conductor can result in electric shock. The conductor
with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or
replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a
live terminal.
CHECK with a licensed electrician or service personnel if you do not completely understand the
grounding instructions, or if you are not sure if the tool is properly grounded.
USE ONLY THREE-WIRE EXTENSION CORDS that have
3-pronged plugs and outlets that accept the tool's plug as
shown in Fig. A. Repair or replace a damaged or worn cord
immediately.
Fig. A
1
3
2
1. 3-pronged plug 2. Properly grounded outlet
3. Grounding prong
CAUTION: In all cases, make certain the outlet in question is properly grounded. If you are not sure if it is,
have a licensed electrician check the outlet.
4214 WENPRODUCTS.COM
7
Electrical
information
(continued)
WARNING: This drill press is for indoor use only. Do not expose to rain or use in damp locations.
Guidelines for using extension cords
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The table below shows the correct size to be used according to cord
length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
Ampere rating Total length of cord in feet (meters)
More than Not more than 25 (7.6) 50 (15) 100 (30.4) 150 (45.7)
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not recommended
Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension
cord or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit must not be less than a #12 wire and should be
protected with a 15 A time-delayed fuse. Before connecting the motor to the power line, make sure the switch
is in the OFF position and the electric current is rated the same as the current stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
WARNING: This tool must be grounded while in use to protect the operator from electric shock.
4214 WENPRODUCTS.COM
8
Know
your
drill
press
Fig. 1
A Digital speed readout
B ON/OFF switch
C Depth scale
D Chuck
E Table
F Feed handles
G Housing cover screw
H Housing cover
I Column
J Rack
K Crank handle
L Column support
M Base
N Table lock handle
O Bevel lock bolt
P Bevel scale
Q Laser line ON/OFF switch
R LED worklight switch
S Extension wing with
integrated rollers
T Support lock handle
U Speed control handle
V Power cord
4214 WENPRODUCTS.COM
9
Assembly
and
adjustments
Unpacking (Fig. 2)
Unpack the drill press and all its parts, and compare against the list below. Do not discard the carton or
any packaging until the drill press is completely assembled.
To protect the drill press from moisture, a protective coating has been applied to the machined surfaces.
Remove this coating with a soft cloth moistened with kerosene or WD-40
®
. Do not use acetone, gasoline, or
lacquer thinner to clean. Apply a coat of good paste wax to the table and column. Wipe all parts with a clean
dry cloth.
Fig. 2
A
B
C
D
N
E
H
F
M
K
I
L
R
J
G
S
Q O P
A Head/motor assembly
B Column assembly and table bracket
C Table
D Base
E Chuck arbor
F Chuck
G Extension wing with integrated rollers
H Chuck key
I Wing knobs (2)
J Table lock handles (2)
K Hex head bolts (4)
L Table crank handle
M Hex keys (2)
N Feed and speed handles (4)
O Clamp assembly
P LED bulb
Q Table adjustment wrench
R Wedge
S Laser enhancing glasses
4214 WENPRODUCTS.COM
10
Assembly
and
adjustments
(continued)
WARNING: If any part is missing or damaged, do not plug the drill press in until the missing or
damaged part is repaired or replaced, and assembly is complete.
The column assembly (column, column support, rack,
rack collar, and table support bracket) must be
attached to the base. The table and table support
handles must be attached to the table support bracket.
The motor housing must be attached to the column.
Tools needed for assembly
• Adjustable wrench
• screwdriver
• Hammer and block of wood
Column assembly to base (Fig. 3)
1. Place the column tube (1) on the base (2),
aligning the column support holes to the base
holes.
2. Install a hex head bolt (3) in each column
support hole and tighten bolts using the
adjustable wrench.
Table to table support bracket (Fig. 4)
1. Loose rack collar hex screw M8X10.
2. Remove rack collar and rack from column.
3. Place rack (teeth up) in slot of table support.
4. Slide table support with rack in slot onto
column.
5. Slide rack collar down column onto beveled end
of rack and tighten rack collar hex screw
6. Place the crank handle (1) onto the shaft (2) of
the table bracket so the flat of the shaft is under
the set screw (3). Tighten the set screw.
7. Thread the table lock handle (4) into the
front of the table support bracket.
8. Thread the table support lock handle into
the rear of the table support bracket (not
shown).
9. Position the table (5) in the same direction as
the base, install the table, and tighten the table
lock handle (4).
