SoClean PNA1210-G23 Cleaning Adapter Operating instructions

Type
Operating instructions

SoClean PNA1210-G23 Cleaning Adapter is designed to work with ResMed AirSense 10 CPAP machines to provide daily automated cleaning and disinfection of your CPAP equipment.

Key Capabilities:

  • Connects to the water chamber of your ResMed AirSense 10 machine, replacing the original lid.
  • Uses activated oxygen (ozone) to kill up to 99.9% of bacteria, viruses, mold, and allergens from your CPAP mask, tubing, and water chamber.
  • Eliminates the need for manual cleaning and soaking, saving you time and effort.
  • Helps maintain optimal performance of your CPAP equipment, ensuring a cleaner and more effective therapy experience.

SoClean PNA1210-G23 Cleaning Adapter is designed to work with ResMed AirSense 10 CPAP machines to provide daily automated cleaning and disinfection of your CPAP equipment.

Key Capabilities:

  • Connects to the water chamber of your ResMed AirSense 10 machine, replacing the original lid.
  • Uses activated oxygen (ozone) to kill up to 99.9% of bacteria, viruses, mold, and allergens from your CPAP mask, tubing, and water chamber.
  • Eliminates the need for manual cleaning and soaking, saving you time and effort.
  • Helps maintain optimal performance of your CPAP equipment, ensuring a cleaner and more effective therapy experience.
LID ADAPTER FOR USE WITH
RESMED AIRSENSE 10
INSTRUCTIONS
PNA1210-G23
ResMed Airsense 10 Adapter
Installation Instructions
If you need help connecting
your adapter, contact SoClean.
866-501-3705 | SoClean.com | [email protected]
For SoClean operation information,
please see the User Manual
provided with the device.
An electronic version of the User
Manual is available at SoClean.com
or you may contact Customer Care.
SoClean is an independent company not aliated with ResMed. Names and associated
trademarks are solely owned by the respective companies and manufacturers. Depictions
of brand logos on our website are for informational and educational purposes only and are
used for customer equipment recognition. We are not aliated or endorsed by any sleep
equipment manufacturer.
SoClean Adapter
[Replaces the reservoir lid]
If you are a SoClean 2 user:
Ozone Tube
Injection Fitting
Check Valve
Detach Ozone Tube from
Injection Fitting or your
previous SoClean Adapter.
Save Injection Fitting in case
you need it in the future.
Move on to Step 1.
This end of the Ozone
Tube connects to the
SoClean Adapter
This end of the Ozone
Tube is pre-connected
to the back of the
SoClean 2 unit.
If you are a SoClean 3 user, move on to Step 1.
Remove the Original
Lid from the sleep
equipment reservoir
base by opening the
Original Lid fully,
pushing one side
of the hinge tab
outward, and freeing
the Original Lid from
the base.
Remove the reservoir
from the sleep
equipment machine.
2
Original Lid
Hinge Tab
1
Save the Original Lid and Gasket in case it is needed in
the future.
Install the SoClean
Adapter to the reservoir
base by inserting the
hinge pins into the
notches on the reservoir
base. If needed, insert
one hinge pin at a time
and gently flex the
SoClean Adapter to
snap it in place.
3
SoClean
Adapter
Hinge Pin
When using your
reservoir, fill with distilled
water to the level
indicated by the sleep
equipment manufacturer.
Close the SoClean
Adapter and insert the
reservoir into your sleep
equipment unit like you
normally would.
4
Ozone
Port Cap
WARNING: Ensure sleep equipment hose and SoClean
Adapter are connected to the sleep equipment machine
prior to operating a SoClean Cycle.
WARNING: The Ozone Tube should always be connected
to the SoClean Adapter and the back of the SoClean
unit when operating the SoClean.
NOTE: The SoClean Adapter can be left connected to
your sleep equipment machine after initial setup. You do
not need to disconnect the SoClean Adapter to operate
either the sleep equipment machine or the SoClean.
Uncap the Adapter Ozone Port. Connect the Ozone
Tube to the SoClean Adapter by pushing the Ozone
Tube onto the Adapter Ozone Port.
5
Adapter
Ozone Port
Ozone
Tube
IMPORTANT: Once the adapter is installed, it is your new
permanent lid. If you need to disconnect the SoClean from
your adapter for travel, simply disconnect the ozone tube
from the adapter and re-cap the ozone port. If you fail to do
this, the water in your humidifier will be pushed out through
the Adapter Ozone Port and an overflow will result.
TRAVELING WITH
YOUR SLEEP EQUIPMENT:
It is not necessary to replace your
SoClean Adapter with the original lid.
RECONNECTING
THE ORIGINAL LID:
Remove the Ozone
Tube that is connected
to the stem of the
SoClean Adapter by
firmly pulling it o.
1SoClean
Adapter
Hinge Pin
Ozone
Tube
Remove the reservoir
from the sleep
equipment machine.
2
Remove the SoClean
Adapter from the
reservoir base by
opening the SoClean
Adapter fully, pushing
one side of the hinge
tab outward, and
freeing the SoClean
Adapter from the base.
3
Install the Original
Lid and Gasket to
the reservoir base by
inserting the hinge
pins into the notches
on the reservoir base.
If needed, insert one
hinge pin at a time and
gently flex the lid to
snap it in place.
4
Original Lid
NOTE: SoClean is not responsible for damage to your
sleep equipment machine or personal property resulting
from equipment mishandling.
Close the Original Lid and install the reservoir
back into your sleep equipment device.
5
Hose/Mask
Reservoir
SoClean 3 Connected to ResMed Airsense 10
SoClean
Adapter
SoClean 3
Ozone Tube
The below diagram shows a SoClean 3 connected.
The SoClean 2 setup will look similar but include the check valve.
Using Your SoClean Once you have completed the setup steps, you are
ready to begin the daily maintenance of your sleep
equipment accessories with your SoClean.
Safety Checklist Before
Using Your SoClean
Sleep equipment accessories are
washed in sink before first use
SoClean Adapter is installed on sleep
equipment machine
Ozone tube is connected to sleep
equipment machine
Sleep equipment hose is still connected
to sleep equipment machine and mask
SoClean is powered on
Filter is installed
SoClean, Inc.
12 Vose Farm Road | Peterborough, NH 03458 USA
A001484-11_Rev B C001485 Rev B
Issue Date: 08/2022
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

SoClean PNA1210-G23 Cleaning Adapter Operating instructions

Type
Operating instructions

SoClean PNA1210-G23 Cleaning Adapter is designed to work with ResMed AirSense 10 CPAP machines to provide daily automated cleaning and disinfection of your CPAP equipment.

Key Capabilities:

  • Connects to the water chamber of your ResMed AirSense 10 machine, replacing the original lid.
  • Uses activated oxygen (ozone) to kill up to 99.9% of bacteria, viruses, mold, and allergens from your CPAP mask, tubing, and water chamber.
  • Eliminates the need for manual cleaning and soaking, saving you time and effort.
  • Helps maintain optimal performance of your CPAP equipment, ensuring a cleaner and more effective therapy experience.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI