Miller BIG BLUE 400 PRO SERIES Owner's manual

Brand: Miller

Model: BIG BLUE 400 PRO SERIES

Category: Welding System

Type: Owner's manual

This manual is also suitable for

Big Blue 400 And 400 X

Pro Series

CAT, Kubota, And Mitsubishi Engines

CE and Non−CE Models

Big Blue 300R Pro

Kubota Engine

OM-264 359G 2015−10

Processes

Description

Air Carbon Arc (CAC-A)

Cutting and Gouging

Stick (SMAW) Welding

Engine Driven Welder/Generator

TIG (GTAW) Welding

MIG (GMAW) Welding

Flux Cored (FCAW) Welding

Visit our website at

www.MillerWelds.com

File: Engine Drive

Miller Electric manufactures a full line

of welders and welding related equipment.

For information on other quality Miller

products, contact your local Miller distributor to receive the latest full

line catalog or individual specification sheets. To locate your nearest

distributor or service agency call 1-800-4-A-Miller, or visit us at

www.MillerWelds.com on the web.

Thank you and congratulations on choosing Miller. Now you can get

the job done and get it done right. We know you don’t have time to do

it any other way.

That’s why when Niels Miller first started building arc welders in 1929,

he made sure his products offered long-lasting value and superior

quality. Like you, his customers couldn’t afford anything less. Miller

products had to be more than the best they could be. They had to be the

best you could buy.

Today, the people that build and sell Miller products continue the

tradition. They’re just as committed to providing equipment and service

that meets the high standards of quality and value established in 1929.

This Owner’s Manual is designed to help you get the most out of your

Miller products. Please take time to read the Safety precautions. They

will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick

and easy. With Miller you can count on years

of reliable service with proper maintenance.

And if for some reason the unit needs repair,

there’s a Troubleshooting section that will

help you figure out what the problem is. The

parts list will then help you to decide the

exact part you may need to fix the problem.

Warranty and service information for your

particular model are also provided.

Miller is the first welding

equipment manufacturer in

the U.S.A. to be registered to

the ISO 9001:2000 Quality

System Standard.

Working as hard as you do

− every power source from

Miller is backed by the most

hassle-free warranty in the

business.

From Miller to You

Mil_Thank 2009−09

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING 1.................................

1-1. Symbol Usage 1.......................................................................

1-2. Arc Welding Hazards 1.................................................................

1-3. Engine Hazards 3......................................................................

1-4. Compressed Air Hazards 3..............................................................

1-5. Additional Symbols For Installation, Operation, And Maintenance 4.............................

1-6. California Proposition 65 Warnings 6......................................................

1-7. Principal Safety Standards 6.............................................................

1-8. EMF Information 6.....................................................................

SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION 7..........................

2-1. Signification des symboles 7.............................................................

2-2. Dangers relatifs au soudage à l’arc 7......................................................

2-3. Dangers existant en relation avec le moteur 9..............................................

2-4. Dangers liés à l’air comprimé 10...........................................................

2-5. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance 11.....

2-6. Proposition californienne 65 Avertissements 13..............................................

2-7. Principales normes de sécurité 13.........................................................

2-8. Informations relatives aux CEM 13.........................................................

SECTION 3 − DEFINITIONS 15..................................................................

3-1. Additional Safety Symbols And Definitions 15................................................

3-2. Miscellaneous Symbols And Definitions 16..................................................

SECTION 4 − SPECIFICATIONS 18..............................................................

4-1. Serial Number And Rating Label Location 18................................................

4-2. Weld, Power, And Engine Specifications 18.................................................

4-3. Dimensions, Weights, And Operating Angles 18..............................................

4-4. Environmental Specifications 18...........................................................

4-5. Static Output Characteristics 19...........................................................

4-6. Duty Cycle And Overheating 19...........................................................

4-7. Fuel Consumption 19....................................................................

SECTION 5 − INSTALLATION 20................................................................

5-1. Installing Welder/Generator 20............................................................

5-3. Installing Exhaust Pipe 21................................................................