Fig. 3
1
3
2
Fig. 4
5
2
4
1
3
4214 WENPRODUCTS.COM
11
Assembly
and
adjustments
(continued)
Drill press head to column (Fig. 5)
CAUTION: The drill press head is heavy. To avoid
injury, two people should lift it into position.
1. Carefully lift the drill press head assembly (1) and
position it over the column (2).
2. Place the mounting opening (3) on the drill press
head over the top of the column. Make sure the drill
press head is seated properly on the column.
3. Align the direction of the drill press head with the
direction of the base and the table.
4. Tighten the set screw (4) using a hex key.
Feed handles (Fig. 6)
1. Insert the three feed handles (1) into the
threaded openings on the feed hub (2).
2. Manually tighten handles into openings.
Note: When using the drill press, one or two of the
feed handles may be removed if an unusually-
shaped workpiece interferes with handle
rotation.
Speed handle (Fig. 7)
1. Insert the feed handle (1) into the threaded
opening on the speed hub (2).
2. Manually tighten handle into opening.
Fig. 5
1
4
2 3
Fig. 6
1
2
Fig. 7
2
1
4214 WENPRODUCTS.COM
12
Assembly
and
adjustments
(continued)
Mount the drill press (Fig. 8)
The drill press must be securely fastened through the
mounting holes (1) to a stand or workbench with heavy-
duty fasteners. This will prevent the drill press from
tipping over, sliding, or walking during operation.
IMPORTANT: If the stand or workbench has a
tendency to move during operation, fasten the
workbench securely to the floor.
LED bulb (Fig. 9)
Insert the LED bulb (1) into the socket (2) in the
motor head assembly.
Fig. 8
1
Fig. 9
2
1
4214 WENPRODUCTS.COM
13
2
Assembly
and
adjustments
(continued)
Chuck adjustments
Install the chuck (Fig. 10)
1. Inspect and clean the taper hole in the chuck
(1) and the spindle (2). Remove all grease,
coatings, and particles from the chuck and
spindle surfaces with a clean cloth.
2. Open the chuck jaws (3) by manually turning the
chuck barrel clockwise. Make sure the jaws are
completely recessed inside the chuck.
3. Insert the chuck arbor (4) into the opening at the
top of the chuck (1).
4. Seat the chuck and chuck arbor on the spindle by
placing a block of wood (5; not included) under the
chuck (1) and tapping the wood with a hammer (6;
not included) or tap the chuck with a rubber mallet
(not included).
CAUTION: To avoid damaging the chuck, make
sure the jaws are completely recessed into the chuck.
Do not use a metal hammer to drive the chuck into
the spindle.
Fig. 10
4
2
4
1
1
3
5
6
Fig. 11
Remove the chuck (Fig. 11)
1.
Turn the feed handles (1) to lower the chuck (2)
3
to the lowest position.
4
2. Slide the wedge (3) into the opening in the quill. Tap
on the wedge using a hammer (4; not
included). The chuck and arbor will drop out.
1
Note: To avoid possible damage to the drill or
chuck, be prepared to catch the chuck as it
falls.
4214 WENPRODUCTS.COM
14
Assembly
and
adjustments
(continued)
Table adjustments
Raise or lower the table (Fig. 12)
1. Loosen the support lock handle (1) and turn the
crank handle (2) until the table is at the desired
height.
2. Tighten the support lock handle before drilling.
Rotate the table (Fig. 12)
1. Loosen the support lock handle (1) and turn the table
around the column to the desired position.
Note: The rack should rotate around the column with
the table support bracket. If the rack binds
and will not rotate, slightly loosen
the set screw in the rack collar.
2. Tighten the support lock before drilling.
Tilt the table (Fig. 13)
1. Loosen the bevel lock bolt (1) with the table
adjustment wrench provided, or with a suitable
socket wrench.
2. Tilt the table to the desired angle, using the bevel
scale (2) as a basic guide.
3. Re-tighten the bevel lock bolt.
4. To return the table to its original horizontal
position, loosen the bevel lock bolt (1).
5. Realign the table to the 0° setting on the bevel scale
(2).
6. Tighten the bevel lock bolt with the wrench.
Install the table extension (Fig. 14)
1. Insert the two rods (1) of the table extension into the
two channels (2) at the side of the table.
2. Place a wing knob (3) in the opening on the bottom
of each channel and tighten to secure the extension
to the table.
Fig. 12
1
2
Fig. 13
2
1
Fig. 14
1
2
3
4214 WENPRODUCTS.COM
15
Assembly
and
adjustments
(continued)
WARNING: To avoid injury, make sure the chuck key is removed from the chuck before starting any
drilling operation.
Install drill bits (Fig. 15)
1. Place the chuck key (1) into the side keyhole of the
chuck (2), meshing the key with the gear teeth.
2. Turn the chuck key counterclockwise to open the
chuck jaws (3).
3. Insert a drill bit (4) into the chuck far enough to
obtain maximum gripping of the chuck jaws.
4. Center the drill bit in the chuck jaws before final
tightening of the chuck.
5. Tighten the chuck jaws using the chuck key to ensure
that the drill bit will not slip while drilling.
6. Remove the chuck key.
Square the table to the drill bit (Fig. 16)
1. Insert a 3" (7.6 cm) long drill bit (1) into the
chuck (2) and tighten the jaws with the chuck
key.
2. Raise the table with the crank handle (3), and lock
the table (4) approximately 1" (2.5 cm) below the
drill bit.
3. Place a combination square (5; not included) on the
table as shown, placing the long straight edge of the
combination square against the drill bit. Make sure the
drill bit is parallel or aligned exactly to the straight
edge of the square.
4. If an adjustment is needed, loosen the bevel lock
bolt (6) with a wrench.
1
4
Fig. 16
Fig. 15
2
3
6
5. Tilt the table slightly, until the combination straight edge is aligned perfectly with the drill bit.
6. Tighten the bevel lock when square.
Note: Adjustments for the correct function of your drill press return spring have been done at the
factory. Please do not modify them. However, prolonged use of the drill press may make some
readjustments necessary.
4214 WENPRODUCTS.COM
16
Assembly
and
adjustments
(continued)
Laser line (Fig. 17 and 18)
WARNING: Do not stare directly at the laser beam! A hazard may exist if you deliberately
stare into the beam. Please observe all safety rules.
• Never aim the beam at any person or an object other than the workpiece.
• Do not project the laser beam into the eyes of others.
• Always make sure the laser beam is aimed at a workpiece that dos not possess reflective surfaces as
the laser beam could be projected into your eyes or the eyes of others.
1. Place a workpiece on the table.
2. Turn the laser switch (1) to the ON position.
3. Lower the drill bit to meet the workpiece (2). The two laser
lines should cross where the drill meets the workpiece.
4. If the laser needs to be adjusted:
a. Using a 3 mm hex key, turn the laser adjustment
set screws (3) counterclockwise.
b. Rotate the laser light housing (4) until the two
laser lines intersect where the drill meets the
workpiece. DO NOT stare directly at the laser
lines.
5. Re-tighten the adjustment set screws (3).
Fig. 17
1
3
4
Fig. 18
2
4214 WENPRODUCTS.COM
17
Assembly
and
adjustments
(continued)
Spindle return spring (Fig. 19)
The spindle is equipped with an auto-return mechanism. The
main components are a spring and a notched housing. The
spring was properly adjusted at the factory and should not be
readjusted unless absolutely necessary.
1. Unplug the drill press.
2. Place a screwdriver into the loop (1) to hold the
spring in place.
3. Loosen the two housing nuts (2) approximately 1/4" (6
mm). Do not remove the nuts from the threaded shaft.
Do not allow the spring or spring housing to slip out
of control.
4. While firmly holding the spring housing (3), carefully pull
the spring housing out until it clears the raised notch (4).
5. Turn the housing so that the next notch (5) is
engaged with the raised notch (4).
ï‚· To increase the spindle return tension, turn the
spring housing counter-clockwise.
ï‚· To decrease the tension, turn the spring housing
clockwise.
6. Tighten the two housing nuts. Do not overtighten the two
nuts. If the nuts are tightened too much, the movement
of the spindle and feed handles will become sluggish.
Fig. 19
4
1
2
5
3
Fig. 20
2
1
Angular "play" of the spindle (Fig. 20)
Move the spindle to the lowest downward position and hold in place. Try to make the spindle revolve around its
axis while also moving it with a side motion. If there is too much "play", proceed as follows:
1. Loosen the lock nut (1).
2. Without obstructing the upward and downward motion of the spindle, turn the screw (2) clockwise to
eliminate the "play". Note: A little bit of "play" is normal.
3. Tighten the lock nut (1).
4214 WENPRODUCTS.COM
18
Assembly
and
adjustments
(continued)
WARNING: Disconnect the drill press from the power source before replacing the belt.
