Hotpoint FH 1039 0 XA/HA Owner's manual

Category
Ovens
Type
Owner's manual

This manual is also suitable for

FH 1039 0 XA/HA
English
Operating Instructions
OVEN
Français
Mode d’emploi
FOUR
Español
Manual de instrucciones
HORNO
Italiano
Istruzioni per l’uso
FORNO
Portuges
Instruções para a utilização
FORNO
Sommario
Istruzioni per l’uso,1
Avvertenze,2
Assistenza,5
Descrizione dell’apparecchio,7
Descrizione dell’apparecchio,8
Installazione,10
Avvio e utilizzo,12
Programmi,13
Precauzioni e consigli,17
Manutenzione e cura,18
Anomalie e rimedi,19
Contents
Operating Instructions,1
Warnings,2
Assistance,5
Description of the appliance,7
Description of the appliance,8
Installation,20
Start-up and use,22
Modes,23
Precautions and tips,27
Maintenance and care,28
Troubleshooting,29
Sommaire
Mode d’emploi,1
Avertissements,3
Assistance,5
Description de l’appareil,7
Description de l’appareil,8
Installation,30
Mise en marche et utilisation,32
Programmes,33
Précautions et conseils,37
Nettoyage et entretien,38
Anomalies et remèdes,39
Sumario
Manual de instrucciones,1
Advertencias,3
Asistencia,6
Descripción del aparato,7
Descripción del aparato,9
Instalación,40
Puesta en funcionamiento y uso,42
Programas,43
Precauciones y consejos,47
Mantenimiento y cuidados,48
Anomalías y soluciones,49
Índice
Instruções para a utilização,1
Advertências,4
Assistência,6
Descrição do aparelho,7
Descrição do aparelho,9
Instalação,50
Início e utilização,52
Programas,53
Precauções e conselhos,57
Manutenção e cuidados,58
Anomalias e soluções,59
2
Avvertenze
ATTENZIONE: Questo apparecchio e le sue parti
accessibili diventano molto caldi durante l’uso.
Bisogna fare attenzione ed evitare di toccare gli
elementi riscaldanti. Tenere lontani i bambini inferiori
agli 8 anni se non continuamente sorvegliati. Il
presente apparecchio può essere utilizzato dai
bambini a partire dagli 8 anni e da persone con
ridotte capacità siche, sensoriali o mentali oppure
con mancanza di esperienza e di conoscenza se
si trovano sotto adeguata sorveglianza oppure se
sono stati istruiti circa l’uso dell’apparecchio in modo
sicuro e se si rendono conto dei pericoli correlati. I
bambini non devono giocare con l’apparecchio. Le
operazioni di pulizia e di manutenzione non devono
essere effettuate dai bambini senza sorveglianza.
Non utilizzare prodotti abrasivi né spatole di
metallo taglienti per pulire lo sportello in vetro del
forno in quanto potrebbero grafare la supercie,
provocando, così, la frantumazione del vetro.
Non utilizzare mai pulitori a vapore o ad alta pressione
per la pulizia dell’apparecchio.
ATTENZIONE: Assicurarsi che l’apparecchio sia
spento prima di sostituire la lampada per evitare la
possibilità di scosse elettriche.
! Quando si inserisce la griglia assicurarsi che il
fermo sia rivolto verso l’alto e nella parte posteriore
della cavità.
Warnings
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children less than 8
years of age shall be kept away unless continuously
supervised. This appliance can be used by children
aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been
given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made
by children without supervision.
Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Never use steam cleaners or pressure cleaners on
the appliance.
WARNING: Ensure that the appliance is switched
off before replacing the lamp to avoid the possibility
of electric shock.
! When you place the rack inside, make sure that the
stop is directed upwards and in the back of the cavity.
5
Assistenza
Attenzione:
L’apparecchio è dotato di un sistema di diagnostica automatica che consente
di rilevare eventuali malfunzionamenti. Questi vengono comunicati dal display
tramite messaggi del tipo: “F--” seguito da numeri.
In questi casi è necessario l’intervento dell’assistenza tecnica.
Prima di contattare l’Assistenza:
Vericare se l’anomalia può essere risolta autonomamente;
Riavviare il programma per controllare se l’inconveniente è stato ovviato;
In caso negativo, contattare il Servizio Assistenza Tecnico Autorizzato.
! Non ricorrere mai a tecnici non autorizzati.
Comunicare:
Il tipo di anomalia;
il messaggio visibile sul display TEMPERATURA
Il modello della macchina (Mod.)
Il numero di serie (S/N)
Queste ultime informazioni si trovano sulla targhetta caratteristiche posta
sull’apparecchio
Assistenza Attiva 7 giorni su 7
Se nasce il bisogno di assistenza o manutenzione basta chiamare il Numero
Unico Nazionale 199.199.199* per essere messi subito in contatto con il Centro
Assistenza Tecnica più vicino al luogo da cui si chiama.
È attivo 7 giorni su 7, sabato e domenica compresi, e non lascia mai inascoltata
una richiesta.