5-4. Connecting The Battery 22...............................................................

5-5. CAT Engine Oil Prestart Information 23.....................................................

5-6. Kubota Engine Oil Prestart Information 23...................................................

5-7. Mitsubishi Engine Oil Prestart Information 23................................................

5-8. Engine General Information 24............................................................

5-9. Engine Fuel And Coolant Prestart Information 24.............................................

5-10. Weld Output Terminals 25................................................................

5-11. Connecting To Weld Output Terminals 25...................................................

5-12. Selecting Cable Sizes* 26................................................................

5-13. Connecting To Remote 14 Receptacle RC14 26..............................................

SECTION 6 − OPERATING WELDER/GENERATOR 27.............................................

6-1. Front Panel Controls (See Section 6-2) 27..................................................

6-2. Description Of Front Panel Controls (See Section 6-1) 28......................................

6-3. Process/Contactor Switch 29.............................................................

6-4. Low Open-Circuit Voltage (VRD) Switch Mode 30............................................

TABLE OF CONTENTS

6-5. Stick Start Procedure − Scratch Start Technique 30...........................................

6-6. Lift-Arc TIG With Crater-Out And Auto-Stop 31...........................................

6-7. Remote Voltage/Amperage Control 32......................................................

6-8. Operating Engine Block Heater 33.........................................................

6-9. Fuel/Hour Gauge Descriptions 34..........................................................

SECTION 7 − OPERATING AUXILIARY EQUIPMENT 35............................................

7-1. Generator Power Receptacles 35..........................................................

7-2. Export Auxiliary Power Receptacles 36.....................................................

7-3. GFCI Receptacle Information, Resetting And Testing 37.......................................

SECTION 8 − MAINTENANCE & TROUBLESHOOTING 38.........................................

8-1. CAT Maintenance Label 38...............................................................

8-2. Mitsubishi Maintenance Label 39..........................................................

8-3. Kubota Maintenance Label 40.............................................................

8-4. Routine Maintenance 41.................................................................

8-5. Servicing Air Cleaner 42.................................................................

8-6. Checking Generator Brushes 43...........................................................

8-7. Inspecting And Cleaning Optional Spark Arrestor Muffler 43....................................

8-8. Servicing Engine Cooling System 44.......................................................

8-9. CAT Engine Speed Adjustment 45.........................................................

8-10. Mitsubishi Engine Speed Adjustment 46....................................................

8-11. Kubota Engine Speed Adjustment 46.......................................................

8-12. Overload Protection 47..................................................................

8-13. Servicing Fuel And Lubrication Systems 48.................................................

8-14. Voltmeter/Ammeter Help Displays 50.......................................................

8-15. Maintaining Stainless Steel (Models With Optional Package) 50................................

8-16. Battery Maintenance 50..................................................................

8-17. Troubleshooting 51......................................................................

SECTION 9 − PARTS LIST 53...................................................................

9-1. Recommended Spare Parts 53............................................................

SECTION 10 − ELECTRICAL DIAGRAMS 54......................................................

SECTION 11 − RUN-IN PROCEDURE 60.........................................................

11-1. Wetstacking 60.........................................................................

11-2. Run-In Procedure Using Load Bank Or Resistance Grid 61....................................

SECTION 12 − GENERATOR POWER GUIDELINES 62............................................

COMPLETE PARTS LIST − Available at www.MillerWelds.com

WARRANTY

DECLARATION OF CONFORMITY

for European Community (CE marked) products.

MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914, U.S.A. declares that the

product(s) identified in this declaration conform to the essential requirements and provisions of

the stated Council Directive(s) and Standard(s).

