Pioneer CD-BTB100 is a Bluetooth adapter that allows you to connect your mobile phone or other Bluetooth-enabled devices to your car stereo. It supports Bluetooth 1.1 with HFP and OPP profiles, enabling you to make and receive calls, as well as stream audio from your phone to your car speakers. The CD-BTB100 also features a built-in microphone for hands-free calling.
Pioneer CD-BTB100 is a Bluetooth adapter that allows you to connect your mobile phone or other Bluetooth-enabled devices to your car stereo. It supports Bluetooth 1.1 with HFP and OPP profiles, enabling you to make and receive calls, as well as stream audio from your phone to your car speakers. The CD-BTB100 also features a built-in microphone for hands-free calling.
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2006
CRT3686
BLUETOOTH ADAPTER
CD-BTB100
/XN/EW5
This service manual should be used together with the following manual(s) listed below.
For the parts numbers, adjustments, etc. which are not shown in this manual,
refer to the following manual(s).
Model No. Order No. Mech. Module Remarks
CD-BT10/XN/EW5 CRT3625
K-ZZD. APR. 2006 Printed in Japan
CD-BTB100
/XN/E
CD-BTB100/XN/EW52
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
EXPLODED VIEWS AND PARTS LIST
PACKING(Page 6)
PACKING SECTION PARTS LIST
*:Non spare part
Owner's Manual
EXTERIOR(Page 8)
EXTERIOR SECTION PARTS LIST
Mark No. Description CD-BT10/XN/EW5 CD-BTB100/XN/EW5 CD-BTB100/XN/E
8 Carton CHG5864 CHG5865 CHG5758
9 Contain Box CHL5864 CHL5865 CHL5758
* 16 Caution Card CRP1338 CRP1341 CRP1341
* 17 Warranty Card CRY1157 CRY1157 CRY1246
Owner’s Manual Not used CRD4103 CRD4105
Owner’s Manual Not used CRD4104 Not used
Part No. Language
CRD4103 English, Spanish, German, French
CRD4104 Italian, Dutch, Russian
CRD4105 English, French, Portuguese(B)
Mark No. Description CD-BT10/XN/EW5 CD-BTB100/XN/EW5 CD-BTB100/XN/E
7 Main Unit Assy CWN1932 CWN1933 CWN1933
17 Bluetooth Unit CWN1934 CWN1935 CWN1935
25 Plate Unit CXC6643 CXC6642 CXC6642
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
CD-BTB100/XN/EW5 3
5 678
5678
C
D
F
A
B
E
ADJUSTMENT
BLUETOOTH TEST MODE
CD-BTB100/XN/EW54
1234
1234
C
D
F
A
B
E
- Check in Normal Operation
0. Bluetooth phone specifications
A mobile phone supporting Bluetooth Ver.1.1 with HFP and OPP is required.
Models with which connection has been verified are recommended.
When AV profile device is used,
When AV profile device is used, models with which connection has been verified are recommended.
[naviPlay Adapter (TEN_Technorogy), BLUEWAVE (macally), IPBCK (SCOSCHE),
BT-01UDE (PLANEX), wireless headphones (Logicool), etc]
1. Caution
Explain to the user that the user registration data on Flash ROM memory will be deleted to clear the history of
connection test. Then turn the ACC ON and press the reset button to delete the Flash ROM memory.
2. Outline of functions
Check the connection in normal operation when checking the operation using phones
supporting Bluetooth.
3. Configuration diagram
CD-BTB100
Bluetooth
IP-BUS
Head unit (DEH-P7700MP, etc.)
Bluetooth AUDIO
Mobile Phone
CD-BTB100/XN/EW5 5
5 678
5678
C
D
F
A
B
E
4. Procedure for checking connection with Bluetooth-supporting phones
Operation Method Screen
Execute Bluetooth device search by operating
the mobile phone and input the pass key.
5. Procedure for checking connection with Bluetooth-supporting AUDIO devices
Operation Method Screen
Operate the Bluetooth AUDIO device and
establish
Bluetooth connection.
When connection is completed, screen
display on the right appears.
Select FUNC1 from the FUNCTION menu
and register the phone data by pressing
registration key to show the screen on the
right.
When phone data is registered, its incoming
and outgoing call register, etc. can be
displayed.
When connection with Bluetooth phone is
complete,
the screen display shown on the right
appears.
When connection is successful, execute
calling test and check the voice
↓
↓
↓
6. Waiting for connection with Bluetooth-supporting devices
Operation Method Screen
By selecting FUNC1 on the FUNCTION
menu and pressing the registration key,
the product waits for connection
establishment (right figure).
CD-BTB100/XN/EW56
1234
1234
C
D
F
A
B
E
- Test Mode (using mobile phones)
1. Outline
A test mode for simply checking the following 3 items.
• Bluetooth antenna sensitivity check
• FLASH memory operation check
• Bluetooth connection (authenticated connection) check
2. Configuration diagram for testing
IP-BUS Bluetooth
3. Procedure for starting up the test mode
Start up the power supply by simultaneously pressing 4+6 keys and set the H/U mode
into test mode.
CN :WA I T
Connection waiting status
Connecting from the mobile phone (PIN input)
CN : OK CN : ERROR
Connection completion status Connection error
Key 1 pressing
AN : - - -
Detecting antenna strength
AN : - 1 5
Display of antenna strength (when it is -15 dB (the range is -18 dB to -80 dB))
Key 1 pressing
Note: This function is not
used in service.
SND : OFF Voice line is not connected.
Voice link cutoff status
Key 1 pressing
SND : ON SND : NG Voice line is connected.
Check that sine wave is input
from the microphone and is
output from the speaker.
Voice link ON: Outputting sine wave Voice link NG
Key 1 pressing
SND : OFF Voice line is cut off.
Check that the sine wave stops.
Voice link cutoff status
Key 1 pressing
FLASH: - - FLASH check is executed automatically by the following order.
Deleting→writing→reading→deleting all→reading
When FLASH memory test is executed,
user registration data on FLASH memory is deleted.
Test is completed if operation is normal to this point.
Testing Flash memory
FLASH:OK FLASH:NG
Flash memory test OK Flash memory test NG
CD-BTB100/XN/EW5 7
5 678
5678
C
D
F
A
B
E
- Test mode (using spectrum analyzer)
1. Cautions
If there is a spectrum analyzer supporting 2.4 GHz at the service site, confirmation of
transmission carrier becomes possible.
Since CD-BTB100 cannot operate singly, the main set with IP-BUS control is required.
Carrier existence is checked by removing the product case and applying the probe onto
the "ANT" land of the base unit.
Since it is done by probe connection, the level cannot be confirmed accurately.
2. Function outline
Simple operation check on Bluetooth is executed in test mode using a spectrum analyzer
supporting 2.4 GHz.
Output check on Bluetooth unit
3. Configuration diagram
Spectrum analyzer supporting 2.4 GHz
4. Procedure for test mode startup
1. Test mode startup
Start up the power supply by
simultaneously pressing 4+6 keys and
set the Head Unit mode to test mode.
2. Mode switching
Use the BAND/ key to switch from
production engineering test mode
to authentication/design test mode.
3. Display switches as
shown on the left figure
Switch display using the right key
and set the 5 Local TX no modula-
tion test mode.
Use key 1 to set the Local TX no
modulation detail setup mode.
4. To Local TX no modulation
detail mode
Use key 3 to switch the frequency.
"Transition of display"
"Transition of display"
"Operation"
"Operation"
CN :WA I T
Initial screen for production engineering test mode
BAND key
LOOP . B_S
Initial screen for authentication/design test mode
Local TX no modulation detail setting
TX Frequency
T_2402
Key 3 Key 4
T_2
T_2
T_2
4
4
4
4
8
9
1
0
5
1 Loop Back test:
LOOP . B_S
Right keyLeft key
2 Page Scan test:
P . SCAN_S
3 Inquiry Scan test:
I . SCAN_S
4 Local TX test:
L.TX _S
5 Local TX no modulation test:
Selecting
Local TX no modulation test:
Executing
L.TXNM_S L.TXNM_E
Key 1
Key 2
To Loop Back test
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Pioneer CD-BTB100 is a Bluetooth adapter that allows you to connect your mobile phone or other Bluetooth-enabled devices to your car stereo. It supports Bluetooth 1.1 with HFP and OPP profiles, enabling you to make and receive calls, as well as stream audio from your phone to your car speakers. The CD-BTB100 also features a built-in microphone for hands-free calling.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Pioneer DEH-P4050UB User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Baldwin Boxall BT10 Operating instructions
-
Sony VPL-ES5 User manual
-
-
Sony VPL-EW5 Owner's manual
-
-
Sony VPL-EX50 Product information
-
Magnetrol Series B73 Operating instructions
-
Creda T522VW Instruction book
-
Helvest BT10 User manual
-
Cisco S45IPBK9-12225SG= Datasheet