Estensione di garanzia Airbag
Airbag è il servizio esclusivo creato da Ariston che integra e prolunga nel
tempo i contenuti della garanzia standard: con una modica cifra protegge
il cliente da ogni imprevisto riguardante l’assistenza e la manutenzione
dell’elettrodomestico. Per i 5 anni successivi alla data di acquisto il cliente
che aderisce al programma Airbag avrà diritto gratuitamente a:
l’intervento entro 48 ore dalla chiamata;
il contributo per spese di trasferta del Tecnico (diritto di chiamata);
la manodopera;
le parti di ricambio originali;
il trasporto dell’elettrodomestico non riparabile in loco.
Inoltre, qualora l’elettrodomestico non sia riparabile la garanzia prevede
la sostituzione a prezzo agevolato in funzione dell’anzianità del prodotto.
* Al costo di 14,25 centesimi di Euro al minuto (iva inclusa) dal Lun. al Ven.
dalle 08:00 alle 18:30, il Sab. dalle 08:00 alle 13:00 e di 5,58 centesimi di
Euro al minuto (iva inclusa) dal Lun. al Ven. dalle 18:30 alle 08:00, il Sab. dalle
13:00 alle 08:00 e i giorni festivi, per chi chiama dal telefono sso.
Per chi chiama da radiomobile le tariffe sono legate al piano tariffario
dell’operatore telefonico utilizzato.
Le suddette tariffe potrebbero essere soggette a variazione da parte
dell’operatore telefonico; per maggiori informazioni consultare il sito www.
indesit.com.
Assistance
Warning:
The appliance is tted with an automatic diagnostic system which detects any
malfunctions. Malfunctions are signalled through messages of the following
type: “F—” followed by numbers.
Call for technical assistance in the event of a malfunction.
Before calling for Assistance:
Check whether you can x the problem yourself.
Restart the programme to check whether the malfunction has
disappeared.
If it has not, contact the Authorised Technical Assistance Service.
! Never use the services of an unauthorised technician.
Please have the following information to hand:
The type of problem encountered.
The message shown on the TEMPERATURE display.
The appliance model (Mod.).
The serial number (S/N).
The latter two pieces of information can be found on the data plate located
on the appliance.
Assistance
Attention :
L’appareil dispose d’un système d’autotest qui permet de détecter toute
anomalie de fonctionnement. Ces anomalies sont afchées sous la forme:
«F—» suivi de chiffres.
Contacter alors un service d’assistance technique.
Avant d’appeler le service de dépannage :
Vérier s’il est possible de résoudre le problème soi-même ;
Redémarrer le programme pour contrôler si le problème a été résolu;
Si ce n’est pas le cas, contacter le service d’Assistance technique agréé.
! Ne jamais faire appel à des techniciens non agréés.
Indiquer :
le type d’anomalie;
le code erreur afché sur l’écran TEMPERATURE
le modèle de l’appareil (Mod.);
son numéro de série (S/N).
Ces informations gurent sur la plaque signalétique apposée sur l’appareil
7
Descrizione dell’apparecchio
Vista d’insieme
1 POSIZIONE 1
2 POSIZIONE 2
3 POSIZIONE 3
4 POSIZIONE 4
5 POSIZIONE 5
6 GUIDE di scorrimento dei ripiani
7 Ripiano LECCARDA
8 Ripiano GRIGLIA
9 Pannello di controllo
Description of the appliance
Overall view
1 POSITION 1
2 POSITION 2
3 POSITION 3
4 POSITION 4
5 POSITION 5
6 GUIDES for the sliding racks
7 DRIPPING PAN
8 GRILL
9 Control panel
Description de l’appareil
Vue d’ensemble
1 NIVEAU 1
2 NIVEAU 2
3 NIVEAU 3
4 NIVEAU 4
5 NIVEAU 5
6 GLISSIERES de coulissement
7 Support LECHEFRITE
8 Support GRILLE
9 Tableau de bord
Descripción del aparato
Vista en conjunto
1 POSICIÓN 1
2 POSICIÓN 2
3 POSICIÓN 3
4 POSICIÓN 4
5 POSICIÓN 5
6 GUÍAS de deslizamiento de las bandejas
7 Bandeja GRASERA
8 Bandeja PARRILLA
9 Panel de control
Descrição do aparelho
Vista de conjunto
1 POSIÇÃO 1
2 POSIÇÃO 2
3 POSIÇÃO 3
4 POSIÇÃO 4
5 POSIÇÃO 5
6 GUIAS de escorrimento das prateleiras
7 Prateleira BANDEJA PINGADEIRA
8 Prateleira GRADE
9 Painel de comandos
7
8
9 6
1
2
3
4
5
8
Descrizione dell’apparecchio
Pannello di controllo
1 Icone PROGRAMMI MANUALI
2 Display TEMPERATURA
3 Icona TEMPERATURA
4 Icona DURATA
5 Display TEMPI
6 Icona FINE COTTURA
7 Icona BLOCCO COMANDI
8 AVVIO/ARRESTO
9 Icona LUCE
10 Icona OROLOGIO
11 Icona CONTAMINUTI
12 Icone REGOLAZIONE TEMPI/TEMPERATURA
13 Icone PRERISCALDAMENTO/CALORE RESIDUO
14 Icone PROGRAMMI AUTOMATICI/ECO
15 ACCENSIONE PANNELLO
Description of the appliance
Control panel
1 MANUAL COOKING MODE Icons
2 TEMPERATURE display
3 TEMPERATURE icon
4 DURATION icon
5 TIME display
6 END OF COOKING Icon
7 CONTROL PANEL LOCK icon
8 START / STOP
9 LIGHT icon
10 CLOCK icon
11 MINUTE MINDER Icon
12 TIME / TEMPERATURE ADJUSTMENT Icons
13 PREHEATING / RESIDUAL HEAT icons
14 AUTOMATIC/ECO COOKING MODE icons
15 CONTROL PANEL POWER BUTTON
Description de l’appareil
Tableau de bord
1 Icônes PROGRAMMES MANUELS
2 Afcheur TEMPERATURE
3 Icône TEMPÉRATURE