Replace the belt (Fig. 21)
Belt tension and drill press speed is controlled by
automatic adjustments made to the diameter of the front
spindle when the drive handle is moved.
Note: See page 23 for information on the variable speed
function of this drill press.
Remove the screw that secures the housing cover (1).
Open the housing cover.
Remove the belt (2) from the housing cover if it is
broken. If it is not broken, but is too stretched to
operate correctly, work the belt off the drive (motor)
spindle (3). Then remove the belt from the front
spindle (4).
Replace the belt by putting a new belt over the
Fig. 21
1
3
4
2
front spindle (4) and carefully sliding the belt over the drive (motor) spindle (3).
WARNING: Do not change the drive speed when the drill press is turned off.
Install the clamp assembly (Fig. 22)
1. Place the two metal squares (1) of the clamp
assembly into two corners of the table and align
the tapered edge of the squares with the grooves.
2. Align the long slots on the base of the clamp over the
openings in the metal squares.
3. Place a washer (2) over the threaded end of each lock
handle (3). Insert the lock handles into the metal
squares. Tighten handles loosely.
4. Position the clamp as needed on the table and fully
tighten the lock handles to secure the clamp.
5. Loosen the wing nut (4) to move the small support
on the front of the clamp into position. Tighten the
wing nut to secure.
Fig. 22
3
4
1
2
1
4214 WENPRODUCTS.COM
19
Operation
Drill Press ON/OFF switch (Fig. 23)
1. To turn the drill press ON, insert the yellow safety key
(1) into the switch housing (2). As a safety feature, the
switch cannot be turned ON without the safety key.
2. Flip the switch (3) upward to the ON position.
3. To turn the drill press OFF, press the switch
downward.
4. To lock the switch in the OFF position, remove the
safety key (1) from the switch. Store the safety key in a
safe place.
Light and laser line ON/OFF switches (Fig. 23)
The light switch (4) is located below the ON/OFF
switch on the left.
The laser switch (5) is located below the ON/OFF switch
on the right.
Position the table and workpiece (Fig. 24)
Always place a piece of backup material (1)
(wood, plywood, etc.) on the table underneath the workpiece
(2). This will prevent splintering on the underside of the
workpiece as the drill bit breaks through. To keep the
material from spinning out of control, it must contact the left
side (3) of the column as illustrated, or be clamped (4; not
included) to
the table.
Note: For small workpieces that cannot be clamped to the
table, use a drill press vise (not included). The vise must be
clamped or bolted to the table to avoid injury.
Fig. 23
2
1
3
4
5
3
Fig. 24
4
3
2
1
4214 WENPRODUCTS.COM
20
Operation
(continued)
General drilling guidelines
WARNING: To prevent the workpiece and the backup material from slipping from your hand
while drilling, position the workpiece and backup material to the left side of the column. If the
workpiece and the backup material are not long enough to reach the column, clamp the workpiece and
backup material to the table. Failure to do this could result in personal injury.
Drill a hole
1. Mark where you want to drill in workpiece by using a center punch or a sharp nail or turn ON Laser
Line to mark drilling point.
2. Before turning ON the drill press, turn the feed handles to bring the drill bit down. Line the drill bit tip up
with the mark. Clamp the workpiece in place.
3. Turn ON the drill press and pull down on the feed handles with appropriate force needed to allow the
drill bit to drill material.
Note: Feeding too slowly might cause the drill bit to turn in the chuck. Feeding too rapidly
might stop the motor, cause the belt to slip, force the workpiece loose, or break the drill bit.
Practice with scrap material to get the feel of the machine before attempting to do
any drilling operation.
Adjust the drilling depth (Fig. 25)
The depth gauge controls the maximum distance the drill bit
will move up or down.
To stop the drill bit at a pre-measured depth:
1. Rotate the lower depth scale knob (2) until the bottom
Fig. 25
1
2
of the knob is aligned with the desired depth mark (5)
5
on the gauge scale.
2. Rotate the depth scale lock knob (1) until it meets the 4
lower depth scale knob (2). The chuck will stop after
travelling downward to the selected distance.
3
Adjust the quill (return) height (Fig. 25)
To adjust the upward distance the quill (shaft that moves up and
down) can travel:
1. Turn the feed handles until the quill is at the desired height
and hold it there.
2. Rotate the lower depth knob (3) until it rests against the
bottom of the metal gauge support (4).
/
