Biostar TA75A+ User manual

TA75A+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Dichiarazione di conformità

sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è

conforme alle normative vigenti e

soddisfa i requisiti essenziali richiesti

dalle direttive

2004/108/CE, 2006/95/CE e

1999/05/CE

quando ad esso applicabili

Short Declaration of conf ormity

We declare this product is complying

with the laws in force and meeting all

the essential requirements as specified

by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU) ....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................. 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: AMD DUAL Graphics Technology ......... 19

4.1 AMD Dual Graphics Technology Introduction............................. 19

4.2 AMD Dual Graphics Requirement ................................................ 19

4.3 AMD Dual Graphics Setup.............................................................. 20

Chapter 5: RAID Functions .................................. 21

5.1 Operating System............................................................................ 21

5.2 Raid Arrays ...................................................................................... 21

5.3 How RAID Works............................................................................. 21

Chapter 6: T-Series UEFI BIOS & Software........... 24

6.1 T-Series UEFI BIOS ........................................................................... 24

6.2 T-Series Software ............................................................................. 27

Chapter 7: Useful Help ........................................ 37

7.1 Driver Installation Note.................................................................. 37

7.2 Extra Information............................................................................ 38

7.3 AMI BIOS Beep Code....................................................................... 39

7.4 AMI BIOS Post Code ........................................................................ 40

7.5 Conversion Of Hexadecimal and Decimal System...................... 42

7.6 Troubleshooting............................................................................... 43

Appendix: SPEC In Other Languages ................... 44

German.................................................................................................................. 44

French .................................................................................................................... 46

Italian..................................................................................................................... 48

Spanish ................................................................................................................... 50

Portuguese ............................................................................................................ 52

Polish...................................................................................................................... 54

Russian ................................................................................................................... 56

Arabic..................................................................................................................... 58

Japanese ................................................................................................................ 60

TA75A+

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

Serial ATA Cable X4

Rear I/O Panel for ATX Case X1

User’s Manual X1

Fully Setup Driver DVD X1

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

Socket FM1

AMD A-Series / E2-Series processors

AMD 64 Architecture enables 32 and 64 bit

comput ing

Chipset

AMD A75

Super I/O

ITE 8728

Provides the most commonly used leg acy

Super I/O functionality

Low Pin Count Interface

Environment Control in it iatives

H/W Monitor

Fan Speed Contro ller

ITE's "S mart Guardian" funct ion

Main

Memory

DDR3 DIMM Slots x 4

Max Memory Capacity 32GB

Each DIMM supports 512MB/

1GB/2GB/4GB/8GB DDR3

Dual Channel Mode DDR3 memory module

Supports DDR3 800/1066/1333/1600/1866

SATA III

Integrated Serial ATA Controller

Data transfer rates up to 6 Gb/s.

SATA Version 3.0 specif icat ion co mp liant.

RAID 0,1,10 support

LAN

RTL8111E

10 / 100 Mb/s / 1Gb/s auto negotiation

Half / Full duplex capability

Sound

ALC892

7.1channels audio out

Supports HD Audio

USB3.0

A75 Data transfer rates up to 600 MB/s

PCI Express Gen2 x16 Slot x2

Supports PCI-E Gen2 x16, x4 expansion cards

PCI Express Gen2 x1 Slot x2

Supports PCI-E Gen2 x1 expansion cards

Slots

PCI Slot x2

Supports PCI expansion cards

SATA Connector x6 Each connector supports 1 SATA device

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

S/PDIF out Connector x1 Supports digital audio out function

Consumer IR Connector x1 Supports infrared function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

On Board

Connectors

System Fan Header x2 System Fan Power supply

TA75A+

3

SPEC

CMOS clear Header x1 Restore CMOS data to factory default

USB2.0 Connector x3 Each connector supports 2 front panel USB2.0 ports

USB3.0 Connector x1 Each connector supports 2 front panel USB3.0 ports

Serial Port Connector x1 Connects to RS-232 Port

Power Connector (24-Pin) x1 Connects to Power supply

Power Connector (4-Pin) x1 Connects to Power supply

Back Panel

I/O

PS/2 Keyboard / Mouse x1

HDMI Port x1

VGA Port x1

DVI-D Port x1

LAN port x1

USB2.0 Port x4

USB3.0 Port x2

Audio Jack x6

Connects to PS/2 Keyboard / Mouse

Connects to HDMI cable

Connect to D-SUB monitor

Connect to DVI monitor

Connect to RJ-45 ethernet cab le

Connect to USB2.0 devices

Connect to USB3.0 devices

Provide Audio-In/Out and Mic. connection

Board Size 244 mm (W) x 305 mm (L) ATX

OS Support

Windows XP / Vista / 7

Biostar reserves the right to add or remove support

for any OS With or without notice.

1.4 REAR PANEL CONNECTORS

Line In

Line Out

Mic In

Center

Rea r

Side

USB2.0X2

LAN

USB3.0X2

HDMI

DVI-D

PS/2

Keyboard / Mouse

USB2.0X2

VGA

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

USB_KBMS1

HDMI1

VGA

DVI

RJ45USB 1

AUDIO1

USB 3_0

ATXPWR2

SYS_FAN 2

LAN

Super

I/O

Codec

PEX16_1

PEX1_1

PEX1_2

PEX16_2

PCI1

PCI2

F_AUDIO1

JSPD IFOU T1

J_C OM1 CIR1 F_USB1 F_USB2 F_US B3

SYS_FAN 1

SW_PWR1

SW_R S T1

PANE L1

JFRON T_US B3_1

SATA2

SATA1

SATA3

AMD

A75

BAT1

BIO S

ATXPWR 1

DDR3_A1

DDR3_A2

DB2DR3_

DDR3_B1

CPU_FAN1

NB_ PH1_ D1

PH 1 _D 1

PH 3 _D 2

PH 2 _D 3

PH 4 _D 4

JCMOS1

Note: represents the 1■

st

pin.

TA75A+

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only

in the correct orientation.

Motherboard Manual

6

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the

installation.

TA75A+

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

CPU_FAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

1

4

4 Smart Fan

Control (By Fan)

SYS_FAN1: System Fan Header

SYS_FAN2: NorthBridge Fan Header

Pin Assignment

1 Ground

2 +12V

SYS_FAN2

SYS_FAN1

1

3

13

3

FAN RPM

rate sense

Note:

CPU_FAN1, SYS_FAN1/2 support 4-pin and 3-pin head connectors. When connecting

with wires onto connectors, please note that the red wire is the positive and should be

connected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. DDR3 Modules

DDR3_A1

DDR3_A2

DDR3_B1

DB2DR 3_

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

TA75A+

9

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Mem ory

Size

DDR3_A1 512MB/1GB/2GB/4GB/8GB

DDR3_A2 512MB/1GB/2GB/4GB/8GB

DDR3_B1 512MB/1GB/2GB/4GB/8GB

DDR3_B2 512MB/1GB/2GB/4GB/8GB

Max is 32GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

Enabled O X O X

Enabled X O X O

Enabled O O O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

D. DDR Speed Support

Please refer to the following table for DDR speed reference: (x = 1 or 2)

# of DIMM per Channel # of Ranks per DIMM

Max DDR Speed Grade

for 1.50V DIMM

1 of 1 UDIMM xR DDR3-1866

1 of 2 UDIMMs xR, 0 DDR3-1600

2 of 2 UDIMMs 1R, 1R DDR3-1600

2 of 2 UDIMMs 2R, xR DDR3-1333

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

SATA1~SATA6: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,

it satisfies the SATA 3.0 spec and with transfer rate of 6.0Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

S AT A 1 S A T A 3

2SATA

7 Ground

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

1

23

4

4 Ground

TA75A+

11

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

Note:

Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2

connectors have been plugged-in.

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI 1

PCI 2

Motherboard Manual

12

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slots

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

PEX16_2: PCI-Express Gen2 x4 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 2GB/s per direction; 4GB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

PEX16_1

PEX1_1

PEX16_2

PEX1_2

TA75A+

13

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

P

W

R

_

L

E

D

R

S

T

H

L

E

D

S

P

K

+

-

1

916

8

O

n

/

O

f

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

Motherboard Manual

14

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and

the CMOS data. Please carefully follow the procedures to avoid damaging the

motherboard.

13

Pin 1-2 Close:

Normal Operation

(default).

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Optimal Defaults and save settings in CMOS.

J_COM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

19

210

10 NC

TA75A+

15

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header supports HD and AC’97 audio front panel connector.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

1

2

9

10

JSPDIFOUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

31

3 Ground

Motherboard Manual

16

CIR1: Consumer IR Connector

This header is for infrared remote control and communication.

Pin Assignment

1 IrDA serial input

2 Ground

3 Ground

4 Key

5 IrDA serial output

6 IR Power

1

2

5

6

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

1

20 11

10

Pin Assignment Pin Assignment

1 VBUS0 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 Ground

4 Ground 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 Ground

7 Ground 17 SSRX2+

8 D1- 18 SSRX2-

9 D1+ 19 VBUS1

10 ID 20 Key

TA75A+

17

F_USB1/F_USB2/F_USB3: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

1

2

9

10

F_ USB3

F_USB2

US B1 F _

10 NC

BIOS POST Code/CPU Temperature Indicator

This indicator will show POST code while booting. After the booting sequence,

it will show current CPU temperature through hexadecimal figure. Please

refer to Chapter 7.4 for all the BIOS POST codes, and Chapter 7.5 for

conversion of hexadecimal and decimal system.

Motherboard Manual

18

On-Board LED Indicators

There are 5 LED indicators showing system status.

NB_PH1_D1

PH1_D1

PH2_D2

PH3_D3

PH4_D4

NB_PH1_D1: NB Power Status Indicators

PH1_D1/PH2_D2/PH3_D3/PH4_D4: CPU Power Status Indicators

Please refer to the tables below for specific messages:

LED Phase Indicator

ON Phase Active

OFF Phase Disable

On-Board Buttons

There are 2 on-board buttons.

SW_PWR1

SW_RST1

SW_RST1: Reset button.

SW_PWR1: Power Switch button.

Page is loading ...

Biostar TA75A+ User manual

Related papers

Other documents