4 Icône DURÉE
5 Afcheur TEMPS
6 Icône FIN CUISSON
7 Icône VERROUILLAGE COMMANDES
8 DÉPART / ARRÊT
9 Icône ECLAIRAGE
10 Icône HORLOGE
11 Icône MINUTEUR
12 Icônes RÉGLAGE TEMPS / TEMPÉRATURE
13 Icône PRÉCHAUFFAGE / CHALEUR RÉSIDUELLE
14 Icônes PROGRAMMES AUTOMATIQUES / ECO
15 ALLUMAGE PANNEAU
10
11
12
13
14
1
2
43
7
6
5
8
9
15
20
GB
Installation
! Please keep this instruction booklet in a safe place for future reference. If
the appliance is sold, given away or moved, please make sure the booklet is
also passed on to the new owners so that they may benet from the advice
contained within it.
! Please read this instruction manual carefully: it contains important information
concerning the safe operation, installation and maintenance of the appliance.
Positioning
! Do not let children play with the packaging material; it should be disposed
of in accordance with local separated waste collection standards (see
Precautions and tips).
! The appliance must be installed by a qualied professional in accordance
with the instructions provided. Incorrect installation may damage property or
cause harm to people or animals.
Built-in appliances
Use an appropriate cabinet to ensure that the appliance operates properly:
The panels adjacent to the oven must be made of heat-resistant material.
Cabinets with a veneer exterior must be assembled with glues which can
withstand temperatures of up to 100°C.
To install the oven under the counter (see diagram) or in a kitchen unit,
the cabinet must have the following dimensions:
595 mm.
595 mm.
25 mm.
545 mm.
5 mm.
567 mm.
23 mm.
575-585 mm.
45 mm.
560 mm.
547 mm. min.
! The appliance must not come into contact with electrical parts once it has
been installed. The indications for consumption given on the data plate have
been calculated for this type of installation.
Ventilation
To ensure adequate ventilation, the back panel of the cabinet must be
removed. It is advisable to install the oven so that it rests on two strips of
wood, or on a completely at surface with an opening of at least 45 x 560
mm (see diagrams).
560 mm.
45 mm.
Centring and xing
Secure the appliance to the cabinet by opening the oven door and putting 4
screws into the 4 holes on the outer frame.
! All parts which ensure the safe operation of the appliance must not be
removable without the aid of a tool.
Electrical connection
Ovens equipped with a three-pole power supply cable are designed to operate
with alternating current at the voltage and frequency indicated on the data
plate located on the appliance (see below).
Fitting the power supply cable
1. Open the terminal board by inserting
a screwdriver into the side tabs of the
cover. Use the screwdriver as a lever
by pushing it down to open the cover
(see diagram).
2. Install the power supply cable by
loosening the cable clamp screw and
the three wire contact screws
L-N- .
Connect the wires to the corresponding
terminals: the Blue wire to the terminal
marked (N), the Brown wire to the
terminal marked (L) and the Yellow/
Green wire to the terminal marked
(see diagram).
3. Secure the cable by fastening the
clamp screw.
4. Close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indicated on the data
plate (see table).
The appliance must be directly connected to the mains using an omnipolar
switch with a minimum contact opening of 3 mm installed between the
appliance and the mains. The switch must be suitable for the charge indicated
and must comply with current electrical regulations (the earthing wire must not
be interrupted by the switch). The supply cable must be positioned so that it
does not come into contact with temperatures higher than 50°C at any point
(the back panel of the oven, for example).
! The installer must ensure that the correct electrical connection has been
performed and that it is fully compliant with safety regulations.
L
N
N
L
GB
21
Before connecting the appliance to the power supply, make sure that
The appliance is earthed and the plug is compliant with the law.
The socket can withstand the maximum power of the appliance, which is
indicated on the data plate.
The voltage is in the range between the values indicated on the data plate.
The socket is compatible with the plug of the appliance. If the socket is
incompatible with the plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable and the
electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised technicians
only (see Assistance).
! The manufacturer declines any liability should these safety measures
not be observed.
APPLIANCE SPECIFICATIONS
Dimensions*
width 43.5 cm
height 32,4 cm
depth 41.5 cm
Volume*
59 l
Dimensions**
width 45.5 cm
height 32,4 cm
depth 41.5 cm
Volume**
62 l
Electrical
connections
voltage: 220-240V~ 50/60 Hz or 50Hz
maximum power absorbed 2800 W
(see data plate)
* Only for models with drawn rails.
