InSinkErator F-HC2200C User manual

Instant Hot Water Dispenser

Owner’s Manual

Series 2200

Series 1100

SST-FLTR

Installation, Care & Use

Instalacion, cuidado & uso

Installation, soin et utilisation

Equipment You May Need:

We are delighted that you have chosen the InSinkErator

®

Instant Hot Water Dispenser

to be a part of your home. This unique appliance will save you time and effort in the

kitchen, and you’ll enjoy discovering new uses for it each day. That’s exactly why

millions of people are now using an InSinkErator Instant Hot Water Dispenser.

We are confident that by following our step-by-step instructions, you’ll soon be enjoying

the convenience of instant hot water.

 For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing

or using this instant hot water dispenser.

 This particular unit is not intended for commercial use.

 Make sure that all electrical wiring and connections conform to local codes.

 A standard 120-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.

 The wall outlet powering your dispenser must have power supplied to it continuously.

 This outlet must be fused and should not be controlled by the same wall switch that operates the

disposer, unless you have a SinkTop Switch

™

from InSinkErator

®

.

 It is recommended that a dedicated control valve be installed on the cold water line supplying water

to this system.

 If you suspect elevated levels of chlorine in your water, it is recommended to use our water

filtration system.

 The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).

If it does, this will prevent your unit from operating properly.

 Moving parts inside the tank causing a rattling noise is normal.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

Equipment Required:

 Drill

 T-fitting

 Dedicated control valve

 Adjustable wrench

 Phillips and flat blade screwdrivers

 Pencil

 Tape measure

 Level

 Anchors for drywall

 Hole saw

 Basin wrench

 Hole punch

If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a

1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line.

See Step 1-B.

If you need to cut a mounting hole in your stainless steel sink, you may need a 1

1

⁄4" - 1

1

⁄2" hole saw made

for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other

than stainless steel.

WHAT YOU NEED TO GET STARTED

2

HOW TO USE THIS INSTRUCTION MANUAL

Provides a step-by-step narrative describing the installation step, with check boxes

that can be marked as you progress through the installation.

Contains simple illustrations that provide visual instruction to support the narrative.

CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.

These instructions are separated into main sections, indicated by numbers, and subsections,

indicated by capital letters. The manual is setup this way to allow you to take a break at any

point after completing a section or subsection without affecting the installation process.

What you’ll see in the

instruction manual:

1

2

3

Identify the model of your instant hot water dispenser and record it here:________________

A

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

INSTALLING THE FAUCET

Unpack dispenser components.

On a firm, flat surface, carefully

straighten the copper tubing.

1

2

An imminently hazardous situation, which, if not avoided, will result in death or serious injury.

A potentially hazardous situation, which, if not avoided, could result in death or serious injury.

A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

3

F-HC1100 F-GN1100

F-GN2215F-HC2215

F-GN2200

F-HC2200

OVERVIEW OF A

COMPLETED SETUP

3

COMPONENTS IN THIS PACKAGE

SST-FLTR

Filter Head

3/8" Tubes (2)

Filter

Discharge Tube

Filter Cartridge

3/4" Screws (4)

Brass Nut / Ferrule /

Tube Insert

F-HC1100 F-GN1100

F-HC2215 F-GN2215

F-HC2200 F-GN2200

Semi-circular

Mounting Plate

Rubber O-Ring Hex Nut

Hex Tool

Quick Connector

Plug (1)

Snap-Connect

Fitting (3 pieces)

4

5

The wall outlet for your dispenser must have power supplied to it continuously

and must be fused. It should not be controlled by the same wall switch

that operates your disposer, unless using an InSinkErator SinkTop Switch

TM

.

PREPARATION

START HERE

PROPER INSTALLATION SHOULD TAKE ABOUT 2-4 HOURS



Identify locations for the dispenser

faucet, tank and filter.

 Check to make sure there is proper

clearance for dispenser handles to

be fully opened.

 Check to make sure counter is 3"

thick or less.

 Make sure there is a grounded

electrical outlet under the sink.

 Turn off water supply.

 If using the sink sprayer hose hole,

remove nut that connects sprayer

hose at bottom of faucet.

 Using adjustable wrench, remove nut

connecting sprayer washer flange in

sprayer hole.

 Plug hose opening with either a 1/8"

plug or a 1/4" cap (not supplied).

1

A

B

If you have to drill through sink or

countertop, you may need to rent or purchase

the appropriate tools.

Consult a professional before drilling into

a surface other than stainless steel.

C

What if you don’t have a sprayer hole or

don’t want to use it?

 Many homeowners replace the soap

dispenser in their sink with an instant

hot water dispenser.

 If drilling a hole into a stainless steel

sink or counter top, you can cut a

mounting hole for the dispenser with a

hole saw for stainless steel, or you can

use a hole punch.

Required Hole Size

Hot & Cool Models 1

3

⁄8" - 1

1

⁄2"

Hot Only Models 1

1

⁄4" - 1

1

⁄2"

F-HC2215................3

1

⁄8"

F-GN2215................3

7

⁄8"

F-HC2200................3

1

⁄8"

F-GN2200................3

7

⁄8"

F-HC1100................3

1

⁄8"

F-GN1100................3

7

⁄8"

Required minimum from

center of hole to wall

Maximum counter

thickness is 3".

If installing ONLY new faucet or new tank, see Page 10.

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

 From under the sink, place the

semi-circular mounting plate onto

the threaded stud.

 Place hex nut onto the threaded stud.

Ensure faucet head is at desired angle.

 Insert screwdriver into hole on side of

hex tool (creating a “T”), and use tool

to tighten nut and secure faucet.

2

Semi-circular mounting plate should

encircle all descending tubes and

extend beyond sink hole when tight.

 Ensure that the black O-ring is

properly seated in the base of the

dispenser head (the groove on the

underside of the dispenser).

 Feed tubes down through the hole

in the sink or countertop until the

base is at rest on the sink or

countertop surface.

 Unpack dispenser components.

 On a firm, flat surface, carefully

straighten the copper tubing.

An assistant may be needed to hold

the dispenser head in place

while securing the dispenser.

B

A

C

D

Make sure to use rubber O-ring

to ensure proper seal.

INSTALLING THE FAUCET

6

7

A

 Select a spot under the sink to mount

tank vertically within reach of both

plumbing and electrical connections.

The tank should be within 16" or less

of faucet water lines and within 30"

or less of a standard grounded outlet.

 While holding tank in place on

the spot selected for installation,

use a pencil to mark locations for

2 hanging screws.

Property Damage: Tank must be located within 16" of

faucet and within 30" or less of a standard grounded

outlet. DO NOT extend plumbing or electrical lines.

3

Tank must be

mounted level

to ensure

proper operation.

Mount tank vertically in an area that

allows clearance on the underside of the

tank for drainage, if necessary.

DO NOT over tighten screws.

 Pre-drill 1/8" pilot holes at marks.

 Turn screws into pre-drilled holes,

leaving 1/4" exposed.

 Hang the tank on the screws.

 Tighten the screws with only

1/2 turn clockwise.

B

Screws provided are for use in wood

studs or cabinets only. Use wall anchors

(not supplied) for installation into drywall.

Leave 1/4" for

hanging tank.

Tank A

 Without depressing the gray button,

place the snap-connect fitting at

the end of the blue or copper 1/4"

tube onto the left fitting on the tank,

pushing until it clicks into place. (1)

Tank B

 Insert blue 1/4" tube into quick-

connect fitting at left. (1)

Both Tanks

 Slip the flexible white 7/16" tube

over barbed steel fitting and slide

down approximately 1/2". (2)

 Slip the clear 5/16" tube over the

smooth plastic fitting and slide down

approximately 1/2". (3)

 Check for pinched or crimped tubes.

4

A

Property Damage: Pinched or blocked water lines

may cause damage to the dispenser tank.

Hose clamps are not needed for any

of the connections.

Property Damage: Check to make sure

tubes are connected properly and are

pushed down as far as possible.

(1) (2) (3)

(1) (3) (2)

Tank A

Tank B

MOUNTING THE TANK

CONNECTING FAUCET TO TANK

Property Damage: Do not extend the copper

lines farther than the 16" provided.

Personal Injury: Do not locate filter above an outlet or other

electrical device. Install head and bracket so that connec-

tions require no stretching, kinking or pinching of tubing.

It is normal for approximately 2 oz. of water to

discharge when filter is removed.

Property Damage: Tube runs need to form to the cabinet’s

contours to allow storage space with no sharp bends. Tubes

need clean, perpendicular, burr-free cuts to ensure a true fit.

A

Determine length of tubing required,

then cut to length making sure the cut

is perpendicular and burr-free.

Insert a white 3/8" tube into inlet side

of filter head until it stops.

Press in again to ensure a secure fit.

Insert the other white 3/8" tube

into outlet side of filter head

until it stops. Press in again to

ensure a secure fit.

Mark hole locations for filter head

and bracket in a spot that allows

for filter replacement.

Drill 1/8" starter holes and attach racket to

wall with wood screws, turning until snug.

Remove red filter cap, insert filter

cartridge into filter head and twist

clockwise until “LOCK” arrow on the

filter aligns with arrow on bracket.

To redirect filter replacement water

discharge, place 6" clear tube over

vent hole on the left side of filter head.

Note: 3/8" fitting is required to make

connection to water supply.

Connect remaining white 3/8" tube to

incoming water supply line.

(See Step 6.)

C

Insert the copper tube(s) from the

dispenser into the 3/8" to 1/4"

quick-connect fitting.

Connect the white 3/8" tube

from the right outlet on the filter

head into the quick-connect fitting until

it stops. Press in again to ensure a

secure fit.

from water

supply line to dispenser

To remove tube(s) or plug from quick-connector,

depress the release ring and gently pull away.

Discharge tube

From water

supply line

To dispenser

From filter or

water supply line

From filter or

water supply line

D

Plug

5

INSTALLING FILTRATION SYSTEM

Hot & cool models

Hot only models

8

Screws provided are for use in wood

studs or cabinets only. Use wall anchors

(not supplied) for installation into drywall.

B

9

Scalding Hazard: The faucet dispenses near-boiling

(212ºF) water which can instantly cause scalds or

burns. Use care when operating this appliance.

Property Damage: Join remaining tube

to cold water supply only.

C

 Turn on the cold water supply.

 Depress the dispenser’s HOT handle

and hold it until water flows from the

spout (approximately 1 to 2 minutes).

 Run the water for at least 2 minutes

to flush lines (both the hot and cold

handles independently if applicable).

B

A



Check all connections to ensure they are

tight

and that there are no leaks.



Plug in instant hot water tank.

Water will be cold at first.

Allow 12-15 minutes for water to reach

target temperature.

Gurgling or hissing is normal during the

initial heating cycle.

6

Brass Nut

Ferrule

Brass Insert

Plastic

tube



Install a T-fitting (not included)

onto the cold water supply line.



Install dedicated water control valve

with 3/8" compression fitting.



At the end of the white 3/8" tube from the

filter or quick-connector, slide the supplied

brass nut and ferrule over the tube and

then push in the brass tube insert.



Insert the white 3/8" tube into the 3/8"

compression fitting and tighten.

Property Damage: A standard grounded outlet within

30" of the dispenser is required under the sink. Do

not use an extension cord set with the dispenser.

If the water coming from the faucet is not hot 15 minutes after the unit

has been plugged in – or for other issues related to the operation of your

instant hot water dispenser – refer to the “Troubleshooting” section on Page 14.

