Simplicity 071027-0 User manual

Models 071026 & 071027

202212GS Rev. - (1/11/2007)

100 Amp / 200 Amp

Automatic Transfer Switch

Installation and Operator’s Manual

TS100A and TS200A

Questions?

Help is just a moment away!

Call: Transfer Switch Helpline

(877) 369-9400 M-F 8-5 CT

Rheem Sales Company

Randleman, NC 27317

(877) 369-9400

reserved. No part of this material may be reproduced or

transmitted in any form by any means without the express

written permission of Rheem Sales Company.

Thank you for your purchase of this Rheem/Ruud Automatic Transfer Switch. This product is intended for use with Rheem

and Ruud Home Standby Generator sets ONLY. This is an optional home standby system which provides an alternate source

of electric power and to serve loads such as a gas furnace, refrigeration and communication systems that, when stopped

during any power outage, could cause discomfort, or the like.

This manual contains safety information to make you aware of the hazards and risks associated with transfer switches and

how to avoid them. Rheem has made every effort to provide for a safe, streamlined and cost-effective installation. Each

installation is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation

might be achieved. We do not know all possible hazards and/or the results of each method or procedure. Save these

instructions for future reference.

This transfer switch requires installation before use. Refer to the Installation section of this manual for instructions on

installation procedures. Only licensed electrical contractors should install transfer switches. Installations must strictly

comply with all applicable federal, state and local codes, standards and regulations.

Where to Find Us

You never have to look far to find support and service for your transfer switch. Consult your Yellow Pages. There are many

Rheem and Ruud authorized service dealers who provide quality service. You can also contact Rheem/Ruud Customer Service

by phone at (877) 369-9400.

Transfer Switch

Model Number

Revision

Serial Number

Date Purchased

1
FrançaisEspañol
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Owner Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installer Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power Wiring Interconnections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Supervisory Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
System Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Testing the Automatic Transfer Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Schematic & Wiring Diagram, Models TS100A and TS200A . . . . . . . . 10-11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table of Contents

2

Important Safety Instructions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the transfer switch unsafe.

Save These Instructions

• Use transfer switch only for intended uses.

• If you have questions about intended use, ask dealer or contact

Rheem.

• Do not expose transfer switch to excessive moisture, dust, dirt,

or corrosive vapors.

• Remain alert at all times while working on this equipment. Never

work on the equipment when you are physically or mentally

fatigued.

• If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

NOTICE

Improper treatment of transfer switch can damage it and

shorten its life.

• Do not touch bare wires.

• Do not use transfer switch with worn, frayed, bare or otherwise

damaged wiring.

• Do not handle electrical cords while standing in water, while

barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service transfer switch.

• In case of an accident caused by electrical shock, immediately

shut down all sources of electrical power and contact local

authorities. Avoid direct contact with the victim.

WARNING

Failure to properly ground transfer switch can

result in electrocution.

• Despite the safe design of the transfer switch, operating this

equipment imprudently, neglecting its maintenance or being

careless can cause possible injury or death.

WARNING

Transfer switch contains high voltage that can

cause personal injury or death.

• Failure to follow above warning could cause personal injury,

damage and/or malfunction of equipment.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

WARNING

Only qualified electricians should attempt installation of

this system, which must strictly comply with applicable

codes, standards and regulations.

3

Introduction

Your Rheem Transfer Switch is supplied with this combined

“Installation and Operator’s Manual”. This is an important

document and should be retained by the owner after the

installation has been completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change, alter

or otherwise improve the system at any time without prior

notice.

For the Home Owner

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the Owner Orientation Section

of this manual BEFORE contracting or starting your

transfer switch installation.

To arrange for proper installation, contact the store at which

you purchased your Rheem Transfer Switch, your dealer, or

your utility power provider.

The Transfer Switch Warranty is VOID

unless the system is installed by a

licensed electrical professional.