** Only for models with wire rails.
EU Directive no 65/2014
supplementing Directive 2010/30/EU.
EU Regulation no 66/2014
implementing Directive 2009/125/EC.
Standard EN 60350-1
Standard EN 50564
This appliance conforms to the
following European Economic
Community directives:
- 2006/95/EC of 12/12/06 (Low
Voltage) and subsequent
amendments;
- 2004/108/EC of 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments;
- 93/68/EEC of 22/07/93 and
subsequent amendments.
- 2002/96/EU and subsequent
amendments.
- 1275/2008 standby/off mode.
ENERGY LABEL
and
ECODESIGN
Declared energy consumption
for Forced convection Class –
heating mode: ECO.
22
GB
Start-up and use
WARNING! The oven is provided
with a stop system to extract the
racks and prevent them from coming
out of the oven (1).As shown in the
drawing, to extract them completely,
simply lift the racks, holding them on
the front part, and pull (2).
! The rst time you use your appliance, heat the empty oven with its door closed
at its maximum temperature for at least half an hour. Make sure that the room
is well ventilated before switching the oven off and opening the oven door. The
appliance may emit a slightly unpleasant odour caused by protective substances
used during the manufacturing process burning away.
! To make the setting process easier, press and hold the “ ” and “ ” buttons
to scroll through the numbers on the display rapidly.
! Each setting will automatically be stored in the appliance memory after 10
seconds.
! The touch controls cannot be activated if the user is wearing gloves.
! In order to optimise the cooking performance, when starting the selected
function, product settings will be applied that could cause a delayed start of
the fan and heating elements.
Control panel lock
! The control panel can be locked while the oven is off, once cooking has
started or nished and during programming.
To lock the oven controls, press and hold the button for at least 2
seconds. A buzzer will sound and the TEMPERATURE display shows the
key symbol “O—n”. The icon will light up to indicate lock activation.
To deactivate the lock, press and hold the button again for at least 2
seconds.
Setting the clock
! The clock can only be set when the oven is switched off. If the oven is in
standby mode, pressing the button once will display the current time
setting. Press it again to set the time.
After connection to the power supply network or after a blackout, the
button and the digits on the TIME display will ash for 10 seconds.
To set the clock:
1. Press the button.
2. Adjust the hour gure using the and buttons.
3. Once you have reached the correct hour value, press the button.
4. Repeat the above process to set the minutes.
If a blackout occurs, it will be necessary to reset the clock. If the icon
ashes on the display, this indicates that the clock has not been set correctly.
Setting the minute minder
! The minute minder may be set regardless of whether the oven is switched
on or off. It does not switch the oven on or off.
When the set time has elapsed, the timer emits a buzzer that will automatically
stop after 30 seconds or when any active button on the control panel is
pressed.
To adjust the timer proceed as follows:
1. Press button .
2. Set the desired time using buttons “ ” and “ ”.
3. Once you have reached the desired value, press the button again.
The lit symbol will remind you that the minute minder is on.
To cancel the minute minder, press the button and use the “ ” and “
” buttons to set the time to 00:00. Press button again.
The icon will switch off to indicate that the minute minder has been
disabled.
Starting the oven
1. Switch the control panel on by pressing the button. The appliance
buzzer sounds three times (ascending) and all buttons light up in sequence.
2. Press the button corresponding to the desired cooking mode. The
TEMPERATURE display shows:
- the temperature associated with the mode, if programming manually;
- “Auto”, if programming is automatic.
The TIME display shows:
- the current time, if programming manually;
- the duration, if programming is automatic.
3. Press the button to begin cooking.
4. The oven will begin its preheating phase, the preheating indicators will light
up as the temperature rises.
5. When the preheating process has nished, a buzzer sounds and all the
preheating indicator lights show that this stage has been completed: the food
can then be placed in the oven.
6. During cooking it is always possible to:
- change the temperature by pressing the button, followed by the “
and “ buttons (manual modes only);
- set the duration of a cooking mode (see Cooking Modes);
- press the button to stop cooking. In this case the appliance stores the
temperature modied previously in its memory (manual modes only);
- switch off the oven by pressing the button for 3 seconds.
7. If a blackout occurs while the oven is already in operation, an automatic
system within the appliance will reactivate the cooking mode from the point at
which it was interrupted, provided that the temperature has not dropped below
a certain level. Programmed cooking modes which have not yet started will
not be restored and must be reprogrammed (for example: a cooking mode
has been programmed to start at 20:30. At 19:30 a blackout occurs. When the
power supply is restored, the mode will have to be reprogrammed).
! There is no preheating stage for the GRILL mode.
! Never put objects directly on the bottom of the oven; this will prevent the
enamel coating from being damaged.
! Always place cookware on the rack(s) provided.
Cooling ventilation
In order to cool down the external temperature of the oven, a cooling fan
blows a stream of air between the control panel and the oven door, as well
as towards the bottom of the oven door.
At the beginning of the FAST CLEAN mode, the cooling fan operates at low
speed.