Product/Apparatus Identification:

Product

Stock Number

Big Blue 400X Pro 907630, 907631

Big Blue 400X 907143, 907143001

RedDArc D402K 4+12 500498002

Council Directives:

·2006/95/EC Low Voltage

·2004/108/EC Electromagnetic Compatibility

·2011/65/EU Restriction of the use of certain Hazardous Substances in electrical and electronic equipment

·2000/14/EC & 2005/88/EC Outdoor Noise

·Notified Body: AV Technology; AVTECH House, Arkle Avenue; Stanley Green Trading Estate; Hand

forth, Cheshire, SK93RW, United Kingdom

·Conformity Assessment Procedure Followed: Annex VI, 2000/14/EC

·Technical Document Holder: Manufacturer

·Notified Body Evaluation Report No: GB/1067/0550/04

·Measured Sound Power level: 96 dB L

·Guaranteed Sound Power Level: 96 dB L

·Electric Power P

: 9.6 kW

Standards:

• IEC 609741:2005 Arc welding equipment – Part 1: Welding power sources

• IEC 6097410:2007 Arc Welding Equipment – Part 10: Electromagnetic compatibility (EMC) requirements

Signatory:

_____________________________________ ___________________________________________

David A. Werba Date of Declaration

MANAGER, PRODUCT DESIGN COMPLIANCE

May 29, 2014

245808B

Page is loading ...

OM-264 359 Page 1

SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING

rom_2015−09

Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if

not avoided, will result in death or serious injury. The

possible hazards are shown in the adjoining symbols

or explained in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or ex-

plained in the text.

NOTICE − Indicates statements not related to personal injury.

 Indicates special instructions.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-

bols and related instructions below for necessary actions to avoid the

hazards.

1-2. Arc Welding Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instructions

to avoid the hazard. The safety information given below is

only a summary of the more complete safety information

found in the Safety Standards listed in Section 1-7. Read and

follow all Safety Standards.

Only qualified persons should install, operate, maintain, and

repair this unit.

During operation, keep everybody, especially children, away.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automat-

ic wire welding, the wire, wire reel, drive roll housing,

and all metal parts touching the welding wire are

electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

ELECTRIC SHOCK can kill.

 Do not touch live electrical parts.

 Wear dry, hole-free insulating gloves and body protection.

 Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

 Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

 Use AC output ONLY if required for the welding process.

 If AC output is required, use remote output control if present on

unit.

 Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

 Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

 Properly install, ground, and operate this equipment according to

its Owner’s Manual and national, state, and local codes.

 Always verify the supply ground — check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

 When making input connections, attach proper grounding conduc-

tor first − double-check connections.

 Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

 Frequently inspect input power cord and ground conductor for

damage or bare wiring – replace immediately if damaged – bare

wiring can kill.

 Turn off all equipment when not in use.

 Do not use worn, damaged, undersized, or repaired cables.

 Do not drape cables over your body.

 If earth grounding of the workpiece is required, ground it directly

with a separate cable.

 Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

 Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

 Do not touch electrode holders connected to two welding ma-

chines at the same time since double open-circuit voltage will be

present.

 Wear a safety harness if working above floor level.

 Keep all panels and covers securely in place.

 Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

 Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

 Do not connect more than one electrode or work cable to any

single weld output terminal. Disconnect cable for process not in

use.

 Use GFCI protection when operating auxiliary equipment. Do not

test or reset GFCI receptacles at idle speed/low voltage or the

GFCI will be damaged and not provide protection from electric

shock caused by a ground fault.

SIGNIFICANT DC VOLTAGE exists in inverter power

sources AFTER stopping engine.

 Stop engine on inverter and discharge input capacitors according

to instructions in Maintenance Section before touching any parts.

HOT PARTS can burn.

 Do not touch hot parts bare handed.

 Allow cooling period before working on

equipment.

 To handle hot parts, use proper tools and/or wear heavy, insu-

lated welding gloves and clothing to prevent burns.

OM-264 359 Page 2

FLYING METAL or DIRT can injure

eyes.

 Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

 Wear approved safety glasses with side shields even under your

welding helmet.

FUMES AND GASES can be

hazardous.

Welding produces fumes and gases. Breathing thes

fumes and gases can be hazardous to your health.

 Keep your head out of the fumes. Do not breathe the fumes.

 If inside, ventilate the area and/or use local forced ventilation at the

arc to remove welding fumes and gases. The recommended way

to determine adequate ventilation is to sample for the composition

and quantity of fumes and gases to which personnel are exposed.

 If ventilation is poor, wear an approved air-supplied respirator.

 Read and understand the Safety Data Sheets (SDSs) and the

manufacturer’s instructions for adhesives, coatings, cleaners,

consumables, coolants, degreasers, fluxes, and metals.

 Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

 Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

 Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and while wearing an air-supplied

respirator. The coatings and any metals containing these elements

can give off toxic fumes if welded.

BUILDUP OF GAS can injure or kill.

 Shut off compressed gas supply when not in use.

 Always ventilate confined spaces or use ap-

proved air-supplied respirator.

ARC RAYS can burn eyes and skin.

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from the

weld.

 Wear an approved welding helmet fitted with a proper shade of filter

lenses to protect your face and eyes from arc rays and sparks

when welding or watching (see ANSI Z49.1 and Z87.1 listed in

Safety Standards).

 Wear approved safety glasses with side shields under your

helmet.

 Use protective screens or barriers to protect others from flash,

glare, and sparks; warn others not to watch the arc.

 Wear body protection made from durable, flame-resistant material

(leather, heavy cotton, wool). Body protection includes oil-free

clothing such as leather gloves, heavy shirt, cuffless trousers, high

shoes, and a cap.

WELDING can cause fire or explosion

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

 Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

 Do not weld where flying sparks can strike flammable material.

 Protect yourself and others from flying sparks and hot metal.

 Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

 Watch for fire, and keep a fire extinguisher nearby.

 Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

 Do not weld on containers that have held combustibles, or on

closed containers such as tanks, drums, or pipes unless they are

properly prepared according to AWS F4.1 and AWS A6.0 (see

Safety Standards).

 Do not weld where the atmosphere can contain flammable dust,

gas, or liquid vapors (such as gasoline).

 Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock, sparks, and fire haz-

ards.

 Do not use welder to thaw frozen pipes.

 Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

 Wear body protection made from durable, flame-resistant material

(leather, heavy cotton, wool). Body protection includes oil-free

clothing such as leather gloves, heavy shirt, cuffless trousers, high

shoes, and a cap.

 Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

 After completion of work, inspect area to ensure it is free of sparks,

glowing embers, and flames.

 Use only correct fuses or circuit breakers. Do not oversize or by-

pass them.

 Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

 Read and understand the Safety Data Sheets (SDSs) and the

manufacturer’s instructions for adhesives, coatings, cleaners,

consumables, coolants, degreasers, fluxes, and metals.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

 Wear approved ear protection if noise level is

high.

ELECTRIC AND MAGNETIC FIELDS (EMF)

can affect Implanted Medical Devices.

 Wearers of Pacemakers and other Implanted

Medical Devices should keep away.

 Implanted Medical Device wearers should con-

sult their doctor and the device manufacturer before going near arc

welding, spot welding, gouging, plasma arc cutting, or induction

heating operations.

CYLINDERS can explode if damaged.

Compressed gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

 Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, physical damage, slag, open flames, sparks, and arcs.

 Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

 Keep cylinders away from any welding or other electrical circuits.

 Never drape a welding torch over a gas cylinder.

 Never allow a welding electrode to touch any cylinder.

 Never weld on a pressurized cylinder — explosion will result.

 Use only correct compressed gas cylinders, regulators, hoses,

and fittings designed for the specific application; maintain them

and associated parts in good condition.

 Turn face away from valve outlet when opening cylinder valve. Do

not stand in front of or behind the regulator when opening the valve.

 Keep protective cap in place over valve except when cylinder is in

use or connected for use.

 Use the right equipment, correct procedures, and sufficient num-

ber of persons to lift and move cylinders.

 Read and follow instructions on compressed gas cylinders,

associated equipment, and Compressed Gas Association (CGA)

publication P-1 listed in Safety Standards.

OM-264 359 Page 3

1-3. Engine Hazards

BATTERY EXPLOSION can injure.

 Always wear a face shield, rubber gloves, and

protective clothing when working on a battery.

 Stop engine before disconnecting or connect-

ing battery cables, battery charging cables (if

applicable), or servicing battery.

 Do not allow tools to cause sparks when working on a battery.

 Do not use welder to charge batteries or jump start vehicles un-

less the unit has a battery charging feature designed for this pur-

pose.

 Observe correct polarity (+ and −) on batteries.

 Disconnect negative (−) cable first and connect it last.

 Keep sparks, flames, cigarettes, and other ignition sources

away from batteries. Batteries produce explosive gases during

normal operation and when being charged.

 Follow battery manufacturer’s instructions when working on or

near a battery.

FUEL can cause fire or explosion.

 Stop engine and let it cool off before checking or

adding fuel.

 Do not add fuel while smoking or if unit is near

any sparks or open flames.

 Do not overfill tank — allow room for fuel to expand.

 Do not spill fuel. If fuel is spilled, clean up before starting engine.

 Dispose of rags in a fireproof container.

 Always keep nozzle in contact with tank when fueling.

MOVING PARTS can injure.

 Keep away from moving parts such as fans,

belts, and rotors.

 Keep all doors, panels, covers, and guards

closed and securely in place.

 Stop engine before installing or connecting unit.

 Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

 To prevent accidental starting during servicing, disconnect

negative (−) battery cable from battery.

 Keep hands, hair, loose clothing, and tools away from moving

parts.

 Reinstall doors, panels, covers, or guards when servicing is

finished and before starting engine.

 Before working on generator, remove spark plugs or injectors to

keep engine from kicking back or starting.

 Block flywheel so that it will not turn while working on generator

components.

EXHAUST SPARKS can cause fire.

 Do not let engine exhaust sparks cause fire.

 Use approved engine exhaust spark arrestor in

required areas — see applicable codes.

HOT PARTS can burn.

 Do not touch hot parts bare handed.

 Allow cooling period before working on

equipment.

 To handle hot parts, use proper tools and/or wear heavy, insu-

lated welding gloves and clothing to prevent burns.

STEAM AND HOT COOLANT can burn.

 If possible, check coolant level when engine is

cold to avoid scalding.

 Always check coolant level at overflow tank, if

present on unit, instead of radiator (unless told

otherwise in maintenance section or engine manual).

 If the engine is warm, checking is needed, and there is no over-

flow tank, follow the next two statements.

 Wear safety glasses and gloves and put a rag over radiator cap.

 Turn cap slightly and let pressure escape slowly before

completely removing cap.

Using a generator indoors CAN KILL

YOU IN MINUTES.

 Generator exhaust contains carbon monoxide.

This is a poison you cannot see or smell.

 NEVER use inside a home or garage, EVEN IF

doors and windows are open.

 Only use OUTSIDE and far away from windows, doors, and

vents.

BATTERY ACID can BURN SKIN and EYES.

 Do not tip battery.

 Replace damaged battery.

 Flush eyes and skin immediately with water.

ENGINE HEAT can cause fire.

 Do not locate unit on, over, or near combustible

surfaces or flammables.

 Keep exhaust and exhaust pipes way from

flammables.

1-4. Compressed Air Hazards

COMPRESSED AIR EQUIPMENT can

injure or kill.

 Incorrect installation or operation of this unit

could result in equipment failure and personal

injury. Only qualified persons should install, op-

erate, and service this unit according to its

Owner’s Manual, industry standards, and na-

tional, state, and local codes.

 Do not exceed the rated output or capacity of the compressor or

any equipment in the compressed air system. Design compressed

air system so failure of any component will not put people or prop-

erty at risk.

 Before working on compressed air system, turn off and lockout/

tagout unit, release pressure, and be sure air pressure cannot be

accidentally applied.

 Do not work on compressed air system with unit running unless

you are a qualified person and following the manufacturer’s in-

structions.

 Do not modify or alter compressor or manufacturer-supplied

equipment. Do not disconnect, disable, or override any safety

equipment in the compressed air system.