Owner Orientation

The illustrations are for typical circumstances and are meant

to familiarize you with the installation options available with

your transfer switch.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must be

allowed for. This is necessary to comply with local codes and

overcome electrical voltage drops.

The factors mentioned above will have a direct effect

on the overall price of your transfer switch installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

transfer switch, as specified in the manual.

Installer Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• Check federal, state and local codes and authority

having jurisdiction, for questions on installation.

• Ensure generator is not overloaded with selected loads.

If you need more information about the transfer switch, call

(877) 369-9400, between 8:00 AM and 5:00 PM CT.

Equipment Description

These transfer switches are intended to transfer the entire

electrical load of normal residential installations when used

with the supervisory contacts provided. The load is

connected either to utility power (normal) or home standby

power (generator). The transfer switch monitors utility and

generator voltages and will automatically connect to the

appropriate source of power.

Major components of the transfer switch are a 2 pole double

throw transfer switch, control circuit board, fused utility

terminals and interconnecting wiring. The control board also

has two inputs for current transformers used to sense

generator current.

The transfer switch is solenoid-operated from utility or

generator inputs and contains suitable mechanical and

electrical interlock switches to eliminate the possibility of

connecting the utility service to the generator output. It has

ratings capable of switching full utility power into the

residence. In addition, a manual override lever is provided

for the transfer function.

The control circuit board has active circuits sensing utility

and generator voltages. It creates a signal for the generator

start-up, switch transfer, and retransfer when utility is

restored. The control board also contains red and green

LED’s indicating the power sources available and two relay

operated contacts that provide supervisory control of

external loads.

4

Installation

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the transfer

switch components for any damage that may have occurred

during shipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor's

memo of loss or damage. If loss or damage is noted after

delivery, contact the carrier for claim procedures. Missing or

damaged parts are not warranted.

Shipment Contents

• Automatic Power Transfer Switch

• Two Current Transformers

• Installation and Operator’s Manual

Mounting Guidelines

The Automatic Transfer Switch is enclosed in NEMA Type 3R

enclosures suitable for indoor or indoor/outdoor use.

Guidelines for mounting the Automatic Transfer Switch

include:

• Install the switch on a firm, sturdy supporting

structure.

• The switch must be installed with minimum NEMA 3R

hardware for conduit connections.

• To prevent switch contact distortion, level and plumb

the enclosure. This can be done by placing washers

between the switch enclosure and the mounting

surface.

• Never install the switch where any corrosive substance

might drip onto the enclosure.

• Protect the switch at all times against excessive

moisture, dust, dirt, lint, construction grit and corrosive

vapors.

A typical installation of the Automatic Power Transfer Switch

for Models TS100A and TS200A is depicted in Figure 1. An

alternative installation of the Automatic Power Transfer

Switch is depicted in Figure 2.

It is best if the transfer switch is mounted near the utility

watt-hour meter, either inside or outside. Discuss layout

suggestions/changes with the owner before beginning the

system installation process.

5

Main

Circuit

Breaker

Panel

Transfer

Switch

Hot Water

Heater

Air

Conditioner

Contactor

Generator

Watt -

Hourmeter

Branch Circuits

— — — — — — Control Wiring

Disconnect Switch

Service

Disconnect

Main

Circuit

Breaker

Panel

Transfer

Switch

Hot Water

Heater

Air

Conditioner

Contactor

Disconnect Switch

Generator

Watt -

Hourmeter

Branch

Circuits

Emergency

Branch

Circuits

— — — — — — Control Wiring

Emergency

Load Center

Figure 1 - Typical Transfer Switch Mounting for Models TS100A and TS200A

Figure 2 - Alternate Transfer Switch Mounting

6

Power Wiring Interconnections

All wiring must be the proper size, properly supported and

protected by conduit.

Complete the following connections between the transfer

switch, main distribution panel, utility power and generator,

as shown in Figure 3.

1. Ensure utility power is turned OFF. Connect utility

feeder conductors to transfer switch terminals marked

“UTILITY CONNECTION”.