GB
23
! Once cooking has been completed, the cooling fan continues to operate
until the oven has cooled down sufciently.
Oven light
The light comes on when the oven door is opened or when a cooking mode
starts. The button can be used to switch on the light at any time.
Residual heat indicators
The appliance is tted with a residual heat indicator. When the oven is off,
the “residual heat” bar on the display lights up to indicate high temperatures
inside the oven cavity. The individual segments of the bar switch off one by
one as the temperature inside the oven falls.
Demo mode
The oven can operate in the DEMO mode: all heating elements are
deactivated, and the controls remain operative.To activate DEMO mode,
press and release button , then buttons “ ” and “ ” simultaneously for
6 seconds, and then press and release button .A buzzer sounds and the
TEMPERATURE display shows “dEon”. To deactivate DEMO mode, when
the oven is off press and hold button and button “ simultaneously
for 3 seconds. A buzzer sounds and the “dEoF” message disappears from
the display.
Restoring the factory settings
The oven factory settings can be restored to reset all selections made by
the user (clock and customised durations). To carry out a reset, switch off
the oven, then press and hold the button corresponding to the rst manual
cooking mode (top left) and the button simultaneously for 6 seconds.
Once the restore procedure is complete, a buzzer will sound. The rst time
the button is pressed, the oven will behave as if it is being switched
on for the rst time.
Standby
This product complies with the requirements of the latest European Directive
on the limitation of power consumption of the standby mode. If no buttons
are pressed for 30 minutes and the control panel/door lock has not been
activated, the appliance automatically reverts to standby mode. Standby mode
is indicated by the high luminosity “Clock button” light. As soon as interaction
with the machine resumes, the system’s operating mode is restored.
Modes
! Every time the oven is switched on, it suggests the rst manual cooking mode.
Manual cooking modes
! All cooking modes have a default cooking temperature which may be
adjusted manually to a value between 30°C and 250°C as desired (300°C
for GRILL mode). Any temperature adjustments will be stored in the
appliance memory and suggested again the next time this mode is used.
If the selected temperature is lower than the temperature inside the oven,
the text “Hot” appears on the TEMPERATURE display. However, it will still
be possible to start cooking.
MULTILEVEL mode
All heating elements and the fan are activated. Since the heat remains constant
throughout the oven, the air cooks and browns food in a uniform manner. A
maximum of two racks may be used at the same time.
BARBECUE mode
The top heating element and the rotisserie spit (where present) are activated.
The high and direct temperature of the grill is recommended for food which
requires a high surface temperature. Always cook in this mode with the oven
door closed (see “Practical cooking advice”).
FAN GRILLING mode
The top heating element and the rotisserie spit (where present) are activated
and the fan begins to operate. During part of the cycle the circular heating
element is also activated. This combination of features increases the
effectiveness of the unidirectional thermal radiation provided by the heating
elements through the forced circulation of the air throughout the oven.
This helps prevent food from burning on the surface and allows the heat to
penetrate right into the food. Always cook in this mode with the oven door
closed (see “Practical cooking advice”).
LOW TEMPERATURE modes
This type of cooking can be used for proving, defrosting, preparing yoghurt,
heating dishes at the required speed and slow cooking at low temperatures.
The temperature options are: 40, 65 and 90°C.
PIZZA modes
The top and circular heating elements switch on and the fan begins to operate.
This combination heats the oven rapidly. If you use more than one rack at a
time, switch the position of the dishes halfway through the cooking process.
BAKING mode
The rear heating element and the fan are switched on, thus guaranteeing the
distribution of heat in a delicate and uniform manner throughout the entire oven.
This mode is ideal for baking temperature sensitive foods (such as cakes,
which need to rise).
ECO mode
The back heating element is turned on and the fan starts working, ensuring
a smooth and uniform heat level inside the oven.
This programme is indicated for slow cooking of any type of food with
temperatures which can be set up to a maximum of 200°C; the programme
is also suitable for heating food and to complete the cooking process.
The programme is particularly suitable for the slow cooking of meat and sh,
as it allows you to have softer meat and save energy at the same time. For
a better energy effectiveness, when the product is turned on, the light stays
on only for 30 seconds; in order to turn the light back on, please press the
button
24
GB
Rotisserie spit
To operate the rotisserie function (see
diagram) proceed as follows:
1. Place the dripping pan in position 1.
2. Place the rotisserie support in
position 3 and insert the spit in the hole
provided on the back panel of the oven.
3. Start the rotisserie function by
selecting the or modes;
! When mode is on, the rotisserie
will stop if the door is opened.
Automatic cooking modes
! The temperature and cooking duration are pre-set values, guaranteeing
a perfect result every time - automatically. These values are set using the
C.O.P.® (Programmed Optimal Cooking) system. The cooking cycle stops
automatically and the oven indicates when the dish is cooked. You may start
cooking whether the oven has been preheated or not.
The cooking duration can be customised according to personal taste by
modifying the relevant value - before cooking begins - by ±5/20 minutes
depending on the selected programme. The duration can however be
modied even once cooking has begun. If the value is modied before the
programme begins, it is stored in the memory and suggested again by the
appliance when the programme is next used. If the temperature inside the
oven is higher than the suggested value for the selected mode, the text “Hot”
appears on the TEMPERATURE display and it will not be possible to begin
cooking; wait for the oven to cool.
! When the cooking stage has been reached, the oven buzzer sounds.
! Do not open the oven door as this will disrupt the cooking time and
temperature.
BEEF mode
Use this function to cook beef, pork and lamb. Place the food inside the oven
while it is still cold. The dish may also be placed in a preheated oven.
FISH FILLETS mode
This function is ideal for cooking small-medium llets. Place the food inside
the oven while it is still cold.
BREAD mode
Use this function to bake bread. To obtain the best results, we recommend
that you carefully observe the instructions below:
follow the recipe;
do not exceed the maximum weight of the dripping pan;
remember to pour 50 g (0,5 dl) of cold water into the baking tray in
position 5.
The dough must be left to rise at room temperature for 1 – 1 ½ hours
(depending on the room temperature) or until the dough has doubled in
size.
Recipe for BREAD:
1 Dripping pan holding 1000 g Max, lower level
2 Dripping pans each holding 1000 g Max, medium and lower levels
Recipe for 1000 g of dough: 600 g our, 360 g water, 11g salt, 25 g fresh yeast
(or 2 sachets of powder yeast)
Method:
Mix the our and salt in a large bowl.
Dilute the yeast in lukewarm water (approximately 35 degrees).
Make a small well in the mound of our.
Pour in the water and yeast mixture.
Knead the dough by stretching and folding it over itself with the palm of
your hand for 10 minutes until it has a uniform consistency and is not too
sticky.
Form the dough into a ball shape, place it in a large bowl and cover it with
transparent plastic wrap to prevent the surface of the dough from drying
out. Select the manual LOW TEMPERATURE function on the oven and
set the temperature to 40°C. Place the bowl inside and leave the dough
to rise for approximately 1 hour (the dough should double in volume).
Cut the dough into equal sized loaves.
Place them in the dripping pan, on a sheet of baking paper.
Dust the loaves with our.
Make incisions on the loaves.
Place the food inside the oven while it is still cold.
Start the BREAD cooking mode.
Once baked, leave the loaves on one of the grill racks until they have
cooled completely.
BAKED CAKES mode
This function is ideal for cooking desserts which are made using natural yeast,
baking powder and desserts which contain no yeast. Place the dish in the
oven while it is still cold. The dish may also be placed in a preheated oven.
TARTS mode
This function is ideal for all tart recipes (which normally need to be heated
well from underneath). Place the food inside the oven while it is still cold.
The dish may also be placed in a preheated oven.
Programming cooking
! A cooking mode must be selected before programming can take place.
! Once a cooking mode has been selected, the button is activated; it will
then be possible to program a duration. The button is only activated after
a duration has been set; it will then be possible to program a delayed start.
Programming the duration
1. Press the button; the button and the numbers on the TIME
display will ash.
2. Set the duration by pressing buttons “ ” and “ ”.
3. Once you have reached the desired duration, press the button again.
4. Press the button to begin cooking.
5. When cooking has nished, “END” appears on the TEMPERATURE display
and a buzzer sounds.
For example: it is 9:00 a.m. and a duration of 1 hour and 15 minutes is
programmed. The programme will stop automatically at 10:15 a.m.
GB
25
Programming delayed cooking
! A cooking duration must be set before the cooking end time can be scheduled.
! For the delayed programming to work properly, the clock should be set to
the correct time.
1. Press the button and repeat steps 1 to 3 as described for the duration
setting.
2. Then press the button and set the end time using the “ ” and “
” buttons.
3. Once you have reached the desired end time, press the button again.
4. Press the button to activate the programmed mode.
The and buttons will ash alternately to indicate that programming
has taken place; in the time before cooking starts, the TIME display will show
the duration and the cooking end time alternately.
5. Once cooking has nished, “END” appears on the TEMPERATURE display
and a buzzer sounds.
For example: it is 9:00 a.m. and a time of 1 hour and 15 minutes is
programmed, while the end time is set to 12:30. The programme will
start automatically at 11:15 a.m.
To cancel programming press the button.
Practical cooking advice
! Do not place racks in position 1 and 5 during fan-assisted cooking. This is
because excessive direct heat can burn temperature sensitive foods.
! In the GRILL and FAN GRILLING cooking modes, particularly when using
the rotisserie spit, place the dripping pan in position 1 to collect cooking
residues (fat and/or grease).
MULTILEVEL
Use positions 2 and 4, placing the food which requires more heat on 2.
Place the dripping pan on the bottom and the rack on top.
GRILL
Place the rack in position 3 or 4. Position the food in the centre of the rack.
We recommend that the temperature is set to its maximum level. The top
heating element is regulated by a thermostat and may not always operate
constantly.
PIZZA
Use a lightweight aluminium pizza pan. Place it on the rack provided.
For a crispy crust, do not use the dripping pan as this extends the total
cooking duration and prevents the crust from forming.
If the pizza has a lot of toppings, we recommend adding the mozzarella
cheese to the top of the pizza halfway through the cooking process.