 Use only components and accessories approved by the manufac-

turer.

 Keep away from potential pinch points or crush points created by

equipment connected to the compressed air system.

 Do not work under or around any equipment that is supported only

by air pressure. Properly support equipment by mechanical

means.

OM-264 359 Page 4

HOT METAL from air arc cutting and

gouging can cause fire or explosion.

 Do not cut or gouge near flammables.

 Watch for fire; keep extinguisher nearby.

COMPRESSED AIR can injure or kill.

 Before working on compressed air system,

turn off and lockout/tagout unit, release pres-

sure, and be sure air pressure cannot be acci-

dentally applied.

 Relieve pressure before disconnecting or con-

necting air lines.

 Check compressed air system components

and all connections and hoses for damage,

leaks, and wear before operating unit.

 Do not direct air stream toward self or others.

 Wear protective equipment such as safety glasses, hearing pro-

tection, leather gloves, heavy shirt and trousers, high shoes, and

a cap when working on compressed air system.

 Use soapy water or an ultrasonic detector to search for

leaks−−never use bare hands. Do not use equipment if leaks are

found.

 Reinstall doors, panels, covers, or guards when servicing is

finished and before starting unit.

 If ANY air is injected into the skin or body seek medical help im-

mediately.

BREATHING COMPRESSED AIR can in-

jure or kill.

 Do not use compressed air for breathing.

 Use only for cutting, gouging, and tools.

TRAPPED AIR PRESSURE AND WHIPPING

HOSES can injure.

 Release air pressure from tools and system be-

fore servicing, adding or changing attach-

ments, or opening compressor oil drain or oil fill

cap.

MOVING PARTS can injure.

 Keep away from moving parts such as fans,

belts and rotors.

 Keep all doors, panels, covers, and guards

closed and securely in place.

 Keep hands, hair, loose clothing, and tools away from moving

parts.

 Before working on compressed air system, turn off and lockout/

tagout unit, release pressure, and be sure air pressure cannot be

accidentally applied.

 Have only qualified people remove guards or covers for maint-

enance and troubleshooting as necessary.

 Reinstall doors, panels, covers, or guards when servicing is

finished and before starting engine.

HOT PARTS can burn.

 Do not touch hot compressor or air system

parts.

 Allow cooling period before working on

equipment.

 To handle hot parts, use proper tools and/or wear heavy, insu-

lated welding gloves and clothing to prevent burns.

READ INSTRUCTIONS.

 Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

 Use only genuine replacement parts from the manufacturer.

 Perform installation, maintenance, and service according to the

Owner’s Manuals, industry standards, and national, state, and

local codes.

1-5. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

 Do not install or place unit on, over, or near

combustible surfaces.

 Do not install unit near flammables.

 Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

FALLING EQUIPMENT can injure.

 Use lifting eye to lift unit and properly installed

accessories only, NOT gas cylinders. Do not

exceed maximum lift eye weight rating (see

Specifications).

 Use equipment of adequate capacity to lift and support unit.

 If using lift forks to move unit, be sure forks are long enough to

extend beyond opposite side of unit.

 Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

 Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94−110) when manu-

ally lifting heavy parts or equipment.

OVERHEATING can damage motors.

 Turn off or unplug equipment before starting or

stopping engine.

 Do not let low voltage and frequency caused by

low engine speed damage electric motors.

 Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle

where applicable.

FLYING SPARKS can injure.

 Wear a face shield to protect eyes and face.

 Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper

face, hand, and body protection.

 Sparks can cause fires — keep flammables away.

MOVING PARTS can injure.

 Keep away from moving parts.

 Keep away from pinch points such as drive

rolls.

OM-264 359 Page 5

BATTERY CHARGING OUTPUT and BATTERY

EXPLOSION can injure.

Battery charging not present on all models.

 Always wear a face shield, rubber gloves, and

protective clothing when working on a battery.

 Stop engine before disconnecting or connecting battery cables,

battery charging cables (if applicable), or servicing battery.

 Do not allow tools to cause sparks when working on a battery.

 Do not use welder to charge batteries or jump start vehicles un-

less it has a battery charging feature designed for this purpose.

 Observe correct polarity (+ and −) on batteries.

 Disconnect negative (−) cable first and connect it last.

 Keep sparks, flames, cigarettes, and other ignition sources

away from batteries. Batteries produce explosive gases during

normal operation and when being charged.

 Follow battery manufacturer’s instructions when working on or

near a battery.

 Have only qualified persons do battery charging work.

 If battery is being removed from a vehicle for charging, discon-

nect negative (−) cable first and connect it last. To prevent an arc,

make sure all accessories are off.

 Charge lead-acid batteries only. Do not use battery charger to

supply power to an extra-low-voltage electrical system or to

charge dry cell batteries.

 Do not charge a frozen battery.

 Do not use damaged charging cables.

 Do not charge batteries in a closed area or where ventilation is

restricted.

 Do not charge a battery that has loose terminals or one showing

damage such as a cracked case or cover.

 Before charging battery, select correct charger voltage to match

battery voltage.

 Set battery charging controls to the Off position before connect-

ing to battery. Do not allow battery charging clips to touch each

other.

 Keep charging cables away from vehicle hood, door, or moving

parts.

HIGH PRESSURE FLUIDS can injure or kill.

 Engine fuel system components can be under

high pressure.

 Before working on fuel system, turn off engine

to release pressure.

 If any fluid is injected into the skin or body seek medical help im-

mediately.

WELDING WIRE can injure.

 Do not press gun trigger until instructed to do

so.

 Do not point gun toward any part of the body,

other people, or any metal when threading

welding wire.

OVERUSE can cause OVERHEATING.

 Allow cooling period; follow rated duty cycle.

 Reduce current or reduce duty cycle before

starting to weld again.

 Do not block or filter airflow to unit.

STATIC (ESD) can damage PC boards.

 Put on grounded wrist strap BEFORE handling

boards or parts.

 Use proper static-proof bags and boxes to

store, move, or ship PC boards.

TILTING OF TRAILER can injure.

 Use tongue jack or blocks to support weight.

 Properly install welding generator onto trailer

according to instructions supplied with trailer.

READ INSTRUCTIONS.

 Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

 Use only genuine replacement parts from the manufacturer.

 Perform installation, maintenance, and service according to the

Owner’s Manuals, industry standards, and national, state, and

local codes.

H.F. RADIATION can cause interference.

 High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

 Have only qualified persons familiar with

electronic equipment perform this installation.

 The user is responsible for having a qualified electrician

promptly correct any interference problem resulting from the

installation.

 If notified by the FCC about interference, stop using the

equipment at once.

 Have the installation regularly checked and maintained.

 Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

 Electromagnetic energy can interfere with

sensitive electronic equipment such as micro-

processors, computers, and computer-driven

equipment such as robots.

 Be sure all equipment in the welding area is electromagnetically

compatible.

 To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

 Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

 Be sure this welding machine is installed and grounded

according to this manual.

 If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

OM-264 359 Page 6

1-6. California Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases

which contain chemicals known to the State of California to

cause birth defects and, in some cases, cancer. (California

Health & Safety Code Section 25249.5 et seq.)

Battery posts, terminals and related accessories contain lead

and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

This product contains chemicals, including lead, known to

the state of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after use.

For Gasoline Engines:

Engine exhaust contains chemicals known to the State of

California to cause cancer, birth defects, or other reproduc-

tive harm.

For Diesel Engines:

Diesel engine exhaust and some of its constituents are

known to the State of California to cause cancer, birth

defects, and other reproductive harm.

1-7. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

is available as a free download from the American Welding Society at

http://www.aws.org or purchased from Global Engineering Documents

(phone: 1-877-413-5184, website: www.global.ihs.com).

Safe Practices for the Preparation of Containers and Piping for Welding

and Cutting, American Welding Society Standard AWS F4.1, from Glob-

al Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

Safe Practices for Welding and Cutting Containers that have Held Com-

bustibles, American Welding Society Standard AWS A6.0, from Global

Engineering Documents (phone: 1-877-413-5184,

website: www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:

www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 14501 George Carter Way,

Suite 103, Chantilly, VA 20151 (phone: 703-788-2700,

website:www.cganet.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2, from Canadian Standards Association, Standards Sales, 5060

Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5NS

(phone: 800-463-6727, website: www.csagroup.org).

Battery Chargers, CSA Standard C22.2 NO 107.2−01, from Canadian

Standards Association, Standards Sales, 5060 Spectrum Way, Suite

100, Mississauga, Ontario, Canada L4W 5NS (phone: 800-463-6727,

website: www.csagroup.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.)

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—

phone for Region 5, Chicago, is 312-353-2220, website:

www.osha.gov).

Portable Generators Safety Alert, U.S. Consumer Product Safety Com-

mission (CPSC), 4330 East West Highway, Bethesda, MD 20814

(phone: 301-504-7923, website: www.cpsc.gov).

Applications Manual for the Revised NIOSH Lifting Equation, The Na-

tional Institute for Occupational Safety and Health (NIOSH), 1600

Clifton Rd, Atlanta, GA 30329-4027 (phone: 1-800-232-4636, website:

www.cdc.gov/NIOSH).

1-8. EMF Information

Electric current flowing through any conductor causes localized electric

and magnetic fields (EMF). The current from arc welding (and allied pro-

cesses including spot welding, gouging, plasma arc cutting, and

induction heating operations) creates an EMF field around the welding

circuit. EMF fields can interfere with some medical implants, e.g. pace-

makers. Protective measures for persons wearing medical implants

have to be taken. For example, restrict access for passers−by or con-

duct individual risk assessment for welders. All welders should use the

following procedures in order to minimize exposure to EMF fields from

the welding circuit:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Do not place your body between welding cables. Arrange cables

to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep head and trunk as far away from the equipment in the

welding circuit as possible.

5. Connect work clamp to workpiece as close to the weld as possi-

ble.

6. Do not work next to, sit or lean on the welding power source.

7. Do not weld whilst carrying the welding power source or wire

feeder.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating operations.

If cleared by your doctor, then following the above procedures is recom-

mended.

Page is loading ...

OM-264 359 Page 13

 Veiller à ce que ce poste de soudage soit posé et mis à la terre

conformément à ce mode d’emploi.

 En cas d’interférences après avoir pris les mesures précédentes,

il incombe à l’utilisateur de prendre des mesures supplémentaires

telles que le déplacement du poste, l’utilisation de câbles blindés,

l’utilisation de filtres de ligne ou la pose de protecteurs dans la zone

de travail.

2-6. Proposition californienne 65 Avertissements

Les équipements de soudage et de coupage produisent des

fumées et des gaz qui contiennent des produits chimiques

dont l’État de Californie reconnaît qu’ils provoquent des mal-

formations congénitales et, dans certains cas, des cancers.

(Code de santé et de sécurité de Californie, chapitre 25249.5

et suivants)

Les batteries, les bornes et autres accessoires contiennent

du plomb et des composés à base de plomb, produits chim-

iques dont l’État de Californie reconnaît qu’ils provoquent

des cancers et des malformations congénitales ou autres

problèmes de procréation. Se laver les mains après

manipulation.

Ce produit contient des produits chimiques, notamment du

plomb, dont l’État de Californie reconnaît qu’ils provoquent

des cancers, des malformations congénitales ou d’autres

problèmes de procréation. Se laver les mains après

utilisation.

Pour les moteurs à essence :

Les gaz d’échappement des moteurs contiennent des pro-

duits chimiques dont l’État de Californie reconnaît qu’ils

provoquent des cancers et des malformations congénitales

ou autres problèmes de procréation.

Pour les moteurs diesel :

Les gaz d’échappement des moteurs diesel et certains de

leurs composants sont reconnus par l’État de Californie

comme provoquant des cancers et des malformations con-

génitales ou autres problèmes de procréation.

2-7. Principales normes de sécurité