FINAL WATER CONNECTION

10

B



At tank top, depress release ring or gray

release tab into quick-connect fitting

securing blue or copper 1/4" tube and

gently pull line off tank fitting. Pull white

7/16" tube and clear 5/16" tube off fittings.



If not already equipped, the included

snap-connect fitting must be installed.



To install snap-connect fitting, unscrew

brass mounting nut and remove snap-

connect fitting, brass ferrule and nut.

A

 Slide brass nut and plastic ferrule

onto the 1/4" blue or copper tube

running from the faucet.

 Insert blue or copper tube into snap-

connect fitting and tighten brass nut

with a wrench, 1 to 2 turns clockwise.

 You may elect to use existing tank

mounting bracket.

 Refer to Page 7, Steps 3-4 for

complete installation instructions.

A

 Determine if your existing tank is A, gray

plastic shell, or B, white metal shell.

 At tank top, depress gray release tab

(if A) or release ring (if B) into quick-

connect fitting securing blue or

copper 1/4" tube and gently pull line

out of ﬁtting. Pull white 7/16" tube

and clear 5/16" tube off fittings.

 Remove existing faucet.

Blue Tube

Property Damage:

Do not over tighten brass nut.

Property Damage:

Turn off water & unplug tank.

Property Damage:

Unplug tank before connecting faucet.

Tank A

 The snap-connect fitting will be

attached directly to the tank.

Tank B

 Cut off snap-connect fitting at the

end of the blue 1/4" tube. Ensure

that cut is straight and burr free.

 Insert blue tube into fitting on tank.

 Skip to Step 2 (pages 7-11) for

complete installation instructions.

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

IF INSTALLING ONLY NEW TANK

B

Release

Tab

1/4"

blue

7/16"

white

5/16"

clear

Release

Ring

1/4"

blue or

copper

7/16"

white

5/16"

clear

Cut

here

Check

orientation

of ferrule

Make note of

orientation

of ferrule

IF INSTALLING ONLY NEW FAUCET

Tank A

Tank B

Electric Shock Hazard: Using an ungrounded or improperly connected

appliance can result in serious injury or death from electrical shock.

Property Damage: To avoid water damage, replace any loose or split tubing.

Periodically inspect the unit for any signs of leakage and immediately remove from

service any unit suspected of leaking.

Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system.

DO NOT close vent tube or connect other type dispensers or valves to the tank. Use only

the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an

authorized InSinkErator Service agent for repairs or replacement components.

Dispenser: 5-year warranty

Stainless Steel Tank: 3-year warranty

Filtration System: 1-year warranty (excluding replaceable filter cartridge)

Covers all replacement parts and labor to correct defects in material or workmanship in the

dispenser system, excluding the replaceable filter cartridge, for the full warranty period from

the date of installation in your home. If warranty service is required during the warranty period,

contact an authorized InSinkErator service agent to replace or repair the unit in your home at

no cost to you. If your dispenser is replaced rather than repaired, the warranty on the new unit

shall be for the duration of the remaining portion of the original dispenser’s warranty. Note:

Warranty is determined by unit serial number and/or date of installation. Purchase or

installation receipt may be required to verify warranty status. When service is required, and for

the location of your nearest factory authorized service center, call toll free 1-800-558-5700.

The foregoing warranty does not apply to damage or inoperation resulting from accident,

alteration, misuse, abuse, improper installation, installation not in accordance with these

instructions or local electrical and/or plumbing codes. We do not assume any responsibility for

consequential damage. Install using genuine InSinkErator

®

manufactured components only.

Use of non InSinkErator components will void your warranty.

Some states do not allow limitations on how long an implied warranty lasts, or the

exclusion or limitations of incidental or consequential damages, so the above limitations or

exclusion may not apply to you. This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This appliance must be grounded. This instant hot water dispenser is equipped with a cord that

has a grounding conductor and a grounding pin. The plug must be connected to an appropriate

outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet

installed by a qualified electrician. Check with a qualified electrician or serviceman if you are in

doubt as to whether the instant hot water dispenser is properly grounded.

WARRANTY INFORMATION

Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as

rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

An instant hot water dispenser, like any water heater, has a limited life and will eventually

fail. To avoid possible property damage, this instant hot water dispenser should be

regularly examined for leakage and replaced when necessary. A drain pan, plumbed to

an appropriate drain or outfitted with a leak detector, should be used in those

applications where any leakage could cause property damage.

11

Electric Shock Hazard: To prevent electrical shock, disconnect power before

servicing unit. Use only a properly grounded and polarized electric outlet.

CARE AND USE

Scalding Hazard: Do not allow

water to boil. May result in

severe burns.

Factory temperature pre-set is

200˚F. To reset the thermostat

to 200°, turn the indicator two

notches to the right of vertical.

 Adjust the thermostat

slowly, turning the dial

clockwise to increase

temperature or counter clockwise to decrease

temperature, then activate faucet handle for

20 seconds to bring in fresh water to be

heated at the new setting. Allow 5-7 minutes

for water to reach new temperature.

ADJUSTING THE THERMOSTAT



Only use mild cleaners to clean the faucet

and plastic components.



Cleaners with acids, abrasives, alkaline or

organic solvents will result in deterioration of

the plastic components and void the warranty.

CLEANING THE FAUCET AND TANK

Replace filter cartridge when there is an obvious

decrease in water flow to the faucet or if there is an

objectionable taste or odor to the water.

When the inlet and outlet ports have been closed

and the filter’s internal pressure has been relieved,

water (about 2 oz) will discharge from vent line.

If the new filter cartridge cannot be inserted,

insert the old one and turn until it stops, remove it

and then retry the new cartridge.

Carbon filters should be replaced within 12 months.

FILTER GUIDE AND REPLACEMENT

Filter replacement instructions:

Replace with an InSinkErator

®

filter.

Place pan or dish towel under the filter to

catch water drainage during change.

Slowly turn the cartridge counter-clockwise

completely until it stops (1/4 turn).

Pull cartridge straight down and discard.

Insert new cartridge into filter head.

Top surface of cartridge will become flush

with the bottom of the filter head when

fully engaged.

Turn the cartridge clockwise until it stops

(1/4 turn).

Align the in/out arrow on the head and

bracket assembly to the in/out arrow on

the cartridge.

Open faucet to expel trapped air.

Run water for 3 minutes before usage.



Regularly inspect the unit for any signs of

leakage. If there are signs of water damage,

immediately remove the unit from service.



To avoid water damage from leakage,

replace all cut, loose or split tubing.



A drain pan, plumbed to an appropriate

drain or outfitted with a leak detector,

should be used in those applications where

any leakage could cause property damage.

PROPERTY DAMAGE

Anytime the instant hot water dispenser is not

used for extended periods of time, unplug and

drain unit. If it is below freezing you will need

to unplug the unit and drain it.



Disconnect power from unit.



Push hot water dispenser faucet lever

and allow water to flow until it is cool.



Shut the cold water supply off at the valve.



Locate and remove drain screw from

bottom center of water tank and drain

the water into empty pail.



Empty the tank and then reinstall drain

screw into the bottom of tank, turning

until snug. Do NOT over tighten.



Remove and discard filter cartridge.



To put back into working order, install

new filter cartridge, fill tank with water

and reconnect the electrical cord. (Refer

to Page 9, Step 6B)

SEASONAL STORAGE/DRAINAGE

12

approx. 200°

FILTRATION INFORMATION

To reduce the risk associated with ingestion of contaminates due to use with water that is

microbiologically unsafe or of unknown quality, do not use with water that is microbiologically

unsafe or of unknown quality without adequate disinfection before or after the system.

To reduce the risk associated with property damage due to water leakage:

• Protect filter from freezing. Drain filter when temperatures drop below 40°F (4.4°C).