26
GB
Modes FoodsWeight
(in kg)
Preheating
Manual
Standard
guide
rails
Sliding
guide
rails
Multilevel*
1+1
1
1
1
2 and 4
2 and 4
2 and 4
1 and 2/3
2
1 or 2
2
2 and 4
1 and 3
1 and 3
1 and 3
1 and 3
1 and 3
1
1
1
1 and 3
1 and 3
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
20-25
30-35
20-30
65-75
45-50
30-35
35-40
20-25
10-20
20-25
25-35
Grill*
1
0,7
0,7
0,7
0,5
0,8
0,7
4 or 5
4 or 6
1
1
4
4
4
4
3 or 4
4
4
4
4
-
-
3
3
3
3
2 or 3
3
3
3
3
-
-
no
no
no
no
no
no
no
no
no
no
no
300
300
300
300
300
300
300
300
300
300
300
10-20
10-15
10-15
10-15
15-20
10-20
10-20
10-12
3-5
70-80
70-80
Fan grilling*
1,5
1
1,5
1,5
1
1
1
2
2
-
-
2
2
2
2
2
-
-
2
2
2
no
no
no
no
no
no
no
210
200
210
210
210
210
210
55-60
30-35
70-80
60-70
60-75
70-80
40-45
Proving / Defrosting
White meringues
Meat / Fish
-
-
-
2
2
2
1
1
1
no
no
no
40
65
90
-
8-12 ore
90-180
Pizza*
Pi zza
Focaccia bread
0,5
0,5
2
2
1
1
yes
yes
15-20
20-25
Baking*
0,5
1
0,7
0,7
0,6
0,7
0,7
0,8
0,5
0,5
2 or 3
2 or 3
2 or 3
2 and 4
2 or 3
1 and 3
1 and 3
2
1 and 3
2
1 or 2
1 or 2
1 or 2
1 and 3
1 or 2
1 and 2
1 and 2
1
1 and 2
1
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
180
180
180
180-190
160-170
180-190
180
200
90
210
25-35
40-50
45-55
20-25
35-40
20-30
20-25
30-35
180
20-25
Automatic**
Beef
Roast dishes12 or 32 no
Fish fillets
Cod
Perch
Trout
0,4-0,5
0,4-0,5
0,4-0,5
2 or 3
2 or 3
2 or 3
2
2
2
no
no
no
Bread***
Bread (see recipe)
11 or 21 no
Baked cakes
Baked cakes
12 or 32 no
Tarts
Tarts
0,52 or 32 no
Cooking advice table
Low
temperature*
Rack position Recommended
Temperature
(°C)
Cooking
duration
(minutes)
1 and 3 and 5
1 and 3 and 5
1 and 2 and 4
1 and 2 and 4
50 0,5
210-220
180
160-170
200-210
190-200
180
180-190
190
180
210
190-200
210-220
190-200
! ECO programme: This programme can be used for slow cooking of any type of food with temperatures which can be set up to a maximum of 200°C;
the programme is also suitable for heating food and to complete the cooking process.
GB
27
Precautions and tips
! This appliance has been designed and manufactured in compliance with
international safety standards. The following warnings are provided for safety
reasons and must be read carefully.
General safety
The appliance was designed for domestic use inside the home and is
not intended for commercial or industrial use.
The appliance must not be installed outdoors, even in covered areas. It is
extremely dangerous to leave the appliance exposed to rain and storms.
When moving or positioning the appliance, always use the handles
provided on the sides of the oven.
Do not touch the appliance while barefoot or with wet or damp hands and
feet.
The appliance must be used by adults only for the preparation of
food, in accordance with the instructions provided in this booklet.
Any other use of the appliance (e.g. for heating the room) constitutes
improper use and is dangerous. The manufacturer may not be held
responsible for any damage caused as a result of improper, incorrect
and unreasonable use of the appliance.
Do not touch the heating elements or certain parts of the oven door
when the appliance is in use; these parts become extremely hot.
Keep children well away from the appliance.
Make sure that the power supply cables of other electrical appliances do
not come into contact with the hot parts of the oven.
The ventilation and heat dispersal openings must never be obstructed.
Always grip the oven door handle in the centre: the ends may be hot.
Always use oven gloves when placing cookware in the oven or when
removing it.
Do not use aluminium foil to line the bottom of the oven.
Do not place ammable materials in the oven: if the appliance is switched
on accidentally, the materials could catch re.
When unplugging the appliance, always pull the plug from the mains
socket; do not pull on the cable.
Do not perform any cleaning or maintenance work without having
disconnected the appliance from the electricity mains.
If the event of malfunctions, under no circumstances should you attempt
to perform the repairs yourself. Contact an authorised Service Centre (see
Assistance).
Do not rest objects on the open oven door.
Do not let children play with the appliance.
The appliance should not be operated by people (including children)
with reduced physical, sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with the product. These
individuals should, at the very least, be supervised by someone who
assumes responsibility for their safety or receive preliminary instructions
relating to the operation of the appliance.
The appliance is not intended to be operated by means of an external
timer or separate remote-control system.
Disposal
When disposing of packaging material: observe local legislation so that
the packaging may be reused.