2. Connect utility Neutral conductor to the transfer switch

“NEUTRAL” terminal.

3. Connect main breaker panel feeder conductors to

transfer switch terminals marked “LOAD

CONNECTION”.

4. Connect main breaker panel Neutral conductor to

transfer switch “NEUTRAL” terminal.

5. Connect main breaker panel Ground conductor to the

transfer switch “GND” terminal.

NOTE: Assure grounding electrode conductor is connected

and bonded per applicable federal, state and local codes,

standards and regulations.

6. Connect generator feeder conductors from the

generator control panel to transfer switch terminals

marked “GENERATOR CONNECTION” Each conductor

should pass through hole of current transformer before

making connection.

7. Plug in current transformer leads into “CT1” and “CT2”

on control module.

• Failure to follow above warning could cause personal injury,

damage and/or malfunction of equipment.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

Figure 3 - Typical Installation Diagram for Model TS100A & TS200A Transfer Switches

Main

Main Breaker Panel

Ground Bus

Neutral

Bus

To Generator

Neutral

Terminal

To Utility Meter

Supervisory

Contacts

Load

Connection

Ground

Terminal

Generator

Connection

Utility

Connection

7

8. Connect Neutral conductor from the generator control

panel to the transfer switch “NEUTRAL” terminal.

9. Connect generator Ground conductor from the control

panel to the transfer switch “GND” terminal.

NOTE: Assure generator equipment grounding conductor is

connected per applicable federal, state and local codes,

standards and regulations.

10. Connect generator “UTILITY 240 VAC” terminals to

transfer switch “UTILITY 240 VAC” terminals. Use

minimum #14 AWG conductors.

11. Tighten all wire connections/fasteners to proper torque.

See inside transfer switch enclosure for proper torque

values.

Supervisory Control Wiring

1. Terminal strip on control module in transfer switch has

four connections for customer use. There are two sets

of “Normally Closed” contacts available. They will be

activated when generator power is required. These can

be used for supervisory control of large connected

loads on generator. Loads will be allowed to operate if

there is enough generator power available.

NOTE: There are two wireways provided to keep the

supervisory loads separated from each other.

2. Terminals “A-A” on control module are rated for 24 VAC

and air conditioner contactor control. Contacts are

connected in series with the air conditioner contactor

control circuit (Figure 4).

3. Terminals “B-B” on control module are rated for 1 Amp

125 VAC and installer supplied contactor to control a

large load. Example: electric hot water heater. Contacts

are connected in series with the contactor control

circuit (Figure 5).

4. Tighten all wire connections/fasteners to proper torque.

See inside transfer switch enclosure for proper torque

values.

System Setup

You must perform the following on the control module

before operating the system:

• If generator is installed in an area regularly subjected to

temperatures below 40°F (4°C), select a 50 second

warm up time by moving jumper installed on JP2

(Figure 6) from ‘20’ position to ‘50’ position.

• Place 2 position switch (Figure 6) in ‘NG’ or ‘LP’

position, whichever is appropriate for your system.

• Place 3 position switch (Figure 6) to match KW rating

of installed generator.

Controls

Other than a Manual Override lever, there are no operator

controls because this is an automatic transfer switch. The

manual override is to be used only by licensed professionals.

Figure 5 — Terminals “B-B”

B

Figure 4 — Terminals “A-A”

Contactor

Neutral

120 VAC

Air Conditioner Contactor

24 VAC

A

Figure 6 — Control Module

2 Position

Switch

3 Position

Switch

JP2

CT1 & CT2

Connectors

Supervisory

Contacts

8

Operation

To select automatic transfer operation, do the following:

1. For models TS100A & TS200A, set disconnect switch

that sends utility power to transfer switch to “On”

position. This switch is probably located in the main

breaker panel.

2. Set generator main circuit breaker to its “On” position.

3. Install 15 Amp fuse in generator control panel.

4A. If generator is equipped with a system ON/OFF switch,

set switch to “On” position.

4B. If generator is equipped with a AUTO/OFF/MANUAL

switch, set switch to “AUTO” position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer

switch, the control module is constantly monitoring

generator power. If the air conditioner is called to run, and

there is sufficient generator power available, the control

module will close contacts “A-A” to air conditioner contactor.

Contacts “B-B” will open before contacts A-A close. If loads

are too great for generator, contacts A-A and/or B-B will

open. When air conditioning is not needed, A-A will open. If

enough power is available, B-B will close.

Testing the Automatic Transfer Switch

Turn the disconnect switch feeding the transfer switch

contactor to the “Off” position. The Automatic Sequence of

the system will follow. To go back to utility power, turn the

disconnect to the “On” position.

Automatic Sequence

Utility Fail

The Home Standby Generator set senses when utility voltage

is below 70 percent of nominal. Engine start sequence is

initiated after 6 second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer fixed

at 20 seconds or 50 seconds with removal of jumper on

control board (see System Setup).

Transfer

Transfer from utility to generator supply occurs after voltage

is above set levels. Minimum engine run time is 5 minutes

after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility supply is approximately

10 seconds after utility voltage supply is above utility pickup

level and minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

9

Maintenance

The transfer switch is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the transfer switch clean.

Visual inspections should be done at least once a month.

Access to transfer switch must not be obstructed. Keep

3 feet (1 m) clearance around transfer switch. Check for an

accumulation of dirt, moisture and/or corrosion on and

around the enclosure, loose parts/hardware, cracks and/or

discoloration to insulation, and damaged or discolored

components.

Exercise the transfer switch at least once every three months

as described in section Testing the Automatic Transfer

Switch unless a power outage occurs and home generator

system has gone through an automatic sequence. Allow

generator to run for at least 30 minutes.

Contact a licensed electrical professional to inspect and clean

the inside of your transfer switch at least once a year.

Specifications

UL® 1008 Listed Transfer Switch

Model TS100A

Maximum Load Current . . . . . . . . . . . . . . . . . . . . .100 Amps

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50/60 Hz

Fault Current Rating . . . .22,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . .24 Volt AC

B-B Terminals . . . . . . . . . .1 Amp, 125 Volt AC, Pilot Duty

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 lbs.

Model TS200A

Maximum Load Current . . . . . . . . . . . . . . . . . . . . .200 Amps

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .250 Volts

Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50/60 Hz

Fault Current Rating . . . .25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . .24 Volt AC

B-B Terminals . . . . . . . . . .1 Amp, 125 Volt AC, Pilot Duty

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 lbs.

Page is loading ...

11

Wiring Diagram, Models TS100A and TS200A

12

Troubleshooting

Problem Cause Correction

Automatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Reset generator circuit breaker.

2. Refer to generator manual.

Automatic transfer switch does not

transfer to utility

1. Service disconnect breaker open.

2. Utility voltage not acceptable.

1. Reset service disconnect breaker.

2. Wait for utility voltage to return to

normal.

Generator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Supervised loads (air conditioner, etc.)

are not operating when generator is

supplying power

1. A-A or B-B contacts not operating

correctly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Check A-A or B-B contacts for

proper operation and/or check

control wiring to external load.

2. Decrease load to generator.

3. Plug CT connectors into control

board.

4. Contact local service center.

Generator is still running after utility

power is restored

1. Minimum engine run time has not

elapsed.

2. Fuse(s) in transfer switch is

defective.

1. Wait five minutes for transfer switch

to retransfer to utility power.

2. Check fuse(s) and replace if

necessary.

Warranty

13

PROTECH™ Residential Standby Generators

Models: GEN12S GEN15S GEN20B GEN25B GEN30B

SCOPE of WARRANTY:

· This Limited Warranty provides that a replacement will be furnished for any part of the product which fails in normal use and service during the

Applicable Warranty Period specified, in accordance with the warranty’s terms. The replacement part is warranted for only the unexpired portion of the

original Applicable Warranty Period.