• Do not install if water pressure exceeds 120 psi (828 kPa). If your water pressure

exceeds 120 psi, you must install a pressure limiting valve. Contact a plumbing

professional if you are uncertain how to check your water pressure.

• Do not install where water hammer conditions may occur. If water hammer

conditions exist you must install a water hammer arrester. Contact a plumbing

professional if you are uncertain how to check for this condition.

• Do not install on hot water supply lines. The maximum operating water temperature

of this filter system is 100°F (38°C).

• The disposable filter cartridge must be replaced every twelve months or at the

specified service cycle.

• Read and follow instructions before installation and use of this system.

The InSinkErator

®

Instant Hot Water Dispenser Filtration System is intended for use in filtering

sediment, chlorine taste and odor from drinking water, and has not been evaluated for other

uses. The system is typically installed (near or beneath a sink) where filtered drinking water is

desired, and must be installed, operated and maintained as specified in the installation and

use instructions.

13

TROUBLESHOOTING

WHAT TO DO

Water and steam spits

forcefully from spout

without turning on the

dispenser faucet.

Water is not hot.

• Unit is boiling.

May be normal during initial setup.

• The unit is unplugged.

• The electric outlet is inoperative.

• Activate faucet lever to release some water from

the tank.

• Adjust water temperature using dial on tank front.

Remember that at higher altitudes, water boils

at lower temperatures.

• Make sure the unit is connected to a properly grounded

electric outlet.

• Make sure the circuit breaker or fuses are

functioning properly.

• Check that the outlet is not switched off.

Water is too hot

or not hot enough.

• Thermostat is not adjusted to

your needs.

•

Adjust the thermostat slowly, then activate faucet lever for 20

seconds to bring in fresh water to be heated at the new setting.

Allow 5-7 minutes for water to reach new temperature.

Water comes out the

vent instead of spout.

• Outlet tube is blocked. • Check that outlet tube is not kinked, twisted or pinched.

• Unscrew spout end piece and clean out any debris.

Water is dripping from

the spout/vent

intermittently.

• The expansion chamber isn’t draining

properly due to low water pressure.

• The spout is blocked.

• Unplug the unit. If the dripping doesn’t stop after a few

minutes, check the supply valve to ensure that is fully

open and there are no obstructions in the water line

reducing the pressure below 30 psi (

i.e., a poorly mounted

saddle valve, a clogged water filter, or a partially opened

shut-off valve).

• Unscrew spout end piece and clean out any debris.

Water is dripping

from the spout/vent

constantly.

• Debris in the water line may be

in the faucet valve seat causing a

slow water leak.

• Unscrew spout end piece and clean out any debris.

• Activate faucet lever 7-10 times to flush faucet & lines.

Divided stream.

• Debris in the end piece. • Unscrew spout end piece and clean out any debris.

PROBLEM POSSIBLE CAUSE

FILTRATION ISSUES

If you are still experiencing trouble call the AnswerLine

™

1-800-558-5700.

Water taste or odor

New filter leaks or

doesn’t fit

No water flow or

low water flow

• Filter needs to be flushed out

• Life of filter has expired

• Head and bracket not fully rotated

• Filter O-ring breach

• Life of filter has expired

• Activate the faucet lever and run until the water is cold.

If there is no change, replace filter cartridge.

• Remove, inspect, reinstall filter cartridge.

• Remove new filter, replace with old filter. Check operation.

If OK, reinstall new filter and recheck operation.

• Replace filter cartridge. See page 12.

Please read Troubleshooting Guide and/or visit

www.insinkerator.com before calling AnswerLine

™

14

Page is loading ...

The Emerson logo is a trademark and

service mark of Emerson Electric Co.

1.800.558.5700

www.insinkerator.com

InSinkErator may make improvements and/or

changes in the specifications at any time, in its sole

discretion, without notice or obligation and further

reserves the right to change or discontinue models.

InSinkErator F-HC2200C User manual

InSinkErator F-HC2200C User manual

in other languages

Related papers

Other documents