Xavax 00111942 Specification

Brand: Xavax

Model: 00111942

Category: Energy cost meters

Type: Specification

The Xavax 00111942 energy cost meter is a handy tool that helps you identify power-guzzling devices in your home or office, allowing you to save money and contribute to environmental protection. By replacing old appliances with energy-efficient ones (class A, A+, A++), you can significantly reduce your electricity consumption. For example, switching from an old refrigerator to an energy-efficient A++ model can save you up to 300 kWh or 60 euros annually.

Page is loading ...

g Operating Instruction

The energy cost meter allows you to ﬁnd the “power

guzzling” devices in your home or ofﬁce both quickly

and easily. By replacing these devices with energy-

saving devices (such as class A, A+, A++), you can

save money and make an important contribution to the

environment. Example: By replacing an older refrige-

rator (approx. 15 years old) with an energy-saving A++

device, you can save up to 300 kWh annually or up to

EUR 60 (based on a tariff of EUR 0.20/kWh).

Read the safety instructions and notes carefully

before using your energy cost meter.

Important safety instructions:

The voltage or power of the connected devices

must not exceed 230 V or 3,680 W. Please note the

information printed on the type plate of the connected

devices.

Make sure that the passed-through protective

conductor is not blocked. In the case of a fault, this

could result in fatal injury. Only connect the device to

an electrical socket that has been approved for the

device. The electrical socket must always be easily

accessible.

The device is not protected against drops or splashes

of water. Do not let the product come into contact with

rain, moisture or other liquids to avoid damaging the

device and to prevent injuries due to short circuits.

We do not recommend that you operate this device

in environments exposed to ﬂammable gases, fumes

or dust. When cleaning the device, make sure that

it is disconnected from power. Do not operate this

device in a moist environment or when the device

itself is moist.

Never use or open a defective device. Repair work

may only be conducted by an authorised specialist. As

with all electronic devices, keep the device out of the

reach of children.

We shall not accept any liability for damage to materi-

als or injury to persons resulting from non-observance

of these safety instructions or improper use. The

energy meter is not approved for the calculation of

electricity costs owed to the energy provider by the

consumer.

Getting started:

1. Button Functions:

MODE: Switches to different displays

SET: Switches to mode

UP: Changes the selected place in the number

Allows you to switch between the values

0-9 incrementally

2. Display:

1. W (Watt):

Display the current power consumption

up to max. 3680 W

2. kWh: Displays the used kilowatt hours up to

max. 9999.99 kWh (corresponds to energy

consumption since the last reset)

3. PRICE:

Displays the total costs up to max 9,999.99

(corresponds to the cost since the

last reset)

4. COSTS/kWh: Displays the set tariff up to max

99,99/kWh

MODE SET UP

00111942man_de_en_es_fr_nl.indd 4 18.08.11 11:38

3. Basic Settings:

First, set the price of a single kilowatt hour (kWh). You

can ﬁnd this information in your last electricity bill or

you can ask your electricity company to supply you

with the current price.

a) Plug the energy meter (without a consumer such

as a TV) into a standard CEE 7/4 electrical socket

(230 V/50 Hz). After approx. 5 seconds the power

consumption (in Watts) appears on the display.

b) Press the SET button three times until the display

shows „COST/kWh”. The last set value is saved by

pressing the MODE button once when you exit the

menu. Using the button, you can select the place that

you wish to change and using the UP button, you can

choose the desired value by switching the values 0-9

incrementally. If you would like to change the value

back to a lower number, keep pressing the button.

Once the display reaches 9, it starts back at 0. The

last value is automatically saved. The last set value is

saved by pressing the MODE button once when you

exit the menu.

4. Measuring:

Press the MENU button to return to the main menu.

Now connect the plug of the electrical device (e.g. TV)

to the energy meter. The consumption measurements

begin automatically. You can switch between the

different displays by pressing the MODE button. Once

you have carried out the desired measurements,

remove the energy cost meter from the electrical

socket.

Technical speciﬁcations:

Operating voltage: AC 230 V/50 Hz

Range of use: 1 W to 3,680 W

Consumption measurement: 0.01 kWh to 9999.99 kWh

Resolution: 0,1 W

Accuracy:

W (watts): 0-100 W: +/- 1% or +/- 1 W

100-3680 W: +/- 1%

kWh (kilowatt hours): +/-1%

Device power consumption: approx. 0.5 W

00111942man_de_en_es_fr_nl.indd 5 18.08.11 11:38

Page is loading ...

00111942/08.11

Distributed by Hama GmbH & Co KG

D-86651 Monheim/Germany

+49 9091 502-0

www.xavax.eu

00111942man_de_en_es_fr_nl.indd 12 18.08.11 11:38

Xavax 00111942 Specification

Brand: Xavax

Model: 00111942

Category: Energy cost meters

Type: Specification

Download PDF

report

Xavax 00111942 Specification

Xavax 00111942 Specification

in other languages

Related papers

Other documents