Acer PN-X10 User manual

Acer Projector

U5200/N210/PN-X10/U5300W/N220/

PN-W10 Series

User's Guide

Acer Projector U5200/N210/PN-X10/U5300W/N220/PN-W10 Series User's Guide

Original Issue: 12/2010

Acer Projector U5200/N210/PN-X10/U5300W/N220/PN-W10 Series

Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'

product names or trademarks are used herein for identification purposes only and belong to

their respective companies.

"HDMI

TM

, the HDMI logo and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC."

Changes may be made periodically to the information in this publication without obligation

to notify any person of such revisions or changes. Such changes will be incorporated in new

editions of this manual or supplementary documents and publications. This company makes

no representations or warranties, either expressed or implied, with respect to the contents

hereof and specifically disclaims the implied warranties of merchantability or fitness for a

particular purpose.

Record the model number, serial number, purchase date and place of purchase information in

the space provided below. The serial number and model number are recorded on the label

affixed to your projector. All correspondence concerning your unit should include the serial

number, model number and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in

any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,

without the prior written permission of Acer Incorporated.

Model number: __________________________________

Serial number: ___________________________________

Date of purchase: ________________________________

Place of purchase: ________________________________

iii

Information for Your Safety and

Comfort

Read these instructions carefully. Keep this document for future reference.

Follow all warnings and instructions marked on the product.

Turning the product off before cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Caution for plug as disconnecting device

Observe the following guidelines when connecting and disconnecting power to

the external power supply unit:

• Install the power supply unit before connecting the power cord to the AC

power outlet.

• Unplug the power cord before removing the power supply unit from the

projector.

• If the system has multiple sources of power, disconnect power from the

system by unplugging all power cords from the power supplies.

Caution for Accessibility

Be sure that the power outlet you plug the power cord into is easily accessible

and located as close to the equipment operator as possible. When you need to

disconnect power to the equipment, be sure to unplug the power cord from the

electrical outlet.

Warnings!

• Do not use this product near water.

• Do not place this product on an unstable cart, stand or table. If the product

falls, it could be seriously damaged.

• Slots and openings are provided for ventilation to ensure reliable

operation of the product and to protect it from overheating. These

openings must not be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug or other similar surface.

This product should never be placed near or over a radiator or heat register, or

in a built-in installation unless proper ventilation is provided.

• Never push objects of any kind into this product through cabinet slots as

they may touch dangerous voltage points or short-out parts that could

result in a fire or electric shock. Never spill liquid of any kind onto or into

the product.

iv

• To avoid damage of internal components and to prevent battery leakage,

do not place the product on a vibrating surface.

• Never use it under sporting, exercising, or any vibrating environment

which will probably cause unexpected short current or damage rotor

devices, lamp.

Using electrical power

• This product should be operated from the type of power indicated on the

marking label. If you are not sure of the type of power available, consult

your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this

product where people will walk on the cord.

• If an extension cord is used with this product, make sure that the total

ampere rating of the equipment plugged into the extension cord does not

exceed the extension cord ampere rating. Also, make sure that the total

rating of all products plugged into the wall outlet does not exceed the fuse

rating.

• Do not overload a power outlet, strip or receptacle by plugging in too

many devices. The overall system load must not exceed 80% of the branch

circuit rating. If power strips are used, the load should not exceed 80% of

the power strip's input rating.

• This product's AC adapter is equipped with a three-wire grounded plug.

The plug only fits in a grounded power outlet. Make sure the power outlet

is properly grounded before inserting the AC adapter plug. Do not insert

the plug into a non-grounded power outlet. Contact your electrician for

details.

Warning! The grounding pin is a safety feature. Using a power outlet that is

not properly grounded may result in electric shock and/or injury.

Note: The grounding pin also provides good protection from unexpected

noise produced by other nearby electrical devices that may interfere with

the performance of this product.

• Use the product only with the supplied power supply cord set. If you need

to replace the power cord set, make sure that the new power cord meets

the following requirements: detachable type, UL listed/CSA certified, VDE

approved or its equivalent, 4.6 meters (15 feet) maximum length.

v

Product servicing

Do not attempt to service this product yourself, as opening or removing covers

may expose you to dangerous voltage points or other risks. Refer all servicing to

qualified service personnel.

Unplug this product from the wall outlet and refer servicing to qualified service

personnel when:

• the power cord or plug is damaged, cut or frayed

• liquid was spilled into the product

• the product was exposed to rain or water

• the product has been dropped or the case has been damaged

• the product exhibits a distinct change in performance, indicating a need

for service

• the product does not operate normally after following the operating

instructions

Note: Adjust only those controls that are covered by the operating

instructions, since improper adjustment of other controls may result in

damage and will often require extensive work by a qualified technician to

restore the product to normal condition.

Warning! For safety reasons, do not use non-compliant parts when adding

or changing components. Consult your reseller for purchase options.

Your device and its enhancements may contain small parts. Keep them out of

the reach of small children.

Additional safety information

• Do not look into the projector's lens when the lamp is on. The bright light

may hurt your eyes.

• Turn on the projector first and then signal sources.

• Do not place the product in the following environments:

• Space that is poorly ventilated or confined. At least 50cm clearance from walls

and free flow of air around the projector are necessary.

• Locations where temperatures may become excessively high, such as inside of a

car with all windows rolled up.

• Locations where excessive humidity, dust, or cigarette smoke may contaminate

optical components, shorten the life span and darken the image.

• Locations near fire alarms.

• Locations with an ambient temperature above 40 ºC/104 ºF.

• Locations where the altitudes are higher than 10000 feet.

• Unplug immediately if there is something wrong with your projector. Do

not operate if smoke, strange noise or odor comes out of your projector. It

vi

might cause fire or electric shock. In this case, unplug immediately and

contact your dealer.

• Do not keep using this product to break or drop it. In this case contact your

dealer for inspection.

• Do not face the projector lens to the sun. It can lead to fire.

• When switching the projector off, please ensure the projector completes

its cooling cycle before disconnecting power.

• Do not frequently turn off the main power abruptly or unplug the

projector during operation. The best way is to wait for the fan to stop

before turning main power off.

• Do not touch the air outlet grille and bottom plate which become hot.

• Clean the air filter frequently. The temperature inside may rise and cause

damage when the filter/ventilation slots are clogged with dirt or dust.

• Do not look into the air outlet grille when projector is operating. It may

hurt your eyes.

• Always open the lens shutter or remove the lens cap when the projector is

on.

• Do not block the projector lens with any object when the projector is

under operation as this could cause the object to become heated and

deformed or even cause a fire. To temporarily turn off the lamp, press HIDE

on the remote control.

• The lamp becomes extremely hot during operation. Allow the projector to

cool for approximately 45 minutes prior to removing the lamp assembly for

replacement.

• Do not operate lamps beyond the rated lamp life. It could cause it to break

on rare occasions.

• Never replace the lamp assembly or any electronic components unless the

projector is unplugged.

• The product will detect the life of the lamp itself. Please be sure to change

the lamp when warning messages display.

• When changing the lamp, please allow the projector to cool down, and

follow all changing instructions.

• Reset the "Lamp Hour Reset" function from the Onscreen Display

"Management" menu after replacing the lamp module.

• Do not attempt to disassemble this projector. There are dangerous high

voltages inside which may hurt you. The only user serviceable part is the

lamp which has its own removable cover. Refer servicing only to suitable

qualified professional service personnel.

• Do not stand the projector on end vertically. It may cause the projector to

fall over, causing injury or damage.

• This product is capable of displaying inverted images for ceiling mount

installation. Only use acer ceiling mount kit for mounting the projector

and ensure it is securely installed.

vii

Cleaning the mirror

Clean the mirror whenever you notice dirt or dust on the surface.

• Use a canister of compressed air to remove dust.

• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens

cleaner and gently wipe the mirror.

• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile

solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or

maintaining prolonged contact with rubber or vinyl materials may result in damage

to the projector surface and cabinet material.

Caution for listening

To protect your hearing, follow these instructions.

• Increase the volume gradually until you can hear clearly and comfortably.

• Do not increase the volume level after your ears have adjusted.

• Do not listen to music at high volumes for extended periods.

• Do not increase the volume to block out noisy surroundings.

• Decrease the volume if you can't hear people speaking near you.

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize

pollution and ensure utmost protection of the global environment, please

recycle. For more information on the Waste from Electrical and Electronics

Equipment (WEEE) regulations, visit http://www.acer-group.com/public/

Sustainability/sustainability01.htm

Mercury advisory

For projectors or electronic products containing an LCD/CRT monitor or display:

Lamp(s) inside this product contain mercury and must be recycled or disposed of

according to local, state or federal laws. For more information, contact the

Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal

information, check www.lamprecycle.org

"Lamp(s) contain Mercury,

Dispose Properly."

viii

First Thing First

Usage Notes

Do:

• Turn off the product before cleaning.

• Use a soft cloth moistened with mild detergent to clean the display

housing.

• Disconnect the power plug from AC outlet if the product is not being used

for a long period of time.

Don't:

• Block the slots and openings on the projector provided for ventilation.

• Use abrasive cleaners, waxes or solvents to clean the unit.

• Use under the following conditions:

• In extremely hot, cold or humid environments.

• In areas susceptible to excessive dust and dirt.

• Near any appliance that generates a strong magnetic field.

• Place in direct sunlight.

Precautions

Follow all warnings, precautions and maintenance as recommended in this

user's guide to maximize the life of your unit.

Warning:

• Do not look into the projector's lens when the lamp is on. The bright light may hurt

your eyes.

• To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

• Please do not open or disassemble the product as this may cause electric shock.

• When changing the lamp, please allow the projector to cool down, and follow all

changing instructions.

• This product will detect the life of the lamp itself. Please be sure to change the lamp

when it shows warning messages.

• Reset the "Lamp Hour Reset" function from the Onscreen Display "Management"

menu after replacing the lamp module.

• When switching the projector off, please ensure the projector completes its cooling

cycle before disconnecting power.

• Turn on the projector first and then the signal sources.

• Do not use lens cap when projector is in operation.

• When the lamp reaches the end of its life, it will burn out and may make a loud

popping sound. If this happens, the projector will not turn back on until the lamp

module has been replaced. To replace the lamp, follow the procedures listed under

"Replacing the Lamp".

Information for Your Safety and Comfort iii

First Thing First viii

Usage Notes viii

Precautions viii

Introduction 1

Product Features 1

Package Overview 2

Projector Overview 3

Projector Outlook 3

Control Panel 4

Remote Control Layout 5

Getting Started 7

Connecting the Projector 7

Turning the Projector On/Off 8

Turning On the Projector 8

Turning Off the Projector 9

Adjusting the Projected Image 10

Adjusting the Height of the Projected Image 10

How to Optimize Image Size and Distance 11

How to Get a Preferred Image Size by Adjusting

Distance and Zoom 13

User Controls 15

Installation Menu 15

Acer Empowering Technology 16

Onscreen Display (OSD) Menus 17

Color 18

Image 20

Setting 22

Management 26

Audio 27

Timer 27

Language 28

Appendices 29

Contents

Troubleshooting 29

LED & Alarm Definition Listing 33

Replacing the Lamp 34

Ceiling Mount Installation 35

Specifications 38

Compatibility Modes 40

Regulations and safety notices 44

1

English

Introduction

Product Features

This product is a single-chip DLP

®

projector, including the following

outstanding features:

• DLP

®

technology

• U5200/N210/PN-X10: Native 1024 x 768 XGA resolution

Auto / 4:3 / 16:9 aspect ratio supported

U5300W/N220/PN-W10: Native 1280 x 800 WXGA resolution

Auto / Full / 4:3 / 16:9 / L.Box aspect ratio supported

• Acer ColorBoost technology delivers vivid, life-like images

• High brightness and contrast ratio

• Versatile display modes enable optimum performance in any situation

• NTSC/PAL/SECAM compatible and HDTV (720p, 1080i, 1080p) supported

• Lower power consumption and economy (ECO) mode extends lamp life

• Acer EcoProjection Technology delivers Intelligent power management

approach and physical efficiency improvement

• Empowering Key reveals Acer Empowering Technology functions (Acer

eView, eTimer, eOpening, ePower Management) for easy adjustment of

settings

• Advanced keystone correction delivers optimum presentations

• Multi-language Onscreen Display (OSD) menus

• Full-function remote control

• 2X digital zoom and pan move function

• Microsoft

®

Windows

®

2000, XP, 7, Vista

®

OS compliant

• LAN settings enable remote management of projectors via a web browser

• Ability to display 3D images

• Top-loading lamp design allows easy lamp replacement

• Ultra-short-throw feature is good for installation

2

English

Package Overview

This projector comes with all the items shown below. Check to make sure you

have them all. Contact your dealer immediately if any thing is missing.

Projector Power cord VGA cable

Composite video cable

Security card User’s guide (CD-ROM)

Remote control Quick start guide Battery x 2

Dust filter

(Optional)

Acer Projector Gateway (CD-

ROM)

Acer Projector Gateway

quick start guide

Acer Projector

Quick Start Guide

Acer Projector Gateway

Quick Start Guide

3

English

Projector Overview

Projector Outlook

Front / upper side

Rear side

# Description # Description

1 Mirror 5 Tilt adjusting wheel

2 Focus ring 6 Mirror door release button

3 Projection lens 7 Control panel

4 Remote control receiver 8 Power key and Power indicator

LED

# Description # Description

1 12V DC output connector 8 Audio input connector/

Audio output connector

2 USB connector (Type mini B)

3 RS232 connector 9 S-Video input connector/

Composite video input connector

4 Monitor loop-through output

connector

10 Tilt adjusting wheel

5 PC analog signal/HDTV/component

video input connector (VGA IN 1/

VGA IN 2)

11 LAN (RJ45 port for 10/100M

Ethernet)

6 HDMI connector 12 USB connector (Type A)

7 Microphone input connector 13 Power socket

14 Kensington™ lock port

7

6

2

8

4

1

3

5

4

6

5732189

10

10 1411 1312

4

English

Control Panel

# Function Description

1 Remote control receiver Receives the signal emitted from the

remote control

2 Empowering key Enables unique Acer functions: eView,

eTimer, eOpening, ePower Management.

3 TEMP Temp indicator LED

4 Keystone Adjusts image distortion caused by tilting

projection (±15 degrees).

5MENU

• Launches the Onscreen Display (OSD)

menu, returns to the previous step for

the OSD menu operation or exits the

OSD menu.

• Confirms your selection of items.

6 SOURCE Chooses RGB, component video, S-Video,

composite video, HDMI™ or HDTV source.

7 Power key and Power

indicator LED

Refer to the "Turning the Projector On/

Off" section.

8 LAMP Lamp indicator LED

9 Four directional select keys Selects items or makes adjustments to your

selection.

10 RESYNC Automatically synchronizes the projector

to the input source.

11 Mirror door release button Press the button to release the mirror door.

7

8

11

10

9

1

5

6

4

2

3

5

English

Remote Control Layout

# Function Description

1 Infrared

transmitter

Sends signals to the projector.

2 POWER Refer to the "Turning the Projector On/Off" section.

3 FREEZE To pause the screen image.

4 RESYNC Automatically synchronizes the projector to the input

source.

5 BACK Goes back to the previous selection.

6 Keystone Adjusts image distortion caused by tilting projection

(±15 degrees).

Four

directional

select keys

Selects items or makes adjustments to your selection.

7 Mouse

button

This function is not available with the projector.

8Four

directional

select pad

Selects the media files in four directions.

9 VOL +/- Increases/decreases the volume.

10 Empowering key Enables unique Acer functions: eView, eTimer,

eOpening, ePower Management.

6

English

11

Rewind

Play/Pause

Stop

Fast-forward

Rewinds/Plays/Pauses/Stops/Fast-forwards the playing

media files.

12 VGA To change source to VGA. This connector supports

analog RGB, YPbPr (480p/576p/720p/1080i/1080p),

and YCbCr (480i/576i).

13 COMPONENT To change source to Component video. This

connector supports YPbPr.

14 SD/USB A To change source to SD/USB A. This projector supports

various formats for photo/audio/video files.

15 HDMI™/DVI To change source to HDMI™/DVI (for the model with

HDMI™/DVI connector).

16 Keypad 0~9 Press "0~9" to input a password in the "Setting >

Security" OSD.

17 Laser pointer

window

Shines the laser point light when the Laser button is

pressed.

18 HIDE Press "HIDE" to hide screen image; press again to

display the image.

19 ASPECT RATIO To choose the desired aspect ratio.

20 SOURCE Chooses RGB, component video, S-Video, composite

video, HDMI™, or HDTV source.

21 ZOOM Zooms the projector display in or out.

22 ENTER Confirms your selection of items.

23

Laser

Emits visible laser pointer light for presentation

purposes. This function is not available for the

projectors sold in the Japanese market.

24 MENU Launches the Onscreen Display (OSD) menu, returns

to the previous step for the OSD menu operation or

exits the OSD menu.

25 PAGE ^/v For computer mode only. Use the button to select the

next or previous page. This function is only available

when connected to a computer via a USB cable.

26 S-VIDEO To change source to S-Video.

27 VIDEO To change source to Composite video.

28 USB B To change source to USB B.

29 LAN/WiFi To change source to LAN/WiFi. (for LAN/wireless

compatible models)

# Function Description

7

English

Getting Started

Connecting the Projector

Note: To ensure the projector works well with your computer,

please make sure the timing of the display mode is compatible

with the projector.

Note: "*" USB drive limitation, do not support power.

# Description # Description

1 Power cord 8 HDMI cable

2 VGA cable 9 3 RCA component cable

3 VGA to component video/HDTV

adapter

10 RJ45 cable

4 Composite video cable 11 USB cable

5 Audio cable 12* USB storage device/USB Wifi adapter

(Optional)

6 S-Video cable 13 12V DC cable

7 RS232 cable

RS232

RBG

HDTV adapter

D-Sub

7

D-Sub

2

8

5

6

4

5

2

1

Y

R

L

9

3

Y

10

11

10

USB

12

13

DVD player, Set-top

box, HDTV receiver

VGA

RS232

S-Video/

Video Output

Speakers

Display

Microphone

Screen

8

English

Turning the Projector On/Off

Turning On the Projector

1 Press OPEN on the control panel to release the mirror door.

2 Ensure that the power cord and signal cable are securely connected.

The Power LED will light red.

3 Turn on the projector by pressing (POWER) on the control panel or

remote control, and the Power indicator LED will turn blue.

4 Turn on your source (computer, notebook, video player, etc.). The

projector will detect your source automatically.

• If the screen displays "No Signal", please make sure the signal cables

are securely connected.

• If you connect to multiple sources at the same time, use "SOURCE" on

the control panel or remote control, or the direct source key on the

remote control to switch between inputs.

Note: When the mirror door is closed for over 5 seconds, the

projector will shut down and cool down for 120 seconds, then

enter to a stanby mode.

1

2 3

9

English

Turning Off the Projector

1 To turn the projector off, press the power button. This message

appears:

"Please press the power button again to complete the shutdown process."

Press the power button again.

2 The LED power indicator will turn RED and blink rapidly after the

projector is turned off, and the fan(s) will continue to operate for

about 2 minutes to ensure that the system cools properly.

3 As long as the power cord remains plugged in, you can press the

power button to turn the projector immediately back on anytime

during the 2-minute shutdown process.

4 Once the system has finished cooling, the LED power indicator will

stop blinking and turn solid red to indicate standby mode.

5 It is now safe to unplug the power cord.

Warning indicators:

• "Projector Overheated. Lamp will automatically turn off soon."

This onscreen message indicates that the projector has overheated.

The lamp will automatically turn off, the projector will automatically

shut down, and the LED temp indicator will turn solid red. Contact

your local dealer or service center.

• "Fan failed. Lamp will automatically turn off soon."

This onscreen message indicates that the fan has failed. The lamp will

automatically turn off, the projector will automatically shut down,

and the LED temp indicator will blink. Contact your local dealer or

service center.

Note: Whenever the projector automatically shuts down and

the

LED lamp indicator turns solid red, contact your local

reseller or service center

.

10

English

Adjusting the Projected Image

Adjusting the Height of the Projected Image

The projector is equipped with an elevator foot for adjusting the image height.

To raise the image:

Use Tilt adjusting wheel to fine-tune the display angle.

To lower the image:

Use Tilt adjusting wheel to fine-tune the display angle.

Tilt adjusting wheel Tilt adjusting wheel

Page is loading ...

Acer PN-X10 User manual

This manual is also suitable for

Acer PN-X10 User manual

Related papers

Other documents