EXCEPTIONS:

· Commercial applications are not covered.

· Units installed as prime power source are not covered.

· Installations for the purpose of life support situations are not covered.

EFFECTIVE DATE of WARRANTY COVERAGE:

The Effective Date is the date of installation if properly documented; otherwise it is the date of manufacture plus six (6) months.

APPLICABLE WARRANTY PERIODS for VARIOUS PARTS:

All Residential Standby Generator Parts are warranted for an Applicable Warranty Period of Four (4) YEARS or 1500 operating hours, whichever occurs

first, after the Effective Date, except for the following specified product parts.

Transfer Switches - Transfer Switches (TS-100 and TS-200) carry a 3 year warranty for all parts.

Engine - The Briggs & Stratton engine warranty is covered by the manufacturer. Refer to Vanguard manual MS-3235

STANDARD PROVISIONS and CONDITIONS:

EXCLUSIONS - THIS WARRANTY WILL NOT APPLY: a) to damages, malfunctions or failures resulting from failure to properly install, operate or maintain the

unit in accordance with the manufacturer’s instructions provided; b) to damages, malfunctions or failures resulting from abuse, accident, fire, flood and

the like; c) to parts used in connection with normal maintenance, such as adjustments, fuel system cleaning and obstruction due to chemical, dirt,

carbon, lime and so forth; d) to units which are not installed in the United States of America or Canada; e) to units which are not installed in accordance

with applicable local codes, ordinances and good trade practices; f) to damages, malfunctions or failures caused by the use of any attachment,

accessory or component not authorized by the manufacturer; g) to wear items such as oil gauges, o-rings, filters fuses, or spark plugs etc.

SHIPPING COSTS: This Warranty does NOT cover shipping costs. You will be responsible for the cost of shipping warranty replacement parts from our factory

to our distributor and from the distributor to the location of your product. You also are responsible for any shipping cost of returning the failed part to

the distributor.

SERVICE LABOR RESPONSIBILITY: This Warranty does NOT cover any labor expenses for service, NOR for removing or reinstalling parts. All such expenses

are your responsibility, unless a service labor agreement exists between you and your contractor.

HOW TO OBTAIN WARRANTY PERFORMANCE: You must promptly report any failure covered by this warranty to the installing contractor or distributor.

Normally, the installing contractor from whom the unit was purchased will be able to take the necessary corrective action by obtaining through his

distributor any replacement parts. If the contractor is not available, simply contact any other local contractor handling RHEEM, RUUD or PROTECH air

conditioning products. The name and location of a local contractor can usually be found in your telephone directory or by contacting a RHEEM, RUUD

or PROTECH air conditioning distributor. If necessary, the following office can advise you of the nearest distributor:

4744 Island Ford Road, Randleman, NC 27317

HOWEVER, ANY REPLACEMENTS ARE MADE SUBJECT TO VALIDATION OF IN-WARRANTY COVERAGE. An item to be replaced must be made available

in exchange for the replacement.

EXCLUSIVE WARRANTY - LIMITATION OF LIABILITY:

This Limited Warranty is the ONLY warranty for the unit given by the manufacturer. No one is authorized to make any warranties on their behalf. ANY

IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE

APPLICABLE WARRANTY PERIODS SPECIFIED ABOVE. RHEEM’S SOLE LIABILITY WITH RESPECT TO DEFECTIVE PARTS OR FAILURES SHALL BE AS

SET FORTH IN THIS LIMITED WARRANTY, AND ANY CLAIMS FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXPRESSLY EXCLUDED. Some

states do not allow limitations on how long an implied warranty lasts, or for the exclusion of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

202249E, Rev. -, 1/3/2007

RHEEM SALES COMPANY

Randleman NC

“In the spirit of continuous improvement, we reserve the right to make changes without notice.”

Page is loading ...