The European Directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE), requires that old household electrical
appliances must not be disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected separately in order
to optimise the recovery and recycling of the materials they contain
and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
Respecting and conserving the environment
Whenever possible, avoid pre-heating the oven and always try to ll it.
Open the oven door as little as possible because heat is lost every time it
is opened. To save a substantial amount of energy, simply switch off the
oven 5 to 10 minutes before the end of your planned cooking time and
use the heat the oven continues to generate.
Automatic programmes are based on standard food product.
Keep gaskets clean and tidy to prevent any door energy losses
If you have a timed tariff electricity contract, the “delay cooking” option
will make it easier to save money by moving operation to cheaper time
periods.
! This product complies with the requirements of the latest European Directive
on the limitation of power consumption of the standby mode.
28
GB
Maintenance and care
Switching the appliance off
Disconnect your appliance from the electricity supply before carrying out
any work on it.
Cleaning the appliance
Slight differences in colour on the front of the oven are due to the different
materials used, i.e. glass, plastic or metal.
Any shady areas resembling grooves on the oven door glass are caused
by reections from the oven light.
The enamel is branded at very high temperatures. This process may cause
colour variations. This is normal and will not affect appliance operation in
any way. The thin edges of the sheet metal cannot be entirely enamelled
and may therefore appear to be unnished. This will not affect the rust
protection.
The stainless steel or enamel-coated external parts and the rubber seals
may be cleaned using a sponge that has been soaked in lukewarm water
and neutral soap. Use specialised products for the removal of stubborn
stains. After cleaning, rinse and dry thoroughly. Do not use abrasive
powders or corrosive substances.
The inside of the oven should ideally be cleaned after each use, while it is
still lukewarm. Use hot water and detergent, then rinse well and dry with
a soft cloth. Do not use abrasive products.
All accessories - with the exception of the sliding racks - can be washed
like everyday crockery, and are even dishwasher safe.
We recommend that detergents are not sprayed directly onto the control
panel, but that a sponge is used instead.
! Never use steam cleaners or pressure cleaners on the appliance.
Cleaning the oven door
Clean the glass part of the oven door using a sponge and a non-abrasive
cleaning product, then dry thoroughly with a soft cloth. Do not use rough
abrasive material or sharp metal scrapers as these could scratch the surface
and cause the glass to crack.
For more thorough cleaning purposes, the oven door may be removed:
1. Open the oven door fully (see diagram).
2. Use a screwdriver to lift up and turn the small levers F located on the two
hinges (see diagram).
F
3. Grip the door on the two outer sides and
close it approximately half way. Pull the
door towards you, lifting it out of its slot (see
diagram). To replace the door, reverse this
sequence.
Inspecting the seals
Check the door seals around the oven regularly. If the seals are damaged,
please contact your nearest Service Centre (see Assistance). We recommend
that the oven is not used until the seals have been replaced.
Replacing the light bulb
To replace the oven light bulb:
1. Remove the glass cover of the
lamp-holder.
2. Remove the light bulb and replace
it with a similar one: Wattage 25 W,
cap E 14.
3. Replace the glass cover (see
diagram).
! Do not use the oven lamp as/for ambient lighting.
Sliding rack kit assembly
To assemble the sliding racks:
1. Remove the two frames, lifting them
away from the spacers A (see gure).
2. Choose which shelf to use with the
sliding rack. Paying attention to the
direction in which the sliding rack is to
be extracted, position joint B and then
joint C on the frame.
3. Secure the two frames with the guide
rails using the holes provided on the
oven walls (see diagram). The holes
for the left frame are situated at the
top, while the holes for the right frame
are at the bottom.
4. Finally, t the frames on the spacers
A.
! Do not place the sliding racks in position 5.
A
B
C
Left
guide rail
Right guide
rail
Direction
of extraction
D
GB
29
Side and rear catalytic liners
These are panels coated with a special enamel, which is able to absorb the
fat released by food as it cooks.
This enamel is quite strong, so that the various accessories (racks, dripping
pans, etc.) can slide along them without damaging them. White marks may
appear on the surfaces; these are not a cause for concern.
Nevertheless, the following should be avoided:
- scraping the enamel with sharp objects (a knife, for example);
- using detergents or abrasive materials.
The “Clock button” and the digits on the
display flash.
The appliance has just been connected to the
electricity mains or there has been a blackout.
Set the clock.
A programmed cooking mode does not
start.
There has been a blackout.
Reprogram the cooking mode.
Only the high luminosity “Clock button”
is lit.
The appliance is in standby mode. Press any button to exit standby mode.
The temperature inside the oven is higher
than the suggested value for the selected
mode.
An automatic mode has been selected.
“Hot” appears on the display and
cooking does not start.
Wait for the oven to cool down.
Fan-assisted cooking has been
selected and the food looks burnt.
Positions 1 and 5: the direct heat could cause
temperature-sensitive foods to burn.
We recommend switching dripping pan
positions halfway through cooking.
Troubleshooting
60
PT
195122967.00
08/2014 - XEROX FABRIANO
Indesit Company S.p.A.
V
iale Aristide Merloni,47
60044 Fabriano (AN)
www.hotpoint.eu
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Hotpoint FH 1039 0 XA/HA Owner's manual

Category
Ovens
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI